REPAIRS TO FLOORS, SUNKEN FLOORS, SANITARY FITTINGS, PLUMBING, STROM WATER DRAINS, COMPOUND WALL, FENCEING AND HARD STANDINGS AT MADUKKARAI AND COIMBATORE ARMY AREA UNDER AGE (I) COIMBATORE.

Amount

S&F in repairs Health faucet (Jet Spray), CP, 15mm bore with flexible pipe and fixing nut etc complete all as specified and as directed.

S&F in repairs PVC valve less, syphonic action type flushing cistern, low level, 10 litres capacity, white, with inlet, ball, valve, float and handle including brackets complete all as specified and as directed.

S&F in repairs Stainless steel sinks with drainage board 1mm thick with plugs, washers and waste; including bedding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe, overall size 915 mm x 460 mm, bowl size 410 x 330 x 160mm complete all as specified and as directed.

S&F in repairs Chromium plated shower rose with or without swivel joint,100 to 125 mm size, including fixing to steel pipe or union complete all as specified and as directed.

S&F in repairs vitreous china wash basin, white, flat back, size 550 x 400 mm including brackets complete all as specified and as directed.

S&F in repairs vitreous china wash basin, white, flat back, size 450 x 300 mm including brackets complete all as specified and as directed.

S&F in repairs Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), P trap/S trap etc complete all as specified and as directed..

S&F in repairs Vitreous China Wash down water closet pan (Pedestal pattern), white (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repairs 15 mm dia bore bib taps of cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs 15 mm dia bore bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm-125gms). complete all as specified and as directed.

S&F in repairs Pillar taps, fancy type, 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs 15mm bore Pillar taps, of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-110gms) complete all as specified and as directed.

S&F in repairs Stop/angle valves, 15mm dia, fancy type chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs Stop/angle valves, 15mm dia for shower rose, fancy type chromium plated cast copper alloy, with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs 20mm dia Gunmetal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed

S&F in repairs 32/40mm dia expandable type PTMT waste pipe for Wash hand basin/kitchen sink complete all as specified and directed.

S&F in repairs 25mm dia Gunmetal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S&F in repairs 15mm dia chromium plated cast copper alloy fancy type, two in one combination of bib tap and angle valve fixed all as directed.

Taking up or down steel tubing and connections, bore of pipe 15 mm and remove from site complete all as specified and as directed.

S&F 15mm Unplasticised PVC pipes of pressure rating 10 kgf/cm2 laid and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

Taking up or down steel tubing and connections, bore of pipe 20 mm and remove from site complete all as specified and as directed.

S&F 20mm Unplasticised PVC pipes of pressure rating 10 kgf/cm2 laid and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Taking up or down steel tubing and connections, bore of pipe 40 mm and remove from site complete all as specified and as directed.

S&F 40mm Unplasticised PVC pipes of pressure rating 10 kgf/cm2 laid and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Dismantling water tanks capacity exceeding 250 ltrs & not exceeding 500 ltrs complete all as specified and as directed.

Dismantling water tanks capacity exceeding 500 ltrs and not exceeding 1000 ltrs complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tanks, ISI marked (cylindrical vertical with closed top) hoisted and fixed in position, 500 ltrs capacity complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank, ISI marked of capacity 1000 ltrs hoisted and fixed in position complete all as specified and as directed.

S&F in repairs PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs PVC (SWR) 75mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

Demolition of wall and ceiling boards (fiber pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

M&L False ceiling using GI snap grid system with roll-formed out of hot-dip galvanised steel capping (powder coated), main runner 38x24mm, cross Tee 29x24mm and wall angle 24x24mm and thickness not less than 1 mm, members suspended with Hangers 4 mm dia. G.I. (up to 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long , with 4mm thick designer ceiling board of any texture (Lake & hill, Oceanic, cascade or Electra) as approved by GE, all as per Everest Ceiling grid system "Regular T-2430" or its equivalent complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in CM 1:6 complete all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L 15mm thick rendering on brick wall/ concrete surfaces in CM 1:6 finished even and smooth without using extra cement all as directed.

