WELCOME MAINT TO CERTAIN MD ACCN AND INTERNAL ELECTRIFICATION WKS UNDER AGE B/R-I OF GE JHANSI

Amount

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.

All as per item No 01 above but not exc 1.5 sqm each

Taking down shutters of any description not exc 01 Sqm each, complete all as specified and directed.

Taking down shutters of any description exceeding 1.0 Sqm and not exc 2.0 Sqm each, complete all as specified and directed.

S&F of 25mm thick flush shutter for cup board door / shelves solid core construction with block board core and prelamination one face with decorative face veneer with lipping/frame to match and other side prelamination with balancing white, with and incl min 5 mm thick wooden beading fixed all around, complete all as specified and directed.

S&F 18mm thick prelaminated MDF board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in any situation as in cup board shelves/shutter or similar work, complete all as specified and directed.

S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm, complete all as specified and directed

S&F factory made solid PVC moulded door shutter 28 to 30mm thick (Stiles) with 2, 4 or 6 raised panel design with 2mm thick Wooden texture moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing, complete all as specified and directed. Make : Rajshree / Sintex / Greenlam

S&F of Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood grain printed PVC sheet and matching edges, reinforced with MS square tube, as specified in SSR Part-II 2010 (Section 8, on Page No - 175), complete all as directed. Make : Rajshree / Sintex / Greenlam.

S&F 100mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.

S&F 75mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.

S&F for 100 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21 anodized complete all specified and directed

S&F SS sliding door bolts,300mm long plate type, Matt Finish, with SS bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S&F aluminium alloy anodized sliding door bolt 250mm length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all specified and directed. (Make : Ashish, Classic)

S&F 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed. (Make : Ashish, Classic)

S&F 100mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed. (Make : Ashish, Classic)

S&F for 150mm aluminum handle cast type anodized complete all specified and directed. (Make : Ashish, Classic)

S&F for 100mm aluminum handle cast type anodized complete all specified and directed. (Make : Ashish, Classic)

S&F meld steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed

S&F for Door stopper 140 mm of aluminium alloy body anodised with tongue of rubber bush at one end fixed to door, complete all as specified and directed.

M&L for stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed.

M&L for stainless steel rod 15mm dia steel pipe for cupboard, cutting into length as required at site with and incl SS mounting brackets, complete all as specified and directed.

M&L for box type steel window with 80x40x1.25 m MS tubular frame with side hung shutters ( double shutter for glass and gauze) without sash bars jointed together with and incl grill using 12 mm square bar @ 10 cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars doweled and welded complete all as specified as directed. Note:- (a) The Glass / gauze shell be measured and paid separately. (b) Side hung Z-Section shutter shall be of size 20mm x 20mm x25mm and 3.0mm thick.

M&L for box type steel ventilator with 80x40x1.25mm MS tubular frame partly gauged with top hung shutter with and incl grill using 12mm square bars @ 10Cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars dovetailed and welded complete all as specified as directed. Note:- (a) The Glass / gauze shell be measured and paid separately. (b) Top hung Z-Section shutter shall be of size 20mm x 20mm x25mm and 3.0mm thick.

M&L for second class hard wood. Plain, solid, straight chowkhats and frame, wrought framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixing, complete all as specified and directed.

S&F 105x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F 125x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

M&L for mild steel angles, bars, flats etc, as in supports for hold fasts, pipe clamps, plain angle cleats for securing purlins, door frame, stay clamps incl nut & bolts (as required) and similar small articles confirming to Fe-290 Gde E-165, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in bed block for hold fast & filling in pressed steel door frame, cills, pre-cast lintel not exc 1.5mtr, coping, benching, complete all as specified and directed.

S&F of 35mm thick factory made modular designer flush doors, solid core construction, with block board core and prelamination on both sides, complete all as specified and directed. Make : Rajshree / Sintex / Greenlam

M&L for factory made, kiln seasoned, chemically pressure treated, 30 mm thick Second class hard wood glazed & skeleton shutter for doors, open rebated & prepared to receive glass, gauge etc (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section–8, clause 8.24(a) and conforming to IS-1003 Part-I & II, complete all as specified and directed. Make : M/S MP Wood Product (Indore) or equivalent mentioned in PS.

