Provision of infrastructure and services for installation of oxygen generation plant at MH Ahmednagar and GE (N) Ahmednagar

Amount

Excavation in trenches not exc 1.5 m wide and n exc 1.5m deep as in foundation laying of underground cable etc getting out in hard dense soil etc complete all as specified and directed by Engineer-in-Charge

M&L for PCC 1:4:8 type D2 using (40mm graded stone aggregate) as in foundations, fillings & mass concrete etc etc complete all as specified and directed by Engineer-in-Charge

M&L for Rolled section of structural steel work as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to Fe 410-W(gde-E-250) quality-A etc complete all as specified and directed by Engineer-in-Charge

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of Mangalore tile brick red pattern an colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws including dismantling corrugated steel sheeting, any gauge, thickness etc complete all as specified and directed by Engineer-in-charge

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof fixed with self tapping screws complete all as specified, colour and design as approved by GE including dismantling of plain steel sheeting, any gauge, thickness etc complete all as specified and directed by Engineer-in-charge

M&L for Hardcore of guage n. exc 63mm, of broken stone or boulders deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface etc complete all as specified and directed by Engineer-in-charge

M & L for PCC 1:2:4, type B1 (using 20 mm graded stone aggregate) 40 mm thick as in flooring, finish even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-charge

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n. exc 15 cm thick spread, levelled and rammed including watering complete all as specified and as directed.

M & L for PCC (1:3:6), type C2 (using 40 mm graded stone aggregate) 75 mm thick as in plinth protection etc complete all as specified and directed by Engineer-in-charge

M&L for Machined pressed precast concrete interlocking paver block with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade over a stone dust cushion of 30mm thick etc complete all as specified and directed by Engineer-in-charge

Material and labour for prepration of new or previously untreated steel and iron surfaces over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and directed by Engineer-in-charge

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and directed by Engineer-in-charge

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riverted or forged into spike; framed guard bars; barred iron doors; windows framed blusters walk ways railings framework of water tanks and similar work confirming to Fe 290 Gde E-165 etc complete all as specified and directed by Engineer-in-charge

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls etc complete all as specified and directed by Engineer-in-charge

S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls all as directed.

Supply and fix in repair bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge. Make:- Cat part No MOR 1020 A(Orintal series) of MARC or equivalent makes in list of makes mentioned in list of makes in Appendix `C'

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling etc complete all as specified and directed by Engineer-in-Charge

All as per item No 17 (here-in-before) but 20mm dia pipe.

Material and labour for rough dressed shahabad stone, 25 mm to 40 mm thick laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), laid and jointed pointed in cement and sand mortar (1:3) etc complete all as specified and directed by Engineer-in-charge

Material and labour for glazing with 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-charge

M&L for PCC (1:3:6) using stone aggregate, C1 solid block masonry exc. 10 cm in width straight or curved built in cement and sand motar (1:6) etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering, 15 mm thick on stone/brick / concrete surfaces in cement and sand mortar (1:6) surfaces finished even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge

Supply, laying, testing & commissioning of HT 11 KV (earthed) XLPE insulated screened PVC bedded electric power cable(heavy duty) with aliminium conductor 11000 Volts grade, circular screened wit extruded semi conducting compound in combination with copper tape, inner sheath of PVC tape galvanised steel strip flat, around and oveall PVC shheathed armourded conforming to IS 7098 Part-II, 1985 amended upto date of size 3 core 95 Sqmm, ISI marked laid in trenches or passing through pipes/ducts including taking down old cable of any size etc complete all as specified and directed by Engineer-in-charge

M& L for end termination joint kit for 11 KV grade cable heat shhrinkable joint, in door suitable for XLPE armoured aluminium conductor cable complete withh jointing materials and accessories suitable for 3 core, 95 Sqmm .

