Renovation , Repairing , Modification Works at MIL WRIGHT Shop - Other Factory locations in Foundry and Forge Division, HAL BC.

HINDUSTAN AERONAUTICS LIMITED BANGALORE FACILITIES MANAGEMENT DIVISION

NAME OF THE WORK: Renovation / Repairing / Modification Works at MIL WRIGHT Shop & Other Factory locations in Foundry and Forge Division, HAL [BC]. CONTRACT NO. HAL/FMD/R-103/24-25

Name of the Contractor :

Sl. No. Specification Quantity Unit Rate in Figs [Excluding GST] Rate in Words Amount

Preamble: (1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The Tenderer shall abide by prevailing GST act. (2) L1 (lowest quote) will be determined based on the total quoted amount including GST. (3) This BOQ specification has to be read in conjunction with relevant CPWD specifications amended upto date/ detailed technical specification in tender document and tender drawings if any.

1 Demolishing brick work manually / by mechanical means built in cement mortar (1:6) including stacking of serviceable material and disposal of unserviceable material within 50 metres lead, etc., all complete as per directed by Engineer-in-Charge. 12.00 Cu m 1892.77 Rupees One Thousand Eight Hundred Ninety Two and Seventy Six Paise Only 22713.18

2 Dismantling / Taking out doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts, etc., of area beyond 3Sq m and stacking within 50 metres lead, etc., all complete as per directed by Engineer-in-Charge. 130.00 Sq m 461.89 Rupees Four Hundred Sixty One and Eighty Nine Paise Only 60045.82

3 Demolishing Nominal cement concrete 1:3:6 or richer mix (i/c equivalent design mix) manually / by mechanical means including disposal of material within 50 metres lead, etc., all complete as per directed by Engineer-in-Charge. 2.00 Cu m 2236.42 Rupees Two Thousand Two Hundred Thirty Six and Forty One Paise Only 4472.83

4 Dismantling Asbestos Cement / GI sheet roofing including ridges, hips, Valleys and gutters, etc., and stacking the material within 50 metres lead, etc., all complete as per directed by Engineer-in-Charge. 975.00 Sq m 71.02 Rupees Seventy One and One Paise Only 69242.29

5 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead, etc., all complete as per directed by Engineer-in-Charge. 100.00 Sq m 50.21 Rupees Fifty and Twenty Paise Only 5020.85

6 Disposal of moorum / building rubbish / malba / similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, etc., all complete as per directions of Engineer-in-Charge. 36.00 Cu m 453.94 Rupees Four Hundred Fifty Three and Ninety Four Paise Only 16341.98

7 Reinforced cement concrete (1:1.5:3) work in walls / drain walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc., above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement, etc., all complete as per directed by Engineer-in-Charge. 28.00 Cu m 9970.92 Rupees Nine Thousand Nine Hundred Seventy and Ninety One Paise Only 279185.70

8 Providing Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more, etc., all complete as per directed by Engineer-in-Charge. 100.00 Kgs 99.08 Rupees Ninety Nine and Eight Paise Only 9908.49

9 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections /appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket, etc., Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling C.P / brass / stainless steel screws, etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasteners to be paid for separately) Fixed portion Anodised aluminium (Powder coated aluminium (minimum thickness of powder coating 50 micron) 400.00 Kgs 487.75 Rupees Four Hundred Eighty Seven and Seventy Five Paise Only 195101.25

10 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket, etc., Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling C.P / brass / stainless steel screws, etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasteners to be paid for separately) For Shutters Anodised aluminium (Powder coated aluminium (minimum thickness of powder coating 50 micron) 100.00 Kgs 582.89 Rupees Five Hundred Eighty Two and Eighty Eight Paise Only 58288.75

11 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections /appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling C.P/brass / stainless steel screws, etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron):-Fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 400.00 Kgs 454.82 Rupees Four Hundred Fifty Four and Eighty One Paise Only 181926.68

12 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket, etc., Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling C.P / brass / stainless steel screws, etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron):-For Shutters Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15 100.00 Kgs 549.95 Rupees Five Hundred Forty Nine and Ninety Five Paise Only 54995.11

13 Supply & Fixing of Galvanised wire mesh of average width of aperture 1.40mm and nominal dia of wire 0.63 mm in aluminium frame, etc., all complete as directed by Engineer-in-Charge. (cost of aluminium frame will be paid separately) 25.00 Sq m 350.00 Rupees Three Hundred Fifty Only 8750.00

