Provision of toilet blocks and certain other sanction works in the area of AGE B/R II under GE (N) Ahmednagar

Amount

Excavation in trences n.exc 1.5m wide and n.exc 1.5m in depth for foundation soft/disintegrated rock and getting out etc complete all as specified and direcrted by Engineer-in-Charge

All as per Sl item No 01 (here-in-before) but hard / dense soil

M&L P.C.C (1:4:8) type D-2 using graded stone aggregate, in foundations, filling and mass concrete etc complete all as specified and direcrted by Engineer-in-Charge

Returning, filling including spreading levelling, watering and well ramming in layers n.exc 25cm in soft/loose soil etc complete all as specified and direcrted by Engineer-in-Charge

Removing excavated (soil) material n.exc 50m and depositing where directed at a level n. exc 1.5m above the starting point etc complete all as specified and direcrted by Engineer-in-Charge

Rough finished wooden form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and direcrted by Engineer-in-Charge

Rough finished wooden form work to sides of pillars, posts, struts, piers, columns and Stanchions etc complete all as specified and direcrted by Engineer-in-Charge

Rough finished wooden Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and direcrted by Engineer-in-Charge

Rough finished Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick(Horizontal or sloping) etc complete all as specified and direcrted by Engineer-in-Charge

M&L for concrete bed to drain pipes in PCC (1:4:8) type-D2 using 40 mm graded stone aggregate including packing under, and haunching against the sides of pipes for 200 mm bore pipes after they are laid and tested; etc complete all as specified and directed by Engineer-in-Charge

M&L for pre cast RCC manhole cover slab in (1:2:4) type -B1 using 20 mm graded stone aggrgate incl necessary form work and set in cement and sand mortar (1:6), cover slabs (for man holes etc) etc complete all as specified and directed by Engineer-in-Charge

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed by Engineer-in-Charge

M&L for RCC M25 Design Mix using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and direcrted by Engineer-in-Charge

M&L for RCC M25 Design Mix using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc complete all as specified and direcrted by Engineer-in-Charge

M&L for RCC M25 Design Mix using 20 mm graded stone aggregate as in roof slabSlabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and direcrted by Engineer-in-Charge

M&L for RCC M25 Design Mix using 20 mm graded stone aggregate as in Chajjas etc complete all as specified and direcrted by Engineer-in-Charge

M&L for RCC M25 Design Mix using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers,lintels over 1.5m span etc complete all as specified and direcrted by Engineer-in-Charge

M&L Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and direcrted by Engineer-in-Charge

All as per Sl item No 18 (here-in-before) but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and direcrted by Engineer-in-Charge

M&L for hardcore or gauge of broken bricks n.exc 63mm, deposited spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface etc complete all as specified and direcrted by Engineer-in-Charge

M&L for moorum filling in floors or paving laid in layers n.exc. 15cm thick spread levelled and rammed including watering etc complete all as specified and direcrted by Engineer-in-Charge

M&L for P.C.C (1:4:8) type D-2 using graded stone aggregate, 75mm thick in sub base for floor etc complete all as specified and direcrted by Engineer-in-Charge

M & L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mt centre to centre and at every turning & filling the joints with bitumen & sand mixture etc complete all as specified and direcrted by Engineer-in-Charge

M & L for PCC (1:2:4) type B1 using 20mm graded stone aggregate as in surface channels and drain etc complete all as specified and direcrted by Engineer-in-Charge

M & L for PCC (1:3:6) type C-1 using 20mm graded mechanically crushed stone aggregates as in cills, steps, bands, copings, bed plates, kerbs, hold fasts blocks etc including weathering slightly rounded or chamfered angles of throating including form work etc complete all as specified and direcrted by Engineer-in-Charge

S&F Steel ventilator with top hung shutter incl hinges, steel peg stay all as directed, glazing shall be measured and paid separetly. etc complete all as specified and direcrted by Engineer-in-Charge

M&L for 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 sqm in each pane etc complete all as specified and direcrted by Engineer-in-Charge

Supply and fix mild steel butt hinges medium weight cold rolled of size 100mm etc complete all as specified and direcrted by Engineer-in-Charge

