SPECIAL REPAIR TO BLDG NO H-8 LRW OR LIVING LINE, OFFICE AND STORE i.e FALSE CEILING, REWIRING, TILLING AT 75 MED REGT UNDER AGE B/R-I AND AGE E/M-I OF GE (NORTH) MEERUT CANTT

Dismantaling asbestos cement sheets(corrugated, semicorrugatd) in roof coverings complete all as specified and directed.

S&F Pre-painted galvaLume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to wall , fixed self tapping screws complete all as specified and directed.

S&F Pre-painted galvatume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to waall , fixed self tapping screws complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc,) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

S & F for Aluminium anodised snap grid frame work for false ceiling comprising of following section for making partitions of 605 X 605 mm size fixed to walls with rawl plugs and screws and hang to roof with s 6 mm dia. G.I. (upto 1200mm length) adjusting levelfixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners12.5mm dia. 40mm long complete all as specified size of main tee shall be :- (i) 36.5mmx25mmx1.4mm thick, Weighing 0.24Kg/Rm (ii) Cross Tee 23.5mmx36.4mmx1.4mm thick Weighing 0.191 Kg/Rm and (iii) Wall angle 40mmx25mmx2mm thick. Weighing 0.36 Kg/Rm

S & F 4 mm thick non asbestos fiber designer ceiling (E-board classic) board / tiles for insulation and accoustic purpose, 600 X 600 mm size fixed in ceiling with and including dusting of surface complete all as specified and directed

Dismantling mild steel or wrought iron work in roof trusses,gratings etc and similar work complete all as specified and directed

M&L for mild steel work in roof trusses,purlins,rafters,wind ties,crane gantries,posts,rails and fastenings and heavy bracket framing (Beam,Tee,Angle,Channel or Flat sections) including distance pieces,cleats etc complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete all as specified and directed.

Demolition brick work or stone/ boulder masonery built in cement mortar including all quoins , pillars etc completed all as specified & directed.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete al as specified and directed.

Taking down cement plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water etc.&removing rubbish to a disance not exc 250m complete all as specified and directed.

M & L for applying 15 mm thick rendering using ready mix plaster bags in CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, complete all as specified and directed. Note:- Water proofing compound shall be measured and paid seperately

Supply only integral water proofing compound complete all as specified & directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of weather proof exterior emulsion over a coat of primer complete all as specified and directed.

M & L for 15 mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, surface finished even & smooth with using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed

M&L for 3 mm thick applying a layer of putty on wall surfaces including cornics etc for proper levelling of plaster complete all as specified and directed.

M&L for complete removal of existing treatment , plastered or un-plastered surfaces of walls and applying two coats of weather proof exterior emulsion over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment , plastered or un-plastered surfaces of walls and applying two coats of oil bound distemper white or tinted over a coat of primer complete all as specified and directed.

M & L for old painted surface to steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with one coats of synthetic enamel including preparation of surfaces complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for glazed ceramic coloured / printed tiles 450mm x 300mmX7mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/coloured cement to match the tiles,over rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 for backing of Dado/ Skirting & vertical Tiles complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons laid, bedded, pointed in mortar etc complete all as specified and directed

M&L for 25 mm thick Cement concrete type-B-0 1:2:4 (12.5 MM graded aggregate) as subbase in floors complete all as specified and directed

M&L for pre-polished Machine cut kota stone slab flooring 20-25mm thick over 20 mm thick cement screed base in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

Polishing kota stone mechnically using grinder in two times coverage of area complete all as specified & directed.

M & L for pre-polished Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick cement backing coat (1:4) and jointed with with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness.(below or above ground level) Complete all as specified and directed.

M & L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for surface channel in concrete 1:3:6 (40 mm graded aggregate) for drain incl necessary formwork complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement complete all as specified and directed.concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each complete all as specifed & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4.0 Sqm each complete all as specifed & directed.

S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. Note: stainless steel butt hinges and necessary S S screws shall be paid separately.

S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (Rates inclusive of M.S. hold fast/ lugs or SS dash fasteners). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as specified & directed.

S & F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F factory made three track three shutter sliding window with frame incl stainless steel fly proof wire mesh having 0.56mm nominal dia of wire and average width of aperture 1.18mm & 5.5 mm thick glass (As approved by GE) panes fixed (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 (+) (-) 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension uPVC white colour sliding glazed window comprising uPVC multi chambered frame with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 (+) (-) 0.2 mm thick alvanized mild steel section made from roll forming porcess of required length (shape & size according to uPVC profile) including appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing grame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Rate inclusive of (Single/ double glass panes, wire mesh and silicon sealent and shall not be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made complete all as specified and directed

S&F powder coated approved colour anodised aluminium partition with sash bars, aluminium sections weighing 0.55 Kg/mtr (minimum) incl fixed with , clips, frame , necessary joining cleats, glazing clips, neoprene rubber gasket with aluminium beading screws suitable anodised fittings such as hinges, handles including powder coated anodised aluminium frame with one or more rebates including S&F 5.50 mm thick plain/tinted glass complete all as specified and directed.

S&F in repairs 20mm Dia Aluminium alloy anodised curtain rod decorative fancy type with brackets complete all as specified & directed.

S & F butt hinges, medium weight, Mild steel and fixed, size of hinges 100mm complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed

S & F floor door stopper of chromium plated body with rubber shoe fixed in door, overall length of cover plate 140 mm complete all as specified and directed.