14 Providing & fixing ACP sheet 4mm thickk in Aluminium fabrication work, etc., all complete as directed by Engineer-in-Charge. (cost of aluminium frame will be paid separately) 50.00 Sq m 1600.00 Rupees One Thousand Six Hundred Only 80000.00

15 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions, etc., with EPDM rubber / neoprene gasket, etc., all complete as per the architectural drawings and the directions of Engineer-in-Charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0mm thickness (weight not less than 10kgs/Sq m) 60.00 Sq m 1382.92 Rupees One Thousand Three Hundred Eighty Two and Ninety One Paise Only 82974.99

16 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws, etc., all complete as directed by Engineer-in-Charge. 5.00 Each 1033.43 Rupees One Thousand Thirty Three and Forty Three Paise Only 5167.16

17 Providing and fixing aluminium sliding door bolts (aldrop) of [250 x 16]mm, ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868), transparent or dyed to required colour or shade, with nuts and screws, etc., all complete as directed by Engineer-in-Charge. 3.00 Each 239.42 Rupees Two Hundred Thirty Nine and Forty Two Paise Only 718.26

18 Providing and fixng aluminium handles of 125mm size, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colout or shade, with necessary screws, etc., all complete as directed by Engineer-in-Charge. 6.00 Each 60.87 Rupees Sixty and Eighty Six Paise Only 365.19

19 Providing and fixng aluminium tower bolts of size [250 x 10]mm, ISI marked, anodised (anodicoating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with necessary screws, etc., all complete as directed by Engineer-in-Charge. 3.00 Each 105.79 Rupees One Hundred Five and Seventy Nine Paise Only 317.37

20 Providing and fixing aluminium hanging floor door stopper : single rubber stopper ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws, etc., all complete as directed by Engineer-in-Charge. 3.00 Each 36.38 Rupees Thirty Six and Thirty Eight Paise Only 109.14

21 Providing and fixing bright finished Brass 100mm mortice latch and lock with 6 levers and a pair of anodized (anodic coating not less than grade AC 10 as per IS:1868) aluminium lever handles of approved quality for aluminium doors including necessary cutting and making good, screws, etc., all complete as directed by Engineer-in-Charge. 3.00 Each 798.33 Rupees Seven Hundred Ninety Eight and Thirty Two Paise Only 2394.99

22 Providing & fixing zinc alloyed (white powder coated) touch lock for aluminium/ uPVc sliding windows with necessary screws, etc., all complete, as per the direction by Engineer-in-Charge 60.00 Each 187.42 Rupees One Hundred Eighty Seven and Forty Two Paise Only 11245.24

23 Providing & fixing anodized aluminium grill (anodized transparent or dyed to required shade according to IS:1868 with minimum anodic coating of Grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. Brass / Stainless steel screws @200mm centre to centre, including cutting the grill to propoer opening size for fixing and operation of handles and fixing approved anodized aluminium standard section, around the opening all complete as per requirement, etc., all complete as per the direction by Engineer-in-Charge (Only weight of grill to be measured for payment) 250.00 Kgs 586.47 Rupees Five Hundred Eighty Six and Forty Seven Paise Only 146617.63

24 Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size [595 x 595]mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size [24 x 38]mm of length 3000mm, cross - T of size [24 x 32]mm of length 1200mm and secondary intermediate cross-T of size [24 x 32]mm of length 600mm to formgrid module of size [600 x 600]mm, suspended from ceiling usinggalvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. [12 x 50]mm long dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size [76 x 25 x 25 x 1.60]mm fixed with grid and Z cleat of size [25 x 37 x 25 x 1.60]mm thick with precut hole on both 25mm flange to pierce into [12 x 50]mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size [24 x 24 x 0.40]mm of length 3000mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall S.S screws. The workshall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge .With 15 mm thick Tegular edged light weight calcium sliciate false ceiling tiles 65.00 Sq m 2027.63 Rupees Two Thousand Twenty Seven and Sixty Three Paise Only 131796.24

25 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per Sq m as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer in-Charge. The sheet shall be fixed using self drilling /self tapping screws of size [5.50 x 55]mm with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required, etc., all complete as directed by Engineer-in-Charge. Note: A performance guarantee bond for 5 years on non-judicial stamp paper of Rs. 500/- shall be given by the contractor. The 10% of completed value of this item shall be dedcuted as defect liability deposit and the same shall be returned after sucessful completion of 5 years from the date of completion of contract / project as a whole. 1300.00 Sq m 678.62 Rupees Six Hundred Seventy Eight and Sixty One Paise Only 882204.75

