Construction of Working Women Hostel for 100 working women at Dr. YSP UHF Nauni- Solan SH Co Working Women Hostel Phase -1 for 60 Women Site Development, building portion ,water suplly and sanitary installation

Amount

Excavation in ordinary rock in hilly/ Valley area by mechanical means including cutting and trimming of side slopes and disposing of excavated earth upto all leads, lifts and carriage of material as directed by the Engineer-in-Charge.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas in all width and depth on plan) including getting out and disposal of excavated earth all leads, lifts and carriage of material as directed by the Engineer-in-charge .a). Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains in all width , including dressing of sides and ramming of bottoms, in all lift including getting out the excavated soil and disposal of surplus excavated soil complete in all leads, lifts and carriage of material as directed by the Engineer-in- Charge. a) Ordinary rock

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying in plain cement concrete 1:8:16 (one cement: eight sand: sixteen graded stone aggregate 20mm (twenty milimetre) and curing complete on slab and floor excluding the cost of centering and shuttering screed laid under flooring etc. complete in all respect as per satisfaction of Engineer-in-Charge

Providing and laying in plain cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level etc. complete in all respect as per satisfaction of Engineer-in-Charge .a). 1:5:10 (One cement : five sand : ten graded stone aggregate 40 mm ( forty milimetre nominal size).

Making plinth protection 50mm (fifty milimetre) thick of cement concrete 1:3:6 (one cement : three sand: six graded stone aggregate 20 mm (twenty milimetre) nominal size) over 75mm (seventy five milimetre) thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth etc. complete in all respect as per satisfaction of Engineer-in-Charge..

Providing and applying a coat of Residual petroleum bitumen of grade of VG-10 of Approved quality using 1.7 kg sqaure metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement work up to plinth level with 1.1.5:3 (one cement : one and half sand : three stone aggregate 20 mm (Twenty milimetre) nominal size) in foundation and plinth etc. Complete in all respect as per satisfaction of Engineer-in-charge.(M-25 GRADE)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. Above plinth level up to all floor level with 1:1.5:3(one cement: one and half sand: three stone aggregate 20 mm (Twenty milimetre) nominal size) excluding cost of shuttering, finishing and reinforcement etc. Complete in all respect as per satisfaction of Engineer-in-charge.(M-25 GRADE)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all floor level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : oneand half sand : three graded stone aggregate 20 mm(twenty milimetre) nominal size) etc. complete in all respect as per satisfaction of Engineer-in-Charge.(M-25 GRADE)

Centering and shuttering including strutting, propping etc. and removal of form for etc. complete in all respect as per satisfaction of Engineer-in-charge.

Foundations, footings, bases of columns, etc. for mass

Suspended floors, roofs, landings, balconies and access platform. c). Lintels, beams, plinth beams, girders, bressurmers and cantilevers

Lintels, beams, plinth beams, girders, bressurmers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth level with Cement mortar 1:6 (one cement : six sand) complete in all respect as per satisfaction of Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level with cement mortar 1:6 (one cement : Six sand) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Brick work with common burnt clay machine moulded F.P.S. (non modular) bricks of class designation 12.5 in exposed brick work in super structure above plinth level up to all floor level including making horizontal and vertical grooves 10mm wide 12 mm deep complete in cement motar 1:6 )one cement :six sand ) etc. complete in all respect as satisfaction of Engineer -in-charge

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level with cement mortar 1:4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Brick edging 7 cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (one cement : four sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Square rubble masonary coursed with hard stone of approved quality in foundation and plinth in retaining/breast wall including rackout joints in cement mortar 1:6 )one cement: six sand) complete in all respect as per satisfaction of Engineer-in -Charge

Square rubble masonary coursed with hard stone of approved quality in foundation and plinth in retaining/breast wall including rackout joints in laid dry etc. complete in all respect as per satisfaction of Engineer-in -Charge

Stone filling behind retaining wall including all leads ,lifts and carriage of materials etc. complete in all respect as per specification of Engineer-in -charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete in all levels etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). Granite of any colour and shade Area of slab over 0.50 sqm

Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. a) Granite work

Providing and fixing jointless Ist quality ceramic glazed wall tiles (Kazaria / Oreint bell / Nitco/ Somany make) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete in all respact as per direction of Engineer-in- Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length etc. complete in all respect as per satisfaction of Engineer-in-Charge. ( hold fast lugs or dash fastener shall be paid for separately. a).Sal wood

Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, etc. complete as per direction of Engineer-incharge. (Note:- Butt hinges and necessary screws shall be paid separately) a) Second class teak wood.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 30 mm ( Thirty milimetre) thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) etc. complete as per direction of Engineer-incharge. Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick

a). Second class teak wood

b). Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size etc. complete in all respect as per satisfaction of Engineer-in-charge. a) Second class teak wood

Providing and fixing 2nd class teak wood 50mm into 12 mm wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 25 mm dia heavy type Nickel plated M.S. pipe curtain rods with nickel plated brackets etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

Providing and fixing150 mm ISI marked oxidized/chromium plated M.S single acting spring hings with necessary screws etc. complete in all respect as per satisfication of engineer-in -charge.

