GE 861 EWS-67/2024-25

Amount

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in ground floors and pavings n.exe 15 cm thick below or above GL complete all as specified and directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters exc 1.5 sqm but n exc 4 sqm each (w/o taking of shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n.exe 1.50 Sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exe 1.00 sqm but n.exe 2.00 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description n.exe 1.00 sqm each complete all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in cement mortar 1:6 on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for Non skid ceramic coloured joint free tiles 7mm to 8mm thick (square/ rectangular), area of each tiles exceeding 0.11 sqm but n exc 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:6) for laying floor finish complete all as specified and directed by Engineer-in-Charge.

M&L for Non skid ceramic coloured joint free tiles 7mm to 8mm thick (square/ rectangular), area of each tiles exceeding 0.06 sqm but n exc 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:6) for laying floor finish complete all as specified and directed by Engineer-in-Charge.

M&L for 25mm thick PCC (1:2:4) type B0 using 12.5 mm graded crushed stone aggregate as in floor to receive floor finishes etc. complete all as specified and directed by Engineer-in-Charge.

S&F vitrified ceramic dark shade/double charged/ultra charged/Granite /Marble /wood textures coloured tiles 10mm thick (square/rectangular) polished, area of each tiles exc 0.36 sqm but n exc 0.42 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles in vertical surfaces 350 x250x7/450x350x7 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10mm thick cement plaster in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

M&L 2nd class hard wood, plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class hard wood 40mm thick panelled shutters, Plain framed, panelled shutter (one panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated and fixed to chowkhats complete all as specified and directed by Engineer-in-Charge.

Supply and fixed 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc (internal sash bars) edges of framing plane, chamfered or rounded fitted and mitred beads for securing glass etc size of members as specified in SSR Part-I Section 8 clause 8.24(a) (kail) complete all as specified and directed by Engineer-in-Charge.

S&F 30 mm thick 2nd class hard wood glazed and skeleton windows/ ventilators shutters open rebated and prepared to receive glass, gauge etc , divided into square with plain chamfered or rounded, mitred and rebated sash bars any numbers , provided with stiles and rails as specified in SSR part I section 8 clause 8.24 (b) complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelaminated PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and gap insert for top rail and bottom rail panelling of plain colour PVC to sheet to be fitted in the MS frame welded / sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts extruded section of size 200 mm complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts extruded section of size 150 mm long complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handle extruded fabricate type anodised of size 150 mm complete all as specified and directed by Engineer-in-Charge.

S&F for butt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F for butt hinges 75 mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F MS rat tail spring including roller & roller plate complete 300 mm size complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

M&L for fixed in repairs 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane including hacking out old glass panes complete all as specified and directed by Engineer-in-Charge.

M&L 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

M&L 4mm thick figured glass pin headed type and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane including hacking out old glass panes complete all as specified and directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40 mm graded crushed stone aggregate ) as in sub base for receiving floor finishes etc. complete all as specified and directed by Engineer-in-Charge.

M&L for chequered cement concrete tiles 30cm x30cmx25mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Dismantling water storage tanks of any description, exc 250 & n.exc 500 litres capacity and removing from site complete all as specified and directed by Engineer-in-Charge.

S&F rotational moulded polyethylene 500 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connections of flush pipe to squat pattern closet including lime concrete bedding and all joint making good to the floor complete all as specified and directed by Engineer-in-Charge.

S & F in repairs vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (min), with grating and union for discharge pipe including, flush pipe & waste pipe) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs floor stain less steel gratings, 125mm dia complete all as specified and directed by Engineer-in-Charge.

S&F in repairs PVC valve less 10 litre capacity syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous china wash hand basin, Vitreous china white, flat back, size 550 x 400 mm with brackets, including cutting for and pinning in ends of brackets or erecting stand including S&F of 15mm bore CP pillar tap, waste coupling and 32mm dia PVC waste pipe) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm size PVC connection with PTMT nuts of 600 mm long complete all as specified and directed by Engineer-in-Charge.

S&F in repairs swivel shower of PTMT any colour with arm, 195 mm long with bend of 45 degree with flange (both min wt 80 gms) complete all as specified and directed by Engineer-in-Charge.

