ADDN/ ALTN/RENOVATION TO BLDG NO P-68, P-80, P-81 AND P-82 AT MT SEC AT NDA KHADAKWASLA

Amount

Demolition of brick work or stone/boulder masonry built in cement mortar including all quions /archers etc and removing debris from site to outside MoD land complete all as directed.

M&L for precast cement concrete (1:3:6) type C-1 ( using 20mm size graded stone aggregates ) block masonry with solid blocks exc10 cm thick in width and setting in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints,hacking for key ,scrubbing down with water etc complete all as specified and directed

M&L for 15 mm thick cement plaster on brick or concrete surface in cement mortar1:6 included finishing surface even and smooth without using extra cement on walls etc complete all as specified and directed

M&L for 10mm thick cement plaster on concrete surface in cement mortar (1:3) included finishing surface even and smooth without using extra cement on ceiling etc complete all as specified and directed

Material and labour for plastering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra lime or cement using WPC complete all as specified and directed Note: WPC shall be measured and paid separately.

Supply only water proofing compound as per relevant IS complete all as specified & directed

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over one coat of alkali registant priming paint etc complete all as specified and directed.

Ditto all as per item No 8 above here-in-before but in ceiling etc complete all as specified and directed.

M&L preparation of newly plastered surfaces of wall and applying two coats of cement base paint white or tinted including scaffolding arrangement, trestles, ladders etc complete all as specified and directed.

Dismantling CGI corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof coverings, complete all as specified and directed

S&F rolled mild steel in Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-410 (Gde E- 250 ) quality-A complete all as specified and directed

S&F mild steel screw or bolts (machine made) with hexoganal or square heads at one and screwed the other, or screwed both ends each screwed end to be filled with washers and hexogonal or square nut ,not exceeding 5cm long and diameter of neck 5 to 10mm complete all as specified and directed.

S&F 0.5mm Pre-painted galvatume aluminium Zinc coating steel GI based corrugated sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self taping screws complete all as specified and directed

M & L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces incl preparation complete all as specified and directed

Taking down of existing tarfelt of any description and thickness on roof top including flashing and junction of parapet and cleaning existing roof top surface by brooming , wire brushing incl removing the debrish out complete all as specified and directed

Demolition Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

M&L for cement concrete type B0 (1:2:4) (using 12.5mm size graded stone aggregate ) in roof padding, mud stops, rounded or chamfered edges complete all as specified and directed

M&L for 10mm thick rendering on concrete surface on roof in cement plaster 1:3 finished even and fair without using extra cement by using liquid WPC @ 200ml of 50kg of cement complete all as specified and directed Note: Liquid Water proofing Compound measured and paid seprately

Supply only liquid water proofing compound all as directed

M&L for water proofing treatment on wall,roof,chajja's,gabble walls, edges (at any respective height of bldg ) as following as manufacturer's instructions complete all as specified all as specified and directed (a) preparing plastered surfaces and applying approved bituminous primer @ 0.3 Kg/sqm uniformly to receive APP membrane (b) Applying and stick non-woven polyster matt modified APP Membrane 3mm thick as reinforcement weighing not less than 3.5 Kg/sqm by torch application and side overlap of 150 mm and over lap of 150 mm longtitudinally, (c)At the junction of roof and parapet wall a groove of 75mm wide and 65mm deep and shaping horizontal of groov with 1:3 with bituminious mastic joints/overlap shall be sealed with hot bitumen 85/25 (d)Applying one coat of aluminium paint on top of the membrane (at any height ) as per manufacturer instructions

Taking down chowkhats or frame not exc 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed

Taking down chowkhats or frame exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames) complete all as specified and as directed

S&F aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed

S&F anodised powder coated ventilators with louvers with partially guaged shutter using 5 mm thick x 10 cm wide frosted glass strips with rubber beading and glazing clips etc using aluminium sections weighing not less than 0.55 Kg/M complete all as specified and as directed

Supply and fixing Powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodisedaluminium snap beading, screws etc.including fixing of 5 mm thick Sheet glass, complete all as specified. Fixing included the making good of the opening, such as plastering jambs, levelling and finishing complete all as specified and as directed

S&F anodised aluminium powder coated door shutter, aluminium section wt 0.55 Kg/m including neccesary joining cleats, glazing clips,rubber neoprene packing, handle 2 nos in each door, hinges, anodised aluminium snap beading screw etc ,complete all as specified and directed

