Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹40.1 LAccepted-AOC 84 A VIJAY NAGAR COLONY LALGHATI PO NAYAPURA BHOPAL 462032 | 462032 | L1 | Accepted-AOC LOWEST BIDDER | |
| 2 | L2₹40.7 L+₹26,304.50 (0.65%)Rejected-Finance | L2 | Rejected-Finance OTHER THAN LOWEST | |
| 3 | L3₹41.8 L+₹1.4 L (3.39%)Rejected-Finance | L3 | Rejected-Finance OTHER THAN LOWEST | |
| 4 | L4₹43.9 L+₹3.5 L (8.64%)Rejected-Finance | L4 | Rejected-Finance OTHER THAN LOWEST |
Tender Value
Refer Docs
EMD Value
₹96,800
Closing Date
27 Jul 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE BHOPAL
GE BHOPAL BAIRAGARH BHOPAL
SPL REP TO BLDG NO T58 AT 5221 ASC BN MT 01SRW PROVN OF INSP RAMP AT 194 FWC 02 LBW AND CERTAIN REV REV 04 AND MINOR WORKS MW 20 OF 21 22 MW 05 OF 22 23 AT SI LINES AND BAIRAGARH UNDER GE BHOPAL
2022_MES_535144_1
8909/E8
Open Tender
Civil Works
Item Rate
183 days
BHOPAL
Please refer Tender documents.
7 documents required · 7 mandatory
₹500
Yes
GE BHOPAL
₹96,800
Yes
26 Aug 2022
1 Jul 2022
29 Jul 2022
1 Jul 2022
27 Jul 2022
15 Jul 2022
Amount
Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline
Taking down chowkhats or frame nexc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed
Taking down chowkhats or frame exc 1.5 sqm but nexc 4.00 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.
S&F double rebate openable /fixed windows made of galvanised steel colour coated /powder coated (base steel as per IS 513 of 'D' quality galvanised as per IS 277 with zinc of 120 grams /sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick outer frame section 72 x 55mm, centre mullion section 72 x50 mm, shutter section 47 x20 mm, fly mesh section 40 x 20 mm and the fixed glass beading section 12 x12 mm, outer frame and mullion shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars /grills, the sections cut to length mitre joined with corner bracket, centre mullions cap, stay, handles, latch, 2 Nos tower bolts,2 Nos of heavy duty stainless steel pivot hinges per shutter and penelled with 5mm thick plain float glass and SS mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self expanding screws, including 10mm square bars welded to 6x12mm flat at a distance 150mm C/C (pitch) etc. complete all as specified and directed. Make : NCL Allek Seccolor Ltd (Model :ECO 4000) or equvalent as approved by GE)
S&F steel ventilators with side hung shutters including projecting type hinges/box type hinges with steel handle, and steel peg stay, complete including lugs glazing bars, dovetailed or welded complete all as specified and as directed.
S&F in repairs 25mm dia curtain rails, mild steel, chromium plated with fixing brackets, stops rollers etc complete all as specified and directed..
Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.
M&L for granite (any type) 20 mm thick work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter, shelves, urinal partition and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed in CM 1:4 complete all as specified and directed.
S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.
Demolition of cement concrete in ground floor, (unreinforced) paving nexc 15 cm thick (below or above GL) incl tiling if any complete all as specified and directed
M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.
M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.
M&L for Machine cut kota stone slab flooring 20-25 mm thick over and including 15mm thick screed bed in CM 1:6 etc set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed.
M&L for Machine cut kota stone slab flooring 20-25 mm thick over as in skirting and including 10 mm thick rendering in CM 1:4 set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified.
M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.
Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises complete all as specified and directed.
M&L for Glazed ceramic coloured tiles 350mm x 250mm x 7mm thick or 450mm x 350mm x 7mm thick, in vertical surfaces such as skirting, dados and risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed.
Demolition of brick work, built in Cement mortar including all quoins, arches, pillars etc complete all as specified and directed.
M&L for Brick work with fly ash bricks (Modular), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.
