NIT 54 OF 2020-21 SPECIAL REPAIR TO BLDG NO T-16, T-21, T-322, SPECIAL REPAIR (E/M) TO BLDG NO T- 194 AND T-198 AND CERTAIN OTHER E/M SANCTIONED WORK AT BHALRA MIL STATION UNDER GE (I) 873 EWS

Amount

B/R Portion

Excavating in trenches, not exceeding 1.5metre wide and not exceeding 1.5metre depth for foundation, etc., and getting out in any type of soil, complete all as specified and directed.

Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick, all as specified.

Removing excavated soils exceeding 50m but not exceeding 100m and depositing where directed at a level not exceeding 1.5m above the starting point complete.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specially provided for complete including removing rubbish from the site, complete all as specified and directed.

75mm thick, plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection etc., finishing surface even and smooth without using extra cement including making joints with bitumastic filling in proportion of bitumen and sand 1:3 by weight complete as specified and directed. Note : The concrete shall be laid at a stretch not exceeding 3.0m in length and joint shall be made at every turning / corners, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

25mm thick PCC 1:2:4, type B-0 (using 12.50mm graded crushed stone aggregate) as in floor, finished rough to receive tiles above, complete all as specified & directed.

Vitrified coloured tiles of size 596mm x 596mm x 10mm thick as in floors etc. bedded & jointed in neat cement slurry over and including 15mm thick screed bed in CM 1:4 and pointed in coloured cement to match the colour of tile all as specified and directed.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, complete all as specified and as directed.

35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete as specified and directed.

Butt hinges, medium weight, cold rolled mild steel, 100mm size, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 300mm, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section and fixed complete of Size 200mm long complete all as specified and directed.

Aluminium handle cast type anodized of size 150mm complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone, concrete or brick surrounds glazed with putty or fixed with beads.

3mm thick sheet glass ordinary quality and glazing with oil putty / screws, in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and aperture 1.4mm and fixed with tinned tacks or galvanized wire staple, fixed in repairs, all as specified and directed at site

Dismantling wrought iron or mild steel work of any description not otherwise specifically provided for, complete all as specified and as directed.

Mild steel work as in wind tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimney, roofs, arches etc king rods and staining bolts conforming to Fe-290 Gde E-165 complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including nanital or similar pattern from roof covering or in ridges, hips, valley gutter and similar works complete, all as specified and directed.

Galvanised, corrugated mild steel sheeting, with two corrugation side lap fixed with 'L' type or 'J' type or cranked hooked bolts with washers in roofs, 0.63mm thick, Gde-O quality, with 120grams/sqm zinc coating and Gde 'B' (i.e. 12.5 mm) corrugation complete, all as specified and as directed.

Galvanised, corrugated mild steel sheeting, with two corrugation side lap fixed with 'L' type or 'J' type or cranked hooked bolts with washers in roofs, 0.63mm thick, Gde-O quality, with 120grams/sqm zinc coating and Gde 'B' (i.e. 12.5 mm) corrugation but except sheeting complete, all as specified and as directed.

0.80mm thick plain, Galvanised, mild steel sheeting (ISI marked) grade 'O' with minimum 120grams/sqm for zinc coating in ridges, hips, valley gutters, drip, and straight flashings, fixed with coach screws and washers complete, all as specified and as directed.

Dismantling timber scantling framed work 40 sqcm and over in section in any position complete all as specified and as directed.

2nd class hardwood in scantling clean sawn timber framed and fixed complete all as specified and directed.

2nd class hardwood plain fillets bull nosed, splayed, chamfered or rounded on one edge or face section exc 3 sqcm but n.exc 6 sqcm fixed with screw complete all as specified and directed.

Dismantling wall and ceiling board (fibre, pulp, PVC, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillets complete all as specified and as directed.

6mm thick Non asbestos fibre cement building board fixed or laid in false ceiling and including aluminium snap grid of size 610mm x 610mm with using 36.5mm x 23.5mm x 1.28mm cross tee and 25x25x1.5mm angle fixed to perimeter of wall including necessary supporting hanger with 3mm dia GI wire and J bolts, nuts and washer for securing framework to ceiling suspended @ 120 cm c/c both ways, complete all as specified and directed.

12mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work all as specified and directed.

Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Preparation of new galvanised steel surfaces to receive painting by coating with mordant solution including washing and cleaning of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

E/M Portion

Taking out carefully copper / aluminium point wiring, (Light, fan, socket or power) complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, DB's etc. including making good the disturbed surface of wall/floors, complete all as specified and as directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including PVC casing and capping and accessories of suitable size for concealed wiring including 1.50 Sqmm copper earth wire (green colour) FRLS Cable for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, mild steel sheet or cast iron boxes including making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 33 here-in-before but for one 3 pin socket outlet 5 Amp independent, complete all as specified and as directed.

All as per the description of Serial Item No 33 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 33 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 4.0 Sqm with 2.5 Sqmm copper conductor in green colour for as earth continuity conductor all as specified and directed.

Switch piano, flush type, 5 Amps, single pole, one way, complete all as specified and as directed.

Socket out let 2 in 1, 3 pin 5 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Switch socket outlet combination universal type, 2 in 1, 5 pin 5 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Switch socket outlet combination universal type, 2 in 1, 5 pin 15 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings complete all as specified and as directed.

