PROVN OF STORE ROOM NEAR BLDG NO D3 ECSR AND PROVN OF WAITING SHED NEAR FOL GP OF 225 ASC (SUP) TYPE C FOR COLLECTION PARTIES OF UNIT AND PROVN OF FALSE CEILING ROOF TREATMENT AND MISC WORKS AT S1 APPOINTMENT HOUSE AND PROVN OF RCPC DRAIN COVERS

Amount

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), and removing rubbish off the Premises, complete all as specified and as directed.

Demolition of cement concrete (Un-reinforced) of any description and in any position not otherwise specifically provided for all as specified and directed.

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work, viz. MS Flat Iron (Wind Tie) and Similar Work including MS Bolts, Nuts, etc., complete all as specified and as directed.

Taking down cement plaster of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Taking down soil/ rainwater pipes (any size or pattern) including all fittings heads shoes bends swan necks etc. including cleaning and refixing or removal to store (Measured overall as fixed along the Centre Line over the Fittings and Accessories), complete all as specified and as directed.

Dismantling of 100mm dia cast iron pipe jointed in cement morter in foul places including bend and branch pieces complete all as specified and as directed.

Cleaning of existing covered (partly / semi or fully filled up) drain, of any opening width and depth by removing and refixing of cover-slab, taking out accumulated silt, mud, earth, rubbish, vegetation etc from the drain and flushing with sufficient quantity of water etc. and cutting of the bushes both side of drain upto 0.5 mtr each side and and removing the same to a distance complete all as specified and as directed by the Engineer-in-Charge. Note:-(i) Any damged done by the Contractor during cleaning shall be make good by the Contractor at his own cost upto the satisfaction of Engineer-in-Charge.

Surface excavation not exc 30cm deep and avg 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exc. 1.5 Metre wide and not exc. 1.50 Metre in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exc. 10 Sqm on plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Excavating in post holes (or similar holes) each n. exc. 0.5 cum, getting out returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25 cm watering and removing surplus soil to distance n. exc 50 m and making good surface complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 Cm as in soft/loose soil complete all as specified and directed.

Removing excavated material ( soils of any type) n exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L Plain Cement Concrete type D2 (1:4:8) using 40 mm graded aggregate as in Foundation, Filling and Mass Concrete, complete all as specified and as directed.

M&L Plain Cement Concrete type C2 (1:3:6) using 40 mm graded aggregate) in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases), complete all as specified and as directed.

M&L Plain Cement Concrete type C1 (1:3:6), using 20mm graded crushed stone aggregate as in surface channels and drains complete all as specified and as directed.

M&L Plain Cement Concrete type C-1, (1:3:6) (20mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

M&L Plain Cement Concrete type B-1, (1:2:4) (20mm graded crushed stone aggregate) as in Coping including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

M&L Plain Cement Concrete type B1 (1:2:4), using 20mm graded crushed stone aggregate as in surface channels and drains complete all as specified and as directed.

M&L Plain Cement Concrete type B0 (1:2:4), using 12.5mm graded crushed stone aggregate as in coping complete all as specified and as directed.

M&L Reinforced cement concrete (Design Mix) M-25 (Using 20mm graded crushed stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Foundations including Rafts, Footings, Foundation Beams; Plinth Beams; bases for Columns, etc.; Basement Slabs, Under-reamed Piles and Mass Concrete, complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 as in slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Columns, Pillars, Piers, Posts and Struts, etc. complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Chajja / kitchen rack etc., complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Cutting Holes in Brick Walls, built in Cement Mortar for Taking Out or Inserting Holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1as required in exc. Half Brick but not exc. One Brick thick Walls, complete all as specified and as directed.

M&L Brick work using Pulverizes fly ash bricks of class designation 75, straigth or curved on plan exc 6m mean radius built in CM (1:4) cmplete all as specified and directed.

Labour only Brick Work using Except old bricks obtained from demolition, Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Formwork to Sides of Concrete Founda-tions, Footings, bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of foundation and plinth beams and similar work; Square, rectangular or polygonal, vertical or to batter, flat, rough finished surfaces of concrete, complete all as specified and as directed.

