COMPLETE MAINT SERVICE OF B R NATURE OF WORKS FOR OTM ACCN AND REPAIR TO FLOOR WALL TILING JOINERY PLUMBING AND OTHER MISC B R REPAIR WORKS AT VARIOUS POCKETS UNDER GE N AKHNOOR

Amount

Taking down shutters of any description n.exc 1.00 Sqm each and removing from the site complete all as specified and directed

Taking down shutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each and removing from the site complete all as specified and directed

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm and n.exc 4.00 sqm each, complete all as specified and directed.

Pressed steel frames for doors with one or more rebates of size 125x60mm including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh hold bar incl PCC 1:3:6 type B-0 as in back fill of chowkhats complete all as specified and as directed.

Pressed steel frames for doors with one or more rebates of size 105x60mm including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh hold bar incl PCC 1:3:6 type B-0 as in back fill of chowkhats complete all as specified and as directed.

35mm thick, 2nd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc devided into square with sash bars, edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site, complete all as specified and directed.

100 mm butt hinges, medium weight cold rolled mild steel, complete all as specified.

Aluminium anodised barrel tower bolt 200 mm, extruded section ISI marked complete all as specified.

Aluminium handles cast type anodised of size 125mm with screws long ISI marked complete all as specified.

Aluminium anodised sliding door bolts with hasp and stapple extruded section or cast aluminium alloy with length of bolt as 250 mm including fixing bolts complete all as specified.

Floor door stopper 100mm overall length of cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in bottom body of door complete all as specified and directed.

Aluminium bottom door seal with brushes, length 1.20 mtr, fix with screw, suitable for wooden door complete all as specified and directed.

300mm Mild steel ordinary rat tail helical door springs including roller and roller plate fixed, complete all as specified.

25mm outer dia stainless steel decorative drapery rod of thickness 20 guage for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150mm outer side from the clear opening of doors/ windows (including necessary fittings), fixed in repairs complete all as specified and as directed.

Powder coated anodised aluminium window / ventilator( glazed / gauged skeleton shutter ), (minimum thickness of powder coating 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 No. ) suitable handle (1 No.) complete all as specified and as directed.

Taking down wall panelling including any type of aluminium door, windows and partition in any position complete all as specified and as directed.

PVC wall lining/panelling consisting of 5mm thick plain colour pvc sheet inclusive of solvent cement and fixing at site on pvc frame including 5mm thick pvc sheet filet of width 35mm to make pvc frame as per manufacturers instruction and drawings, complete all as specified and directed.

10mm thick heavy duty fluted panel of any colour any design inclusive of solvent cement and fixing at wall/frame as per specification iin interior/ exterior wall complete all as specified and directed. NOTE: Colour and pattern to be approved be GE.

Texture cement stone cladding of thickness 8mm of standard weight 9.6 kg/sqm of fire resistance as per BS-476 part-IV, moisture resistant tested as per IS-14682-2000 of thermal conductivity of 0.0872 W/m-K at mean temperature of 25 degree C of any colour finished with one coat of primer and two coats of exterior emulsion paint of external wall complete all as per manufacturer's instructions and directed. Make : Everest

Door closer hydraulically regulated, aluminium extruded section body designation No. 1, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and as directed.

Double action door spring hydraulically regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made steel heavy duty in repairs complete all as specified and as directed.

Aluminium body Mortice lock,4-levers vertical type, size 100 mm with & including escutcheon plates and two keys, complete all as specified and as directed.

05 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and directed.

Steel windows/ventilator (Box type) factory made with double shutter with or without devetailed bar ( glass & glazed shutter) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts in each shutter 100mm long with & including 8mm square bar grills, complete all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh No 1/1 to 1/3 . Note:-(a) Fixed type glass panes shutter if any provided in above same window shall be measured and paid separately & area of these fixed shutter shall be deducted from total area of box type window for payment purpose. (b) Sheet glass/ wire cloth shall be measured & paid seperately under respective item

Description all as per Item No.29 above, but only fixed glass pane shutter without glazing bars.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones glazed with oil putty fixed with beads complete all as specified and directed.

03 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified.

Figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple fixed in repairs, complete all as specified.