LED Lamp 10 watts 230 volt in white colour complete all as specified and as directed. Make : Havells Cat Part No LHLDDEUEML6Z010 or equivalent in Bajaj/Philips / Crompton

Tube light fitting box type suitable for and including LED 20 tube Rod 4' long with decorative colour in polycarbonate housing and all accessories pre-wired and making connections with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connector to light fitting complete all as specified and as directed. Make : Havells 'E-Lite LED Curve' Cat Part No LHEXBXPNIN1W020 or equivalent in Philips / Wipro / Crompton / Syska

Bulk head luminaries complete with all accessories suitable for and including 1 x 10 Watts LED lamp including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 Volts 50 Hz complete all as specified and as directed. Make : Havells Cat Part No LHEOAOP7UZ6W010 / Crompton Cat Part No LBHE-10-CDL

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 8 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 6 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

MCB SP 6 to 32 Amp 10 KA 'C' Series, complete all as specified and as directed.

Isolator SPN 32 Amp, 24 Volt, complete all as specified and as directed.

1100 Volt grade heavy duty cable PVC Insulated aluminium conductor, served with inner sheathing of PVC tape and over all PVC sheathed in service connection suspended by insulating hanger not more than 1 mtr apart including 4 mm suspension wire, one twin core cable flat or circular 10 sqmm stranded conductor, including taking down old unserviceable service connection complete all as specified and directed.

Sub main wiring with two single core PVC insulated multistranded un-sheathed FRLS cable of size 4.0 Sqmm with stranded copper conductor, drawing into concealed PVC conduit / casing capping (including conduit and accessories) with continuous PVC insulated multistranded unsheathed FRLS cable earth wire of 2.5 Sqmm dia including taking out unserviceable sub main wiring, complete all as specified and directed. Note : Two run of 4.0 Sqmm wire, one run of 2.5 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade ISI marked cross sectional area 25 Sqmm 4 core in trenches including taking down old cable, complete all as specified and as directed.

XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade ISI marked cross sectional area 16 Sqmm 4 core in trenches including taking down old cable, complete all as specified and as directed.

XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade ISI marked cross sectional area 16 Sqmm 2 core in trenches including taking down old cable, complete all as specified and as directed.

XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade ISI marked cross sectional area 10 Sqmm 2 core in trenches including taking down old cable, complete all as specified and as directed.

Sand cushioning to underground cables using new dry river sand laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete, punned to 18cm, complete all as specified and directed Note : Punned thickness of 18cms shall be measured for payment.

Brick covering with width equal to length of bricks as mechanical protection to underground cable using old size sub class 'B' bricks, laid flat size 230mm x 115mm x 75 mm with length of brick perpendicular to length of cable, all as specified and as directed.

Galvanized iron tubing, light grade, 40mm bore for protection of cable with all fittings fixed to walls and ceilings or laid in floors/road crossing, complete all as specified and directed.

MCCB, FP, 200 Amp rupturing capacity 35 KA, 415 Volt with microprocessor release on existing LT panel with making suitable arrangement by minor cutting/ punching the existing panel board complete with spreader links and providing appropriate PVC insulated copper strip or wire bus bar to incoming terminals of MCCB including taking out existing unsv MCCBs, complete all as specified and as directed.

M&L Cubical type, weather, dust and vermin proof, busbar with locking arrangement of size 600mm x 600mm x 400mm, made out of CRCA sheet 3.15 mm thick with suitable size of channel for base complete with copper bus bar of 200 Amps rated copper bus bar chamber, angle iron frame which is made out of (40 x 40 x 6)mm complete all as specified and directed and comprising of the following :- (a) MCCB, FP, 100 Amp - 1 No (b) MCCB, TP, 63 Amp - 1 No (c) MCB, SP, 63 Amp - 4 No

Earthing complete with GI earth plate electrode of size 600mm x 600mm x 6mm thick buried directly to ground vertically to a depth not less than 2.25 Mtr below the ground level with top edge of earth plate not less than 1.65 Mtr below normal ground level connected to GI strip 25 x 4 mm size and earthing lead protected with 50 mm bore GI pipe, light grade, filling around with charcoal dust and salt including excavation, returning, filling of earth and disposal of surplus soil to a distance not exceeding 50 mtr and connected to GI strip by means of GI nuts, bolts and washers strip connected to earth plate including chamber PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate in concrete pit pre-cast RCC 40 mm thick reinforced with 6 mm dia round at 75 mm C/C both way with 12 mm dia mild steel plain bar lifting handle 2 Nos funnel with wire mesh 20 mm dia GI pipe light grade watering pipe and frame work complete all as shown in electrical plate No. 3 of SSR Part-I 2009 including testing on completion complete all as specified and as directed.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 Part-I, connected to test point complete, all as specified and testing on completion.

m/s vaid contractor and builders

VEER TRADERS

M/S KOTWAL CONSTRUCTIONS

SHARMA TRADERS

Bidder Name

m/s vaid contractor and builders

VEER TRADERS

SHARMA TRADERS

M/S Bilal Ahmad Wani

M/S KOTWAL CONSTRUCTIONS