Supply and fix aluminium anodised barrel tower bolt of extruded section 150mm long etc complete all as specified and direcrted by Engineer-in-Charge

Supply and fix aluminium anodised handles of extruded section 150mm long etc complete all as specified and direcrted by Engineer-in-Charge

Material and labour for coloured glazed ceramic tiles digitally printed premium series of size 300x450mm , 8-10 mm thick as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in cement and sand mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles etc complete all as specified and direcrted by Engineer-in-Charge

Material and labour for Anti skid ceramic coloured tiles to match dado tiles makes as specified in PS,7-8 mm thick area of each tile 400x400mm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tiels etc complete all as specified and direcrted by Engineer-in-Charge

M & L for 15 mm bore GI tubing medium grade with all fitting and fixed complete on walls, ceilings or laid in floors etc complete all as specified and directed by Engineer-In-Charge.

M & L for 20 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and directed by Engineer-In-Charge.

S & F PVC connections 15 mm size with PTMT nuts of length 450 mm etc complete all as specified and direcrted by Engineer-in-Charge

Supply and fixing stop cock cast copper alloy, fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and direcrted by Engineer-in-Charge

M&L for Grating doom 100mm dia of brass chromium plated (Minimum weight 25gms) etc complete all as specified and direcrted by Engineer-in-Charge

S&F rotational molded polyethylene water storage tanks double layered (cylindrical vertical with closed top) of 1000 litres capacity, triple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe, tank nipple and connected etc complete all as specified and direcrted by Engineer-in-Charge

S&F Factory made solid panel PVC door shutter30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete Type C1 (1:3:6) using 20mm graded stone aggregate set in cement and sand mortar (1:6) etc complete all as specified and direcrted by Engineer-in-Charge

Material and labour for preparation of new steel surfaces of any description exceeding 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and direcrted by Engineer-in-Charge

M&L for rendering 15 mm thick in cement and sand mortar (1:6) on fair faces of brick work or concrete surfaces and surface finished even and smooth without using extra cement etc complete all as specified and direcrted by Engineer-in-Charge

S&F vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistern etc complete all as specified and directed by Engineer-in-Charge.

S&F 10 ltr capacity white PVC valve less, symphonic action type, flushing cistern, low level, all accessories etc complete all as specified and directed by Engineer-in-Charge.

M&L for fendering 15 mm thick in cement and sand mortar (1:4) on fair faces of brick work or concrete surfaces and surface finished even and smooth without using extra cement with WPC mixed at 2% of weight of cement used etc complete all as specified and direcrted by Engineer-in-Charge

Supply only integral water proofing compound etc complete all as specified and direcrted by Engineer-in-Charge

S&F 110 mm dia PVC (SWR) pipes, single socketed, in any length, with rubber rings 75mm dia etc complete all as specified and direcrted by Engineer-in-Charge

Supply and fixing PVC (SWR) pipe 75 mm bore single socketed in any length with rubber ring fixed to wall with approved solvent/adhesive etc complete all as specified and direcrted by Engineer-in-Charge

Material and labour for providing water proofing treatment on roofs, as per manufacturer's instructions and as specified after taking down/out as existing tar felt at site :- (a) Cleaning the newly plastered surfaces with wire brushes and applying a coat of bituminous primer @ 0.30 ltrs/sqm and allow to dry. (b) Applying and laying torch APP polymer modified bituminous membrane 3 mm thick with non woven polyester mat as reinforced weighing not less than 3 kg/sqm by thermo fusion process as per manufacturers specification including applying one coat of aluminum paint.

M&L for rendering 10mm thick in cement and sand mortar (1:4) over concrete surfaces finished even and smooth etc complete all as specified and direcrted by Engineer-in-Charge

M&L 300 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars including cutting in to existing manhole and necessary making good of disturbed portion etc complete all as specified and direcrted by Engineer-in-Charge

All as per Sl item No 52 (here-in-before) but 200 mm

M&L for preparation of newly plastered surfaces and appying three coats of white wash on walls etc complete all as specified and direcrted by Engineer-in-Charge

M&L for preparation of newly plastered surfaces and appying three coats of white wash on ceiling etc complete all as specified and direcrted by Engineer-in-Charge