M&L for factory made, kiln seasoned, chemically pressure treated, 35 mm thick Second class hard wood glazed & skeleton shutter for doors, open rebated & prepared to receive glass, gauge etc (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section–8, clause 8.24(a) and conforming to IS-1003 Part-I & II, complete all as specified and directed. Make : M/S MP Wood Product (Indore) or equivalent mentioned in PS.

M&L for factory made, kiln seasoned, chemically pressure treated, 30 mm thick Second class hard wood glazed & skeleton shutter for window & ventilators, (fully glazed), minimum two panels divided into squares (without sash bars) and prepared to receive glass, gauge etc (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section–8, clause 8.24(a) and conforming to IS-1003 Part-I & II, complete all as specified and directed. Make : M/S MP Wood Product (Indore) or equivalent mentioned in PS.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as directed.

S&F of 3 mm thick sheet figured glass pin headed type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, complete all as directed.

S&F of 3 mm thick sheet glass ordinary quality and glazing type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, complete all as directed.

S&F in replacement of stainless steel wire cloth 0.36 mm in nominal dia of wire average width of aperture 1.40 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.

Taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern, complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall with FI clamps, complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall with FI clamps, complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC nahani / floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.

S&F PVC Gully trap of 125/110 mm outlet, jointing to waste pipe with cement solvent, complete all as specified and directed.

Taking down steel tubing with and incl connections, of 15 mm dia bore, complete all specified and directed.

Taking down steel tubing with and incl connections, of 20 mm dia bore, complete all specified and directed.

M&L for medium grade galvanised steel water tubing with and incl all fittings and fixtures, fixed to wall or laid in floors for 15 mm bore, concealed or exposed, complete all as specified and directed. Make : Jindal / Prakash Surya/ Tata

M&L for medium grade galvanised steel water tubing with and incl all fittings and fixtures, fixed to wall or laid in floors for 20 mm bore, concealed or exposed, complete all as specified and directed. Make : Jindal / Prakash Surya/ Tata

M&L for cutting chases, pinning in for concealed water tubing, not exc 10 cm girth and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc, complete all as specified and directed.

S&F in replacement of Vitreous China wash basin, white colour, flat back, size 550x400mm with and including fixing brackets, 32mm dia SS waste coupling, 32 mm PVC Waste pipe 800mm long, complete all as specified and directed. Make : Cera (Ist Quality)/ Parry ware (super fine)/ Hindware (Ist Quality)/ Prayag (Ist Quality).

M&L for 1st quality vitreous china ware European type WC with "P" or "S" type traps and same make plastic seat cover of white colour including flush pipe, fixing bolts etc and making good of the wall & floor surface, complete all as directed. Make : Hindware / Cera / Jaquar / Parryware.

S&F in replacement of Vitreous China Squatting pan, 'Orissa' pattern, size 580 x 440 mm, white colour with integral foot rests exluding flushing cistern & flush pipe, duly fixed in cement concrete bedding and making good of floor surface, complete all as specified and directed. Make : Cera (Ist Quality)/ Parry ware (super fine)/ Hindware(Ist Quality)/ Prayag (Ist Quality).

S&F in replacement of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white colour, dual flush type, ISI marked with and incl inlet ball valve, float and handle etc with and including wall bracket, 450mm long PTMT PVC connection, 32 mm dia PVC flush pipe, duly connected to squat pattern / pedestal pattern water closet, , complete all as specified and directed. Make: Hindware / Cera / Parryware / Prayag

S&F in replacement of SS sink with approx bowl size of 500 x 400 x 200 mm, made of 1.0 mm thick SS sheet (SS-304), ISI marked, with and incl cantilever brackets etc, duly bedding in cement mortar to dwarf wall, complete all as specified and directed. Make : Nirali / Prayag / Cera / Parryware

S&F in replacement of bib cock, 15 mm dia with wall flange, fancy type, made of cast copper alloy, chromium plated, screwed down, screwed for iron pipe or for brass ferrule, ISI marked, complete all as specified and directed. Make : Hindware / Cera / Parryware / Prayag

S&F in replacement of bib cock, 15 mm dia, long body type with wall flange, fancy type, made of cast copper alloy, chromium plated, screwed down, screwed for iron pipe or for brass ferrule, ISI marked, complete all as specified and directed. Make : Hindware / Cera / Parryware / Prayag