26 Providing and fixing precoated galvanised steel sheet roofing accessories such as Plain Ridge (500mm - 600mm) 0.50mm (+0.05 %) total coated thickness, Zinc coating 120 grams per Sq m as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling / self tapping screws, etc., all complete as directed by Engineer-in-Charge. Note: A performance guarantee bond for 5 years on non-judicial stamp paper of Rs. 500/- shall be given by the contractor. The 10% of completed value of this item shall be dedcuted as defect liability deposit and the same shall be returned after sucessful completion of 5 years from the date of completion of contract / project as a whole. 29.00 R m 489.09 Rupees Four Hundred Eighty Nine and Eight Paise Only 14183.47

27 Providing and fixing precoated galvanised steel sheet roofing accessories such as Crimp Curve, 0.50mm (+0.05 %) total coated thickness, Zinc coating 120 grams per Sq m as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling / self tapping screws, etc., all complete as directed by Engineer-in-Charge. Note: A performance guarantee bond for 5 years on non-judicial stamp paper of Rs. 500/- shall be given by the contractor. The 10% of completed value of this item shall be dedcuted as defect liability deposit and the same shall be returned after sucessful completion of 5 years from the date of completion of contract / project as a whole. 60.00 Sq m 456.38 Rupees Four Hundred Fifty Six and Thirty Seven Paise Only 27382.71

28 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, etc., all complete as directed by Engineer-in-Charge. 2500.00 Kgs 122.83 Rupees One Hundred Twenty Two and Eighty Three Paise Only 307085.11

29 Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses, etc., The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.30% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified 2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6"), etc., all complete as directed by Engineer-in-Charge. Note: A performance guarantee bond for 5 years on non-judicial stamp paper of Rs. 500/- shall be given by the contractor. The 10% of completed value of this item shall be dedcuted as defect liability deposit and the same shall be returned after sucessful completion of 5 years from the date of completion of contract / project as a whole. 100.00 Sq m 1287.46 Rupees One Thousand Two Hundred Eighty Seven and Forty Six Paise Only 128746.06

30 Finishing with Epoxy paint (two or more coats) on Steel Work at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc., all complete as directed by Engineer-in-Charge. 250.00 Sq m 222.10 Rupees Two Hundred Twenty Two and Ten Paise Only 55525.67

31 FORM WORK:Centering and shuttering including strutting, propping etc. and removal of form for "Foundations, Footings, bases of columns, etc., for mass concrete, etc., all complete as directed by Engineer-in-Charge. 10.00 Sq m 360.28 Rupees Three Hundred Sixty and Twenty Seven Paise Only 3602.80

32 Providing 15mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement : 6 fine sand), etc., all complete as directed by Engineer-in-Charge. 150.00 Sq m 351.87 Rupees Three Hundred Fifty One and Eighty Seven Paise Only 52780.97

33 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour all complete to achieve even shade and colour as per manufacturer's specification, etc., all complete as directed by Engineer-in-Charge. 650.00 Sq m 170.56 Rupees One Hundred Seventy and Fifty Six Paise Only 110865.30

34 Providing Brickwork Above Plinth Level upto Floor V Level with common burnt clay machine moulded perforated F.P.S.(non modular) bricks of class designation 12.5 conforming IS : 2222 in exposed brick work including making horizontal and vertical grooves 10mm wide 12mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand), etc., all complete as directed by Engineer-in-Charge. 6.00 Cu m 8365.90 Rupees Eight Thousand Three Hundred Sixty Five and Eighty Nine Paise Only 50195.39

35 Providing and laying Double Charge Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/Sq m including grouting the joints with white cement and matching pigments, etc., The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily, etc., all complete as directed by Engineer-in-Charge. 60.00 Sq m 1335.51 Rupees One Thousand Three Hundred Thirty Five and Fifty One Paise Only 80130.61

36 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. a) For New/old work (Two or more coats applied @ 1.43 litre / 10Sq m. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm, including labour, material, scaffolding, safety equipments, etc., all complete as directed by Engineer-in-Charge. 650.00 Sq m 166.52 Rupees One Hundred Sixty Six and Fifty One Paise Only 108237.74

37 Providing & fixing 10" wide, 4mm thick uPVC Eaves Gutter for water collection from the roof sheet, including cost for labour, materials such as drop ends, L Corner, E Drop, L Drop & Joints, M.S. Clamps with sufficient packing to be held in position, tools & scaffolding, etc., all complete as per the direction by Engineer-in-charge. The joints shall be water tight and to be tested for leakage, after work completion. 200.00 R m 1554.00 Rupees One Thousand Five Hundred Fifty Four Only 310800.00