M&L Formwork to Soffits of suspended slab such as Roof slab, Floor slab, landings and similar works horizontal or sloping etc., not exceding 200mm thick ,flat rough finished surfaces of concrete, complete all as specified and as directed.

M&L Use and waste of Formwork to sides of Pillars, Posts, Struts, Piers, Columns and stanchions, flat, rough finished surfaces of concrete, (upto 04 storey high of building) complete all as specified and as directed.

M&L Use and waste of Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bres-Summers, Lintels, Cantilevers, Shelves including supports, overhangs, etc. also splays between floors and beams, etc., flat, rough finished surfaces of concrete, complete all as specified and as directed.

M&L Use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished surface (upto 04 storey High of building) complete all as specified and as directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed.

S&F Plain Colour Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed.

S&F Aluminium door with powder coated anodized aluminium frame of section size 101.60 mm x 44.75 mm x 2.4 mm (jindal section 14021) thick, with shutter of style member size of 85mm x 44.45 x 2.00mm thick (Jindal section 19560), Top/bottom rail of member size 114.30mm x 44.45 x 2.15mm (Jindal section 19574) and lock rail of member size 100mm x 44.45mm x 2.0mm thick (jindal section 19564) with rubber gasket and aluminium glazing clip beading and 100mm mortice locking arrangement ,handle, tower bolt 200mm long per shutter, rollers, etc complete all as specified and directed.

39 S&F Aluminium door with powder coated anodized aluminium frame of section size 101.60 mm x 44.75 mm x 2.4 mm (jindal section 14021) thick, with shutter of style member size of 85mm x 44.45 x 2.00mm thick (Jindal section 19560), Top/bottom rail of member size 114.30mm x 44.45 x 2.15mm (Jindal section 19574) and lock rail of member size 100mm x 44.45mm x 2.0mm thick (jindal section 19564) with rubber gasket and aluminium glazing clip beading and 100mm mortice locking arrangement ,handle, tower bolt 200mm long per shutter, rollers, etc and including Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and complete all as specified and directed. Sqm 2.00 2.00

S&F Mild Steel Butt Hinges, size of Hinges 100mm, medium weight, Cold Rolled and fixed, complete all as specified and as directed

S&F Aluminium anodised, barrel tower bolts of extruded section, 150 mm long and fixed with steel screws complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised 150mm long complete all as specified and directed

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

S&F Mild steel TMT bars 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips (upto 04 storey High of building)complete all as specified and as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete Fe 410-0 W Gde-E-250 quality-A complete all as specified and directed.

M&L Mild steel Steel Work in Tubular /hollow section as trusses, purlin , rafter etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-4923 grade YSt.-240 complete all as specified and as directed.

S&F Mild steel Plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming toFe-410-W (Gde-E- 250 quality -B) complete all as speci-fied and as directed.

M&L Mild steel Framed Work such as Grills, Gratings, etc. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as speci-fied and as directed.

M&L Mild steel Framed Work such as hung as gates including pintle hinges,stops, hand-made sliding bolts etc ,Grills, Gratings. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as speci-fied and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and directed.

S&F Pre-painted colour galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L 4mm thick suspended false ceiling HPSC (high pressure steam curved) pre-primered fibre cement non asbestous building board similar to E-Board Classic placed in a grid of size 605x605mm with aluminium powder coated angle/channel/tee section duly suspended with 4mm dia GI hanger fixed with GI hooks 4mm dia and fastner as required at the site including two coat of oil bound distemper complete all as specified and directed. Detail of section are as under:- (i) Aluminium Angle 25mm x 25mm x 1.5mmt thick. (ii) Aluminium Cross Tee 25mm x 25mm x 1.5mmt thick. (iii) Aluminium Main Tee 25mm x 38mm x 1.5mmt thick. Note:-The bidder quoted rate included for all straight, Raking or circular cutting, wastage on ceiling board

M&L Mild Steel Plain Black Sheet 1.6mm thick in Hearths, covering to Door Shutters, covering to steel gates, etc. cut to size edges beaded if directed, holes punched including round headed Screws Clout screws including bending, turning up, mitred angles, stopped ends, outlets, etc. as required, including taking down old unserviceable one complete all as specified and as directed.