M&L Preparation of newly plastered surfaces of walls and applying Three coats of white wash complete all as specified and as directed.

M&L Complete removal of old treatment of wall surfaces and applying two coats of oil bound distemper over a coat of wall care putty and a coat of priming paint complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) all as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed.

M&L Sunken floor treatment by providing injection pressure grouting treatment using cement slurry mixed with grout admixtures non shrink additive using 40 PSI pump complete and applying two coats of brush bond acrylic polymer modified cement based coating thickness 1mm or two coats of pidifin 2K acrylic polymer water proof coating including necessary surface preparation, providing 20 mm thick water proofing screed bed /plaster in CM 1:4 mixed with conplast x 42 IC @ 100ml or Pidiproof LW @ 200ml per bag cement. Two coats of Nitro proof 100 bitumen based water proofing over plastered surface complete all as per specification of chemical resistant coating complete all as specified and as directed by Engineer in Charge. Note: The work shall be executed through authorised applicator of M/s FOSROC/Pidilite using the materials supplied by M/s Fosroc chemicals India Pvt ltd or M/s Pidilite industrial Ltd and in accordance with their respective manufacturers instructions.

M&L 300mm thick lime concrete with lime mortar 1:3 mix and 40 mm graded brick coarse aggregate in sub-floors complete all as specified and as directed.

M&L Screed bed or bedding layer of CM 1:6, 15 mm thick for laying floor finishes complete all as specified and directed.

M&L White coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L White glazed ceramic tiles (300x200) x 6-7mm thick, as in skirting/ dado set and jointed in neat cement slurry and pointed in coloured cement to match colour of the tile complete all as specified and directed.

M&L 25mm thick cement concrete1:2:4, type B1 using 20mm graded stone aggregate as in sub floor, sub bases, floors and pavings etc complete all as specified and directed.

M&L Backing coat/screed 10mm thick in CM 1:4 on fair faces of brick/ stone wall surfaces complete all as specified and directed.

S&F Cast iron floor trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete1:2:4, type B-1 using 20mm graded stone aggregate complete all as specified and directed.

S&F Cast iron nahani trap 75 mm dia with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 using 20mm graded stone aggregate complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof covering complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain sheet 0.45 mm to 0.50 mm thick of any colour having tensile strength 550 mpa as in ridges, fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

S&F Rolled mild steel work in purlins, rafters, roof truss etc including cleats/distance pieces etc complete, conforming to Fe-410 W (Gde-E-250) Quality A complete all as specified and directed.

S&F Rolled Mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

Demolition of brick work or stone/boulder/block masonry built in cement mortar, including all quoins, arches, pillars, etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors not exceeding 15 cm thickness ( below or above ground level) complete all as specified and directed.

M&L for PCC 1:3:6, type C2 using 40mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

M&L Pre-cast cement concrete block masonry with solid blocks of CC 1:3:6, type C1 using 20 mm graded stone aggregates, exceeding 10 cm in width and setting in cement mortar 1:4 complete all as specified and directed.

M&L Rendering 15 mm thick in cm 1:4 on fair faces of brick or concrete surfaces finished even and smooth with out using extra cement complete all as specified and directed.

M&L Cement concrete 1:2:4, type B1 using 20mm graded stone aggregate as in benching/copings complete all as specified and directed.

S&F Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as directed.

M&L Precast cement concrete 1:2:4, type B1 using 20mm graded stone aggregate, set in CM 1:4 as in cover slabs complete all as specified and directed.

M&L 100mm thick Hard core using broken stone, broken to gauge not exceeding 63 mm spread levelled complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection/path laid and finished in bays not exceeding 3 m c/c and filling the joints with mastic bitumen complete all as specified and directed.

M&L 100mm thick Cement concrete, 1:4:8, type D-2, using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M&L Chequerred cement concrete tiles with grey cement and pigment of size 300x300mm x 25mm thick set, jointed and pointed in neat cement slurry including 15mm thick bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment including finishing the outer edge with cement concrete 1:2:4 using 20 mm graded aggregate complete all as specified and directed.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

p.chinnasamy

SKM CONSTRUCTION