38 Supplying and painting to the existing old floor surface inside the hangar with two coat of chlorinated rubbersed enamel paint of approved colour and make including one coat of primer preparation of old painted surface with cleaning, scraping the existing old paint surface and making ready the floor surface to receive new paint. Scope also includes painting of one coat of yellow line marking of avg width 100mm to 150mm at the required places inside hangar floor surface. The quoted rate should be inclusive of thinner, labour , taxes, tools, brushes, loading and unloading, transportation, scaffolding, safety devices, etc., all complete as directed by Engineer-in-Charge. 380.00 Sq m 150.00 Rupees One Hundred Fifty Only 57000.00

39 Supply and application of 4mm PU flooring. a) Surface Grinder: The uneven floor shall be grinded thoroughly, made even gradient and the entire surface shall be thoroughly cleaned & made dust free, followed by removal of all existing sealant. b) 1mm scratch Coat shall be applied on the dust free surface, as base for overcoming treatment and to be cured within 6 to 8 hrs. c) PU Top coat 3mm: Self level PU concrete top coat shall be applied for better adhesion resistance, higher mechanical strength, chemical, UV resistance and better aesthetic appearance matt finish to the entire floor, curing, etc., all complete as directed by Engineer-in-Charge. 100.00 Sq m 1800.00 Rupees One Thousand Eight Hundred Only 180000.00

40 Providing and applying gangway marking 150 micron for a width of 100mm for borders applied to required pattern, line alignment with necessary marking tapes, brush as per detailed manufacturer's specification, etc., all complete as directed by Engineer-in-Charge. 60.00 R m 200.00 Rupees Two Hundred Only 12000.00

41 Turbo base Sheet 0.71mm Aluminium Circular (sinusoidal) profile with center to center pitch of 75mm, depth of 19mm, overall profile width 1250mm, cover width 1150mm, etc., all complete as directed by Engineer-in-Charge. 30.00 Sq m 1154.80 Rupees One Thousand One Hundred Fifty Four and Seventy Nine Paise Only 34643.89

42 Providing & Fixing Aluminium Wind Driven Rotary Turbo Ventilator of 600mm dia. with turbine diameter 750mm, over base sheet including labour, material, transportation, etc., all complete as directed by Engineer-in-Charge. 10.00 Each 3817.00 Rupees Three Thousand Eight Hundred Seventeen Only 38170.00

43 providing & fixing on wall face Unplasticised rigid PVC pipes of 110mm dia conforming to IS:13592, Type A, including joining with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion (i) Single socketed pipes, etc., all complete as directed by Engineer-in-Charge. 100.00 R m 346.73 Rupees Three Hundred Forty Six and Seventy Two Paise Only 34672.83

44 Providing & fixing on wall face Unplasticised rigid PVC moulded fittings / accessories such as 110mm dia Coupler conforming to IS:13592, Type A, including joining with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion, etc., all complete as directed by Engineer-in-Charge. 10.00 Each 125.08 Rupees One Hundred Twenty Five and Eight Paise Only 1250.85

45 Providing & fixing on wall face Unplasticised rigid PVC moulded fittings / accessories such as [110 x 100 x 100]mm Tee conforming to IS:13592, Type A, including joining with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion, etc., all complete as directed by Engineer-in-Charge. 4.00 Each 203.36 Rupees Two Hundred Three and Thirty Six Paise Only 813.44

46 Providing & fixing on wall face Unplasticised rigid PVC moulded fittings/ accessories such as 110mm dia Bend conforming to IS:13592, Type A, including joining with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion, etc., all complete as directed by Engineer-in-Charge. 8.00 Each 138.13 Rupees One Hundred Thirty Eight and Thirteen Paise Only 1105.05

Sub-Total (Excluding GST) Rupees Thirty Nine Lakh Nineteen Thousand Ninety Five and Eighty Paise Only 3919095.80

The Tenderer has to Quote Percentage Above / Below as Specified and Percentage Shall be Quoted in Figures. Approximate Amount Put to Tender State Above or Below Percentage in Figures [Excluding GST] Amount

Tenderer's Quote (Excluding GST) 3919095.80 BELOW % 3919095.80

Add 18% GST Rupees Seven Lakh Five Thousand Four Hundred Thirty Seven and Twenty Four Paise Only 705437.24

Grand Total (Including GST) Rupees Forty Six Lakh Twenty Four Thousand Five Hundred Thirty Three and Four Paise Only 4624533.05

Note: The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered.

