providing interior arrangements forTAEI building in WBD

Providing and fixing of Armstrong orcal Clip in Plain 7 brush finish Stainless steel false ceiling system consisting of 3.80 x 1.2 m clip tiles of Stainless Steel in 0.5 mm thickness with bevel edge in white colour (RAL 9010) with light reflectance > 60% and suitable for green building application, with recycled content of 25 % Installation: To comprise 300 mm long "C" channels spaced at 1200 mm centre's securely fixing to the structural soffit by support clamp and approved hangers. The last hangers at the end each C channel should not be greater than 600 mm from the adjacent wall use a C channel connector for splicing two pieces of C channels 4000 mm Dp-12 main carriers (Spring tee bars) shall be spaced at 600 mm centre's in a direction perpendicular to the C- Channels and shall be secured at every intersection with C channels using a dp-12 hanger. Tiles should be clipped in between two Dp-12 carriers (Spring tee bars) from below. perimeter trims to be of Armstrong wall angles of white colour secured to walls at 450 mm maximum centres. Cut tiles to be secured to the wall angle using a spring clamp.

Suppling fabricating, erecting and fixing of stainless steel passbox etc., complete

Supplying and fixing of SS Sink of size 1200 x 550 x 180mm

Supply and application of Epoxy resin based floor topping of good quality and approved variety over the primer prior application mix mechanically the two components using heavy duty driling machine until achiving a homogenous mix and spread on the prepared area using serrated notch, travel for a thickness of 3mm. spike roller shall be rolled over to remove the entrapped air. (Total system thickness 3mm Epoxy flooring) etc. complete complying with standard specification and as directed by the departmental officers. The rate is inclusive of all materials. labour charges transportation and all other incidental charges.

Providing and fixing of 1.2mm thick Lead Lining Door for X-Ray Rooms, Scanning Rooms with Mild Steel Door Frames 105mm x 57mm X 18 G and 12 G x 50mm Shutter made of GI with PWG finish and honey wool insulations with SS 101mm x 75mm x 3mm SS 304 Ball Bearings Butt Hinges, Mortice Sash Lock ML 100A, 50mm BS, 85mm centre, CL 207 : Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make), Heavy Duty Door Closer, Frames fixed wih walls using Mortice Sash Lock ML 100A, 50mm BS, 85mm centre CL207: Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make) all neccesary accessories and fittings as per the required and as per the approval for the Department Officer

Supplying fabricating erecting and fixing GYP board false ceiling up to a ceiling height of 4.50m from floor level using Hilux Board plain sheets 10mm thick which includes shaped GI channels of size 25 x 25 x 0.50mm thick suspended from ceiling at 1.2 m both longitudinal and cross vertical support and fixing shaped GI channels of size 50 x 30 x 0.50 mm and 150 x 10 x 0.50 mm thick at 0.60m centre longitudinal and cross direction for vertical supports and fixing U shaped GI channels of size 50 x 30 x 0.50 mm thick and 50 x 10 x 0.50 mm thick at 0.60 m centre to centre in cross direction respectively forhorizontal supports of zig - zag pattern and fixing of Gyp board in the panel provided in the design pattern given and asper the standard specification and as directed by the departmental officers. The rate shall be inclusive of finishing the edges and wall junctions with suitable lipping etc., complete complying with standard specification and as directed by the departmental officers.

Fabricating and fixing for Form board with name board stickers including cost of labour for scaffolding charges etc complete

Supply, installation, testing and commissioning of Reciprocating Air Cooled Type (10 HP) Rating Vaccum Pump as per following provisions. As per IS 12827 / 1987 & ISO 7396 / 1987 Specification a) Vaccum Pump - 10 HP - 1 No. b) Electric Motor - 10 HP - 1 No. c) DOL Starter with OLR - 1 No. d) Vaccum Switch - 1 No. e) Vaccum Gauge - 1 No. f) Control Frame with Fittings - 1 No. g) Suction Scrubber - 1 No. h) V-Belts - 1 No. i) GI & MS Fittings - 1 No. j) Brass Fittings - 1 No. k) Exhaust Silencer - 1 No. i) Base Frame for Motor and Vaccum Pump - 1 set m) Pilot Line with Fittings - 1 set, Vaccum Room & Air Compressor Room Inside

Supply, installation, testing and commissioning of Compressed Air System of Reciprocating Oil Free Air Compressor Belt Driven Type 10 HP Air Compressor with following provisions. As per IS 12827 / 1987 & ISO 7396 / 1987 Specification Compressor package consists of following: a) 10 HP Air Compressor - 1 No. b) Electric Motor 10 HP - 1 No. c) Dol Starter - L&T - 10 HP - 1 No. d) Base Frame Kit (for Motor and Compressor) - 1 set e) Pressure Swith - 1 No. f) Pressure Gauge - 1 No. g) NRV and Pilot Fittings - 1 No. h) Delivery Tube - 1 No i) Foundation Bolts & Anchor Fasteners - 1 Lot j) Belt Guard - 1 No. k) Refrigerator Type Air Dryer-40 cfm. capacity-1 No. l) Drain Ball Valve - 1 No. m) Air Outlet Ball Valve - 1 No. Vacuum Room & Air Compressor Room Inside Accessories: Non-Return Valves, Air Pressure Switch, Pressure Gauge, Isolation Valves, Air Filters etc., Inter connecting piping: Mild Steel Pipe of 2 with fittings.

GST @ 18 %