CERTAIN SPL REP AND MINOR WORKS UNDER GE(AWC) MHOW.

Amount

Demolition of Concrete (Unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including old APP membrane complete all as specified and directed.

M&L 75mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) used as sub base under floor finishesfor laying interlocing blocks complete all as specified and directed.

M&LSand filling under floors or in foundations including watering and consolidation for interlocking paver block complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment complete all as specified and directed.

M & L PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in cills, steps, seismic and other similar bands, plinth courses, string courses, parapets and railing upto 60 cm in height, coping, kneelers, apex stones bed plates, etc and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary use and waste of form work complete all as specified.

M&L Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) in Foundations, including rafts, Plinth protection footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs,under-reamed piles and mass concrete complete all as specified and directed.

S&F Mild TMT steel bars 6-8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surface of concrete complete all as specified and directed.

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/loose soil each n exc 0.5 cu. m, getting out, complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, using Fe-410W (Gde-E-250) quality, complete all as specified and directed.

M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws as specified

M&L Preparation of newly or previously untreated steel surface of any description 10cm in width or girth,not otherwise described and applying two coat of synthetic enamel paint over a coat of primer complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), rubbish off the premises complete all as specified and directed.

M&L 15mm thick Screed bed or bedding layer of cement mortar 1:4 thick for laying floor finishes complete all as specified and directed.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting hard/dense soil all as specified and directed.

M&L Cement concrete1:4:8 type D2 (40mm graded aggregate ) in foundations, surface channel base filling and mass concrete complete.

M&L Cement concrete Type B1 (1:2:4) 40mm graded aggregate in surface channels and drains complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L Rendering 15mm thick in CM 1:4 (With WPC) on fair faces of brick work or concrete surfaces to maintain slope of the roof complete all as specified and directed. NOTE :- WPC shall be meausered and paid seperatly

Supply only Integral waterproofing compound, complete all as specified and directed.

M&L Water proofing treatment on "Non approachable / non accessible roof" surface (Horizontal & Vertical surfaces) in following sequence through authorized applicator of the manufacturer all as specified and directed complete. (i) M&L Priming surfaces and applyingn normal treatment (for moderate conditions) using glass fibre base bitumen felt, grade 2 complete all as specified and directed. (ii) M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. (iii) M&L Sealing surfaces previously treated with tar, bituminous composition, etc., with one coat of knotting in preparation for painting complete all as specified and directed. (iv) M&L Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coat of aluminium paint on APP memberane complete all as specified and directed.

M&L Brickwork with fly ash modular size bricks, straight or curved on plan exc 6m mean radius, built in C:M 1:4 Complete all as specified and directed.

M&L Brickwork with fly ash modular size bricks, straight or curved on plan to any radius in half brick thick walls, built in C:M 1:4 Complete all as specified and directed.

M&L RCC (Nominal Mix) Type B1, 1:2:4 (20mm graded aggregate I in Plinth Beams,Lintle beams cantilevers, bressummers, lintels over 1.5m span Complete all as specified and directed.

Use and Waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface of concrete complete all as specified and as directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L Hardcoreof broken bruck of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface for under sub base of floor, plinth protection complete all as specified and directed.

M&L 100mm thick sub-base Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) complete all as specified and directed.

M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick rendering in CM 1:4 to receive wall tiles complete all as specified and directed.

M&L Rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces to receive wall finishes complete all as specified and directed.

M&L Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces to maintain slope of the roof, surface finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of New surfaces of wall and applying two coat of white wash complete all as specified and directed.

M & l for preparation new surfaces and applying one coats of cement base paint with roller complete all as specified and directed.

M&L HDPE Double wall corrugated pipe 150mm bore laid and jointed complete with collars and bedding complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete.

Description same as per Item No. 39.00 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, complete all as specified and as directed.

M&L Cement concrete1:3:6 type C1 (20mm graded aggregate ) in Plinth Protection, filling and mass concrete complete all as specified and as directed.

S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm PVC (SWR) bends any radius complete all as specified and directed.

S&F 75 mm PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm PVC (SWR) vent cowl complete all as specified and directed.

S&F 75mmk PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 100mm PVC (SWR) 'P’ trap complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F 100mm dia Cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F 15mm steel Tubes, medium grade galvanised, with all fitting;laid in wall complete all as specified and directed.

S&F 20mm steel Tubes, medium grade galvanised, with all fitting;laid in wall complete all as specified and directed.

S&F 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertic with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to iron pipe complete all as specified and directed.

S&F Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding complete all as specified and directed.

S&F 10ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F Flush pipe/band of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed.

S&F Vitreous China wash basin, white, flat back, size 550x400mm excluding ditto but including brackets complete all as specified and directed.

