CONSTRUCTION OF BPHU (BLOCK PUBLIC HEALTH UNIT) IN PHC PESHRAR BLOCK PESHRAR DIST LOHARDAGA

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.

Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 A one brick on edge soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Suspended floors, roofs, landings, balconies and access platform

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. TMT Fe 500

Providing Tor steel reinforcement of 10mm. ,12mm & 16mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (a) 10mm (TMT,Coil Fe 500)(Only valid for Tata (Tiscon),SAIL,JSPL,Electrosteel Ltd. Bokaro and Vizag(RINL))

(a) 12mm (TMT,Coil Fe 500) (Only valid for Tata (Tiscon),SAIL,JSPL,Electrosteel Ltd. Bokaro and Vizag(RINL))

(c) 16mm ( TMT bar Fe 500) (Only valid for Tata (Tiscon),SAIL,JSPL,Electrosteel Ltd. Bokaro and Vizag(RINL))

Providing Tor steel reinforcement of 20mm. 25mm. 28 mm, 32mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (a) TMT bar 20/25 mm Fe 500

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing 12 mm. cement plaster (1:3) with clean coarse sand of F.M 1.5 including screeing. Curing all leads and lifts of water, scaffolding taxes and royalty are all complete as per E/I's specification and direction of E/I.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.

Providing 75 mm thick reinforced designation 75 A Brick work in cement mortar ( 1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

Providing designation 112mm thick reinforced designation 100A brick work with fly ash lime brick (FLAG) conforming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening,carriage of materials,scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of rienforcement)all complete as per building specification and direction of E/I.

75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with adjustable lugs with split end tail to each jamb

Supplying, fitting and fixing 30mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.Powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing average 150 mm thick dry rammed khoa beaten to 112 mm (compacted with water) made of well burnt jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blending the top with cement mortar (1:10) all complete as per building specification and direction of E/l.

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colors and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand ), jointing with grey cement slurry @3.3kg/sqm including grouting the joints with white cement and matching pigments, etc, complete Size of Tile 600x600 mm.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineerin-Charge.Granite work

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/oralkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge.In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)Acid and alkali resistant tile

In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile

Providing 50 mm thick cement concrete flooring (1:2:4) with 20 mm to 6mm size graded stone chips finished with floating coat of neat cement in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty with all complete as per building specification and direction of E/l