Providing and fixing aluminum sliding door bolts, ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 300x16 mm (three hundred into sixteen milimetre)

b). 250x16mm(two hundred fifty into sixteen milimetre)

Providing and fixing aluminum tower bolts, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge

a). 200x10 mm(two hundred into ten milimetre)

Providing and fixing aluminum handles, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

a). 125mm(One hundred twenty five milimetre)

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-charge. (Single Rubber Stopper)

Providing and fixing ISI marked 85x42 mm oxidized M.S pull bolt lock conforming to IS :7534 with necessary screws bolts,nuts and washers etc complete in all respect as per satisfaction of Engineer-in -Chrage.

Providing and fixing ISI Marked M.S pressed butt hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in -Charge

Providing and fixing factory made UPVC white colour fixed glazed windows/ Ventilators comprising of UPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), , UPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary Stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded Including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be Paid separately. a). Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made UPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of UPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile), appropriate dimension of UPVC extruded glazing beads and UPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and Necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon silent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon silent shall be paid separately) a). Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Providing and fixing Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture for UPVC three track shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). UPVC three track 25 mm to 40 mm thick: etc. complete in all respect as satisfaction of Engineer-in- Charge (EPDM gasket and beading will be paid for separately).

Providing and fixing 4mm thick glass pane (weight not less than 10 Kg per Sqm) for UPVC three track shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). UPVC three track 25 mm to 40 mm thick: etc. complete in all respect as satisfaction of Engineer-in- Charge (EPDM gasket and beading will be paid for separately). .

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Structural steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using tube etc. as required complete in all respect as per satisfaction of Engineer-in-Charge. a). In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing angle iron frames for doors,windows and ventilators of mild steel Angle sections of size 35x35x5 mm joints mitred and welded by the angle iron 35x35x5 mm or 35x5mm flat pieces to the existing T-iron frame or to the wall with dash fastener ,including fixing of necessary butt hinges and scewss and applying a printing coat of approved steel primer , all complete as per the direction of Engineer-in charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying Glossy vitrified floor tiles double charged in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, (Kazaria/ Nitco/ Orient bell/ Somany make), in all colors and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ Sqm including grouting the joints with white cement and matching pigments etc., complete in all respect as per satisfaction of Engineer-in-Charge. a). Size of tile 600x600mm

Providing and laying JointlessCeramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc complete in all respect as per satisfaction of Engineer-in-Charge (Kazaria / Nitco / Oreintbell / Somanymake).

Grouting the joints of flooring Kota/tiles 300 X300mm size having joints of 3 mm width in different size of tiles/ Kota stone, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing etc. complete as per the satisfaction of Engineer-in-charge.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. a). Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge(Tata/ Jindal/ JSW make).

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws etc. complete in all respect as per satisfaction of Engineer-in-Charge (Tata/ Jindel/ JSW make)

a). Ridges plain (500 - 600mm)

b). Barge board (Upto 300 mm)

c)Guttter 600 mm overall girth

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-Charge. (i) Single socketed pipes a). 110 mm ( One hundred ten milimetre) diameter

Providing and fixing unplasticised – PVC moulded fittings/ accessories for unplasticised PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). Coupler 110 mm (One hundred ten milimetre) diameter

b). Bend 87.5* Bend 110 mm (One hundred ten milimetre) diameter

Providing and fixing unplasticised – PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50 mm hard wood plugs screwed with MS screws of required length including cutting brick/ RCC work and fixing in cement mortar 1:4 ( one cement; four sand) and making good the wall etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 110 mm (one hundred ten milimetre) diameter.

6 mm (six milimetre) thick ceiling plaster with cement mortar 1:3 (one Cement: three sand) complete in all respect as per satisfaction of Engineer-in-Charge.

15 mm (fifteen milimetre thick) cement plaster on rough side of single or half brick wall of mix with cement mortar 1:6 (one cement: six sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint on steel/ wood work of approved brand and manufacture to give an even shade etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Two or more coats on new work.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade etc. all complete as specified and as directed by the Engineer-in-Charge a)Two or more coats on new work

Providing and applying white cement based putty of average thickness one mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete etc. in all respect as per satisfaction of Engineer-in-Charge.

Finishing walls with Acrylic Smooth exterior paint of required shade with New work (Two or more coat applied @ 1.67 ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 Sqm) etc. in all respect as per satisfaction of Engineer-in-Charge.