CP Sink mixer central hole basin mixer with popup waste system with 450mm long braided hoses (15mm cartridge size) fixed in repairs all as specified.

Wall Mixer 3-in-1 System with Provision for both Hand Shower & Overhead Shower Complete with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Flanges (without Hand & Overhead Shower) fixed in repairs complete all as specified.

Hand Shower 120mm dia Round Shape Multi Flow with Cascade Effect (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System fixed in repairs complete all as specified.

Bib cock 15mm dia bore, fancy type choromium plated cast copper alloy with capstan head fixed in repairs all s specified and directed.

Angle cock with wall flange , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe fixed in repairs, complete all as specified.

Pillar tap of 15mm bore dia fancy type capstan heads, chromium plated screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed in repairs complete all as specified and directed.

Florentine single lever surgical purpose elbow action basin mixer with extended operating lever without popup waste system with 450mm long braided hoses in repairs complete all as per Jaquar Cat Part No-FLR-5033B or equivalent cat part of make as mention in list of make P.S as approved complete all as specified and as directed.

Brass chromium plated health faucet with one metre long flexible tube and wall hook fixed to iron pipe fixed in repairs complete all as specified and directed.

Urinal spreader of PTMT of size 15mm bore complete all as specified and directed.

Chromium plate Stainless Steel towel rail 60cm long including brackets in repairs, complete all as specified and directed.

Towel ring of brass chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats etc fixed in repair, complete all as specified.

Waste coupling of chromium plated brass 32/40 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basin fixed in repairs complete all as specified .

PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore fixed in repairs, complete all as specified and as directed.

Vitreous china wash basin, white, flat back, size 550x400mm including CP mixer for mixing hot and cold water for pipe of bore 32mm, waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets and waste pipe etc., fixed in repairs complete all as specified and as directed. Cat Part No. 10036 of Hindware (Model-Windsor) or equivalent cat part of make as specified in the list of makes as approved by GE.

PVC valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs complete all as specified and as directed.

Plastic water closet seat cover (white) closed pattern with flat bottom and cover including chromium plated hinges device fixed in repairs, complete all as specified and as directed.

Vitreous china wash down water closet pan pedestal pattern in white colour with 'P' or 'S' traps excluding seat cover, flushing cistern and flush pipe fixed in repairs complete all as specified and directed. Cat Part No-20011 (SLICK) of Hindware or equivalent cat part of make as specified in the list of makes as approved by GE.

Vitreous china squatting pan "Orissa Pattern" size 580 x 440 mm in white colour with integral foot rest incl lime mortor, 'S' trap fixed in repairs complete all as specified and directed. Cat Part No-20042 (ORISSA PAN (ECO)) of Hindware or equivalent cat part of make as specified in list of makes as approved by GE.

Supply and fixing in repairs single piece Rimless bowl with ciestern for extended wall hung WC with PP soft close seat cover,hinges ,dual flush ciestern fittings,and all accessories as per Jaquar Cat part No- FLS-WHT-5353PPZ or its equivalent in all as specified and as directed as approved by GE.

Supply and fixing repairs table top wash hand basin of size 425x340x175mm of jaquar Cat part No-CNS-WHT-903 or equivalent cat part of make as mentioned in list of make complete all as specified and as directed to P.S as approved.

PTMT Grating Round 140 mm dia fixed in repairs complete all as specified.

Waste pipe for SINK/WHB/Urinal for 32/40mm dia fixed in repairs all as specified & as directed.

Dismantling water tanks and removing to store of cap exc 500 but n.exc 1000 ltr all as specified.

Dismantling water tanks and removing to store of cap exc 250 but n.exc 500 ltr all as specified.

Rotational moulded polyethylene 03 layer water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed.

Rotational moulded polyethylene 03 layer water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed.

Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc., complete all as specified and as directed.

Mild steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Mild steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

20mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed to walls and ceilings or laid in floors, complete all as specified and as directed. Note for srl item No 81 & 82 : Cutting chases to brick or concrete surface for laying under ground pipes if required at site & making good the same with CM 1:3 shall be inclussived in rates to be quoted by the contractor.

UPVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors fixed in repairs, complete all as specified and as directed .

UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center fixed in repairs ,complete all as specified and as directed.

UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors fixed in repairs, complete all as specified and as directed.

UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center fixed in repairs ,complete all as specified and as directed .

Supply and fixing in repair UPVC (SWR) , bends with access door for 75 mm bore , complete all as specified and as directed.

Supply and fixing in repair UPVC(SWR) , bends with access door, for 110 mm bore complete all as specified and as directed.

Supply and fixing in repair UPVC branch piece, single (single 'Y') with access door for 75 mm bore complete all as specified and directed.

Supply and fixing in repair UPVC branch piece, single (single 'Y') with access door for 110 mm bore complete all as specified and directed.

Supply and fixing in repair UPVC branch piece, double (double 'Y') with access door for 75 mm bore complete all as specified and directed.

Supply and fixing in repair UPVC branch piece, double (double 'Y') with access door for 110 mm bore complete all as specified and directed.

Supply and fixing in repair UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 75 mm bore , complete all as specified and as directed.

Supply and fixing in repair UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 110 mm bore , complete all as specified and as directed.

S&F in repair UPVC (SWR) , reducers 110 mm dia complete all as specified and directed.

S&F in repair UPVC (SWR) vent cowl 75 mm dia complete all as specified and directed.

Supply and fixing in repair UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

UPVC (SWR) multi floor trap with grating including jointing with solvent cement (75mm diameater for outlet in mm) complete all as specified.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floors by picking,sweeping clean and washing down with water to remove dust etc and brushing with neat cement slurry using cement at 3kg/sqm complete all as specified and as directed.

Glazed ceramic coloured Digital tiles in vertical surface 300x450x7 mm thick Glosy finish, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified. (Sample as approved to be kept in GE's sample room)

Glazed ceramic coloured Digital tiles in vertical surface 300x600x7 mm thick Matt finish, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified. (Sample as approved to be kept in GE's sample room)

Material and labour glazed ceramic coloured HD(High depth) punch tiles in Elevation tiles 300x600x7 mm thick Matt finish, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified. (Sample as approved to be kept in GE's sample room)

Non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) in floors etc area of each tiles exceeding 0.11 Sqm but not exc 0.18 Sqm. Set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over & including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and as directed.

Description all as per srl item No 89 above but as in skirting over & including 10 mm thick plaster in cement and sand mortar 1:4, complete all as specified and directed.

Vitrified ceramic tiles (light shade) 10mm thick (Square/reactangular) area of each tiles exceedings 0.18Sqm but not exceeding 0.38sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 complete all as specified.

Description all as per item No-91 above but in vertical surfaces such as in skirting, dado etc.fixed over and including 10mm thick plaster in CM (1:4), complete all as specified and directed.

Demolition of stone slab and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick as in riser of steps, skirting, dado and pillar, jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete laid over & including 15 mm thick in CM 1:4 screed for laying Kota Stone, complete all as specified and as directed.

Machine cut kota stone 10-12 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and Mirror polishing set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/colour of tiles over and including 10 mm thick rendering in cement mortar 1:4, as in vertical surfaces complete all as specified and as directed.

Material and labour for Precast factory made interlocking designer tiles glazed top made in white cement and pigment base of thickness not less than 19 mm in different colour and pattern (compressive strength not less than 250 Kg/SqCm) set and jointed in neat cement slurry (colour and pattern to be approved by GE) all as specified and directed.

Precast factory made interlocking designer tiles glazed top made in white cement and pigment base of thickness not less than 19 mm in different colour and pattern (compressive strength not less than 250 Kg/SqCm) set and jointed in neat cement slurry(colour and pattern as approved by GE) including 15 mm thick screed bed in CM 1:4 all as specified and directed.

Machine pressed precast concrete interlocking paver block of any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 grade, laid jointed & pointed with grey cement and pigments, including watering and consolidation all as specified and directed. Note:-The shape, size and colour of paver block shall be as approved by GE.

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

16-18mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking platform laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and moulding the edges, complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. Note :- Form work required for these items included in the unit rate of this item.

Plain cement concrete type C-1, 1:2:4 ( using 20mm graded crushed stone aggregate), 50 mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair on top without using extra cement with 6mm wide joints throughout the thickness of plinth protection in concrete bays and in between the walling and plinth protection, filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand ( all by weight) complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base floor finishing surface even and fair, complete all as specified.

