SPECIAL REPAIRS TO BLDG No. 32 OF HQ JL WING, THE INF SCHOOL BELGAUM AND PROVISION OF CERTAIN REVENUE AND MINOR WORKS UNDER GE BELGAUM

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of PCC solid block masonry built in cement mortar pillars, etc. in any position below or above ground level all as specified and directed.

Cutting chases for concealed water tubing and making good in CM 1:3 cutting not exceeding cm girth in stone wall as specified and directed.

Dismantling timber scantlings 40 sq.cm and over in section, in any position, in un-framed work all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area n exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Dismantling of corrugated or semicorrugated Asbestos Cement sheets in roof coverings including ridges, valley gutters, etc. all as specififed and as directed.

Dismantling wall or ceiling boards or insulation boards/ slabs of any thickness including cover fillets all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

Hacking out old broken glass (any thickness/ size, quality or description) from wooden frames, glazed with putty or fixed with beads all as specified and directed.

Taking up or down 15mm bore steel water tubing and connections all as specified and directed.

Taking up or down 20mm bore steel water tubing and connections all as specified and directed.

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread, levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L for plain cement concrete 1:4:8 type D2, using 40mm graded stone aggregate in foundation, filling, mass concrete, levelling courses and sub bases all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10cm width, blocks cast in PCC 1:3:6 type C0, using 12.5mm graded stone aggregate, set in CM 1:6 complete all as specified and directed.

M&L plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in coping, bed blocks, benching in channels, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L plain cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in surface channels and drains all as specified and directed

M&L for extra for forming fair finished drain or channel of 30cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

M&L for providing precast cement concrete 1:2:4, Type B1, using 20mm graded stone aggregate, as in kerbs, with rounded or chamferred edges including all mouldings, set in cement mortar 1:6 including demolition of existing kerbs of any description and size all as specified and as directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work all as specified and directed.

Fixing only serviceable timber scantling of any description obtained from dismantling in un-framed work all as specified and directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 35mm thick 2nd class hard wood glazed/ gauged shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 30mm thick 2nd class hard wood glazed/ gauged window/ vemtilator shutters, open rebated and prepared to receive glass, gauze, etc. edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (b) and fitted to chowkats all as specified and as directed.

M&L for aluminium sliding windows (Triple track), fabricated to required size with standard aluminium anodised sections, with bottom track of size 92 x 31.75 x 1.6mm, side and top frame of size 92 x 31.75 x 1.4mm, top and bottom shutter rail of size 39x17x1.4mm, outer style of size 39 x 17 x 1.4mm, interlock style of size 39 x 27 x 1.4mm, including provision of 4mm sheet glass ordinary quality for panels including provision of all hardware fittings such as handles, locking arrangements, rubber gaskets, rollers, spring catchers etc. complete all as specified and directed.

S&F in repairs steel ventilator/ windows with top hung shutters including hinges, steel peg stay, complete all as specified and as directed.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on single side reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F 2nd class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles exc 200 cucm nut n exc 50 cucm all as specified and as directed.

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F aluminium anodised barrel tower bolt 100mm size all as specified and directed.

S&F aluminium handle, 'D' type, anodised 150 mm in size all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F in repairs Harrison rails, mild steel chromium plated with fixing brackets, stops, rollers etc. all as specified and as directed.

S&F in repairs brass knobs, 35 to 40mm dia, suitabe for curtain rods fixed with nut and screw and washer all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, conforming to Fe-410-W Gde E-250, quality A, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging, fastening and fixing complete all as specified and as directed.

M&L for 0.8mm thick mild steel, plain black sheet as in covering to door shutters, wall cladding, water tanks, water troughs, ducts, etc. cut to size, edges beaded if directed, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required all as specified and as directed.

M&L for mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates complete all as specified and as directed.

M&L for mild steel flats for wind ties for roof including securing bolts and similar works, conforming to Fe-290 Gde E-165 all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roof covering/ claddings to wall, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S&F PVC (SWR) eaves gutter half round/ square/ trapezoidal profile 150mm bore including pipe accessories PVC holder bats bolts nuts etc. including taking down existing unserviceable gutters of any description and size and making good disurbed surfaces all as specified and directed.

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminum anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 50mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 100mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in paving/ hard standing/ floor and finishing the concrete surface even and smooth without using extra cement and making impressions of expanded metal while the concrte is green all as specified and directed.

M&L for coloured matt finished ceramic tiles, edge cut, 9 to 10mm thick area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for coloured matt finished ceramic tiles, edge cut, 9 to 10mm thick, as in skirting, dado, etc. suitable to match with the size of floor tiles, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 10mm thick backing coat in cement mortar 1:6 all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 6 to 7mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for coloured glazed ceramic tiles 300mm x 450m size, 7 to 8mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut granite stone slab, premium quality, any colour, 18 to 19mm thick, set and jointed with neat cement slurry laid over and including 15mm thick screed bed in cement mortar 1:4 and pointed in white cement (1:2) mixed with colouring pigments to match with the shade of slab, as in platforms, steps, cills, etc. including rubbing and polishing complete all as specified and directed.

M&L for coloured polished designer cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for 80mm thick machine pressed precast concrete interlocking coloured paver blocks with glossy finish on top grade, M-40, any shape and size with glossy finish on top confirming to IS 15658-2006 all as specified and directed.

M&L for crushed stone sand (M-sand/ Robo sand/ i- sand) cushioning under interlocking paver blocks including watering and consolidation complete all as specified and as directed.