M&L for replacement earthing of poles/system with galvanised steel earth plate electrode of size 600 x 600 x 6mm thick buried vertically in ground not less than 2.25 mtr below ground level with top edge of the plate not less than 1.5 mtr below ground level and connected to GI strip 32x6 mm by means of nuts, bolts and washers and encased in and including 40mm dia GI medium grade pipe upt 2.4 m height form ground level fixed by MS flat iron clamp 40mm x 5mm with nuts, bolts and washers, GI strip fixed to base along pole and connected to over head line for providing earthing to HT pole/feeder AB switch LA complete with charcoal dust, salt packed around plate 150 mm thick including watering GI pipe, medium grade 40 mm dia with blanking cap 1.5 mtr long fixed to funnel with wiremesh complete with PCC chamber and RCC chamber over all as per Electrical Plate No 5 of SSR Part I - 2009 incl excavation and earth work in any type of starta and testing on compeltion. (Note: Any length of GI strip and 40mm dia GI medium grade pipe shall be provided upto 7.5 m

M & L for GI Strip 32mmx6mm burried in ground or Tubular pole by not , bolt and washers and suitable size of clamp etc complete all as specified and directed by Engineer-in-charge

Supply & fix exhaust fans AC three phase 415 V of size 450 mm sweep with louver etc complete all as specified and directed by Engineer-in-charge

Supply, installation, testing and commissioning of outdoor, of AC three phase , 50 HZ, 100 KVA capacity transformer step down , out door type 11000/433Volt (at No Load) copper wound , oil immersed , naturally cooled with external cooling tubes, core type delta connected on primary (HV) side and star connected on secondary (LV) side in accordance with vector symbol DYN-11/vector group-4) with neutral brought on secondary (LV ) Side & having tapping in equal steps of 2.5% from (+) 5% to (-) 7.5% on primary side by means of hand operated off load tap change /correct LT voltage on secondary side including provision of all necessary / standard fittings mainly comprising of:- (a) One cable box on primary HV side having cable glands suitable for 3 core, 95 sqmm XLPE 11 KV HT Cable consisting of 03 Nos of porcelain HT bushing with brass/gun metal bushing rods complete with nuts and washers. (b) One cable box on secondary (LV) side consisting of 04 Nos porcelain bushing with GM bushing rods complete with GM nuts and washers with one cable gland suitable for reception of out going LT PVC sheathed armoured cables of size 3.5 Core, 70 sqmm.

(c ) Oil conservator with filter type , drain valve and oil level gauge. (d) Dehydrating breather with first fill of dehydrating agent. (e ) Explosive Vents (f) Thermometer pocket on tank cover. (g) One No 100mm dia dial type thermometer vapour pressure type having range 0-120 degree centegrade with temp reading pointer, max temp indicator and resetting device. (h) Rating plate with terminal markings. (j) Two earthing terminals on tank/tank cover to facilitate fixing of 32x6mm GI Earth strip. (k) Oil Level gauge. (l) Oil Drain and filter valve (m) Oil filter hole with cap/plug with connections complete. (n) Lifting Lugs (o) Air Relief valve plug (p) Four plain solid cast steel detachable rollers. (q) First fill of fresh oil conforming to relevant IS and tested upto 40 KV dielectric strength. (r) Extra bushing for neutral outside the LT cable box for providing independant earthing for neutral.

(s) Provision of 02 No of danger boards 250x200mm size made out of 1.6 mm thick MS Plate, vitreous enameled white with letters, figures in marathi, Hindi and english of voltage and conventional skull and bones in signal red colour , one at HT side and other on LT side (t) Any other fittings /accessories so as to conform the whole transformer to IS-2026. (u) Buccholz Relay. (v) Rate include for transformer plinth of size 1200x1200x1000mm Make of Transformer : Rajasthan Transformer / Silver Line Electricals Pvt Ltd / Indian Transformer, Gurgaon/ ABB / Schneider / M/s Indo Tech Transformers.