100mm thick Plain Cement concrete Type D-2, 1:4:8 (using 40mm graded crushed aggregate) as in sub-base of floors, path/hardstandings etc, finished even and rough to receive topping layer complete all as specified.

Taking down cement plaster of any description on stone or brick walls etc. including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

15mm thick cement plaster rendering in CM 1:6 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

Rendering 10 mm thick cement plaster with cement mortar(1:4)on other than fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Preparation of old painted surface of steel not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer, complete, all as specified.

Preparation of old treated wooden surfaces of any description over 10 cm width or or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified.

Preparation of old painted surfaces by washing, rubbing down and stopping of distempered or painted walls and applying one coats of oil bound distemper incl two coats of wall care putty of 1-2 mm thick complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over two coats of wall care putty of 1-2 mm thick complete all as specified and as directed.

Preparation of old painted surfaces by washing, rubbing down and stopping of distempered or painted walls and applying one coats of cement base paint white or tined, complete all as specified and as directed.

Preparation of old decorated surface including washing,scrubbing down and stopping of painted surfaces and applying one coat of white wash on ceiling, complete all as specified and as directed.

Preparation of newly plastered surfaces & applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on wall, complete all as specified and directed. Note for item No-28 & 29:- (i) The work shall be carried out in different shade and the same shall be got approved from Engineer-in-charge/GE/ (ii) The work shall be carried out upto 4th storey of bldgs and no extra payment shall be admissible for necessary form work & scaffolding required for the same.

Preparation of old painted surfaces with complete removal of existing treatment & applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on wall complete all as specified and directed.

Removal of all loose particles ,dust and any grwoth like fungus or algae using a wire brush and water, and filling the cracks,and all surfaces with crack pillar and applying putty as per required thickness(min 3mm) to ensure smooth surfacces and lightly wet the surfaces, and applying any design and pattern of Asian/Berger texture/stone granular using a putty blade or trowel/any type of tools to apply mixture on the prepared surfaces move uniformly across the surfaces with trowel to achive desired texture and even finish complete all as per manufactures instruction and entire satisfaction of Engr-In-Charge.

Demolition of brick work built in cement mortar including all quions, arches , pillars etc.

Brick work with sub class 'B' bricks , straight or curved on plan exc. 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

Description all as per item No.120 above, but except bricks, all as specified and directed.

Brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 in half brick thick, complete all as specified.

Rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified and as directed.

Rendering 5mm thick cement plaster with cement mortar(1:3) on concrete surface as in ceiling finished even and smooth without using extra cement, complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed

Preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed

Preparation of newly plastered surfaces of wall and applying two coats of cement base paint complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening primer complete all as specified and as directed.

Preparation of old painted surfaces by washing, rubbing down and stopping of distempered or painted walls and applying one coat of oil bound distemper white or tined, complete all as specified and as directed.

40mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in flooring finishing surface even and fair, complete all as specified.

Glazed ceramic tiles 450 x 300 x 7mm thick / 600 x 300 x 7mm thick (coloured) on vertical surfaces such as skirtings, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

20 mm thick makrana white marble as in border/cooking platform etc, bedded and jointed over 20mm thick screed in cement mortar 1:6 including pointing in white cement 1:2 using marble dust including cutting and polishing complete all as specified and as directed.

Vitreous china Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), with grating and union for discharge pipe including bedding urinal against wall in cement mortar 1:2 & securing urinal to plug with brass screws fixed in repairs complete all as specified and directed.

16mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Refixing old steel tubing and connections of 20mm bore in new or old position (Walls, ceiling, floors etc.) including cleaning for refixing complete all as specified and as directed.

Refixing old steel tubing and connections of 15mm bore in new or old position (Walls, ceiling, floors etc.) including cleaning for refixing complete all as specified and as directed.

20mm bore gun metal glove or gate valve with iron wheel head screwed bith end for iron pipe and fixed in repairs, complete all as specified and as directed.

Taking down eaves gutters and rain water pipe , soil and waste pipe (any size or pattern), includding all fittings, heads , shoes bends , swan-necks etc . complete all as specified.

110mm bore PVC SWR Type-B pipes (pressure not less than 6 kg /cm2) single socket in any length with rubber joints laid in floors/trenches etc all as specified and directed.

