Maintenance of Various colonies under South Zone.

Routine maintenance, operation of 2 nos. booster pump sets, 25 KVA Diesel Generator set, Electrrical installation and street light etc.by deploying Skilled maintenance staff complete as per term & condition attached as reguired.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete i/c credit for dismantled material with connections, testing and commissioning etc. as required. i.)Single pole

Double Pole

Triple pole and neutral 63 Amp.

Supply of following XLPE insuleted , XLPE/PVC sheethed Alumimium contoter ,Armoured power cable of 1.1KV grade i/c testing etc and credit for dismantal material. a) 2 x 10 Sq.mm.

b) 4 x 25 Sq.mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. a)Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. a)Upto 35 sq. mm (clamped with 1mm thick saddle)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. a) 4 X 25 sq. mm

b) 2 x 10 Sq.mm.

Repair ,maintenance & overhauling of existing pump sets up to 12.50HP, 3 phase,415 Volts A.C.,2900 rpm rating from authorised service providers including inspection, to and fro transportation, dismantling & reassembling, painting after replacement of motor rewinding kit ,replacement of any defective parts,i.e. EP impellars,bearing bush,pump shaft ,water seal,cable,cable seal ,coupling bush,ss screws,welding,testing etc.complete as required.

Supplying & fixing of MNX contractor L&T make suitable for motor p/set i/c connection etc. as reqd.

Supplying & fixing of relay L&T make suitable for motor p/set i/c connection etc. as reqd.

Supplying & fixing of timer L&T make suitable for motor p/set i/c connection etc. as reqd.

Supplying, Installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -50C to 400C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K /4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim (LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ))

Supplying & fixing of Battery Exide make 12V, 90AH suitable for 25KVA DG set including connections,testing and commissioning etc as required.

Repair and servicing of 25KVA ,415/440 V,DG set along with AMF/Control panel including providing & replacing following spares,testing,commisioning etc as required. i.)Valvoline Premium Genuine Oil 20 Liters CAN -1No. ii)Lub Oil Filter(06.436.01.0.00)-1 No. iii)Fuel Filter Element(03.922.42.0.00)-2 No. iv)Lock Left(06.594.97.0.00)-1 No v.)Lock Right(06.598.05.0.00)-1 No vi)Pri Air Filter Element(F6.729.07.0.00)-1 No. vii)VALVOLINE COOLANT PREMIX 10 LITRE CAN(82.020.35.1.26)-1 No. viii)Hose clamp(F6.377.16.0.00)-4 No. ix) Fuel Pipe Set(01.691.01.0.00,02.691.02.0.00)-2 Nos x)Control relay-2 Nos