S&F aluminium powder coated three track sliding window with mosquito net two track for glass leaf sliding and one track for mesh leaf sliding outer frame weighing 0.699 Kg/m,75x26 mm size equvalent Jindal model 20671, shutter plain of size 37.5x15mm weighing 0.366 Kg/m, Section No 20690 Jindal), with powder coating of min thickness 50 micron with one or more rebates, sliding type without sash bars, 5mm thickness double tampered clear glass , rubber packing, snap beading screws,with horizontal sliding type with stainless steel mesh, frame, powder coated aluminium grill type AL 925 or equvalent grill, cutting in suitable size and fitting with screws and suitable beedings to aluminum window frame complete etc. complete all as specified and as directed

S&F Door closer hydraulically regulated,designation No. 2,universal type, aluminium (Die cast) body suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed etc. complete all as specified and as directed

M&L 20(+ -2mm) thick Granite (of jet black ) work (table rubbed and polished ) in steps ,jambs ,pillars,window cills, cooking plateforms and like in over 20mm thick cement mortar 1:6 for screed bed including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified. Exposed edges to make half round complete all as specified and as directed.

M&L Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc.complete all as specified and as directed

M&L Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and incl 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed

Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including cleaning off premises where directed complete all as specified and as directed

M & L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75 mm thick, finished even and smooth without using extra cement, including making joints 12 mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen85/25 and sand in the proportion of (1:3 ) by weight complete all as specified and as directed

Dismantling floor or wall tiling of any description and size including cement mortar bedding (but not backing), removing rubbish off the premises com[plete all as directed.

Dismantling of Stone slabs of any description or thickness in floors, aprons etc including cleaning off premises where directed.

M&L for coloured glazed ceramic tiles of size 450x300x7 mm thick as in vertical surface set and jointed in neat cement slurry and pointed flush in white cement with pigment over and including 10mm thick baking coat of CM 1:3 complete all as specified and as directed

Material and Labour for Joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but n exc 0.18 Sqm, (400x400x7 to mm thick), in flooring etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and over and incl 15mm thick screed bed or bedding layer in CM (1:4) complete all as specified and as directed

M&L for Virified Ceramic tiles light shed 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and over and including 20mm thick screed bed or bedding layer in CM 1:6 complete all as specified & directed.

M&L for 25 mm thick cement concrete type B-1, (1:2:4) (20 mm graded stone aggregate) as in sub base of tiles complete all as specified and directed.

M & L 75mm thick cement concrete type D2, 1:4:8 (Using 40mm graded stone aggregate) as in sub base including use of necessary form work etc complete all as specified and directed.

M&L for machine cut superior quality Kota stone slab flooring 20-25 mm thick over cement screed , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete match including bulnosed to edges complete and incl 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed

M & L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed, incl 10mm thick rendering in CM (1:4) on vertical surface for receiving complete all as specified and directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed .

Supply and fixed rotational moulded polyetylene triple layered water storage tanks (cylindrical vertical with closed top) of 500 Litres capacity hoisted and fixed in position and connecting up pipes and ball valve complete set of PTMT, securing access covers all as specified and directed

Supply and Fix 20mm bore PVC brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and as directed

S&F 15 mm bore mild steel water tubing medium grade galvanized with all fittings and fixture fixed to walls ceiling or laid in floors complete all as specified and as directed

All as per above item No 49 above here-in-before but for 20 mm bore

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth etc. complete all as specified and as directed

S&F gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed of 20mm dia on stone, concrete, block, slab or wall in repairs of ISI marked complete all as specified and as directed

M&L PVC (SWR) floor trap with steel grating 75mm dia including jointing to waste pipe including removing old traps complete all as specified and as directed

M/L 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or laid in floors complete all as specified and as directed

M/L 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or laid in floors complete all as specified and as directed

S&F PVC (SWR) bends 110 mm bore complete all as specified and as directed

S&F PVC (SWR) bends 75mm bore complete all as specified and as directed

S&F for 110mm dia PVC (SWR) branch piece single(single Y) equal or unequal with access door complete all as specified and directed

S&F for 110mm dia PVC (SWR) vent cowl complete all as specified and directed

S&F Vitreous china wash down water closet (Pedestal pattern) with P or S trap , white in colour including fixing bolts, connection to drain and to flushing pipe with low level PVC valve less symphonic action type flushing cistern of 10ltrs capacity white in colour with inlet, ball valve float and PVC flush pipe 32mm dia with white seat cover, closed pattern with flat bottom and cover and mild steel chromium plated or hinging device complete all as specified and as directed

S&F health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and as directed

S&F 15 mm bore Bib taps, cast copper alloy with crutch or butterfly handle,fancy type, long body screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F PVC connection 75cm long 15mm dia, with 2 Nos CP brass check nuts complete all as specified and as directed

Supply & Fix 15 mm two in one angle valve chromium plated with wall flange and fancy type with high pressure screwed down and with CP flange of same make complete all as specified and directed

Supply and Fixing wash hand basins vitreous china flat back 450mmx300mm size white, first quality, with and including chromium plated waste grating 32mm size, PVC waste pipe 25mm bore heavy duty China and plug and porcelain stopper, brackets of Mild Steel angle iron (35mmx35mmx5mm) of suitable size including two coat of synthetic enamel paint over a coat of primer over angle iron brackets complete to walls all specified and as directed.

