REPAIR/REPLACEMENT OF WORN OUT PARTS AND PAINTING/POLISHING OF STEEL AND WOODEN FURNITURE, RECANNING OF CHAIR AT JINDRAH AND DHANSAL UNDER GE (ARMY) DHAR ROAD

Amount

Taking down worned out/unsv components of the following wooden furniture items, S&F new component without any crack/any defects as per shape and size specified on respective drawings and as directed by Engineer-in-charge

BED PLY WOOD TOP (FD 246/247)

Head rest as shown on drawing

Foot Rest as shown on drawing

Long rail made of Ist class hard wood

Short rail made of Ist class hard wood

Stiffener made of Ist class hard wood

Right angled MS bracket 200mm long x 25mm wide x 3mm thick duly fixed with screw

12mm thick BWR Ply wood top in one piece

CHAIR DINING (FD-203/279)

Rear Leg

Front Leg

Side rail with holes for weaving (spacing of holes shall be as per old one)

Front/back rail with holes for weaving (spacing of holes shall be as per old one)

Bottom stiffener

Back stiffener

Provn of four Nos of wooden tringular bracket of size 75mm x 75mm to each chair made out 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

CHAIR WRITING (FD-261/280)

Rear legs

Front Legs

Side rail with holes for weaving (spacing of holes shall be as per old one)

Front/back rail with holes for weaving (spacing of holes shall be as per old one)

Bottom stiffener

Back stiffener

Arm rest

Provn of four Nos of wooden tringular bracket of size 75mm x 75mm to each chair made out 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

CHAIR DINING OFFICERS (FD/E6/MAP/10 & FD/E6/MAP/10 (R)

Rear Leg

Front Legs

Side rail of seat frame

Front/back rails of seat frame

Seat made out of 75mm foam cushioned of 40 density covered with tapestry cloth fabric not less than Rs 200/- per RM as approved by Engr-in-Charge

Bottom stiffener

Vertical back stiffener

Provn of four Nos of wooden tringular bracket of size 75mm x 75mm to each chair made out 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

CHAIR EASY(FD-229) -

Rear Leg

Front Leg

Side Rail

Front/Back Rail

Back Stiffener

Bottom Stiffner

Arms rest

PVC/Rubber Shoe as per sample approved

TEAPOY (FD-278/382)

Long rail

Short rail

Side stiffener

Centre stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

Provn of eight Nos of wooden tringular bracket of size 75mm x 75mm to each teapoy made out 30mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PEG TABLE (FD-236/277/384)

Long rail

Short rail

Side stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

TABLE WRITING (FD-275)

Long rail

Short rail

Drawer made out prelaminated MDF board and 6mm thick commercial ply at bottom and fitted with one 100mm chromium plated handle

Bottom centre stiffener

Bottom side stiffener.

Provn of six Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

TABLE 900mm x 600mm WITH DRAWER and WITHOUT DRAWER (FD-283/284)

Long Rail

Short Rail

Bottom Side stiffener

Bottom Centre stiffener

Drawer made out prelaminated MDF board and 6mm thick commercial ply at bottom and fitted with one 100mm chromium plated handle

Provn of six Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 25mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

Table Office Clerk wooden

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

TABLE DINING 06 PERSON( FD-239/273)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Long rail

Short rail

Stiffener

Provn of eight Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 40mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

TABLE DRESSING LADIES (FD-251/378/395)

5mm thick Mirror of size 365mmx1220mm of approved brand with Back ply of 6mm thick commercial plywood and wooden frame of existing shape & size

Sliding glass shutter of 3mm thick as per existing.

Drawer of 6 mm thick ply wood commercial with 18mm pre-laminated MDF board as per existing shape and size

TABLE DINING 08 PERSON( FD-239/273)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Long rail

Short rail

Stiffener

Provn of eight Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 40mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

SIDE BOARD (FD-241/371)

Bottom

Drawer of 6 mm thick ply wood commercial with 18mm pre-laminated MDF board as per existing shape and size

Shutter made of 18mm thick prelaminated MDF Board with hinges

Back shall be made of 6mm thick commercial plywood.