S&F in replacement of angular stop cock 15 mm dia with wall flange, fancy type, made of cast copper alloy, chromium plated, screwed down, screwed for iron pipe or for brass ferrule, ISI marked, complete all as specified and directed. Make : Hindware / Cera / Parryware /Prayag

S&F in replacement of 2-in-1 wall mixer with provision for overhead Shower with 115mm long bend pipe on upperside, connecting legs & wall flanges, made of cast copper alloy, chromium plated fancy type, complete all as directed. Make : Hindware/ Cera/ Parryware / Prayag.

S&F in replacement of swan neck sink/basin mixer, 15 mm dia with flange made of cast copper alloy, chromium plated, complete all as directed. Make: Hindware/ Cera/ Prayag / Parryware.

S&F in replacement of wash basin mixer, pillar tap with out popup waste system made of cast copper alloy, chromium plated fancy type, suitable for 15 mm dia bore pipe, complete all as directed. Make : Hindware / Cera / Parryware.

S&F in replacement of overhead shower of dia 125 mm round shape single flow, ABS body, chrome plated fancy type, with and incl swivel type shower arm and wall flange, made of cast copper alloy, chromium plated, fancy type, complete all specified and directed. Make : Hindware/ Cera/ Parryware / Prayag

S&F in replacement of handshower (health faucet) with 8 mm dia, 1.0 mtr long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all as directed. Make : Hindware/ Cera/ Parryware / Prayag / Pearl.

S&F in replacement of SS grating of square/round shape, overall size of 125 mm with and incl fixing with CM to floor/nahani traps etc, complete all specified and directed. Make : Hindware / Cera / Parryware / Prayag.

S&F in replacement of bottle trap 32 mm size with 250 mm long wall connection pipe and wall flange made of cast copper alloy, chromium plated fancy type, complete all as directed. Make : Hindware/ Cera/ Parryware / Prayag.

S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all specified and directed. Make : Hindware / Cera / Parryware / Prayag.

S&F in replacement of Brass CP connection, 15mm dia and 450mm long with 2 Nos brass check nuts and washers, suitable for hot water connection, complete all specified and directed. Make : Hindware/ Cera/ Parryware / Prayag

S&F in replacement of PVC waste pipe 32 to 40 mm dia 750 mm long with for wash hand basin or kitchen sink, complete all as specified and directed.

S&F in replacement of waste coupling, chromium plated (half or full threaded), 32 mm dia size, complete all as directed. Make : Hindware/ Cera/ Parryware / Prayag / Pearl.

S&F in replacement of waste coupling, chromium plated (half or full threaded), 40 mm dia size, complete all as directed. Make : Hindware/ Cera/ Parryware / Prayag / Pearl.

S&F in replacement of plastic seat covers for water closet, of existing colour, closed pattern with flat bottom with chromium plated hinging device, complete all as directed. Make: Hindware / Cera / Pearl / Parryware / Prayag

S&F in replacement of towel rail 600 mm long with wall bracket, made of cast copper alloy, chromium plated, complete all specified and directed. Make : Hindware/ Cera/ Parryware / Prayag

Dismantling of water tank of 500 to 1000 ltr capacity of any description and removal, complete all as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for cleaning the tank with bleaching powdred, scrubber, repairs if required like nipple, washer ( rate included) etc. and re-fixing in same position of exc. 250 litres & not exc. 500 litres capacity of tanks, complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for cleaning the tank with bleaching powdred, scrubber, repairs if required like nipple, washer ( rate included) etc. and re-fixing in same position of exc. 500 litres & not exc. 1000 litres capacity of tanks, complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed. Make : Sintex / Vectus / Polycon

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed. Make : Sintex / Vectus / Polycon

S&F in replacement of 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F in replacement of 15 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as directed. Make : Prayag / Polytuff / Pearl

S&F in replacement of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as directed. Make : Prayag / Polytuff / Pearl

Demolition of brick work built in cement mortar or lime mortar including all quoins arches, pillars etc complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

Taking down cement plaster on brick or stone wall including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for 15mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces of wall, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) on other than fair faces of brick work or concrete surfaces of wall, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering in CM (1:3) on fair faces of concrete surfaces of ceiling, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coat of cement based paint over and incl one coat of exterior grade cement based primer, complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coats of oil bound distemper, over and incl a layer of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

M&L for preparation of new plastered surface of wall and applying 3 coat of white wash, complete all as specified and directed.