Supply and errect two pole structure 11 m steel tubular pole consiting of anti climbling devices, PCC foundation and cross arms etc complete all as specified and directed by Engineer-in-Charge

Supply and fix HT 11 KV outdoor gang operated air break switch suitable for horizontal or vertical mounting fix type complete with 9 insulators of rating up to 200 Amps etc complete all as specified and directed by Engineer-in-Charge

Supply ad fix lightining arrestor HT 11 KV 10 KA Station flash etc complete all as specified and directed by Engineer-in-Charge

Supply, fabricate, testing and commissioning of LT Electrical out door distribution panel board floor mounted cubical type dust proof, weather proof, vermin proof, astehically designed, having atleast IP-54 degree of protection, fabricated from 3mm thick CRCA sheet with front and rear opening including bus bar chamber, continuous GI strip earth bus bar 4 strips of copper bus bar 200 Apms capacity, insulated colour sleevs, porcelain / epoxy insulators, rail channels cable alloy, danger notice board including made out of 14 gauge MS sheet over angle iron frame of size 40 x 40 x 6mm, 30 cm grounted in ground floor and 30 cm above GL including necessary excavation, foundation, PCC etc complete with locking arangement duly powder coated painted of approved colour connecting incoming & outgoing cable connection with suitable lugs, nuts, bolts, washers and cable joints, prewired complete with PVC insulated fore retardant copper conductor cable complete. The panel shall be comprising of the following :

Supply, laying and testing and commissioning 70 Sqmm LT XLPE insulated PVC bedded galvaised steel strip or wire armoured earthed electric power cable with aluminium conductor 1100 Volts grade, heavy duty in trenches / along pole or wall etc complete all as specified and directed by Engineer-in-Charge

Supply and fix medical grade copper pipe line Lloyd's certified with copper fittings as EN1254 standards Make - Janya xtrusion or equivalent as approved by GE.

15 mm dia

22 mm dia

28 mm dia

42 mm dia

Supplying, installing, testing and commissioning of double locking parking type outlet point for oxygen including requried accessories clamps nuts , bolts etc complete all as specified and directed by Engineer-in-Charge.

Supply and install Single gas Analong Alarm unit etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix Isolation valve for coper pipe including required fitting 42mm etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix Isolation valve for coper pipe including required fitting 28mm etc complete all as specified and directed by Engineer-in-Charge.

Supplying, installing, testing and commissioning of brass BPC flowmeter along with pipe line adopter and humidifier with all necessary fittings clamps, nuts and blots etc complete all as specified and directed by Engineer-in-Charge.

Supply and install Oxygen mainfold 4+4 along with tail pipe, NRVs and High flow Mox Regulator etc complete all as specified and directed by Engineer-in-Charge.

Supply and install Alloy Alluminium Bed Head panel with 6 socket and switch etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Structure for oulet and copper pipe mounting etc complete all as specified and directed by Engineer-in-Charge.

Supply and lay pipe galvanized, “Medium grade”, including fittings 50 mm (2”) dia etc complete all as specified and directed by Engineer-in-Charge.

Supply and lay pipe galvanized, “Medium grade”, including fittings 25 mm dia etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix gun metal gate Valve,conforming to IS 13095 suitable for 50 mm dia pipe etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix gate Valve, stop, screwed suitable for, 25 mm dia pipe etc complete all as specified and directed by Engineer-in-Charge.

Removing excavated soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed.

Returning, filling in, excavated soft/disintegrated rock including spreading, leveling, watering and well ramming in layers not exceeding 25cm in soft/loose soil etc complete all as specified and directed by Engineer-in-Charge

S&F 40mm dia GI tubing light grade including all fittings etc complete all as specified and directed by Engineer-in-Charge.

Supply & lay HDPE pipe 75mm bore for laying of HT cables etc complete with all accessores etc complete all as specified and directed by Engineer-in-Charge

Supply, laying and replcement of PCC covers , class HV type-1 flat size 300x180x40mm, etc complete all as specified and as directed by Engineer-in-Charge.

M&L for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, botls, washers, welding bending cold or hot, drilling holes for bolts, in any shape or size as indicated or erected and inclusive of one coat of red oxide primer, one under coat and one finishing coat of aluminium paint etc complete all as specified and directed by Engineer-in-Charge

M/s AG PATHAN

R. T. Saluji

M/S. Z.K.ENTERPRISES, AHMEDNAGAR

M/s. Sagar Traders

M/S MAHESHWARI ENTERPRISES

HG PATHAN CONSTRUCTION COMPANY

Maruti Abhiyantriki

Mangesh Murlidhar Darwade

M/s Renuka Enterprises

M/s. DADASAHEB NANA NAVSARE

M/S. SHOURYA ENGINEERS AND CONTRACTORS

KAMINS CARE