Bottom frame with 4 Nos of legs shall be made of Ist class hard wood

Knob as per sample approved

TABLE CENTRE (FD-274/375)

Long rail

Short rail

Side stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

PVC/Rubber Shoe as per sample approved

TABLE 900mm x 900mm (FD-291)

Long rail

Short rail

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Provn of eight Nos of wooden tringular bracket of size 75mm x 75mm to each Table made out of 35mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

TABLE DRESSING GENTS(FD-230/379)

Looking glass complete with frame and back ply, Make- Saint Gobin/ Gold plus

Drawer of 6 mm thick ply wood commercial with front 18mm pre-laminated MDF board and Knob as per existing shape and size

Hat Stand with Mirror (FD-FD-233/361/FD-362)

5mm thick Mirror of size 300mmx440mm of approved brand.

4mm thick commercial plywood for back

Chromium plated MS pegs with screw as approved by Engineer-in-charge

SOFA SET (FD-281/373)

Foam cushion for sofa set size 525x525x100mm, 40 density, Make-Sleepwell duly covered with best quality tapestry cloth as approved by Engineer-in-Charge complete all as directed and specified Note:- Rate of tapestry cloth shall not be less than Rs 250/- per RM

TABLE BED SIDE(MAP) (FD/E-6/MAP/15 (R))

Back ply of 6mm thick commercial plywood of existing shape & size

Drawers made out of 18 mm thick prelaminated particle board with edging

Chromium plated Handle 100mm long

Telescopic channel

TABLE DRESSING LADIES INCL STOOL(MAP) (FD/MAP-II/07)

5mm thick Mirror of size 365mmx1220mm , Make- Saint Gobin/ Gold plus with Back ply of 6mm thick commercial plywood and wooden frame of existing shape & size

Sliding glass shutter of 3mm thick as per existing.

Drawer of 6 mm thick ply wood commercial with 18mm pre-laminated MDF board as per existing shape and size with telescopic channel

Foam cushion 75mm, 40 density covered with fabric on seat to be fixed on 6mm thick ply on stool as per existing shape and size

Wheel at the bottom of stool as per existing shape and size

Bin Linen Multipurpose (Drg No FD/E6/MAP/09)

(A) Right side shutter made out of 18mm thick prelaminated MDF Board colour matched with existing parts with beading as per drawing.

(B) Front shutter made out of 18mm thick prelaminated MDF Board colour matched with existing parts with beading as per drawing.

(C) Drawer made out of 18mm thick prelaminated MDF Board colour matched with existing parts as per drawing.

(D) Top made out of 18mm thick prelaminated MDF Board colour matched with existing parts as per drawing.

(E) Magnetic catcher

(F) Chromium plated MS handle

RE-CANNING OF CHAIRS : Re-canning of wooden chairs, dressing stool, Bin solied linen as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane. Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge.

Polishing of Wooden Furniture Items : All wooden surfaces of the following wooden furniture items wheather exposed to view or not when placed in position shall be polished with high gloss french polish to be finished as directed by Engineer-in-Charge duly preparation of surface with emery paper and applying putty as and where required.

Bed Plywood top - FD 246

Chair Dining FD-228/270/279

Chair Writing FD/261/280

Chair dining officer's FD/E6/MAP/10 (R)

Chair Easy FD-229

Teapoy (FD-278/382)

Peg Table (FD-236/277/384)

Table Writing (FD-275)

Table 900x600mm with drawer and without drawer

Table Dining 6 presons (FD-239/273)

Table Dining 8 presons (FD-239/273)

Side Board (FD-241/371)

Table Centre FD-274/375)

Table 900 x 900mm FD-291

Hat Stand with Mirror (FD-FD-233/361/FD-362)

Sofa Set 4 Seater (FD-281/373)