M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping, watering and applying two coats of oil bound distemper over and incl one layer of Birla/JK White wall care putty to get level and smooth surface on old plastered surface of internal wall, complete all as specified and as directed.

M&L for preparation of surface by washing, rubbing down and stopping of distempered and painted surfaces of walls and applying one coat of distemper oil bound white or any tinted complete all as specified and directed.

M&L for preparation of surface by washing, rubbing down and stopping of distempered and painted surfaces of walls and applying applying two coat of weather proof exterior grade emulsion paint, complete all as specified and directed.

M&L for preparation of surface by washing, rubbing down and stopping of distempered and painted surfaces of walls and applying one coat of white wash (lime) on walls surface, complete all as specified and directed.

M&L for preparation of surface by washing, rubbing down and stopping of distempered and painted surfaces of walls and applying one coat of white wash (lime) on ceiling surface, complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over and including a coat of red oxide, primer complete all as specified and directed.

Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over and including a coat of Pink primer, complete all as specified and directed.

Preparation of old painted steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint (Ordinary tint), complete all as specified and directed.

Preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint (Ordinary tint), complete all as specified and directed.

Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for semi-skid cermaic coloured tiles of size 300 X 300mm, 7 to 8mm thick, as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles colour, laid over and including 15 mm thick screed/ bedding layer in CM (1:6), complete all as specified and directed. Make - Kajaria / Nittco / Jhonson / Somany / Orient

M&L for Jointless vitrified tiles of size 600 x 600mm, 9 to 10mm thick, as in flooring etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles colour, laid over and including 15 mm thick screed/ bedding layer in CM (1:6), complete all as specified and directed. Make - Kajaria / Nittco / Jhonson / Somany / Orient

All as per Srl item No 109, mentioned here-in-above, but in skirting with and including 10mm thick rendering in CM 1:4 on wall, complete all as specified and directed.

M&L for Coloured Glazed ceramic tiles of size 300 x 450mm, 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles colour with and including 10mm thick rendering in CM 1:4 on wall, complete all as specified and directed. Make - Kajaria / Nittco / Jhonson / Somany / Orient

M&L for 16 - 18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and including moulding, rubbing & polishing, and laid over and incl 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path, laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and as directed. Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.

Dismantling of wall and ceiling boards( fibre pulp insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillats, complete all as specified and directed.

S&F of false ceiling comprising of 12 mm thick Gypsum board including GI frame work for seamless ceiling made of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including two coats of plastic emulsion paint, complete all as directed. Make : India Gypsum / Gyproc / Lafarge.

M&L for making designer cornices of 75 mm x 75 mm by POP and applying two or more coats of plastic emulsion paint to match colour with gypsum board false ceiling /wall etc, complete all as directed.

Demolition of RCC not exceeding 15cm thickness in roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work, complete all as specified and directed.

M&L for RCC (nominal mix) Type A1 1:1.5:3 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc, complete all as specified and directed. (Note : The steel reinforcement shall be measured and paid separately).

M&L for RCC (nominal mix) Type A1 1:1.5:3 (using 20mm graded stone aggregate) as in chajjas, complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

All as per Srl item No 120, mentioned here-in-before but mild steel TMT bars of 5mm dia and over upto and incl 10mm dia as in stirrups, spacers and binders.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exc 200mm thick (Horizontal or sloping), complete all as specified and directed.

Use and waste of form work to soffits of chajjas and similar work including edges complete for rough finished surface, complete all as specified and directed.

M&L for demolition of cement concrete of any description and in any position of WC’s/Bathroom etc in sunken portion area, removing demolished material completely and old waste pipe from sunken portion and cleaning the side/bottom surface of sunken floor with wire brush, complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:3 on fair faces of brick work and concrete surfaces duly mixed with liquid WPC @ 150 ml in 50 Kg of cement by weight, on vertical and bottom surface of sunken portion, complete all as specified and directed. Note :- The WPC will be measured and paid separately.