M&L for brick work with fly ash bricks (modular size bricks) straight or curved on plan any radius in half brick thick walls, built in CM 1:4 all as specified and directed.
Taking down cement plaster on brick or concrete surfaces, including racking out joint, hacking for key, scrubbing down with water complete all as specified and directed.
M&L15mm thick rendering in CM 1:6 on brick/concrete surfaces including finishing the surfaces even and smooth (without using extra cement) complete all as specified and directed
M&L 15mm thick rendering in CM 1:4 on brick/concrete/stone masonry surfaces including finishing the surfaces even and smooth (without using extra cement) complete all as specified and directed.
M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of exterior water base emulsion paint over a coat of primer on walls complete all as specified and as directed.
M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of cement based putty complete all as specified and as directed. Note: Putty shall be measured and paid for seperately under respective item.
M&L for applying one coat of 3mm thick white wall care putty on walls complete all as specified and directed.
S&F in repairs Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8306) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]
S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8318) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]
S&F in repairs Vitreous china wash basin, ISI marked, white, flat back, size 550 x 400mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed. [MAKE:- Somany (Model :LUX) or Prayag (Cat No 4645) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]
S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8302) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]
S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified & directed
Taking up or down 20 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.
S&F 20 mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.
S&F in repair 100mm dia CP grating complete all as specified and directed.
S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 75 mm bore complete all as specified and directed.
Dismantling water tank capacity exc 500 ltrs but nexc 1000 ltrs and removing to stores complete all as specified and directed
S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed. [MAKE:-SINTEX/ POLYWELL/ POLYCON/POLYPLASTor equivalent in make as per Appx 'C' (list of make) as approved by GE]
S&F Rolled mild steel sections conforming to Fe 410-W (Gde E-250) quality -A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified and directed.
M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.
Supplying, fabricating and fixing powder coated (minimum thickness 50 micron) aluminium sections of required size for door windows frames shutters and partitions including aluminium hinges of required size jointing cleats, screws sash fasteners, plug for fixing with walls, columns, etc complete all as specified and directed.
S&F 5.5 mm thick (black tinted) glass quality and glazing with oil putty/aluminium beads complete all as specified and directed
Dismantling of asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings, including ridge complete all as specified and directed.
S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL]
S&F Pre-painted galvalume aluminum zinc coating GI based profile steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL]
Dismantling of wall ceiling hard board /AC sheets and plywood in any thickness and any position including cover fillets complete
M&L for galvanised cold rolled steel section framework of size 600 x 600mm grid size using 24x38x0.50 (composite thickness) tee (bottom pre coated) & 24x24x0.50mm (composite thickness) wall angle including suspenders as per manufacturer’s instructions complete all as specified and directed. [Make: GABSON (Gabsec) or equivalent as approved by GE]
S&F asbestos free calcium silicate board of size 600x600x6mm, fixed to steel frame work in ceiling with & including applying two coats of oil bound distemper complete all as specified & directed. NOTE:- Cost of making frame work for light fittings, etc is deemed to be included in the quoted unit rate
Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) in any description and in any position not other wise specifically provided for complete all as specified and directed.
M&L for Reinforced cement concrete design mix M-25 as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajjas and the like complete all as specified and directed.
M&L form work to soffits of suspended slabs such as roof slabs, floor slabs, landings, beams, chajjas and similar work not exceeding 200 mm thick (Horizontal/Sloping) receive for fair finished surfaces complete all as specified and directed.
Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.
M&L for Hardcore of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.
M&L for Cement concrete, 100mm thick, 1:2:4 type B-2 using 40mm graded stone aggregate as in sub base, hardstanding, finishing cement concrete surface even and smooth without using extra cement, complete all as specified and directed.
M&L for heavy duty flooring tiles, harsh weather & UV Resistance, high abrasion resistance, MOH Hardness >6, thickness 10 mm thick, area of each tile not less than 0.09 sqm, anti slip type, laid in floors, steps, edges, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with & including 15mm thick rendering in CM 1:4 complete all as specified and directed.