S&F 110 PVC (SWR) WC connector bent type complete all as specified and directed by Engineer-in-Charge.

S&F cast iron Nahani trap 75 mm dia including jointing to pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore fancy type CP bib taps cast copper alloy with crutch or butterfly handle, screwed down for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore CP stop valve cost copper alloy screwed down, high pressure with crutch or butterfly handle fancy type complete all as specified and directed by Engineer-in-Charge.

S&F & repairs 15 mm bore stop valves, CP fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy screwed down, high pressure fancy type complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15mm bore GI Tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20mm bore GI Tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore GI tubing medium grade galvanised with all fittings and fixed complete to walls & floors etc. complete all as specified and directed by Engineer-in-Charge.

S&F 20mm bore GI tubing medium grade galvanised with all fittings and fixed complete to walls & floors etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brass chromium plated tubular towel rail with brackets, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and fixing to flushing cistern, brackets, flushing pipe etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore brass CP mixer for mixing hot and cold water screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for 20mm dia iron pipe and fixed (minimum weight 15mm-142gms/20mm 210gms/25mm 455gms/40mm 690gms complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Pillar tap 15mm chromium plated fancy type cast copper alloy with crutch or butter fly handle, screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs bib tap 15mm PTMT any colour high pressure screwed down for iron pipe and fixed ( Minimum weight 90gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 20mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed complete all as specified and directed by Engineer-in-Charge.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning for refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floor complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floor complete all as specified and directed by Engineer-in-Charge.

S&F 75mm PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

S&F 110mm PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

S&F 110mm PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

S&F 75mm PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs, weather boardings, plywood including cover fillets etc. complete all as specified and directed by Engineer-in-Charge.

S&F for anodised aluminium snap grid of size 605 x605 mm frame work for false ceiling including straining with GI wire 4mm dia complete all as specified and directed by Engineer-in-Charge.

S&F for 10mm thick PVC insulation panels with EPS stuck to 1 mm thick plain PVC sheet suitably placed in false ceiling grid made of aluminium GI/MS as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

S&F for solid PVC wall panelling decorative type consisting of 5mm thick plain colour PVC pre-laminated sheet inclusive of solvent cement and fixing at site on PVC frame/wooden frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

S&F for 5mm thick PVC sheet fillets of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class soft wood plain fillets square rectangular or triangular in section clean sawn fixed with nails Sectional area exc 06 but not exc 13 sqcm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 40mm thick, 2nd class hardwood planks, planed one side with butt joints and fixed with nails fixed in any situation complete all as specified and directed by Engineer-in-Charge.

M&L in repairs for weather boarding in 2nd class hardwood clean swan, plain, 20 mm thick or feather degrees, 15 mm to 20 mm thick and fixed with 30 mm laps joints complete all as specified and directed by Engineer-in-Charge.

S&F in repairs timber frame in second class hard wood as in scantling etc. 40sqcm and over complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting any gauge, thickness including roof covering etc. complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets 0.50mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheets 0.50mm thick as in ridge of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

M&L for preparing NEW plastered surfaces of walls and applying two coats of cement base paint on walls over a coat of alkali-resistant primer complete all as specified and directed by Engineer-in-Charge.

M&L for applying 3mm thick wall care putty on wall including preparation of new surfaces plastered or unplastered surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali?resistant priming paint complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint on NEW WOODEN surfaces over a coat of pink primer including preparation of surfaces, over 10cm width or girth complete all as specified and directed by Engineer-in-Charge.

M&L for preparing new plastered surfaces of walls and applying three coats of white wash on walls complete all as specified and directed by Engineer-in-Charge.

M&L for preparing old plastered surfaces of walls and applying two coats of white wash on walls complete all as specified and directed by Engineer-in-Charge.

S&F in repairs plain mild steel wire, 4.0 mm dia galvanised class 3 in detached work such as line wire for fixing mosquito nets and fixing including straining bolts, hooks, eyes etc. complete all as specified and directed by Engineer-in-Charge.

M&L for kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

All as per item no. 88 above but on vertical surfaces of walls /skirting/dado etc over and including 10mm thick cement plaster in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Taking down copper/aluminium point wiring light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engineer-in-Charge.