S&F Towel rail 600 mm long of CP brass, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F for Stop valves 15mm dia, chromium plated ,fancy type, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and directed .

S&F for Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed , screwed for iron pipe of bore 15 mm fixed complete all as specified and as directed.

S&F Soap dish any type fixed to plugs with chromium plated brass screws minimum size 160x160x90mm complete all as specified and as directed

M&L Road cutting and repair to disturbed road with PCC (1:2:4) type B2 100mm thick over 150mm hard core of broken stone of gauge n exc 63mm over rammed earth etc complete all incl cutting of road portion complete all as specified and as directed

Removing demolished materials etc (other than spoil) to a distance exc 1.00 KM not exc 5 Km incl loading, unloading and stacking etc., complete all as specified and as directed

M & L for 100 mm thick cement concrete 1:2:4 type B-1 using 20 mm graded aggregate as in floor etc complete all as specified and as directed

M&L for Hardcore gauge n.exc 63mm of broken stone or boulders deposited, spread and levelled in layers n exc. 15 cm thick,, watered and well rammed to a true surface complete all as specified and as directed

M&L for moorum or red bajari (spread thickness 50mm thick) spread and compact complete all as specifed and directed.

M & L for Cement concrete work in pavement/hard-standing of flexural strength 40kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all as specified and directed .

M & L for PCC 1:2:4 type B1(using 20 mm graded aggregate) in surface channels and drain compete complete all as specified and as directed

M & L for PCC 1:2:4 type B1 using 20m graded stone aggregate in coping including weathering slightly rounded or chamfered angles and throating includin use of necessary form work and finishing exposed surfaces of concrete even andsmooth without using extra cement complete all as specified and directed.

M & L for providing precast RCC 1:2:4 type B1 (using 20mm grade stone aggregate as in cover slabs for drain set in CM (1:6) all as complete all as specified and as directed Note : Reinforcement shall be measured & paid separately

S & F for providing mild steel TMT bars 6 to 8 mm dia cut to length bent to shape required includig cranking, bending etc & binding with ms wires (annealed) n. exe 0.9mm dia complete all as specified and as directed

M& L RCC (Nominal mix) type B1, 1:2:4 (using 20 mm graded stone aggregate) for Foundations, including rafts, footings, plinth beams, bases for columns, etc. complete all as specified and as directed

M & L Formwork to Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed

M & L for Mild steel 10mm dia and over TMT bars as in reinforcement cut to length bent to shape required including cranking, hooking at ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed

All as per item No 82 above here-in-before but in 5 mm dia and over upto and including 10 mm dia in stirrups and binders etc complete in all as specified and directed

M &L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide,filled with sealing compound.grade A complete in all as specified and directed.

Raking out joints/pointing to squared rubble masonry, coursed or uncoursed built in cement mortar complete in all as specified and directed

M&L for flush pointing to random or polygonal rubble, uncoursed on brought upto courses in cement mortar (1:4) complete in all as specified and directed

Excavation in trenches, n.exc 1.5M wide and not exceeding 1.5M depth for foundation etc or for shaft, wells, cesspits, manhole, pier holes etc n.exc 10 Sqm on plan and n.exc 1.5M in depth and getting out Hard/dense soil complete in all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm complete all as specified and directed

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed complete in all as specified and directed

M&L for brick work with sub class 'B' bricks, straight or curved on plan, exc 6M mean radius, built in CM 1:4 complete all as specified and directed

M&L for plain cement concrete 1:3:6 type C-2, using 40mm graded stone aggregate as in foundation and bed concretes, mass concrete etc complete all as specified and directed

Extra for forming for finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds mitred stopped etc all as specified and directed

Supplying and laying 150mm bore Reinforced Cement Concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed

M&L for PCC 1:3:6, type C-2, using 40mm graded stone aggregate as concrete bed to drain pipes of 150mm bore including packing under and haunching against the sides of pipes, after they are laid and tested complete all as specified and directed

Cutting into existing manholes for connecting new drains of dia 150 mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed

Taking up or down 50 mm bore GI water tubing and connections of pipe and fittings and removing unserviceable pipes and fittings from site complete all as directed.