M&L for Factory made, machine pressed, M-35 grade concrete interlocking paver blocks (glossy /reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 60 mm thickness with & including 50 mm thick sand cushion and joints filled with sand complete all as specified and directed.
Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in hard/dense soil complete all as specified and directed.
S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.
Supply only integral water proofing compound complete all as specified and directed.
M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement paint white or tinted complete all as specified and directed.
M&L for Factory made, machine pressed, M-40 grade concrete interlocking paver blocks (glossy/reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 80 mm thickness with & including 50 mm thick sand cushion and joints filled with sand complete all as specified and directed.
M&L for Reinforced cement concrete design mix M-25 in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed.
M&L for Reinforced cement concrete design mix M-25 in columns, pillars, posts & struts complete all as specified and directed.
M&L for Reinforced cement concrete design mix M-25 in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed.
M&L for Reinforced cement concrete design mix M-25 in chajja, complete all as specified and directed.
Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.
Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for fair finished surfaces of concrete complete all as specified and directed
Use & waste of Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for fair finished flat surfaces of concrete complete all as specified and directed.
M&L for Anti termite treatment to the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and directed.
M&L Anti termite treatment to the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed.
M&L for Anti termite treatment to the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as specified and directed.
M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.
M&L for rendering 10mm thick in cement mortar 1: 4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.
M&L for 5 mm thick rendering on fair faces of concrete surface in cm 1:3 as in ceiling finishing the surfaces fair & even without using extra cement complete all as specified and directed.
Preparing new plastered or unplastered surfaces of wall and M&L for applying two coats of distemper oil emulsion, white or tinted over a coat of primer on plastered surfaces complete all as specified and directed.
M&L for preparing new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.
S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.
S&F Framed work of rolled mild steel conforming to Fe 410-W (Gde E-250) quality -A as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; doors etc to be prepared for hanging or sliding with and including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting, running rails & guides) and hanging, fastening & fixing complete all as specified and directed.
S&F factory made Flush shutters 30mm thick, solid core construction, with block board core and plywood face panels, both face covered with decorative face veneers with lipping/frame to match complete all as specified and directed.
S&F 250mm long aluminium alloy anodised Sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed
S&F Butt hinges, extruded alluminium alloy with galvanised mild steel hinge pin, anodised and fixed, 100 mm size complete all as specified and directed.
S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed
S&F steel windows with side hung shutters including projecting type hinges/box type hinges with steel handle, and steel peg stay, complete including lugs with glazing bars, dovetailed or welded complete all as specified and as directed.
S&F steel windows with side hung shutters including projecting type hinges/box type hinges with steel handle, and steel peg stay, complete including lugs without glazing bars, dovetailed or welded complete all as specified and as directed.
S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.
M&L for factory made second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.
M&L for Preparing new or previously untreated surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.
M&L for Water proofing treatment on roof surfaces with APP modified membrane with non woven polyester reinforced, weight not less than 3 KG/SQM and thickness of membrane not less than 3mm having thermal insulation with white mineral/gravel finish on upper side of membrane uniformly embedded during manufacturing process laid in following sequence complete all as specified and directed.:- (a) Applying 10mm thick plaster in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on cleaned roof surface. After properly curing of the plaster, the roof will be tested for water tightening by ponding with water for seven days for any seepage/leakages, etc. If any seepage/leakage is observed the rectification will be carried out by pressure grouting under pressure of 5 Kg/sqcm using cement based grout. After the roof surface is repaired, the slab /roof will be again tested for water tightness before proceeding for further treatment. (b) Properly cleaning and drying of the plastered roof surfaces, parapets, gutters, drain mouths, etc for all foreign matters such as fungus, moss, dust, etc by wire brushing and dusting. Proper grooves shall be cut around CI drain outlets/pipes/chimney pipes and other similar situations to tuck in the treatment. (c) Applying a coat of bituminous primer conforming to IS: 3384-1965 @ 0.3Kg/Sqm on the prepared surface till the surface is properly impregnated. (d) Laying APP modified water proofing membrane with 100mm overlap in longitudinal direction and 100mm overlap in transverse direction sealed and bounded to the surface by torch application method. (e) All joints and changes in direction should be curved with cement mortar 1:3 with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. A fillet of PCC 1:2:4 type B0 using 12.5mm graded stone aggregates shall be provided at all junctions of vertical and horizontal surfaces and wherever there is change of direction.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.