French spirit polishing two or more coats on new works as required etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extrasand Complete all as per direction of Engineer-in-Charge (ISI Marked). a) 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete in all respect as per satisfaction of Engineer-in-Charge (Cera/ Hindware/ Jaquar make). a) W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete in all respect as per satisfaction of Engineer-in-Charge (Cera / Hindware make). a)White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge a). 610x510 mm bowl depth 200mm

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto one metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing 32mm dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing G.I. Pipes medium grade complete with G.I. fittings and clamps, i/c making good the walls etc. Concealed etc. complete in all respect as per satisfaction of Engineer-in-charge. (Jindal / Surya make).

a). 15 mm (fifteen milimetre) dia nominal bore

b). 20 mm( twenty milimetre) dia nominal bore .

Providing and fixing G.I. Pipes medium grade complete with G.I. fittings and including trenching and refilling etc. complete in all respect as per satisfaction of engineer -in-Charge (Jindal/surya make) 20mm (twenty mm dia nominal bore)

Providing and fixing 20 mm (twenty milimetre) nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 45 cm length and 15 mm nominal dia uplasticised PVC connection pipe with brass unions complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 Sintex marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge (Sparton/ Seiko/ smile/ Czar make).

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge (Seiko/ smile/ sparton/ zar make).

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 complete in all respect as per satisfaction of Engineer-in-Charge (Sparton/ Seiko/ smile/ Czar make).

Cutting holes up to 30x30 cm in walls including making good the same with common burnt clay F.P.S. (non modular) bricks complete in all respect as per satisfaction of Engineer-in-Charge.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (one cement: two sand: four graded stone aggregate 20 mm (twenty milimetre) nominal size including finishing complete so as to make it leak proof etc. complete in all respect as per satisfaction of Engineer-in-Charge..

Extra for depth for manholes with common burnt clay FPS (non- Modular) bricks of class designation 7.5 etc. complete in all respect as per satisfaction ofEengineer-in-charge

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one & half coarse sand (zone- III) : three graded stone aggregate 20 mm(twenty milimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm(forty milimetre) nominal size), inside plastering 12 mm thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement :two coarse sand : four graded stone aggregate 20 mm(twenty milimetre) nominal size) finished with a floating coat of neat cement complete as per standard design complete in all respect as per satisfaction of Engineer-in-Charge. a). Inside size 900x800mm and 450mm deep including 450x610mm and 50 mm thick rectangular opening SFRC Man hole cover with frame. ) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing and fixing C.P. brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. brass complete in all respect as per satisfaction of Engineer-in-charge a). 600x20mm size

Providing and fixing 100mm dia chromium plated grating of superior quality for floor, gully or nahani trap complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Kisan / D-Plast make).a) 110mmx75mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/ Kisan/ D-plast/ Prayag make).

a). 75mm (Seventy five milimetre) dia

b). 110mm ( One hundred ten milimetre) dia

c). 150mm ( One hundred ten milimetre) dia

Providing and fixing PVC single equal branch with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast/Prayag make).

a). 75mm (Seventy five milimetre ) dia

b). 110mm ( one hundred ten milimetre) dia

Providing and fixing PVC single equal branch plain ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast /Prayag make).

a). 75mm (Seventy five milimetre) dia

b). 110mm ( one hundred ten milimetre) dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast/ Prayag make).

a) 75mm (Seventy five milimetre ) dia

b) 110mm ( one hundred ten milimetre) dia

b) 150mm ( one hundred fifty milimetre) dia

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five milimetre )dia

b). 110 mm ( one hundred ten milimetre) dia

Providing and fixing PVC door bend with oval access door insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc complete in all respect as pcomplete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five milimetre )dia

b). 110mm ( one hundred ten milimetre) dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm (Seventy five milimetre )dia

b). 110mm ( one hundred ten milimetre) dia

Providing and fixing 25 mm (Twenty five mm ) thick factory made shutter of prelaminated HDHMR ( high density high mositure resistance ) board both side decorative finish confirming to IS -12406 grade of approved design including fixing of heavy MS hinges 4" long etc complete as per architectural drawing and direction od engineer -in- charge( cost of hinges will be paid for seperatly )

Providing and fixing 12 mm thick imported pine wood paneling/lining & ceiling with tongued and grooved jointing and wooden screws etc. complete in all respect as per satisfaction of Engineer-in- Charge (Frame work to be measured and paid for separately).

Providing and fixing PVC gully trap with grating brick masonry chamber in cement mortar 1:5 and water tight CI cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53 kg. and frame to be not less than 2.72 kg. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

Providing and fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).

a). 75mm dia (seventy five milimetre)

b). 110mm dia (one hundred ten milimetre)

Vidya Infrastructure and Developers (BID ID -538825)

Jia Lal Chauhan (BID ID -538745)