Sofa Set 5 Seater (FD-281/373/FD/MAP-II/02)

Sofa Set Single Seater (FD-281/373)

Sofa Set 2 Seater (FD-281/373)

Sofa Set 3 Seater (FD-281/373)

Table Office Clerk

Table Office Officers

Table 2'x2'

Taking down worned out/unsv components of the following Steel furniture items, S&F new component as per shape and size specified on respective drawings and as directed by Engineer-in-charge

ALMIRAH LARGE STEEL WITH SHELVES (FD-351/1031) /Almirah Small/Medium steel (FD-350 /1032/243)/Locker Bedside Steel ( FD-257/1029) :-

Shutter (Single Leaf) for Almirah Large Steel made of 1.6 mm thick MS sheet and shall be applied a coat of red oxide primer on both side after preparation surfaces

All as per Item 24.02 here-in-before but for Almirah Small/medium steel

All as per Item 24.02 here-in-before but for Locker Bedside Steel

Shelves for Almirah Large Steel made of 1.25 mm thick MS sheet and shall be applied a coat of red oxide primer on both side after preparation surfaces

All as per Item 24.05 here-in-before but for Almirah Small/medium steel

All as per Item 24.05 here-in-before but for Locker Bedside Steel

Six Levers brass lock for Almirah Large Steel/Almirah small/Med Steel Make : Godrej/Harrison/Link/Plaza with duplicate keys

Three way Locking Device for Almirah Large Steel of 10 mm dia MS rod as per trade pattern incl a coat of red oxide primer

All as per Item 24.09 here-in-before but for Almirah Small/medium steel

Chromium plated Steel Handle 125mm for Almirah Large Steel/Almirah small/Med

Chromium plated MS Key plate fixed with screw and nuts for Almirah Large Steel/Almirah small/Med

Chromium plated 125mm Steel Handle 'D' type for Locker Bedside steel

Leg for Almirah Large Steel/Almirah small/Med Steel made of 1.6 mm thick MS sheet with Gas welding incl a coat of red oxide primer

All as per Item 24.14 here-in-before but 1.0 mm thick MS sheet for Locker Bedside Steel

75mm Chromium plated haps & stapple fixed with rivets of locker steel

Hanging Rod for Locker bed side steeel of 1.6mm thick chromium plated MS Rod

CHAIR CB STEEL WITH ARMS/WITHOUT ARMS ( FD-75(M) )

Seat frame of Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish incl weaving with 2 mm wide half round plastic cane with Godrej pattern & border with 3 mm wide plastic cane superior quality as shown in drawing

All as per item No 25.01 here-in-before but back frame

All as per item No 25.01 here-in-before but Seat frame for Chair CB Steel without Arms

All as per item No 25.03 here-in-before but back frame

Arms rest for Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish

PVC cap at top of the frame of the chair (02 Nos to each chair)

PVC Shoe at bottom of the frame of the Chairs (04 Nos to each chair)

TABLE OFFICE CLERK/Typist STEEL (FD-84(M)/1004/FD-1006)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Drawer made of 22 gauge MS sheet with a coat of red oxide primer

Six levers Lock of Godrej/Harrison with duplicate keys.

Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece not less than 250mm duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface. Upto 300mm long and piece will be counted as one.

PVC Shoe at bottom of the leg of the Table

TABLE OFFICE OFFICER STEEL (FD-84(M)/1003)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Drawer made of 22 gauge MS sheet with a coat of red oxide primer

Six levers Lock of Godrej/Harrison with duplicate keys.

PVC Shoe at bottom of the leg of the Table

TABLE 3' x 2' STEEL WITH DRAWER ( FD-283/1008)/Table for Hav & OR Steel (FD-223/1007)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece not less than 250mm duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface. Upto 300mm long and piece will be counted as one.

Drawer made of 22 gauge MS sheet with a coat of red oxide primer

PVC Shoe at bottom of the leg of the Table

Teapoy Verandah

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

TABLE 3' x 3' STEEL (FD-291/1009)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved by Engineer-in-charge. Sides of the MDF board shall be fixed with PVC edge band tape duly matched the colour with the board all as directed.

Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece not less than 250mm duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface. Upto 300mm long and piece will be counted as one.

PVC Shoe at bottom of the leg of the Table

Charpoy GI Pipe with Plytop: (FD-220)

3 way Galvanized Iron Elbow 32 mm dia. Note weight of each elbow shall not be less than 450 grams

Galvanized iron check nut 32 mm dia. Note :- weight of each check nut shall not be less than 125 grams

Long rail of 32 mm dia galvanized iron pipe medium grade incl threading at both ends as directed

Short rail converted out of retrieved Long rail, Item No 29.03 above incl cutting, threading as required and directed

Leg converted out of retrieved Short rail, Item No 29.04 above incl cutting, threading as required and and directed

Provn of Two Nos MS cleat as shown on drg to hold the MNF set and one MS plate at the bottom to each Leg converted out of retrieved Short rail

12mm thick ply wood top BWR Grade ISI Marked of size 1950mm x 900mm (Single piece).

FOAM WITH BACK (FD-78(M)

Wooden plank for seat of size 1800mm x 255mm x 25mm made out of 1st class hard wood (teak wood) including applying two coats of french polish complete and fixed to steel /iron frame with suitable GI nuts complete all as specified and directed by Engr -in charge.

Wooden plank for back rest of size 1800mm x 150mm x 19mm made out of 1st class hard wood (teak wood) including applying two coats of french polish complete and fixed to steel /iron frame with suitable GI nuts complete all as specified and directed by Engr -in charge.

Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface. Upto 300mm long piece will be counted as one.

FOAM WITH OUT BACK (FD-77(M)

Wooden plank of size 1525mm x 255mm x 25mm made out of 1st class hard wood (teak wood) including applying two coats of french polish complete and fixed to steel /iron frame with suitable GI nuts (09 Nos) complete all as specified and directed by Engr -in charge.

Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface. Upto 300mm long piece will be counted as one.

Chair Computer (TP)

Replacement of complete seat & back with new moulded foam cushioned 40mm density as shape and size covered with synthetic leatherate as approved and as directed by Engineer-in-charge

Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Pedestal assembly complete

Twin wheel coasters press fitted at the bottom of leg.

Hydraulic system

CHAIR WRITING MAP (FD/E6/MAP/12)

Replacement of exising tapestry of seat frame with new tapestry of seat frame approved by Engr-in-charge with PVC liping all round complete all as specified and directed by Engr -in charge Note- Cost of tapestry not less than Rs 200/-

All as per item No 32.01 above but for back frame

Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Replacement of complete seat and back with new moulded foam cushioned 40mm density as shape and size, covered with tapestry cloth not less than 200/- per RM as approved along with PVC liping all round, complete all as specified

CHAIR SCHOOL WITH HAND BOARD (FD/E6/MAP/05)

Hand board of 18 mm pre-laminated MDF board exterior grade with 2mm PVC edging & screwed at right hand side of chair arm fixed to frame as shown on drawing.

Seat & back in one piece made of PVC and fixed with frame

PVC shoe at bottom of the leg

BED HARD STEEL( FD/E6/MAP/08(R))

12mm thick ply wood top of size 1950mm x 900mm (Single piece) BWR Grade ISI Mark with MS screws, complete all as specified

18mm thick prelaminated particle board at head side of the bed as specified

18mm thick prelaminated particle board at foot side of the bed as specified

PVC shoes at the bottom of leg.

CHAIR COMPUTER (FD/E6/MAP/01)

Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size and fixed over 12mm thick hot pressed plywood, covered with tapestry as approved along with PVC liping all round, complete all as specified

All as per item No 35.01 here-in-before but for back frame

Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Pedestal assembly complete

Twin wheel coasters press fitted at the bottom of leg.

