CERTAIN REPAIR TO HARD STANDING, PATH, PAVEMENT AT MD ACCN UNDER AGE B/R-II AT ITARANA CANTT ALWAR

Amount

Demolition of brick work built in cement mortar or cement lime mortar including all quoin arches complete all as specified and directed

Demolition of cement concrete ( unreinforced) ground floor and paving n exc 15cm thick below or above ground level complete all as specified and directed

Demolition of cement concrete ( unreinforced) in any position not other wise specially provided for complete all as specified and directed

M&L 75 mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate) as in foundation filling and mass concrete as floor sub base complete all as specified and directed

M&L PCC (1:3:6) type C2 as in plinth protection/Path/ Hardstanding finish surface even and smooth using extra cement (75 mm thick) incl forming dummy joints at 2 mtr centre to centre and filled with lean mortar (1:8) complete all as specified and directed

M&L for plain cement concrete (1:2:4), type B-2, (using 40mm graded stone aggregate) in foundations, filling, mass concrete etc complete all as specified and directed.

M&L for Vibrator moulded (cloloured) precast concrete interlocking paver block with grey cement and pigment (Lacquer/ Glossy finish) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over and including 25mm thick sand cushion and filled the joints with dry sand after laying the paver block complete all as specified and directed.

M&L for Vibrator moulded (Coloured) precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over 25mm thick sand cushion and filled the joints with dry sand after laying the paver block complete all as specified and directed.

All as per srl item No 8.00 but except tiles

M&L for vibrator moulded precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 grade and fixed with grey cement and no pigment laid over and including sand cussion and filled the joints with dry sand after laying the paver block complete all as specified and directed.

M&L 12mm thick vitrified exterior grade textured finished tiles (ENDURA JOHNSON OR EQUIVALENT HEAVY DUTY TILES (FOR PARKING/PORCH) of size exc 0.09 sqm each but n. exc 0.16 sqm set and jointed in net cement slurry in floor including cement mortar screed bed 1:4, 20mm thick and pointing with admixture of white/colour cement and pigment complete all as specified and directed

M&L chequered cement concrete (coloured) tiles 30cmx30cmx25mm thick with (Lacquer/glossy finish) set and jointed in net cement slurry in floor and pointed with white cement and pigment including cement mortar screed bed 1:4 20mm thick complete all as specified and directed

M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete complete all as specified and directed

M&L 50mm thick PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in floor laid in alternate panels, finishing the cement concrete surface even and smooth with out using extra cement complete all as specified and directed

Forming construction joints 30mm deep and 10mm wide finished with sealing compound Grade 'A' complete all as specified and directed

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors all as specified and directed.

Supply, installation and finishing outdoor synthetic sports flooring system consisting fo 5 layer system with acrylic latex to sub floor followed by primer layer to improve bonding of acrylic paint with sub floor and smoothing surf floor following by dual layers of 100% acrylic base colour coat followed by top colour coat to protect flooring against UV rays final over line marking with acrylic paint complete all as specified and as directed.

M&L brick work with fly ash 'brick straight or curved on plan exc 6m mean radius built cement mortar 1:6 complete all as specified and as directed

All as per srl item No 18.00 but except brick. (old brick to be re used in this items)

M&L rendering 15 mm thick in CM 1:6 on brick/stone masonry surface rendering is o be even and smooth without using extra cement complete all as specified and directed

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

M&L for preparing plastered old surfaces of wall by washing down & applying one coat of cement base paint complete all as specified and directed

S&F for 75mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard, minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified & as directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide complete all as specified and directed.

Preparation of newly concrete surface as kerb stone surface and applying two coat of synthetic enamel paint over a coat of primer as approved complete all as specified and directed.

M&L providing cement concrete (1:2:4) type B1, using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses , lacing courses, parapets and railings upto 60cm in height, copings kneelers, apex stones, bed plates, kerbs, water through and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

Dismantling posts or struts (steel or RCC or Wooden) embedded in concrete, any section, including taking out embedded portion and making good the disturbed surface complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling AC/CGI/Fibre sheet (Corrugated, Semi corrugated etc) as in roof etc complete all as specified and directed.

Steel work as in tubular section ( in any description) including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

S&F for preparation of new steel surface/old untreated of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and directed.

M&L in replacement of precast cement concrete louvres and jallies, 40 mm thick (measured solid), including all moldings but excluding frame type B0 (1:2:4) (12.5 mm size graded stone aggregate) set in CM (1:4) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Providing precast cement concrete type B-1 (1:2:4) (20mm Graged aggregates) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weathering’s, throating etc. and setting in mortar complete with joints to match complete all as specified and directed.

S&F in repair of 3mm thick Aluminium composite panel (ACP) board of size 4' x 5' (n.exc 20 sqft) fixed on both sides (board shall be rectangular or pentagular shape) ACP board to be fixed on grid frame work with SS screws/ rivets, made of 20mm stainless steel square tube of 1.25 mm thick of SS 304 series and fixed on the perimeter of 40 mm dia stainless steel tube of 2mm thick of SS - 304 series. A 20 mm tube of 1.25mm thick of SS series 304 of 05 Nos and 50mm long support to be provided to fix to 40mm thick frame. A grid frame to be provided in side 40mm thick frame of size 20mm square of 1.25mm thick not exe 600mm centre to centre on both ways to support the ACP boards. The board shall be sheated with high intensity retro reflective sheet of blue colour, computerised designed writing letter/figures in (Block, Roman, Italic style or in Indian languages where required)/ index hands (natural size)/ arrows/stops/ commas /short lines/ dashes/hyphens/ bracket, holograms etc where necessary shall be made high intensity reflective sheet with in white colour letter, shape and sizes as required and approved by GE. Letters not exc 200 nos on each face of the ACP Board. Each face to have a border line of 25mm wide with white colour high intensity retro reflective sheet/tape. The sign board to be supported on 2 Nos post of 60mm dia and 2.5mm to 3.0mm thick stainless steel pipe of SS - 304 series, exc 3m and not exceeding 4m in height with round moulded design cap on top. Pipes of the boards to be fixed in ground with PCC 1:2:4 type B2 (using 40mm graded stone aggregate) in post holes of sizes 45cmx45cmx75cm depth (post holes and concrete includes in the rates) complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304), ornamental gate, railing made of hollow tubes, channels, plates etc., including laser cutting, welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including laser cutting and fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement etc complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 (Using 12.5 mm graded stone aggregate) in coping, hold fast block including weathering slightly rounded and chamfered angle including necessary form work and finish of exposed surfaces of concrete as described in SSR Part-II) complete all as specified and directed.

Ashish Sehgal and Co. (BID ID -3406870)

ALAKNANDA ENTERPRISES (BID ID -3408100)

M/s Laxmi Enterprises (BID ID -3415451)

GAR CONSTRUCTIONS (BID ID -3407779)

Radha Enterprises (BID ID -3406798)

shiva construction (BID ID -3415317)