110mm bore PVC SWR Type A pipes ( pressure not less than 4 kg /cm2) single socket in vertcal length for rain water with rubber joints fixed to walls with PVC//MS holder clamps complete all as specified and directed.

75mm bore PVC SWR Type-B (pressure not less than 6 Kg/cm2) pipes single socket in any length with rubber ring joints laid in trenches or in floors etc all as specified and directed.

75mm bore PVC SWR Type-B (pressure not less than 6 Kg/cm2) pipes single socket in any length with rubber ring joints fixed to walls etc all as specified and directed.

PVC SWR complete bends any radius 110 mm bore with oval access door all as specified.

PVC (SWR)110 mm junction single, (Single T) equal or unequal ordinary or inverted with spigot or socket branch with oval access door all as specified and as directed.

PVC (SWR) 75 mm junction single, (Single T) equal or unequal ordinary or inverted with spigot or socket branch with oval access door all as specified and as directed.

PVC (SWR) 75 mm dia floor trap plain with grating including jointing with solvent cement fixed in repairs, all as specified and directed.

PVC SWR bends any radius 75mm bore complete all as specified and directed.

PVC (SWR) branch piece of 110 bore pipe, single (single Y) equal or unequal ordinary or inverted (spigot or socket type) provided with access door complete all as specified and directed.

PVC (SWR) branch piece of 75 bore pipe, single (single Y) equal or unequal ordinary or inverted (spigot or socket type) provided with access door complete all as specified and directed.

PVC vent cowls 110mm complete all as specified directed.

PVC 75mm vent cowl complete complete all as specified.

Stack clamp out of 50mm by 5mm flat iron and 16mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof of 100mm bore of pipe.

Stack clamp out of 50mm by 5mm flat iron and 16mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof of 75mm bore of pipe.

Taking down and refixing including resecuring and easing shutters area exceeding 1.00 sqm and n.exc 2.00 Sqm each in the same opening complete all as specified and as directed.

35 mm thick Flush shutters, solid core with particle board exterior grade as per IS-2202 of 199 (Part-I). Flush door shutter shall be internally lipped as per clause 8.52.2 of SSR-2009 Part-I complete all as specified and directed.

Pre laminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber frame in repairs as cupboard shelve and shutter, 12 mm thick. (Kitchen cup board/covered bottom shelf of cooking platform) fixed in repairs complete all as specified and directed.

Pre laminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber frame in repairs as cupboard shelve and shutter, 19 mm thick in repairs, complete all as specified and directed.

External teak wood lipping 6 mm thick fixed with nails for 18/19 mm thick board, complete all as specified.

Figured glass pin headed type, 4mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified.

75 mm butt hinges, medium weight cold rolled mild steel, complete all as specified.

Aluminium handles cast type anodised of size 100mm with screws long ISI marked complete all as specified.

Aluminium anodised barrel tower bolt 150 mm, extruded section ISI marked complete all as specified.

Aluminium anodised sliding door bolts with hasp and stapple extruded section or cast aluminium alloy with length of bolt as 300 mm including fixing bolts complete all as specified.

Curtain rail, 20mm dia Stainless steel fixed with and including two Nos of bracket & side cup including taking down of old curtains rods, complete all as specified.

Brass chromium plated fancy type wall mixture for mixing of hot and cold water supply screwed down including connecting leg & wall flange for iron pipe 15 mm bore fixed in repair complete all as specified and as directed.

Glass corner shelf assembly consisting of 5.5 mm thick sheet with chromium plated bracket guard and railing 45 cm long complete all as specified and directed.

Chromium plated brass towel rail 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified and as directed.

Stainless steel gratings 100/125mm dia fixed with cement motar fixed in repairs, complete all as specified and as directed.

M/S KARAN SINGH CONTRACTOR (BID ID -3501886)

M/S RSJ BUILDER AND SUPPLIERS (BID ID -3501913)

PACHNANDA BUILDERS (BID ID -3507564)

M/s Chopra Constructions (BID ID -3507528)

m/s vaid contractor and builders (BID ID -3495484)

bushan kumar (BID ID -3507378)

M/s Rajesh Kumar Contractor (BID ID -3501610)