Providing and laying 15 mm - 23 mm thick Kota stone tiles in risers of steps, skirting, and pillars of approved size, texture, and color applied over 12mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing to granolithic finish with approved quality of carborundum stone including the cost of curing, taxes, and royalty all complete as per building specification and direction of E/I.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Waterproofing for old and new roof slab: - Providing and laying waterproofing treatment of roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with a brush, roller or spray waterproofing coating as per manufacture specification with following steps:- (a) Surface preparation: - providing and cleaning of the concrete surface to remove dust, oil, and grease including removal of existing loose paint/coating, and laitance by cleaning with compressed air and water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage, and leakage. On identification of seepage, cement grouting to be done with non-shrink expanding admixture of sika India Pvt. Ltd. / MYK Schomberg / Dr. Fixit/ Fosroc or equivalent. Providing and repairing all corners and joints such as those between the parapet wall and roof slab etc shall be chamfered with 150mm X 150mm fillet with mortar ( cement: sand- 1:4) admixed with an acrylic polymer of sika/ Fosroc/ MYK Schomberg / Dr. Fixit/ Fosroc or equivalent. Before chamfering, a prime coat shall be given with the slurry of acrylic polymer. Repairing surface irregularities, damaged concrete base slab, dead crack if any, with acrylic polymer modification repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete. (b) 1st coat:- Apply 1st coat of two-component acrylic modified, ready to use, flexible cementitious material on the surface dry roof and inside wall of parapet wall up to 600 mm by brush or roller. after 1st coat of application, 45gsm of fiberglass cloth to lay when the first layer is still green. 1st coat should be applied @ 1.50 kg/Sqmt/coat. For measurement will be measured (c) 2nd coat:- To apply the 2nd coat of two-component acrylic modified ready to use, flexible cementitious material right angle to the 1st coat over the glass surface. 2nd coat should be applied @ 0.7 kg /sqm/coat. For measurement, Cheniere treated surface will be measured. After three days of drying the 2nd coat. the rainwater outlet is to be plugged and a ponding test is to be done for 48 hours to identify seepage, leakage from the soffit, and if found necessary rectification is to be done as per the satisfaction of E/C. the waterproof coating is to be protected from damage before screed over it. Waterproofing bond:- Sika top seal 109i / Fosroc brush bond RFX/Dr. Fixit pidiffin 2k / MYK Aquafin TG. Product Performance- chemical base part A: acrylic copolymer, Part B: specially graded cementitious powder density 1.6kg/l (mixed density) at +27 degree c tensile strength ~ 2N/mm2 after 28days (with fiber cloth )( According to ASTM D 2370) pull out bond strength ~ 2N/mm2 (concrete failure) (According to ISO 4624) Slant- Shear Bond strength ~4N/mm2 (According to FIP 5.15) elongation at Break ~35% without Fiber Cloth and 20% with Fiber Cloth (According to ASTM D 2370) (d) Protection of the treated surface with PCC:- the treated surface should be covered with 25mm/50mm PCC of M-20 grade (1:1.5:3) with proper slope (1:120) toward the rain outlet in Alterna panel of 2mtx2mt keeping 6mm gape between the plane joint integral waterproofing admixture conforming to IS 2645 @ of 100ml per bag of cement to be added in the screed concrete ( paid separately for this item) all corner shall be chamfered with 150mm x 150mm fillet. The rainwater outlet shall be just leveled with the screed concrete to ensure smooth discharge of water- the peripheral gapes between PVC pipe outlet and concrete surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of sika/ Fosroc/ MYK Schomberg / Dr. Fixit/ Fosroc. For measurement, the entire treated surface will be measured (e) Groove of PCC surface should be filled with polysulphide sealant. (paid separately) . brand- sika/ Fosroc/ MYK Schomberg / Dr. Fixit/ Fosroc. Warranty for five years.

Covering the treated surface with PCC:- 50mm thick Cement Concrete (1:1.5:3) maintaining the slop in 2mt x 2mt panels with approved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F.M 2.5 to 3 including screening, shutting and mixing cement in mixture with an admixture of integral waterproofing and placing in position, striking curing, taxes, and royalty all complete as per building specification and direction of E/I. the panel that has been left should be cast the next day. there should be a 6mm gap between panels. Brand- sika_Plastocote plus, MYK Proof WP 10, Fosroc- conplast x 4211C,Dr. Fixit Pidiproof LW+ or Equivalent.

providing and filling of 6mm thick Groov between 50 mm PCC panels with 6 mm thick 25mm deep thermocol strip and filling the rest 25mm with polysulphide sealant (poring Grade) as per drawing and technical specification and direction of E/I.(With 18% GST) Brand:- Sika-polysulphide, Fosroc-thiols 600, Dr. Fixit pidi seal PS (42P), MYK SEAL PS or Equivalent

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in the ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes, and royalty all complete as per building specification and direction of E/l.

Providing 19 mm thick waterproof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved waterproofing compound including screening, curing with all leads and lifts of water, scaffolding taxes, and royalty all complete as per building specification and direction of E/l.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868,Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basicitem):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.Upto 5mm depth and 5 mm width

Supplying, fitting and fixing 40 mm high vitreous white glazed earthen E.W.C of P trap of parry Hindustan or any other approved I.S.S make including supplying and fixing 15 liters C.I mosquito proof low down fluhing cistern of approved make with complete fitting with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grams 15 mm P.V.C alkathene pipe 45cm .long with brass coupling at both ends and white/black plastic solid state seal and lead of commander cuckoo or other I.S.S.make with hingers or screws etc. painting pipe and cistern etc .with 2coats of approved paints over a coat of red oxide priming ,all complete as per specification and direction of E/I 12.5 lit . Low leve lC.I cistern

Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry of hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32 mm C.I. body brass spindal stop cock of approved quality of weight not less than 350gms 32mm P.V.C. waste pipe 750 mm long with brass coupling at one end making plumbing jonts etc. all complete as per specification and directon of E/I .