M&L for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in padding, levelling etc and roof kerbs with liquid water proofing solution (mixed @ 150ml in 50 Kg of Cement by weight), finished even and fair with proper slope as prepatory works to water proofing treatment, complete all as specified and directed. (Note : Water proofing compound, as required, shall be measured & paid separately under respective item only)

M&L water proofing treatment to toilet area of sunken floor complete all as specified and directed by Engr in charge with following course of description below :- (a) Applying first layer of cement slurry @ 0.488Kg/Sqm mixed with acrylic based polymer modified cementation composite compound coating @ 0.253Kg/Sqm of make as approved in technical instruction 5/2003 and be allowed to air cure for 4 Hours (b) Second layer of cement slurry @ 0.242Kg/Sqm mixed with acrylic based polymer modified cementation composite compound coating @ 0.126Kg/Sqm and be allowed to air cure for 4 Hours (c) Followed with water curing and testing for leak proof by ponding test for 48 Hours

M&L for PCC 1:5:10 type E2 (40mm grade stone aggregate) as in mass concrete, filling in two layers in sunken portion, complete all as specified and directed.

M&L for 50mm dia PVC pipe, medium grade, as in spout to drain out, in sunken portion, complete all as specified and directed.

Supply only integral liquid water proofing compound, mixed in CM as per manufacturer instruction, complete all as directed. Make : Dr Fixit LW + Professional or equivalent of Fosroc / Sika

M&L for kitchen cabinets, wall hanging type, made of 18 to 20 mm thick PVC solid sheet with one side of wooden texture decorative surface, including necessary cutting of sheet in to size joining with screwes and adhesive fixing to wall with screws, with and including necessary fitting like self closing type hydraulic hinges, SS handle, PVC bidding tape, kitchen cabinets consists of No of cabins having depth of 350mm of required size, All cabins having door(s) with one or two leaf shutter of same materials, complete all as directed. Note : (i) The size of cabins will be decided accordingly to site dimension and requirement. (ii) The complete work will be carried out in line, level and proper finished manner and without any gap in joints. (iii) The area will be calculated from length and height and payment will be made accordingly). (iv) Make : Multiwood or equivalent make approved by GE.

M&L for Cutting/ Griding/ polishing on existing terrazzo flooring as per local trade practice, complete all as specified and directed

M&L for Cutting/ Griding/ polishing on existing terrazzo on vertical surface as per local trade practice complete all as specified and directed

Removing existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down cement concrete, existing plaster lime cova 80 to 100mm thick mud phuska/cement concrete/lime cova etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush, with and incl demolition of cement concrete tiles, complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) mixed with water proofing compound @ 0.20 Ltr/bags on roof surface when concrete is green, complete all as specified and directed. (Note : Water proofing compound, as required, shall be measured & paid separately under respective item only)

M&L water proofing treatment to roof slab with AAPP based modified polymeric membrane, seven layered (four layer under item No 136 and other three layer under item No 137 to 139) with centre core 100 micron HMHDPE, outer film 20 micron each, having thickness 3mm weight not less than 3kg/Sqm with 100mm overlap laid as per manuacturer's instructions, complete all as specified and as directed by Engineer-in-Charge with following course of description below:-

(a) 1st coat applying bitumen primer confirming to IS-3384-1965 @ 0.40 Kg/Sqm to be applied on prepared roof surface till the surface is properly impregnated

(b) 2nd coat of bonding material using blown type bitumen conforming to IS-702 of grade 85/25 @ 1.20 Kg/Sqm

(c) 3rd course ie. laying of APP Based modified membrane described herein before with 100mm overlap in longitudinal direction and 150mm in transverse direction, all joints and changes in all direction should be covered covered with cement mortar (1:3) mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane.

(d) Forth course of bounding materialusing blown grade bitumen 85/25 conforming to IS-702 @ 1.20 Kg Per Sqm and over spread course sand for making roughening the surface to receive the next layer treatment.

M&L for cutting grooves in brick wall, 75mm wide and 65 mm deep and shapping horizontal face of groove with cement mortar (1:3), complete all as specified and directed.

M&L for applying one coat of bituminious aluminium paint @ 0.20 Kg Per Sqm over APP membrane, complete all as specified and directed.