Supply and laying in of trenches / on ground GI tubing 'Medium grade' of 50 mm bore with all fittings like Tee,socket,elbow etc complete including taking down of old rusted pipe complete all as specified and directed Note : excavation of earth work shall be measured and paid seperately.

S&F in replacement of Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 50mm dia all as specified and directed.

M & L for replacement of Cast iron Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs of size 100x100x50mm dia complete all as specified and directed

M & L for repairing to damaged portion of valve pit chamber on exisiting chamber foundation with 230 mm thick brick wall in CM (1:6) 75 mm thick coping with PCC 1:2:4 type B1, 15 mm thick plaster work in CM 1:4 over all internal and external wall with white wash of both surface and Chequered plate cover of 7mm thickness for Valve Pit Chamber of size upto 900x900x750 mm with hinges, equal angle iron frame(40x40x4mm) and necessary locking arrangement painting of synthetic Enamel paint over coat of red oxide primer on Plate including dismantling existing damaged portion of chamber and removal of all debris complete all as specified and directed .

M&L for cutting existing bituminous /concrete road/plinth protection upto 0.5 Mtr depth and width not exc 30cm for laying of pipe line/cable of any size, refilling and making good after laying of pipe with removed soil/dabries/dust and finally sealed with patchmat of thickness not less than to match with the top surface of Road complete all as specified and directed. Note : Rate for patchmate shall be deemed to be included in above qouted rate.

Taking down exiting copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

M&L for concealed point wiring in and including new PVC conduit medium grade with the help of multi-stranded unsheathed FRLSH copper cable 1.5 sqmm 650/1100V conforming IS:3419 -1988 adhereing to colour code including earth wire of the size 1.5 Sqmm green colored with modular steel or cast iron terminal boxes and modular cover plates as required at site including making good the distrubed surfaces and matching it with existing surface for the following :- (a) One light/Fan point controlled by one way switch 6 Amps 240 volts

(b) One 3 pin socket outlet, 5/6 Amps on the same board with other switches

(c) One 3 pin socket outlet, 5/6 Amps, independent

(d) M&L concealed point wiring with 4 sq mm copper conductor FRLSH (multistrand) PVC insulated ISI marked unseathed cable in and including PVC conduit not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 4 sq mm copper conductor as earth wire to common earth dolly complete all as specified and directed

S&F modular switch 1 way 10 A 1 module all as specified and directed .

S&F Modular socket 6 A 2/3 Pin 2 module all as specified and directed

S&F modular switch 1 way 16 A 1 with indicator module all as specified and directed

S&F Modular socket 6 A/16A 2/3 Pin 2 module aall as specified and directed

S&F modular BLDC fan regulator, 2 module, suitable for ceiling fan of 1200/1400mm sweep all complete all as specified and directed.

S&F in replacement for ceiling rose, 3 terminals /PVC/Polycarbonate, isolated body complete all as specified and directed

Taking down ceiling fan/Exhaust Fan, sealing cable end,dismantling blades and removing fan and blades to MES E/M store complete all as specified and directed

Supply and fixing ceiling fan complete with blades, down rods and other accessories, 230 V, 1200 mm sweep with Minimum air delivery of 210 CMM BEE Five star rated with brushless direct current motor (BLDC), white/Ivory in colour all as specified and directed.

S&F of high speed wall mounted fan with BLDC Motor fan of sweep 400 mm,,Full copper motor,auto thermal overload protection,compact style and powder coated gurads & pull cord switch for speed regulation and oscillation control including connectng up the power cord to the socket and necessary fixing accessories all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50Hz RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

S&F in replacement of 20watt,230V surface and wall mounted LED batten, extruded aluminium housing with polycarbonate diffuser and integrated electronic driver including connecting up with twin core twisted flexible copper condctor cable from ceiling rose all as specified. Make- Luker LT20PR 3 in 1 or equivalent make as mentined at list of makes in PS

S&F in repalcement surface mounted 2' x 2' LED Panel lights 35/36 W LED 6500K, 240Volts and glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully all as specified and directed. Note: The quoted price shall include the cost of Light and its driver.