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :Size 450x300x150 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings Flexible pipe complete. 32 mm dia

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing clean out pluge with M.S flanged place, blined, 6mm dia nut & gsate and washer fixed to C.I pipe with drip seal joint complete in all complete including cutting and making good the wall and floor whenever re.with 100 mm dia pipe

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length15 mm nominal bore

providing and fixing rainwater ' kurra' size 450 x450mm requierd depth with lead flasing around the pipe with one pipe lead sheet of 3mm thck set on a layer of cold bitumen including heavey duty CI/MS grating as per drawing complete as dwg

Supplying fitting and fixing H.C.L pipes with ear of approved make confirming to I.S.I 1729 including supplying nails and bobins short pieces , cutting loose collars , lead and yarn for making leads caulked pipes to size including earth work or scaffolding where necessary etc . all complete as per specification and of E/I. (a) 100 mm dia

(b) 75 mm dia

(c) 50 mm dia

Supplying and fixing H.C.I fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobines lead and yarn form making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I. (A) H.C.I single junction with door but without ear except socket

(B) H.C.I. Heal rest bend

Supplying all tools and labours and cutting chajja, cornice, for laying H.C.I pipes and making good the same as per specification

and direction of E/I. Cutting drain width wise above G.L for laying H.C.I. pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in (1:4) with neat cement punning as per specification and direction

Making holes in walls for laying H.C.I pipes and restoring the same after pipe laying as per specification and direction of E/I.(i) 125mm dia

Supplying materials and labour for painting the exposed H.C.I pipes and fittings with 2 coats of approved paint over a coat of red oxide primer etc all complete as per specification and direction of E/I. (a) 50 mm dia

(b) 80 mm dia

(c) 100 mm dia

Providing and fixing testing and commsing of UPVC pipe SWR tpe (b) conform to IS : 13592-1992 with all such as bend tee, elbow, Y ofset clearing pipe door clamp and sheet structureal support etc. including cuting the floor wall and making good the same in cemnt concrete 1:2:4 abd cement mortar 1:4. the wall yhikness of pipe and tecnical conform to IS 13592-1992 type 'b' the fitting of pipe dimension to is 14735:1999 the jointing to be complete rubber ring joint solvent 110 mm (OD) SWR pipe

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 25 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc 15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 2 mm nominal bore.

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 25 mm diameter pipe

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): 32 mm nominal bore

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) , including necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing, strong , handling, shifting. Installation testing and commissing of pot table fire Extiguser as describe below 4.5 kg carbon dioxide extinguser is marked with high pressuer dischage tube horn controle valve, CCE approved cylender

6 kg mono ammoternt phosphate (ABC) type carteg oprated

Wiring for light point /fan point/ exhaust fan point/ cell bell point, with 1.5 sq. mm FR PVC insulated copper conductor singel core in surface/recessed PVC conduit, with modular type switch, modular plate sutable GI box etc as required Group C

Wiring for light/power plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, alog with 1 No. 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc as required.

Wiring for circuti/ submian wiring along with earth wie with following size of FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit as required 2x1.5 sq.mm +1x1.5 sqmm earth wire

2x2.5 sq.mm +1x2.5 sqmm earth wire

Supplying and drawing co-axial TV cable RG-6 grand 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in existing surface/ recessed steel / PVC conduit ar required.

Supplying and fixing of the following size of PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 20mm

Supplying and fixing of following modular switch / socket on the existing modular plate & switch box including connection but excluding modular plate etc. as required. 5/6 amps, one way switch

15/16 amps, one way switch

5/6 amps, 3 pin socket outlet

15/16 amps, 6 pin socket outlet

TV antenna socket outlet

Supplying and fixing stepped-type electronic fan regulator on the existing modular plate & switch box including connection but excluding modular plate et. As required.