M&L for factory made plain cement concrete tiles with grey cement and no pigment, of size 20 cm x 20cm x 20 to 22 mm thick, set & jointed and pointed in neat cement slurry mixed with grey cement and pigments, laid over and including 15mm thick screed bed or bedding layer in CM 1:6 mixed with with water proofing compound @ 0.20 Ltr/bags, complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass/GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed by Engineer-in-Charge for the following points:- Make: Conduit-AKG/ Atul/ Kalinga/Modi/Precision, Wire - Havells/ Polycab/ Finolex / KEI

One light / ceiling fan / exhaust fan / call bell point controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per item No. 140.00 here-in-before but one 16A socket point controlled by one 16A switch on independent board with 2.5 sqmm wires.

M&L for sub main wiring along with earth wire with FRLS insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including taking down existing unserviceable sub main wiring of any description complete all as specified and directed by Engineer-in-Charge for the following sizes:- (Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length) Make: Conduit-AKG/ Atul/ Kalinga/Modi/Precision, Wire - Havells/ Polycab/ Finolex / KEI

2runs x 4 sqmm (Ph & N) + 1run x 4 sqmm (earth wire)

2runs x 6 sqmm (Ph & N) + 1run x 6 sqmm (earth wire)

Notes for item No. 140.00 to 142.02: (i) Quoted rate shall deemed to include the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & capping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing capping may be used in that portion.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials for taking credit and making good disturbed surfaces of walls, floors, etc with cement plaster, putty and paint to match with the existing surface complete all as specified and directed by Engineer-in-Charge.

Supply and fix switch piano flush type 6 Amps, one way, 240V, 50Hz complete all as specified and directed. Make: Havells(Reo) / Goldmedal/ SSK /GM

Supply and fix electronic fan regulator rotary type in 5 steps, 240V, 50Hz complete all as specified and directed. Make: Havells(Reo) / Goldmedal/ SSK /GM

Supply and fix bell push switch flush type 6 Amps, 240V, 50Hz complete all as specified and directed. Make: Havells(Reo) / Goldmedal/ SSK /GM

Supply and fix socket 6 Amps, 2-in-1 flush type universal 240V, 50Hz complete all as specified and directed. Make: Havells(Reo) / Goldmedal/ SSK /GM

Supply and fix ceiling rose 6 Amps, 3 plate, 240V, 50Hz complete all as specified and directed. Make: Havells(Reo) / Goldmedal/ SSK /GM

Supply and fix Lamp holder, angle type with metal ring, PVC/Polycarbonate body including supply and fix of 7 watt LED bulb complete all as specified and directed. Make: Lamp Holder :- Havells(Reo) / Goldmedal/ SSK /GM, LEB Bulb :- Philips / Havells / Wipro / Bajaj / Osram

Supply and fix switch piano flush type 16 Amps, one way, 240V, 50Hz complete all as specified and directed. Make: Havells(Reo) / Goldmedal/ SSK /GM

Supply and fix socket 16A & 6A, 2-in-1 flush type universal 240V, 50Hz complete all as specified and directed. Make: Havells(Reo) / Goldmedal/ SSK /GM

Supply and fix modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 25A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge. Make : Standard / Indo Asian / L&T / Havells

Supply and fix MCB distribution board, TPN, 4 way in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge. Note: MCBs shall be measured and paid separately. Make : Standard / Indo Asian / L&T / Havells

Supply and fix MCB distribution board, SPN, 12 way in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge. Note: MCBs shall be measured and paid separately. Make : Standard / Indo Asian / L&T / Havells

Supply and fix MCB 63A, 10 KA, TPN, 415 V, 50 Hz complete all as specified and directed by Engineer-in-Charge. Make : Standard / Indo Asian / L&T / Havells

Supply and fix MCB 40A, 10 KA, SPN, 'C' curve, 240 V, 50 Hz complete all as specified and directed by Engineer-in-Charge. Make : Standard / Indo Asian / L&T / Havells

Supply and fix MCB 6 - 32A, 10 KA, single Pole, 'C' curve, 240 V, 50 Hz complete all as specified and directed by Engineer-in-Charge. Make : Standard / Indo Asian / L&T / Havells

Taking down existing unserviceable DBs TPN / SPN of any description from the walls and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge.