S&F 15mm chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15mm chromium plated Pillar taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15mm fancy type Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed bothends for iron pipe or for unions and fixed complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour. Minimum weight 40gms complete all as specified and directed.

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

Sheet glass shelf/corner assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F 100mm Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F150mm long Aluminium anodised,barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 125mm long Aluminium handles, cast type, anodised complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, luminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

M & L extra for forming fair finished drain or channel 40 cm inner girth in cement concrete, using extra cement, incl forms, moulds mitred/stopped ends etc. complete all as specified and directed.

S & F Reinforced concrete pipes 300 mm bore, class NP2 , laid and jointed complete with collars, complete all as specified and directed.

M&L point wiring with 1.5 sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (FRLS)medium grade concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with and incl cast Iron / pressed steel modular terminal boxes any size/module, conceiled on walls and fixed by neans of brass screws incl modular cover plates and cover frme any size/module, for mounting or housing modular switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch complete all as specified and directed.

Description same as per Item No. 76.00 but for One 3 pin, 5/6 amps socket outlet point on independent board controlled by one, one way 5/6 amps switch

Description same as per Item No. 76.00 but for One 3 pin, 5/6 amps socket outlet point on same board controlled by one, one way 5/6 amps switch

M&L point wiring with 2.5 sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (FRLS) medium grade concealed in wall / ceiling with and including 2.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour)with cast Iron / pressed steel modular terminal boxes any size/module, fixed conceiled in walls by means of brass screws incl modular cover plates and cover frme any size/module, for housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for 15 / 16 Amps socket outlet on independent board, complete all as specified and directed.

S&F Ceiling rose three terminals surface bakelite type, AC, 50 HZ, 230V complete all as specified and directed.

S&F modular switch 1 way 6 A , 1 module complete all as specified and directed.

S&F modular socket 6 Amps 2/3 pin combined 2 module complete all as specified and directed.

S&F switch modular type 16 A, 1 module complete all as specified and directed.

S&F socket modular type multipurposes 6/16 A, 2 module complete all as specified and directed.

S&F surface /wall mounted LED batten (other than slim channel type) poly carbonate housing for retrofit LED tube T-8 type upto 1x22 watt, 4 feet long pre wired incl integrated electronic driver complete with all connected accessories all as specified and directed.

S&F ultra bright LED poly carbonate tube light 4 feet long 18 to 20 watts with THD less than 15% very high effficiency suited for T-8 tube light luminare with system efficiency 120 lumens per watts, fixture lumen package should be ≥ 2200 lumen. High quality polycarbonate end cap in white finish and snap fitted to the housing complete all as specified and directed.

S&F wall mounted 10 watts LED batten 2 feet long comprising extruded aluminium heat shrink provided for efficient heat dissipation & integrated electronic driver with aluminium housing system efficiency of 110 lumen per watt and lumen package ≥1100 lumen per watts, THD < 15% complete all as specified and directed.

M&L for LED Bulk head fitings of wattage 6 to 13 watts designed for modern homes available with premium quality diffuser for glarefree light and easy to install snapfit installer complete including taking down of old CFL/bulb bulk head fitting, making good of surfaces all as specified and directed.

S&F LED bldg security light fitting 30 watt incl GI pipe 40mm size (light grade) 1.2 mtrs length bend into size for fixing LED Light with saddle, screws incl provision of 3 core copper flexible wire from ceiling rose to connector of LED fitting made up of pressure die cast aluminium housing with acylic cover as diffuser with IP-65 and IK-07 protection, THD < 10% , lumen output ≥ 110 lumen per watt complete all as specified and directed.

Supply & Fix MCB SPN 40 Amps current rating 'C' series 10 KA breaking capacitycomplete all as specified and directed.

Supply & Fix MCB SP 6 to 32 Amps current rating 'C' series 10 KA breaking capacitycomplete all as specified and directed.

S&F Exhaust fan non metalic single phase 230 volt of size 250 mm sweep with louver all as specified and as directed.

S&F Exhaust fan , steel body AC single phase 230 volt of size 300 mm mm sweep complete with blade, frame and louvers all as specified and directed incl making/alteration of hole wherever necessary making good disturbed surface, painting to match with existing surfaces, complete all as specified and directed.

Replacement of Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level connect to galvanised earth lead wire of 4.0 sqmm size by means of bolts, nuts, check nuts and washers of galvanized iron or steel up to 7.5 meter length including connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber, 40 mm thick RCC cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150 mm c/c both ways etc complete all as shown in electrical plate No 3, connected to earthing test point complete including testing on completion all as specified.

Jamna Constructions

M/S Ashish Construction

Goyal Construction