M&L for Point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including PVC casing and capping/Conduit medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size or PVC Gang Box all as directed by Engr-in-Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-91 here in above but for one 3 pin 5A socket outlet independent controlled by one switch complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-91 here in above but for one 5A socket outlet on the same board controlled by one switch complete all as specified and directed by Engineer-in-Charge.

All as per srl item No-91 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed by Engineer-in-Charge.

M&L for submain wiring in replacement with two single core PVC insulated flexible copper conductor cable of size 4 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 4 Sqmm as earth lead in & including concealed PVC casing capping medium grade 2mm thickness ISI marked or cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification including taking down old unserviceable complete all as specified and directed by Engineer-in-Charge.

M&L for submain wiring in replacement with two single core PVC insulated flexible copper conductor cable of size 6 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 6 Sqmm as earth lead in & including concealed PVC casing capping medium grade 2mm thickness ISI marked cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification incl taking down old unserviceable complete all as specified and directed by Engineer-in-Charge.

M&L Switch piano flush button single pole one way 5 amps 240 volts complete all as specified and directed by Engineer-in-Charge.

M&L Switch Socket combination, 6 pin 5 and 15 amps multi purpose 2 in 01 flush type, 230 volts complete all as specified and directed by Engineer-in-Charge.

M&L Switch Socket combination 2 in 1, 5 Amps flush type, 230 volts complete all as specified and directed by Engineer-in-Charge.

M&L Socket 2 in 1, 5 Amps flush type, 230 volts complete all as specified and directed by Engineer-in-Charge.

M&L for Socket 5/15 amps flush type, 230 volts complete all as specified and directed by Engineer-in-Charge.

M& L for Ceiling rose surface Bakelite 2 to 3 terminals complete all as specified and directed by Engineer-in-Charge.

M&L Switch piano flush button single pole one way 15 amps 240 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically complete all as specified and directed by Engineer-in-Charge.

S&F Lamp holder insulated body with back plate for batten fittings complete all as specified and directed by Engineer-in-Charge.

S&F bell push flush type 6 Amps 240 Volt complete all as specified and directed by Engineer-in-Charge.

S&F bell/buzzer AC 230 volts single pole complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for (in repairs) Plug top 3 pin 15 amps 230 volts including taking old plug top complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for (in repairs) Plug top 3 pin 5 amps 230 volts including taking old plug top complete all as specified and directed by Engineer-in-Charge.

Supply & fix for (in repairs) Rigid non-metallic PVC conduit of size 20 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix Rigid non-metallic PVC conduit of size 25 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed by Engineer-in-Charge.

Supply & fix for (in repairs) medium grade PVC casing and capping of size 20 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc including taking down old unserviceable casing & capping complete all as directed.

Supply and fixing (in repairs) PVC Gang box surface type suitable for fixing of 5 pin 15 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge.

Supply and fixing (in repairs) PVC Gang box surface type suitable for fixing of 5 pin 5 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement cable PVC FR insulated unsheathed with flexible multistranded copper conductor of size 1.5 Sqmm 1100 Volts grade as per site requirement of existing colour coding adopted complete all as specified and directed by Engineer-in-Charge. Make : Havells : Basic code No : WHFFDN1.5L11X57/HPL or equivalent in Plaza, Polycab

Supply and fix in replacement cable PVC FR insulated unsheathed with flexible multistranded copper conductor of size 2.5 Sqmm 1100 Volts grade as per site requirement of existing colour coding adopted complete all as specified and directed by Engineer-in-Charge. Make : Havells : Basic code No : WHFFDN2.5L11X57/HPL or equivalent in Plaza, Polycab

Supply and laying in replacement 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular twin core 4 sq. mm complete all as specified and directed by Engineer-in-Charge.

Supply and laying in replacement 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular twin core 6sq.mm complete all as specified and directed by Engineer-in-Charge.

Supply and laying in replacement 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular twin core 10 sq.mm complete all as specified and directed by Engineer-in-Charge.