S&F in replacement LED building security Sensor light fiitting 24 W, IP-65 protection made up of die cast alluminium housing with high power LED as lighting source and lens embeded PC cover having seperate driver compartment complete fixing with GI bracket made out of suitable GI pipe light grade suitable length bend to shape and fixed to pole/wall with necessary MS clamp accessories complete all as specified and directed Make- Luker LST-24SEN or equivalent make as mentined at list of makes in PS

Dismantling and refixing the ceiling fan/Exhaust Fan complete of any type and size , cleaning, servicing, painting greasing to bearings checking of nuts bolts , safety split pin, bushes , capacitor and complete spray painting complete all as specified and directed Note :- Expendable stores like cotton waste/cleaning materials, grease, lubricants, machine screws, safety split pin, bots/nuts and transportation to and from site to work place are deemed to be included in rate quoted.

M&L for Cutting chases for concealed conduit wiring, pinning in and making good to surface where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., cutting not exc 10 cm girth including 3 mm thick wall care putty on wall, making surface matching to adjacent surface complete all as specified and directed

Taking down exiting copper/aluminium sub main wiring complete for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

M&L for concealed sub main wiring with two single core PVC insulated FRLSH cables with stranded copper conductors 2.5 Sqmm , 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 2.5 sqmm continuous earth wire complete all as specified and directed Note: Two runs of 2.5 Sqmm cable with 01run of 2.5 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

M&L for concealed sub main wiring with two single core PVC insulated FRLSH cables with stranded copper conductors 4 Sqmm , 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 4 sqmm continuous earth wire complete all as specified and directed . Note: Two runs of 04 Sqmm cable with 01run of 4 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

M&L for concealed sub main wiring with Four single core PVC insulated FRLSH cables with stranded copper conductors 6 Sqmm , 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 6 sqmm continuous earth wire complete all as specified and directed . Note: Four runs of 06 Sqmm cable with 01run of 6 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

S&F in replacement of Fully Automatic Star-Delta Starter (ASD) - HGS Series, factory assembled in powder coated sheet steel enclosure, comprising of 40 Amps 3 Pole MCB, power contactor and 230V digital time switch for controlling air curtain , including earth work for fixing Timer switch distribution Board and shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 0.6 mt height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement all as specified and directed

S&F MCB DB 04 way SPN single door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and existing circuits complete all as specified and directed

Supply and fixing factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB) MCCB as In comer, with metal door (IP-43 protection) fabricated from CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified and directed. Note:MCBs/ MCCBs will be measured and paid seperately under respective Sch A item in the schedule

S&F MCB Isolater FP 40 Amps 415V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing.all as specified and directed

S&F MCB Isolater TP 63 Amps 415V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing all as specified and directed.

S&F in replacement of MCCB with rating of 125 Amps, 415 Volts 4 pole with 16 kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu). MCCB should be with suitable spreaders and phase barriers for each terminals complete all as specified and directed

Supply and fix in replacement sheet metal enclosures single pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessaries etc all as specified and directed . Make: Legrand Cat part: 5078 10 or equivalent make as mentined at list of makes in PS

S&F in replacement MCB DB 8 way SPN Double door sheet metal enclosure factory made suitable for MCB DB's 240 volts,concealed in wall complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site complete all as specified and directed . Make: Havells/Legrand.Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F in replacement MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing complete all as specified and directed.

Supply and fix in replacement of C Curve MCB SPN 40 -63 Amps working on 240 volts, 50 HZ,10 KA all as specified and directed .

Earthing complete with galvanised iron earth plate electrode 600 x 600 x 6mm as earthing lead buried directly in ground vertically to depth not less than 2.25 mtr below GL with the top edge of the plate not less than 1.5 mtr from GL, connected to GI earth lead of 4.0mm dia, by means of bolts & nuts, to GI and connected to earthing test point all as shown in elecrical plate No. 3 of SSR Part-I of 2009* specified or indicated and testing on completion including excavation / earth work in any type of starta, PCC (1:3:6) type C1 earthing chamber pre cast slab 50 mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric (XPM) weight not less than 4 KG/sqm cast iron frame, funnel with wire mesh GI watering pipe of 20 mm bore medium grade and lugs with and including GI earth wire 4 mm dia with GI protection pipe of 15 mm medium grade 7.5 meter long etc complete tested on completion all as specified and directed. Note: 1. Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre, PCC pit, funnel and RCC cover plate. 2. GI wire above 7.5m will be measured and paid seperately.

Bharekar Construction (BID ID -3364427)

Sarkar Enterprises (BID ID -3362735)

Mehta and Co. (BID ID -3363954)

SUN Enterprises (BID ID -3364631)

S G Enterprises (BID ID -3363467)

DARSHAN ENTERPRISES (BID ID -3364029)

Tejas Enterprises (BID ID -3364405)

M/S P D TUPE (BID ID -3364765)

Sunil Constructions (BID ID -3364264)