Stripping of old tarfelt including layer of plaster or morter of any type treatement carefully from roof surfaces (without damage of roof) and roughening of surface of old concrete roofing by picking sweeping cleaning and washing down with water to remove dust as directed and specified.

Materials and labour for 20 mm thick screed bed of bedding layer in CM 1:4 surface finished even and smooth without using extra cement for padding including neat cement slurry @ 3.0 kg per Sqm complete all as specified and directed.

Materials and labour for 20 mm thick rendering of fair surfaces of brick or concrete surface in CM 1:4 surface finished even and smooth without using extra cement complete all as specified and directed.

M&L Water Proofing Treatment on existing cleaned RCC Roof with the following Specifications and Manufacturer's instructions, complete all as specified and as directed :- (a) Preparing and cleaning of fully dry surface as per IS:3067-1966. (b) Applying tack coat industrial Bitumen @ 1.2 Kg per Sqm over the Cleaned Plastered Surface. (c) Applying a layer of APP based Polymeric Membrance; modified prefabricated five layer ,3.0mm thick (minimum) weighing 3.00 Kilogram per Square Metre (reinforced) with Polyster Non Woven Fabric weighing not less than 160 Grams per Square Metre by Torch application. The overlaps shall be minimum 100mm on the Transverse direction and 75mm on Longitudinal direction. (d) Applying two coat of bitummen based UV paint with Aluminium finish @ 0.11 Litre per Sqm over APP based Polymeric Membrane.

M&L Cement Concrete type D2(1:4:8) using 40mm graded crushed stone aggregate 75mm thick as in sub base of floor, foundation filling etc complete all as specified and as directed.

M&L Cement Concrete type D2(1:4:8) using 40mm graded crushed stone aggregate 100mm thick as in sub base of floor, foundation filling, path/hard standing etc complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L Cement Concrete type C2 (1:3:6) using 40mm graded crushed stone aggregate 100mm thick as in sub-base of floor and paving, finished Concrete Surfaces Even and fair without using Extra Cement, complete all as specified and as directed.

M&L Cement Concrete type B0 (1:2:4) (12.5mm graded aggregate) 25mm thick, in Flooring, finishing concrete surfaces even and smooth complete all as specified and as directed.

M&L Cement Concrete type B1(1:2:4) (20mm graded crushed stone aggregate) 40 mm thick as in Floor, finishing Concrete Surfaces Even and fair without using Extra Cement, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed.

M&L Coloured /digital vitrified ceramic floor tiles dark shed 10 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n. exc. 0.36 sqm (600mm x 600mm x 10mm) as in floor etc, set and jointed in neat cement slurry and pointed in white/coloured cement to match the existing floor make incl 15 mm thick screed bed or bedding of layers in CM 1:6 complete all as specified and as directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, complete all as specified and as directed.

M&L Pre polished Chequered cement concrete tiles of size 300mm x300mm x25mm thick, with grey cement and no pigment, jointed in neat cemnt slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 including taking out old unserviceable chequered tiles complete all as specified and as directed.

S&F RCPC (Reinforced Cement Polymer Concrete) drain cover slab of size 750mm x 450mm x 75mm thick, of capacity 3 MT placed in proper position complete all as specified and as directed.

M&L rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces even & smooth without using extra cement complete all as specified and directed.

M&L Rendering 15mm thick in Cement Mortar on fair faces of brick work or concrete surface of external wall in two layer, first layer 10 mm thick in cement morter (1:4) and top layer 5 mm thick in cement morter (1:4) using water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and as directed. . (NOTE:-WPC shall be measured and paid separately)

M&L rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces even & smoth without using extra cement complete all as specified and directed.

M&L rendering 5mm thick in CM (1:3) as in ceiling surfaces even & smooth without using extra cement complete all as specified and directed.

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed. Make:- STP NO 1/ PEDILITE(DR FIXIT)/ FOSROC/ CICO/ SIKA

M&L Preparing new Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 3mm thick water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Cement Base Paint over a coat of primer complete all as specified and as directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) bend any radius 110mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal 110mm bore complete all as specified and directed.