Supplying and fixing modular blanking plate on the existing modular plate & switch excluding modular plate et. As required.

Supplying and fixing following size / modular, G.I box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 module (78mm x 78mm x 45mm)

4/5 module (78mm x 140mm x 50mm)

8/9 module (78mm x 230mm x 60mm)

supplying and fixing 2 pin 5 amp. Ceiling rose on existing junction box/ wooen block including connection etc. as required.

Supplying and fixing Batten/angle holder including connection etc as required.

Supplying and fixing Ding-Dong sound call bell single phase. 230 volt, complete as required

Installation testing and commssioning of pre-wired. Fluorescent fitting. / compact fluorescent fitting all types, complete with all accessories and tube etc. directly / wall . Including connection with 1.5 sq.mm FR PVC insulated. Copper conductor single core cable and earting etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down road of standerd length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable etc . As required.

Installation of exhaust fan up to 450mm sweep in the exisiting opnening, including making the hole t suit the size of the above fan, making good the damge, connection, testing , commissioning etc. as required

Supplying and fixing following way , horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volt, on surface/ recess, complete with tinned copper bus bar, netutral bus bar, earth bar, din bar, interconnection, powder printed including earthing etc. as reuired. (But with out MCB/RCCB/Isotator) 6 way (4+18), Double door, Horizontal type

Supplying and fixing 6 amps to 32 amps rating, 240 volts, 10KA, "B" curve, miniature circuit breaker sutable for iductive load following Pole in the existing MCB DB complete with connection, eating and commissioning etc. as requird.6/32 amps, singel pole

6/32 amps, TPN

40 amps, TPN

Supplying and fixing following rating, Double pole, (single phase, and neutral), 240 volt, residul current circuite breaker (RCCB),having a sensitive current 30 milli amperes in the existing MCB DB complete with connection, testing and commissioning etc. as required. 63 amps

Providing and Fixing M.V danger notice plate of 200mmx150mm, made of miled steel, at least 2mm thick and viteous enameld white on both side and with inscription in singel red colour on front side as required. Detailes of cost for one each

Earthing with G.I earth plte 600mm x 600mm x 6mm thick including accessories, and providing masonry enlosure with cover plate having arrangmrnt and watring pipe etc. ( with charcoal or coke and salt ) as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required

Suppying & Laying of Follwing size of 1.1 kva grade multiskated copper cunductor PVC insulated calbe including termination complete as per requied existing cable tray 1CX16 Sq mm PVC insulated cu Wire including termination ETC.

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50HZ, single phase supply etc. complete as required 10/12 W LED Tube light

20/22 W LED Tube light

S.I.T.C of 300 mm (12") Exhaust fan sutablie for, single phase supply etc. complete as required

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to IS:374:2019 including wiring the down rods of standard length (upto 30cm) with 1.5 sq.mm. FR PVC insulated, copper wire sutable for 230V 50HZ, single phase supply etc. complete as required. 1200mm (48") BLDC 5 star rating 32 Ceiling Fan

HYDT: of drilling 200 mm x 165 mm x 125 meter deep bore well in all kinds of soil and rock in rural area for installation of pump set with hydraulic DTH Rig machine all complete including all materials, tools,driling rig, air compressure and equipments as well as fule, lubricants and cost of transportation of rig machine annd other vehicle up to Site as per specification and direction of E/I. (a) From 0.00 M to 50.00 M

(b) From 51.00 M to 100.00 M

(b) From 101.00 M to 125.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm clamp

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100 mm dia submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Suppy fitting and fixing of stander make starter pannel bord with arrangment of all necssary protection including all taxes, all complet job as per direction E/I

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work 32 mm nominal dia Pipes

CARRIAGE OF MATERIAL (a) Sand

(b) Stone Chips

(c) Bricks

ADD GST(18%)

LABOUR CESS

Please Enable Macros to View BoQ information