WARNING: PLEASE ENTER PERCENTAGE QUOTE

HINDUSTAN AERONAUTICS LIMITED

Facilities Management Division

Pre-Qulification Profile (To Be uploaded along with Part A)

Tender Ref No. or Contract No.: HAL/FMD/R-103/24-25

Name of Work: Renovation / Repairing / Modification Works at MIL WRIGHT Shop & Other Factory locations in Foundry and Forge Division, HAL [BC].

Estimated Amount in Rs.: 4620000

Tender Notice Date : 23.11.2024

PROVISIONAL GST ID NO. for HAL 29AAACH3641R1Z3

Sl.No Description Details Enclosed / Not Enclosed Remarks

1 Name of the Individual / Firm / Company: * Mandatory Please Enter Name of the Individual/firm/company

2 Type of ownership PlsEnter Type of Ownership

If Other, please specify

3 Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc., Pls enter Details of Constitution

4 Address for correspondence: Pls Enter Address

5 (a) PAN No.: Pls Enter Pan NO

5 (b) Service Tax Registration No

5 (c ) Goods and Service Tax ID No.

6 Contact details

Contact person name Please Enter Contact person Name

Mobile No. Pls Enter Mobile No

Ph. No. with STD code

FAX No. with STD code 3 #N/A

7 Registered Contractor

If Registered Contractor with HAL Yes/ No Related Document to be Uploaded to eProcurement Portal * Category: E= 75 Lakhs - Lessthan= 100Lakhs F= 50Lakhs - Lessthan 75 Lakhs G = 25Lakhs - Lessthan 50 Lakhs H = 10Lakhs - Lessthan 25 Lakhs I = 5Lakhs - Lessthan 10 Lakhs J = 2Lakhs - Lessthan 5 Lakhs K = Lessthan 2Lakhs 0 7 E 1

Registration No. 199999 7 F 2

Category 200000 6 G 3

PEMD Amount ( If paid ) 499999 6 H 4

8 I.T Returns for past 03 years 999999 5 J 6

2024-25 Pls Select 'Yes' ' No' for IT Return for All Three years 1000000 4 K 7

9 Average annual financial turn over during the last 3 years, ending 31st March 2024 of the previous financial year [ should not be less than 30% of Amount put to tender] 4999999 3

YEAR TURN OVER IN Rs. Enclosed / Not Enclosed REMARKS 5000000 2

2023- 2024 Rs. Pls Enter Turn over in Rupees for all the 3 years 7499999 2

Average annual Financial turn over 0.00 1386000.00

Avg Annual Turnover criteria is not met 10000000 1

10 ESI & PF Nos with proof Nos Enclosed / Not Enclosed

ESI Registration No/. with proof if any Remarks if any

PF Registration No. with proof if any

11 Bank(s) details: [Copy of the cheque leaf to be uploaded]

Bank Account No. Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)

Name of the Bank

Type of Account

12 Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the last date of Tender submission solvency cal

Name of Bank & Branch Pls Enter Details to 'Name of the Bank' , 'Date of Issue','Value in Rs #REF! 28-Jun 0 40000

Date of Issue 200000 40000

Value in Rs. 200001 150000

Solvency value is NOT as per NIT

13 Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender. 1848000 500001 250000

Completed similar works during last 7 years Pls Select %of similar works completed during last 7 years 1000000 250000

Work NoI Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 1000001 500000

Brief Description of Work: Please enter Details for Work No 1 2000000 500000

Completed value of Work in Rs. 2000001 1000000

Date of Commencement of Work 4000000 1000000

Date of Actual Completion of Work: 4000001 2000000

Work No II Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 10000000 2000000

Brief Description of Work: Pls Enter Details for Work No II

Completed value of Work in Rs.

Date of Commencement of Work:

Date of Actual Completion of Work: work done

Work No III Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal #REF! 2555

Brief Description of Work: Pls Enter Details for Work No III #REF!

Completed value of Work in Rs.

Date of Commencement of Work:

Date of Actual Completion of Work:

14 Details of person holding the power of Attorney (If different from contact person)

Name Related Document to be Uploaded to eProcurement Portal

Mobile No. Pls Enter Details for Person holding Power of Attorney

Ph. No. with STD code

FAX No. with STD code

15 DECLARATION I

The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions including price bid do hereby accept all the terms and conditions laid down in the said Tender document and will abide by the same on acceptance and ward of work.

16 DECLARATION II

I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer. 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. Pls Accept the Delaration II