M&L for plain cement concrete 1:3:6, type C1, using 20 mm graded stone aggregate, 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on stone masonry surfaces or other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M & L for 4mm thick sheet glass ordinary quality and glazing with oil putty/ neoprene beading in square n. exc 0.5 sqm in each pane all as specified and directed.

M&L for two coats of oil bound distemper over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper any colour, over a coat of primer over 1mm thick layer of wall care putty, on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior emulsion paint over a coat of primer on newly plastered surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for preparation of old wooden surfaces of any discription over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of new steel surfaces not exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for 1000 litres capacity rotational moulded polyethylene (HDPE) water storage tank, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including dismantling andtaking down existing unservceable tank of any description complete all as specified and directed.

S&F in repairs 20mm dia PTMT ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed.

S&F 15 mm bore UPVC water supply pipes, 10kgf/ sqcm, including all fittings such as elbow, reducer, tee, couplers, short pieces, connectors etc. fixed to walls , ceilings with PVC batten holders all as specified and as directed.

S&F 20 mm bore UPVC water supply pipes, 10kgf/ sqcm, including all fittings such as elbow, reducer, tee, couplers, short pieces, connectors etc. fixed to walls , ceilings with PVC batten holders all as specified and as directed.

S&F in repairs 15 mm bore Bib tap, long body, brass chromium plated, fancy type with wall flange, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F in repairs 15 mm bore 2 way Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed. Make: Continental series of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Continental series of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs 15mm bore angle stop valves, brass chromium plated, fancy type, high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs vitreous china oval type wash basin, white, size 550x400mm, including provision of 15mm bore brass CP pillar tap, 15mm bore PTMT angle stop cock, 450mm long PTMT connections, PVC waste pipe and coupling, CI brackets and cutting for and pinning in ends of brackets or erecting stands etc. all as specified and directed.

S&F in repairs vitreous china squatting pan, Orissa pattern, size 580mm x 440mm, white, with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap including provision of lime concrete bedding etc complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, plastic water closet seat of any colour as approved by GE, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, fixing bolts etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F in repairs syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F in repairs soap dish vitreous China, white, approximate size 160x 160x90mm, fixed to plugs with chromium plated brass screws all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, 600mm long all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail 600mm long with and including chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F in repairs 1mm thick stainless steel sink with draining board, overall size not less than 915x460mm, bowl size not less than 410x330x160mm, with plug, washers and wastes including bedding in cement mortar, fixing cantilever brackets and connecting union to pipe all as specified and as directed.

S&F in repairs 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints/ solvent cement, fixed to walls/ laid in floors/ laid in trenches all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) bends any radius all as specified and directed.

S&F in repairs 150mm size PVC grating square or round all as specified and directed.

S&F in repairs PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

Taking down carefully point wiring of any description complete for light, fan, 5 A socket, 15 Amps socket, 2 way points and bell point etc including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, bells, holders, light fittings, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC conduit/ PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 1/2 module PVC surface mounting box with standard white modular cover plate & frames for mounting modular type switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed.

All as described in item No. 99 but for one fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 99 but for one 05 Amps socket outlet on independent board.

All as described in item No. 99 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 99 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F modular switch, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, 1 module, 1 way, 16 Amps 230 volts, AC, all as specified and directed.

S&F modular socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F modular socket outlet, 2 module, 16 Amps 3 pin 16 Amps cum 3 pin 5 Amps multipurpose all as specified and directed.

S&F modular fan regulator, step type, 2 module, 120 Watts, 230 volts, AC, all as specified and directed.

S&F ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 20W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 1x 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 10W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F in repairs energy saving surface mounted, decorative oval bulk head edge-lit LED luminaire 10W, comprising of high brightness LEDs. comprising of high brightness LEDs complete with all accessories internally pre wired complete including provision of 10 Watts high brightness LEDs 6000K, suitable size wooden board with sunmica top and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block complete all as specified and directed. Make: Havells HEXA or equivalent in CG/ PHILIPS/ WIPRO

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP66 protection, 6000K and impact resistance IK07, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F in repairs Single pole and neutral enclosure, powder coated, with a two pin earth plug and socket complete, 20 Amps, 240V, including provision of one single pole MCB 20 Amps 'C' curve type all as specified and as directed.

S&F in repairs, MCCB VTPN DB 12 Way, vertical type, suitable for MCCB as incomer 415 volts rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCCB DB on board complete all as specified and directed.

S&F in repairs, MCB DB SPN 12 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs MCCB TP 125 Amps ,25KA, 415 Volts, AC supply, fixed thermal magnetic settings, all as specified and as directed.

S&F MCB DP 63A 'C' series 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB DP 40A 'C' series 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, 3 blades, Star rating with all accessories complete including taking down existing unserviceable ceiling fan of any description and size from the location and setting aside for fixing/depositing to MES E/M store all as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in Crompton Greaves/ USHA

S&F in repairs 3 core flexible copper conductor cable of size 0.5 sqmm, 100 volts grade, connecting from ceiling rose to connector block of fan all as specified and as directed.

M&L for 50mm dia GI pipe medium grade cut to required length as per site requirement and fixed into walls in single piece without any joints as in supports for hanging of ceiling fans complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

M/s. N D KALING

DHANSHRI ENTERPRISES

ASHOK M RAJGOLKAR

SAMARTH ASSOCIATES

M/s. J P CONSTRUCTIONS

M/s.Y.N.PATIL

M/S MAHADEV M PATIL

M/S VISHWAROOP ELECTRONICS AND ELECTRICALS