Supply and laying in replacement 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular twin core 16 sq.mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fix surface and wall mounted LED batten 20 Watt ( white/ warm white) with aluminium housing & integrated electronic driver , extruded Aluminium heat sink provided for efficient heat dissipation , LED life time of 30000* hours complete all as specified and directed by Engineer-in-Charge. Make: Havells Cat Part No: LUMILINEPLUSNEOBS20WLED830SPCSSIND or equivalent /Bajaj/Crompton/Philips

Taking down old Unserviceable Bldg Security light fitting and taken as credit including supply & Fixing building security light fitting LED 25Watt new generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaries with high power LED as light source along with suitable bracket including all accessories complete all as specified and directed by Engineer-in-Charge. Make: Havells, Cat Part No: ENDURAPEARLSL25WLED 757SASYTOPC or equivalent in PHILIPS CAT PART NO BRP042 LED 19 CW MR SI PSU GR OR C&S CAT PART NO DRACO/25W LTESS25WLED

Taking down old/unserviceable Flood lights and S&F LED Flood light of 30 watt Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium flood light with high power LEDs as light source, suitable for highlighting architectural features or Area Lighting. Also suitable to rough services/installations complete with all accessories etc including connecting with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engineer-in-Charge. Make: Havells cat part No JETA QUANTOPLUSFLP30WLED757SYMLENS or equivalent /Bajaj/CG

Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt( White/ Warm White) , 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply, Installation, testing and commissioning of Efficient LED surface 2'x2' luminaire 36 watt fitting ( warm white/ white ) to enhance the delight of occupants with comfortable experience through its classic design & glare free soft illumination White powder coated CRCA housing with seamless front frame with flat non-yellowish diffuser, including necessary connection from ceiling rose to fitting with flexible copper cable of suitable size/core all as specified and as directed. Make: Bajaj cat part No BZSSQL 36W LED WH i or equivalent /Havells/CG/SYSKA. Surface mounted LED luminary with full glow designed luminary > 30% energy saving, maintenance free, CRI 80, System consumption should be between 28- 36W complete all as specified and directed by Engineer-in-Charge. The type shall be of 2'x2'.PHILIPS CAT. No. SM 365C LED 32-6500 PSU OD GR or Havells Cat Part No PLUTO SURFACE 2X2 PLS34W LED 84 OS or C&S CAT PART NO . CYGNUS-CS/36W/2X2/W-LTCSP36W LED 2X2

Supply and fix sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed by Engineer-in-Charge.

Supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. complete all as specified and directed by Engineer-in-Charge.

Supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amps in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 240V, 10KA 'B' curve miniature circuit breaker (MCB) of current carrying SPN 32 Amps capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB) of current carrying SPN 40-63 Amps capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of current carrying capacity TPN 40 to 100 Amps in the DB complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge.

Supply and fix MCCB 4 Pole, 415 V, Adjustable type, 100 Amps with breaking capacity 16 KA complete all as specified and directed by Engineer-in-Charge.

M&L painting of ceiling fan complete , using spray gun, in site with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust complete all as specified and directed

Replacement of capacitor 2/3.15 mfd AC 230 volts 50 Hz complete all as specified and directed by Engineer-in-Charge. Make : Asian/Jyoti/Usha /Apcos

S&F in replacement of capacitor 4 mfd AC 230 volts 50 Hz complete all as specified and directed by Engineer-in-Charge. Make : Asian/Jyoti/Usha /Apcos

S&F in replacement of ball bearing for ceiling fan /exhaust fan any size any make complete all as specified and directed by Engineer-in-Charge. Make : SKF/NBC/ABC.

S&F in replacement of gun metal bush with suitable size, gun metal bush for ceiling fan any make, any size and sweep complete all as specified and directed by Engineer-in-Charge.

M&L for rewinding of AC ceiling fan/wall mounting fan motor as existing at site any make with super enamelled copper winding wire any gauge from 0.315mm to 0.193mm including cutting of old burnt winding. Sleeve work varnishing with `B' class insulation varnish, connection with flexible wire of appropriate size two core copper wire upto connector block qty of copper winding wire not less than 350 grms and not more than 500 grms per fan motor , replacement of capacitor 2 mfd, complete all as specified and directed by Engineer-in-Charge.

