15th finance Tied IInd Installment Improvement of Construction of Community Toilet Building work

Amount

Earthwork excavation in all soils and subsoils except hard rock requiring blasting with initial lead and lift as initial lead of 10.0 m and lift 0f 2.00 m including re-filling the sides of foundation in layer of 15cm. thick watering ramming depositing the surplus earth in the premises as directed by the departmental officers etc., complete complying with standard specification.

Plain Cement concrete 1:5:10 (One cement five sand and ten aggregate ) using 40mm ISS size hard broken granite metal for foundation and flooring including de-watering wherever necessary and laid in layers not more than 15cm. thick to required thickness , including cost and conveyance of materials to work site & labour charges complete with standard specifications

Supplying and filling well gravel in layers of not more than 15 cm thick well watered rammed and con-solidated etc., complying with standard specifications

Brick work In CM 1:5 mix using best country bricks of size 83/4x41/4x23/4 having 350kg/cm2 compressive strength and 15% or less water absorbentin the period of 24hours immersement and confirming to ISI specifications.and using the screened sand and all the materials should be approved by the competent technical authorities etc complete complying with standard specification.

Supplying and erecting centering to sides and soffits including supports and strutting for drainage sides and culvert body wall sides using 90cm x 60cm and B.G 10stifened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding laid over (silver oak joists ) of size 10cm x 6.50cm spread at about 90cm etc. complete complying with standard specification .

Supplying, fabricating and placing in position of Steel Reinforcement using Mild steel or Ribbed tor steel rods, for all RCC works as per the design given by the departmental officers including cost of steel and binding wire and all labour charges for cutting, bending, tying and placing in position etc,complete as per SS.

Reinforced cement concrete in 1:1½:3 [one cement and one and half sand and four the aggregate ] using 20 mm size IRC grade machine crushed chips and excluding cost of reinforcement and centering works and including the cost of mixing, laying , curing etc.,complete complying with standard specification .

Plain Cement concrete 1 : 2 : 4 (one cement, two sand and four aggregates) using 20mm ISS HBG metal including cost and conveyance of all materials and labour charges for mixing, laying, compacting and curing etc, complete as per SS

Plastering in cement mortar 1:3 mix 10mm thick using clean screened sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting for plastering for plastering and protecting from other damages till setting of mortar etc.complete complying with standard specification

Plastering with CM 1:5 (One cement and Five sand) mix 12 mm thick including finishing cost and conveyance of all materials to work site and all labour charges watering, curing and and all other incidental charges etc., complete complying with standard specifications.

Dadooing the wall glazed tiles of size 305mm x 200mm x 6mm size of approved make and quality and colour 1set in cement mortor 1:2 (one cement and two sand) over 10mm base layer plastering and pointing with white cement neatly as directed.

Paving the floor with plain/design Antiskirt ceramic tiles (colour shade as directed) of size 305mm x 305mm x 6mm in all floors over a base layer of cement mortor 1:3 (one cement and three sand) 20mm thick laid in-situ and pointed with same coloured cement

Supplying and fixing in position best white glazed earthenware INDIAN WATER CLOSET with "P" and "S" trap with double flapped sheet cover with brace hinges and 10 Liter capavity PVC low level flushing tank with all internal fittings in position with 40mm brick jelly concrete 1:2:5 mix (one lime, two sand and five brick jelly) and finishing the top with a required slope and incluiding giving connection to the AC soil straks by dismantling the masonry floor or RCC works and rejoining the same to the original condition without any leakage etc., complete as directed by the departmental officers.

Fabricating, supplying and fixing in positon of SOLID PVC DOORS with frames of different sizes as per the specifications given below: PVC door frames made out of best quality PVC extruded section of 40mm * 58 mm * 2.50 mm +/- 0.3 mm thick, having multichamber cross section and duly reinforced with steel to be mitre cut at the corners and welded including providing tie rod at the bottom and necessary weather seal etc., and PVC door shutters made out of extruded plastic section of 60 mm * 24 mm size in the configruation of an "A" section for shutter frames and multi-chamber hollow plastic section of 200 mm *200 mm*1 mm (average thickness) with tongue and groove section for panels etc., with necessary holdfasts, rubber beedings, furniture fittings, locking arrangements etc., complete including dimantling the masnery, making chippings, holes in the RCC column, beam etc., wherever necessary with power drill to the extent required and redoing the same to the original condition after fixing etc., complete as per specifications and as directed by the departmental officers.

LOUVERED VENTILATOR Supplying fabricating and fixing in position of Alumi,Anodised natural colour matt finished LOUVERED VENTILATOR fixed window with three panels using 62*38*[email protected]/m and the louvers with moving arrangement will be made with Aluminium channel of size 60*30*4 mm @ 1.27kg/m with necessary glass panes for louvers 4mm thick Aluminium clips , including all materials,labour,power consumption charges required for fabrication if necessary chipping dismantling making necessary holes in RCC coloumns, Beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as drected by the departmental officers The Aluminium surfaces should be anodised with matt finish under electrically condition in accordance with IS specification 1868/1962 of Anodic thickness of not less than 15 microns (fifteen) complete. All the materials should be got approved by the Engineer incharge before fixing as directed.

Supply and delivery and fixing of HDPE tank including loading and unloading, transportation fixing and necessary GI pipe and specials for pipe connection works including cutting, threading and fixing charges as directed by departmental officers etc., complete

Supply and delivery of GI specials confirming to ISI Specifications

20mm GI Bend

32mm Gi Pipe

32m. GM gate valve

32mm GI Coupling (Heavy duty)

32mm Elbow

20mm GI Pipe

20mm GI Coupling (Heavy duty)

20mm GI Bend

20mm pvc pipe

32mm pvc pipe

Wiring with 2x1.5 Sq.mm (22/0.3) PVC insulated SC .unsheathed cu.conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box and 5 Amps F.T switch with painting of suitable colour for open PVC light point/ Fan point (For Electronic Regulator)6 point per coil)SD No 20

Painting two coats with approved emulsun cement paint over one priming coat of cement paint over cement plastered New Wall surface and ceiling including cost of one priming coat, Cost of all materials, all labour charges, brushes etc, complete as per Standard Specification

P.S. Constructions