M & L for preparation of new plastered surface of walls and applying 2 coat of cement paint external surfaces etc complete all as specified and direcrted by Engineer-in-Charge

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories with provn of PVC boxes and fixed with brass screws cup washer for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as earth continuity conductor to common earth & connecting to earth dolly for the following, etc complete all as specified and directed by Engineer-in-Charge Note : 1. Porper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, bulkhead lights, bldg security light etc

One light point controlled by switch 5 Amp single pole one way

One fan point controlled by switch 5 Amp single pole one way

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

All as per Item No 57 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase, Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board

S&F switch piano flush type single pole, one way 5/6 Amp etc complete all as specified and directed by Engineer-in-Charge Make.Havells/Anchor/legrand

S&F Switch socket combination two in one, 5 Amp flush type 230V AC etc complete all as specified and directed by Engineer-in-Charge

S&F Switch socket combination 5 Amp / 16Amp, five in one, 5 / 15 Amp 230V AC etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

M&L ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge

S & F in replacement double door Sheet metal enclosures factory made DBs SPN, 8 way ,240 volts ,protection class IP-42, suitable for fixing of MCBs, etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing MCBs, SPN, AC, 240 volts of 40 Amps capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge Make .Havells/L&T/Schnider

Supply and fix Industrial type Decorative ultra slim square profile LED lighting fixture with extruded , environmental friendly, energy efficient ready to use pack LED Tube light fitiing 20 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. Earth pit not less than 2.25 m depth and top edge of the earth plate not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nuts, bolts & washer etc. Earth wire connected upto main earth point / DBs alongwith 15mm dia earth protection pipe from top edge of the earth plate to main earth point to be connected and 20mm dia watering pipe light grade with funnel and provn of PCC using cement concrete (1:2:4) mix type B1 using granded stone aggregate and RCC pit cover 50 mm thick precost RCC (1:2:4) mix type B1 duly reinforced with 8 mm dia of TMT bar @ 100 mm CIC, both way, lifting arrangement complete including all necessary earth work etc complete all as specified and directed by Engineer-in-Charge

Supply and fix exhaust fan,steel body AC Single phase,230 V of size 300 m sweep with ,blades and frame and louvers heavy duty etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement energy saving and environmental friendly long life LED street light 25 Watt (Bldg security light) made up of pressure die cast aluminium housing with mild power LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 fixed on wall with GI pipe of suitable dia and all fixing accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V , 50 HZ etc complete all as specified and directed by Engineer-in-Charge Make -Havell's Cat Part: (ENDURAPEARLSL25W MP) ENDURAPEARLSL25WLED757SASYTOPCMP or equivalent makes mentioned in list of makes in Appendix `C'

M & L for Supply,laying ,connecting ,testing and commissioning and jointing , LT underground cable in replacement ,1100 volts grade, XLPE insulated, armored with galvanized round steel wire or steel strip, electric power cables heavy duty, with multi stranded aluminum conductor, laid in ducts, fixed on poles/walls with proper size saddles and clamp complete all as specified and as directed by the Engineer-in-Charge of following Sizes :- Make:Havells/Polycab/gloster

(a) LT cable10 Sqmm, 2 core.

Supply & lay HDPE pipe 40 mm bore for laying of LT cable complete with all accessores etc complete all as specified and directed by Engineer-in-Charge

Supply and fix GI pipes, medium grade including necessary fittings such as sockets, elbows, tees, reducers, unions, nipples etc laid in trenches / walls / floors etc for the 50 bore pipe complete all a s specified and as directed.

All as per serial item No 78 (here-in-before) but 25mm bore pipe

Material and labour in repairs gun metal gate valve/brass stop valve, high pressure both ends screwed down with crunch or butterfly handle with suitable size sockets on both ends nipples, unions, etc suitable for up to 50 mm bore GI pipe etc complete all as specified and as directed by Engineer-in-charge

All as per serial item No 80 (here-in-before) but 25 mm bore pipe

S& F in repairs high pressure polythelene float valve with PVC ball suitale for fixing to GI pipe of 25 mm dia etc complete all as specified and direcrted by Engineer-in-Charge