M&L for rewinding of exhaust fan motor any size, from 225 to 300 mm sweep with super enamelled copper wire of any size ranging from 0.500mm to 0.285 mm including necessary cutting of old burnt winding wire, cleaning of slots and provision of necessary threading/sleeve work and taking out connection in lead with PVC copper wire of appropriate size upto connector block, capacitor 2/3.15 mfd complete all as specified and directed by Engineer-in-Charge.

Taking down carefully geyser 25/35/50 ltrs capacity from wall after unscrewing nuts/bolts etc. and again refixing in position after repair and replacement of spare parts including testing complete all as specified and directed by Engineer-in-Charge. Note: spare parts shall be measured and paid for separately under respective items.

S&F in replacement of unserviceable heating element AC 230 Volt of rating 1500W ISI mark (triangular/round) as per existing any type complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of unserviceable heating element AC 230 Volt of rating 2000W ISI mark (triangular/round) as per existing any type complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of unserviceable thermostat switch AC 230 Volt adjustable range from 0-90 degree Celsius complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of unserviceable Indicator lamp round/square type suitable for geyser 25-50 ltrs all as per sample AC 230 Volts complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of unserviceable auto cut switch suitable for geyser 25-50 ltrs all as per sample AC 230 Volts complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of unserviceable geyser assembly suitable for geyser 25-50 ltrs all as per sample AC 230 Volts complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of flexible PVC connection pipe heavy duty suitable for hot water to bear the temp of 100 degree centigrade with outlet and inlet connection brass adopters , washers of size 450 mm long 15 mm dia bore complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of LED 7 watt pin type bulb complete all as specified and directed by Engineer-in-Charge. Make-Havells/Philips /Bajaj

Dismantling existing unserviceable hylam sheet of any size from boards removing switches etc. Supply and fix new hylam sheet 3mm thick including necessary cutting of suitable opening for switches, sockets, regulators, etc refixing of switches, sockets, regulators, etc replacing screws and connecting up and testing complete all as specified and directed by Engineer-in-Charge.

S&F in replacement LED Bulk head 7 watt, designed for modern homes available in non PIR as well as PIR sensor with premium quality diffuser for glare free light and easy to install snap fit installer with necessary connection of suitable size copper cable complete all as specified and directed by Engineer-in-Charge. Make : - Havells Cat part No LHEXCGP7IN5W006 or equivalent in Bajaj , CG

S&F PVC insulated and PVC Round Sheathed, Multi core Annealed Bare Copper Conductor (flexible) industrial cable for Voltage Grade 1100 Volt 3 x 1.0 sqmm drawn through pole from junction box to security light fitting complete all as specified and directed by Engineer-in-Charge.

Material & labour for earthing complete with galvanised cast iron earth plate electrode of size 600x600x6.0mm thick buried directly in ground less than 3.0m deep below normal ground level as earth electrode with top edge of the earth plate not less than 2.25mtr below ground level using GI strip 32x6 mm dia as earth continuity conductor connected to earth plate by means of welding, GI thimbles, nuts, bolts & washers all as directed including providing earth wire protection pipe GI light grade15mm dia from earth plate to main switch board/panel, watering pipe 20mm dia with wire mesh and funnel at top, earth pit and RCC pit cover with handle of angle iron frame of size 40 x 40 x 6mm in PCC 1:3:6 adequate quantity of charcoal dust and salt and kalmi shora all around the earth plate, earth work in any type of soil remaining surplus excavated material all as required at site and specified in EP No 3 of SSR part I 2009 complete all as specified and directed by Engineer-in-Charge including testing on completion. (i) Main earthing lead from earth plate electrode to test point up to length of 7.5 meters length shall deem to be included in the unit rate quoted against this item. (ii) GI protection pipe & earthing lead beyond 7.5 meter shall be measured and paid for separately under appropriate item of Sch A. (iii) On testing after completion if the desired resistance is not obtained the contractor shall redo the earthing without any extra cost to the department.

M/S A.N CONSTRUCTIONs (BID ID -3173248)

M/S Hilal Builders (BID ID -3173992)

BHAT CONSTRUCTIONS AND BUILFERS (BID ID -3173132)