M&L for framed work such as grills, angle grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-410-O or Fe-310-O, complete all as specified and directed

M & L for M-25 (20mm graded aggregates) for beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified & directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams rough finished surfaces of concrete flat complete all as specified & directed.

M & L for RCC Type B1 1:2:4 (20mm graded aggregate)for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed.

Formwork to rough finished surface of concrete soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified & directed.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for TMT bars 6mm to 8mm dia and over as in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F for steel rolling shutter upto height 3.5m,thickness of laths 1.25mm without ball bearing as specified including guide channel, top hood cover, anchoring rod, hasp and staple and other necessary, accessories required to function the shutter,erected in position as indicted complete:push pull or manual type complete all as specified and directed

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified & directed.

S&F ball bearing for rolling shutters complete all as specified & directed.

M & L for hard core of gauge not exc. 63mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 finished fair and even as in sub base complete all as specified and directed.

M&L for chequred cement concrete tiles of size 300x300x25 mm thick coloured rubber pressed glossy finish, set and jointed in neat cement slurry and pointed in white or colour cement to match the surace of tiles in foor/steps, over 15 mm thick screed bed or bedding layer in CM 1:6 complete as all specified and directed.

M&L for Sand filling under interlocking tiles or in foundations including watering and consolidation complete all as specified & directed

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement complete all as specified and directed

M&L for Providing cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in copings,platform,kerbs etc including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed

Taking down carefully any type of battens or conduit point wiring with conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site to match the existing complete all as specified and directed

M&L for concealed point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, FR-LSH, conforming to IS: 694-1990, PVC insulated, unsheathed copper conductor and including PVC concealed conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories / fittings, brass screws, washers etc, sunk zinc coated pressed steel terminal box 18G suitable for fixing moduler switches, sockets, regulator etc including modular inner frame and outer plate cover with continuous green earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated multi stranded, FRLS copper conductor cable, unsheathed and connected to common earth and earth dolly including cutting holes in or through the walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match complete all as directed for One light/fan point wiring controlled by one, one way switch/bell push button. The point wiring shall include the wiring of light/ outlets of any length from the distribution board via switch to the point complete all as specified and directed

All as described ser item no 64.00 here-in-before but one out let socket point 3pin 5 amps on independent board.

All as described ser item no 64.00 here-in-before but on the same board with other switches

All as described ser item no 64.00 here-in-before but using 2.5 sqmm copper conductor with 2.5 sqmm earth wire for one 15 amps socket outlet on independent board all as directed.

All as described ser item no 64.00 here-in-before but using 4 sqmm copper conductor with 4 sqmm earth wire for one 20 amps socket outlet on independent board all as directed.

S&F Modular Switch, 1 module, 6A, AC, 240V, one way ISI Marked complete all as specified and directed.

S&F Modular Socket, 2 module, 6A, 2/3 pin combined, AC, 240V, ISI Marked complete all as specified and directed.

S&F Modular Socket, 2 module, 6A /16A, 2/3 pin combined, AC, 240V, ISI Marked complete all as specified and directed.

S&F Modular Switch, 1 module, 16A, AC, 240V, one way ISI Marked wirh indicator complete all as specified and directed.

S&F 1 module modular blank plate complete all as specified and directed.

S&F of Ceiling rose, 2 phase/PVC/polycarbonate isolated body complete all as specified and directed.

S&F lamp holder (Angular / Straight), insulated body, with back plate complete all as specified and directed.

S&F 15 watt LED bulb 2 pin B22 base,100 Lumems per watt,PF≥0.9, voltage surge protection complete all as specified and directed.

S&F LED tube light fitting 20 watt with polycarbonate housing with all accessories and fixing material complete all as specified and directed.

S&F Bulkhead 10 Watt LED light fitting luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F 35W LED building security light energy saving & environmental friendly long life luminaire with high power LEDs as light source and electronic driver including all material required for fitting complete all as specified and directed.

S&F in repairs 1 module SPN metallic enclosure with a two pin and earth plug and socket with one MCB SP 20 Amps complete all as specified and directed.

M&L for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated FR-LSH, unsheathed, copper conductor cable with and including continuous earth wire of size 06 Sqmm nominal cross sectional area, single core, PVC insulated FR-LSH, unsheathed,copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing incl taking down old u/s submain wiring complete all as specified & directed.

S&F sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 08 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces incl taking down old u/s DB's complete all as specified and directed.

S&F MCB, SP, AC, 240 volts "C" series capacity of 06 to 32Amps, 10kA and making connections complete all as specified & directed.

S&F MCB SPN 40 A, AC, 240V, 10KA, ISI Marked 'C' curve incl thimble etc complete all as specified and directed.

S&F Isolator TPN, 63A, AC, 415V, ISI/CE Marked complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed.

S&F BLDC ceiling fan 1200mm sweep with fan regulator, 220CMM air delivery,BEE 5 star energy rated minimum service value≥6,copper winded motor ,anti rust powder coated aluminium blade,double ball bearing, dynamically balanced including canopy, shackel assembly,safety pin,nut bolt, down rod 2.5 Ft long with fan hanging round/squre clamp & hook as per rqmt etc electrical connection with flexible Cu conductor cable of appropriate size from ceiling rose/junction box to the fixture complete incl writing MES No. complete all as specified and directed.

Taking down existing ceiling fan of any size, CeiIing cable end,dismentalling blades ,make one set of three blades and keep them safe to deposited to E/M yard complete all as specified and directed.