Supply and fix call bell ding dong, AC, 240V, 50Hz complete all as specified and directed. Make: Havells(Reo) / Goldmedal/ SSK /GM

Supply and fix LED batten with CRCA sheet steel box type body pre-wired suitable for and including provision of 1x20/22 Watt (4 feet) retrofit LED tube with PC body, full white and connecting up with twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed by Engineer-in-Charge. Make: Philips / Havells / Wipro / Bajaj / Osram

Supply and fix integrated LED batten 9/10 watt, 2 feet long, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed by Engineer-in-Charge. Make: Philips / Havells / Wipro / Bajaj / Osram

Supply and fix LED bulkhead luminaire in die-cast aluminium alloy body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection suitable for and including provision of 10W retrofit LED bulb, full white with B22 lamp holder complete all as specified and directed by Engineer-in-Charge. Make: Philips / Havells / Wipro / Bajaj / Osram

M&L for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth wire up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Taking down ceiling fan of any size carefully, dismantling blades, cleaning the motor and blades with suitable cleaning agent and greasing / oiling the bearing and refixing the ceiling fan in its existing location and connecting up including provision of three core 0.5 sqmm PVC insulated flexible copper conductor cable (ISI marked) from ceiling rose to connector of fan and testing for satisfactory functioning complete all as specified and directed by Engineer-in-Charge.

Taking down exhaust fan of any size carefully, dismantling blades, removing all grease and oil deposited on the motor and blades and cleaning with suitable cleaning agent and greasing / oiling the bearing and refixing the exhaust fan in its existing location and connecting up including provision of three core 0.5 sqmm PVC insulated flexible copper conductor cable (ISI marked) from ceiling rose to connector of fan and testing for satisfactory functioning complete all as specified and directed by Engineer-in-Charge.

Taking down existing Geyser of capacity 25 Ltrs / 50 Ltrs carefully from its installed position and keeping in safe custody of contractor until the B/R work is completed and re-fixing back in its original position duly cleaning the external surfaces, connecting all water and electric connections and testing for satisfactory functioning complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement of ventilating fan with plastic body with louvers, 250mm sweep, single phase, 230 volts, 50 Hz. complete all as specified and directed. Make: Bajaj / Crompton / Polar / Havells / Khaitan / Orient

Supply and fix Rigid PVC conduit of size 25mm dia exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. concealed in wall/floor complete all as specified and directed by Engineer-in-Charge. (Notes: Quoted rate shall deemed to include the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface.) Make: AKG/ Atul/ Kalinga/Modi/Precision

Supply and fix PVC junction boxes (1 to 4 way) for 25mm dia pipe complete all as specified and directed.

Supply and fix Decorative wall light fixture made up of Polycarbonate with and including 7W retrofit LED lamp, full white of approved model complete all as specified and directed by Engineer-in-Charge. Make: Philips / Havells / Wipro / Bajaj / Osram

Supply and fix in replacement of 3mm thick phenolic laminated hylam sheet of size 9" X 11" including necessary cutting, drilling holes for fixing of switches, sockets & fan regulators etc and fixing the hylam sheet on existing metal flush box with brass/GI screws with washers complete all as specified and directed by Engineer-in-Charge. Note: S&F of switches, sockets & regulators shall be measured and paid separately.

Supply and fix in replacement of 3mm thick phenolic laminated hylam sheet of size 8" X 5" including necessary cutting and drilling holes for fixing of switches, sockets & fan regulators etc as per site requirement and fixing the hylam sheet on existing metal flush box with new brass/GI screws with washers complete all as specified and directed by Engineer-in-Charge. Note: S&F of switches, sockets & regulators shall be measured and paid separately.

Supply and fix in replacement of 3mm thick phenolic laminated hylam sheet of size 5" X 5" including necessary cutting and drilling holes for fixing of switches, sockets & fan regulators etc as per site requirement and fixing the hylam sheet on existing metal flush box with new brass/GI screws with washers complete all as specified and directed by Engineer-in-Charge. Note: S&F of switches, sockets & regulators shall be measured and paid separately.

trading engineers

JAI BALAJI CONSTRUCTIONS

RAM SARAN SAHU

Dubey Construction Company

FTH Traders

m/s ramesh saran agarwal