TABLE COMPUTER (FD/E6/MAP/03)

Top of 18mm thick pre-laminated MDF board incl PVC lipping all around the top

Drawer of 18 mm thick pre-laminated MDF board fixed with telescopic channel

Shelf for keyboard of 18 mm thick pre-laminated MDF board fixed with telescopic channel .

PVC shoes at the bottom of leg.

TABLE COMPUTER (TP)

Top of 18mm thick pre-laminated MDF board incl PVC lipping all around the top

Drawer of 18 mm thick pre-laminated MDF board fixed with telescopic channel

PVC shoes at the bottom of leg.

RACK SHOE STEEL (FD/E6/MAP/02®)

MS Pipe of 25mm dia for leg frame by welding

MS Jali as shown on drawing

Chair Revolving Steel (TP)

Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size and fixed over 12mm thick hot pressed plywood, covered with synthetic leatherate as approved and as directed by Engineer-in-charge

All as per item No 39.01 here-in-before but for back frame

Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Pedestal assembly complete

Twin wheel coasters press fitted at the bottom of leg.

Hydraulic system

Chair Verandah (FD-256, 259, 359)

Taking out old U/S cane/newar and rubber shoes from chair verandah, removing of foreign materials from the iron frame by rubbing with sand paper, painting two coats with white synthetic enamel paint and recanning seat and back with 4 mm wide half round white plastic cane of superior quality as directed by Engineer-in-Charge

PVC/Rubber shoes as per sample approved

Painting of the following furniture items with two coat of synthetic enamel paint (colour as approved and directed by Engineer-in-Charge) after preparation of surfaces :-

Almirah Steel Large with Shelves, FD-351/1031

Almirah Small/medium steel (FD-350 /1032/243)

Locker Bedside Steel ( FD-257/1029)

Table Dining OR (FD-165(M)

CHAIR CB STEEL WITH ARMS/WiTHOUT ARMS ( FD-75(M) )

TABLE OFFICE CLERK STEEL (FD-84(M)/1004)

Table for Hav & OR Steel (FD-223/1007)

Table (900x600x760)mm steel with drawer (FD-283/1008

Table 3'x3' steel (FD-291/1009)

Table officer officer steel

Book Shelf open steel small (FD-69(M)

Rack side steel with tray, FD-97/1023

Chair writing MAP(FD/E6/MAP/12

Chair School with hard board FD/E6/MAP/05

Bed Hard FD/E6/MAP/08®

Rack Shoe steel FD/E6/MAP/02®

Teapoy Verandah

Form wihout back steel(FD-77/1027)

TABLE DINING OR's ( FD-165(M) )

Cutting down wornout portion of MS Tube of the steel frame and replace with 25mm dia 1.6mm wall thickness MS tube in one piece not less than 250mm duly welding to bring into original size as per drawing, applying of red oxide primer after preparation of surface. Upto 300mm long and piece will be counted as one.

Top of 18/19 mm thick block board of size 1900 mm x 685 mm covered with aluminium sheet 22 guage on top complete all as specified , as directed and shown on drawing.

Rubber shoe to legs

BENCH WORKSHOP STEEL( FD-1024))

40mm thick top made out of 2nd class hard wood with three coats of oil paints complete all as specified and directed.

Drawer made of 1 mm thich MS sheet with coat of red oxide primer including preparation of new steel surfaces complete all as specified

Cutting down wornout portion of MS Tube of the steel frame(each upto300mm will be caounted as one) and replace with 32 x 32 mm Sq tube made of 16 gauge PBI sheet fixed by gas welding incl painting with a cot of red oxide primer including preparation of new steel surfaces complete all as specified.

PVC shoes at the bottom of leg.

Double Buck Chapoy GI (FD-263)

12mm thick BWR Ply wood top in one piece fixing with nut and bolts

Welding to frame and preparation to welding surface as required and directed by Engineer-in-Charge

PACHNANDA BUILDERS

shivom builders

M/S SACHKHAND ROAD SERVICE

VEE KAY IND