S&F PVC (SWR) 110mm bore Branch pieces, single (equal or unqual), ordinary or inverted (spigot or socket type) or with parallel branches or fitted with oval access doors as in repair complete all as specified and directed.

S&F Cast Iron Soil, Waste and Vent Pipes 100mm bore (dia), Sand Cast, in any Length with or without Ears, with Cement Joints in Cement Mortar 1:1, fixed to Walls, complete all as specified and as directed.

S&F in repair Cast Iron Bend 100mm bore (dia), any radius, Disminishing Pieces or Tapers (Large Bore measured) and fitted with Oval Access Doors including Jointing with Cement Mortar 1:1, complete all as specified and as directed.

M&L for Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS - 694 1990 drawn through and including PVC concealed conduit 20mm dia medium duty with all accessories including fabricated 1.6 mm thick MS terminal boxes fixed flush with wall surface with 3 mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 sq mm FRLSH stranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for one light or fan point controlled by one switch single pole one way for light/ ceiling fan/ exhaust fan/call bell point/ Switch socket outlet 5 amps incl Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3, cutting not exceeding 10 cm girth in brick walls etc complete all as specified and as directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

All as per item No. 84.00 here-in-before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-charge.

All as per item No.84.00 here-in-before but one 3 pin 5 amps switch socket outlet on the independent board with other switch complete all as specified and directed by Engineer-in-charge.

M&L Point wiring with 2.5 sqmm (Nominal Area) PVC insulated stranded single core unsheathed FRLSH copper conductor cable 1100 Volts grade drawn through with and including PVC concealed conduit 20mm dia medium duty with all fittings and accessories of casing caping (like Tee, Bend etc) complete fixed to walls / ceiling etc with and including 2.5 Sqmm (nominal area) PVC insulated unsheathed, stranded, single core FRLSH copper cable as earth continuity wire connecting to common earth point (including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC /plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. for mounting sockets for 5 pin, 16 Amp socket outlet on independent board complete all as specified and directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (ii) Cutting Chases pinning shall be measured and paid separately under relevant item of sch A

S&F Switch piano, flush type, SP, one way, 5/6 Amps 230/240 Volts, white/ivory finish complete all as specified and directed.

S&F Switch socket combination multipurpose 2 in 1, 3 pin 6 Amps 230/240 volt flush type complete all as specified and as directed.

S&F Socket outlet 3/5 pin, 6 Amps, 240 volt flush type complete all as specified and as directed.

S&F Switch socket combination multipurpose 2 in 1, 3 pin 15 Amps 230/240 volt flush type complete all as specified and as directed.

S&F Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

S&F Energy efficient LED fittings of capacity 1 x 20W suspended type / wall mounted type complete with LED tube Lamp and fitting with copper flexible PVC cable of 0.50 sq mm twin core not more than one metre in length complete all as specified and as directed.

S&F Sheet metal enclosure for DB's when MCBs to be used 8 way single pole and neutral double door with 200 amps rated bus bar complete 240 volts complete all as specified and as directed.

S&F MCB 6 to 32 Amps, SP, 240 Volts , 'C' curve breaking capacity 10 kA complete all as specified and as directed.

S&F MCB 32 Amps, DP 240 Volts ,C- Curve breaking capacity 10 KA including necessary connection complete all as specified and as directed.

M&L Sub main wiring with 2 runs of single core FRLSH type PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm and one run of PVC insulated unsheathed multistrand copper conductor FRLSH type of size 4.0 Sqmm as earth lead drawn into rigid non metalic PVC conduit of size 25 mm dia including all fittings complete all as specified and as directed. Note:- Two runs of 4 Sqmm conductor as main wire and one run of 4 Sqmm conductor as earth wire with one run of PVC conduit shall be measured as one unit.

Supplying and fixing new ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete with all the connection as directed.

RADHA ENTERPRISE (BID ID -3277507)

MS AP CONSTRUTION AND CO (BID ID -3276832)

NIRMAL DAS AND CO. (BID ID -3276995)

SENCO (BID ID -3275800)

TAPAS ENGINEERING CO (BID ID -3276167)

JHAWAR SUPPLIERS (BID ID -3274785)

ROY CONSTRUCTION (BID ID -3275171)