Removing excavated materials (soil) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.
S&F Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, with & including filing of cement concrete typ B-0, 1:2:4 using 12.5mm graded stone aggregates inside frames complete all as specified and directed.
M&L for rendering 15mm thick in two coats, first coat of 10mm thick on faces of brick work or concrete surfaces in cement mortar 1: 6 and second coat (finishing coat) in cement mortar 1: 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished fair and even complete all as specified and directed.
S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.
S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panel will be of wire gauze in lieu of wood grain PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M S Solid tube and this tube will be welded to MS tubes. The wire gauge shall be stretched to tighten firmly and all as per specification, complete all as specified and directed.
S&F 15 mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.
S&F vitreous china wash down water closet pan, pedestal pattern, ISI marked, white, including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed. [MAKE:-SOMANY (Cat No.120403 & 120404)/ Prayag ( Cat No 4016) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]
S&F PVC low level flushing cistern 10 litres capacity, ISI marked, white, with all fitting and fixtures including brackets, PVC connection of 450mm long and 32 mm bore PVC flush pipe, complete all as specified and directed. [MAKE:- SOMANY (Cat No.121002), Prayag (Cat No.501 Smart flush cistern) or equivalent in PARRYWARE-SLIMLINE/CERA/ make as per Appx 'C' (list of make) as approved by GE]
S&F Vitreous china urinal half stall ISI marked, white, with & including chromium plated waste coupling including connections to flush pipe and outgoing pipes complete all as specified and directed. [MAKE:-SOMANY smart / HINDWARE (Cat No.60002 starwhite) or equivalent in CERA/PARRYWARE/ Prayag as approved by GE.]
S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8318) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]
S&F Brass chromium plated over head shower rose 125 mm size with swivel joints and brass arm 225mm and flange complete all as specified and directed. [MAKE:- Prayag (Cat No.BS-66) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]
S&F Tubular towel rail of brass, chromium plated glossy finish, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. [MAKE:- Prayag (Cat No.BA-40) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]
S&F PVC (SWR) floor/Nahani trap, plain with CP grating including jointing with solvent cement, dia of outlet 75 mm complete all as specified and directed.
S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed.
S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore complete all as specified and directed.
S&F PVC (SWR) junction single (single T), equal or unequal, 110mm bore complete all as specified and directed.
S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.
S&F PVC (SWR) vent cowl, 110mm bore complete all as specified and directed.
S&F twin angle valve cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed.
S&F hand shower (health faucet) brass with 1.0 mter long flexible tube and wall hook complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-81) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]
S&F 150 mm Aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed
S&F Salt glazed stoneware drain pipes 150 mm bore, grade ‘A’, ISI marked, laid in trenches and jointed as specified complete all as specified and directed.
M&L for Concrete bed to drain pipes 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tasted; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.
Dismantling water tank capacity exc 250 ltrs but nexc 500 ltrs and removing to stores complete all as specified and directed
S&F Rotational moulded (three layered, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity including PVC cover, hoisted and fixed in position including connecting up pipes complete all as specified and directed. [MAKE:-SINTEX/ POLYWELL/ POLYCON/POLYPLASTor equivalent in make as per Appx 'C' (list of make) as approved by GE]
Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 Sq cm in section in framed work complete all as specified and directed.
Dismantling timber scantlings 40 sq. cm and over in section, in any position unframed wk complete all as specified and directed.
M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed.
M&L for cutting holes in brick walls exc half brick but n exc one brick in cement mortar for incerting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete type B1, 1:2:4 as required, complete all as specified and directed.
Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, and applying two coats of oil emulsion distemper, white or tinted over one coat of white cement based putty complete all as specified and directed. Note: Putty shall be measured and paid for seperately under respective item.
S&F Steel work in tubular/structural trusses, purlins, etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.
S&F Mild steel work conforming to Fe-290 Gde E-165, Hand rails, half round or other steel sections or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.
M&L for preparing old painted steel & iron surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed
M&L for preparing old painted surfaces of wood and wood based materials of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.
S&F Mild steel conforming to Fe-290 Gde E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.
Dismantling structural steel work including doors, gates but excluding framed trusses complete all as specified and directed.
M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.
S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (angle type) screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed. [MAKE:- Prayag (Cat No.8310) or equivalent in MARC/ JAQUAR/ make as per Appx 'C' (list of make) as approved by GE]
M&L for 25 mm thick Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate in leveling course, benching, sub base, complete all as specified and directed.
M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.
Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.
S&F for Point wiring for light /Fan/Exhaust/bell point controlled by one switch, using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor -stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes( with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:-
All as per BOQ item No. 131.00 here-in-before, but for 3 pin socket outlet 5/6 Amp on independent board, complete all as specified and directed.
All as per BOQ item No. 131.00 here-in-before, but for one three pin outlet 5 Amp on same board with other switches, complete all as specified and directed.
All as per item No. 131.00 here-in-before but wiring with 2.5 Sq mm copper cable for 5/15 amp switch socket on independent board and provision of 2 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed. .
All as per item No. 131.00 here -in- before but wiring with 4.0 Sq mm FRLS mutistranded copper conductor cable for 5/15 amp switch socket combination on independent board and with 4.0 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.
S&F Switch piano, flush type, single pole, one way, 6 Amps, 240 volt, 50Hz, AC, ISI marked complete all as specified and as directed.
S&F Ceiling rose surface bakelite, three terminals, 240V, 50Hz, ISI marked complete all as specified and as directed.
S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings with & including LED lamp white 9 watt retrofit, 230 volts complete all as specified and directed.
Supply and fixing Polycarbonate socket outlet 2-in-1, 5 pin 5 Amps, 240 volts, flush type, complete all as specified and directed.
S&F with socket outlet flush type multipurpose 2 in 1, 5 pin 5 and 15 Amp, 230 volts, complete all as specified and directed.
S&F Polycarbonate switch piano flush button single pole one way 15 Amp 240 volt ISI marked, complete all as specified and directed.
Taking down unserviceable sub main wiring including service connections, of any size and any description including conduit pipe complete all as specified and directed.
M&L for Sub main wiring with two single core FRLS PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in non metallic rigid PVC conduit of size 25 mm dia ISI marked including PVC insulated unsheathed 6 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly, complete all as specified and directed.
Taking down existing unserviceable fitting any type any size and Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.
Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.
S&F LED light fitting 1x9W / 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.
Taking down existing u/s light fitting patti type and S&F LED 24 watt recess mounting light fitting (2 x 2 luminaire), with white powder coated CRCA housing with high power LEDs and aluminium front frame with flat white high power transmission acrylic cover including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified and directed. Make :-Orient Cat Part No -LTRAQ-24-C or equivalent in Philips/ Crompton.
Taking down main switches/MCB DBs of any capacity any type including MCBs, complete all as specified and directed.
S&F sheet metal enclosure for MCB, DB, VTPN 415 Volts 200 amps rated busbar, 4 way Double door (Vertical DB) factory made conforming to IS: 13032 fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutal link and 200 Amp, 440 volt rated bus bar, 16 KA, DB shall be semi glossy finished with epoxy polyster based powder paint sprayed (RAL 9003) and baked at high temperature with anti rust conditioning protection against corossive atmosphere, IP 43 protection class. DB shall also be provided with lable marking indicating the incoming and out going circuit including suitable size rectangular board for mounting complete all as specified and directed.
Supply and fixing 415 V 63 Amps 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning, complete all as specified and directed.
S&F MCB, SP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 6 to 32 amps including connection with suitable size aluminium / copper lugs complete all as specified and directed.
S&F ceiling fan 1200 mm sweep single phase AC 220 Volts 50 HZ, 3 blades double ball bearing and connecting including provision of 3 core flexible PVC insulated multi stranded copper conductor cable of size 0.5 Sq mm from ceiling rose/connector to fan, etc including GI down rod of appropriate length as per site requirement including taking down of old fan and depositing in AGE E/M store yard complete all as specified & directed.
S&F exhaust fan with louvers made of iron body and MS sheet baldes AC Single phase 230/240 volts, 300 mm sweep, 900 RPM including cutting for making opening in wall and making good disturbed surfaces after fixing of exhaust fan and louvers including connection with 23/.0076 three core copper wire from ceilling rose to exhaust fan upto 1 mtr length complete all as specified and directed.
M&L for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR-2009 Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by 15mm dia light grade GI pipe and watering pipe shall be 20mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed. NOTE :- (i) The concrete pit shall be PCC (1:3:6) type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) The unit rate includes the cost of GI pipe medium grade for protection of earth wire and 4mm dia earh lead wire upto 7.5 M. (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself.
M&L for Sub main wiring with two single core FRLS PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in non metallic rigid PVC conduit of size 25 mm dia ISI marked including PVC insulated unsheathed 4 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly, complete all as specified and directed.
S&F Switch socket combination 5 pin, 5/6 Amp, flush type, complete all as specified and directed.
S&F LED Lamp, 10 Watt, B22 CDL, complete all as specified and directed.
S&F Building security light fitting made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC over having top opening separate driver compartment with IP-66 protection and impact resistance of IK07 with suitable gaivanised iron pipe, light grade, brackets 1 mtr length bent to shape to obtain required shape including clamps, nuts, bolts, washers etc. connecting withsuitable flexible copper wire of size 23/0.0076, complete all as specified and directed. (Make : Havels Cat No. ENDURAPEARLS20WLED757SASYTOPCMP or equivalent in Bajaj / Surya / make as per Appx 'C' (list of make) as approved by GE]
S&F ceiling fan regulator electronic steped type 240 V, AC 50 Hz single pole, 100 watts flush type complete all as specified and as directed.
S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar 10 KA, 8 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed.
S&F MCB SP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 5 to 32 amps including connection with suitable size aluminium / copper lugs complete all as specified and directed.
S&F in repairs MCB SP suitable for 240 volts, AC supply 40 to 63 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed.
S&F in repairs MCB, SPN, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 6 to 32 amps including connection with suitable size aluminium / copper lugs complete all as specified and directed.
S&F in repairs MCB SPN suitable for 240 volts, AC supply 40 to 63 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed.
S&F 40mm GI tubing light grade with all fittings as required for passing through cables under floors, along the wall or along the pole, etc with suitable size M.S.flat iron clamps incl nut,bolt and washer including taking down old rusted pipe complete all as specified and directed.
Cutting of bituminous road/PCC hard standing/road/floor for laying of GI pipe upto 80mm dia (trench not more than 0.3m x 0.3m) for passing of cable including making good the disturbed surfaces all as per existing complete all as specified and directed.Note:-GI pipe shall be measured & paid separately under relevant items of this schedule.
Supply, laying, connecting and testing LT XLPE insulated, screened, PVC bedded, armoured, heavy duty cable with aluminium conductor of size 25 sqmm, 2 core, 1100 volts grade, laid in trenches, passing through pipes/ducts, etc including taking out old unserveciable cable, any type complete all as specified and directed.
M&L for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection (8 cm below cable & 15 cm above cable) complete all as specified and directed. [Note:-Compacted/punned thickness shall be measured & paid]
Supplying and laying sub class 'B' bricks (modular) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed
S&F 25 mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.
S&F Gun metal globe or gate valves, 25 mm bore, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed
S&F Gun metal globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed
Deduct schedule of credit (calculation will be done off line) Rs. 33960.00
M/S Shanti Traders
M/s VIKAS TRADERS
Samaksh Enterprises
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .