PROVN OF ONE SHED FOR GUN REPAIR OF AD REGT WKSP AT OAF UNDER GE 970 EWS

Amount

Surface excavation to required camber and gradient not exceeding 30 cms deep and averaging 15cms deep and getting out in any type of soil, complete all as specified.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in any type of soil all as specified & directed by Engineer-in-Charge.

Material and labour for plain cement concrete 1:4:8, nominal mix, type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete, all as specified & directed.

Material and labour for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work, vertical or to batter to give rough finish to flat surfaces complete all as specified and directed.

Material and labour for form work to sides of pillars, coloumns and similar items (square, rectangular or polygonal) including edges rough finished surface of concrete flat complete all as specified and directed.

Material and labour for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for roughly finished flat surfaces of concrete, all as specified.

Material and labour for reinforced cement concrete 1:2:4, nominal mix, type B-1 using 20mm graded crushed stone aggregate as in foundation, footings, plinth beams etc complete all as specified. Note : Reinforcement and form work shall be measured and paid separately.

Material and labour for reinforced cement concrete nominal mix 1:2:4 type B-1 using using 20mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts, all as specified. Note :- Form work and reinforcement if any shall be measured and paid separately.

Material and labour for plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels, roof beam etc complete all as specified & directed by Engineer-in-charge. Reinforcement if any shall be measured and paid separately.

Material & labour for mild steel high yield strength TMT bars 10 mm dia and over cut to length bent to shape required, including cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Material and labour for mild steel TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hoping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

Material and labour for brick work with sub class ‘B’ bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg / Sqcm) old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Material and labour for rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.290.Gde-E-165, steel work duly painted with one shop coat of zinc chromate primer including preparation of surfaces all as specified.

Supply and fixing Plates 5mm thick or over in thickness in available sizes ,plain or chequered, cut or notched (ordinary and counter sunk) with riveted, bolted or welded attachment using Fe 290 (Gde-E-165), complete all as specified and directed.

Supply and fixing mild steel screw bolt (machine made) with hexagonal at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal n.exc 30cm long & diameter of shank 16-20mm, complete all as specified and directed

Material and labour for preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

Supply and fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws etc complete all as specified & directed by Engineer-in-charge.

Supply and fixing pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, hips , valley gutters, drip and straight flashing(length and girth as fixed), fixed with self tapping screws complete all as specified & directed by Engineer-in-charge.

Material and labour for Moorum/Red bajri filling in floors/embankments/pavements, brought from from approved pits and quarries (out of the MoD land / Ghagar river bed) and laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering to required level and gradient complete all as specified and directed.

Material and labour hardcore of broken stone or boulders of gauge n.exc. 63mm, deposited, spread and leveled in layers n.exc. 15cm thick, watered and rammed to a true surface complete all as specified & directed.

Material and labour for 75mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base of path, floor , hardstanding finishing even and rough receive to top layer complete all as specified & directed.

Material and labour for 25mm thick cement concrete type B-0, 1:2:4 (using 12.50mm graded crushed stone aggregate) as in sub base finishing even and fair to receive to top layer complete all as specified & directed.

Material and labour for plain cement concrete 1:3:6, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate as in plinth protection complete all as specified & directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Removal excavated soil to a distance exceeding 250m and upto distance of 500m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-Charge.

Material and labour for 150mm thick Soling (or sub base) with broker boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber complete all as specified & directed by Engineer-in-Charge.

Material and labour for plain cement concrete 1:2:4,nominal mix ,type B-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed.

Material and labour for sand filling under floor or in foundation including watering and consolidation complete all as specified and directed.

Supply and fixing 60mm thick factory made machine coloured pressed precast concrete interlocking paver block, with grey cement and pigment, any shape and size confirming to IS 15658-2006 of, M-35 grade, joints filled with sand complete all as specified and directed.

Material and labour for plain cement concrete 1:2:4 type B-1 using 20mm graded aggregate as in coping or mud stops rounded or chamfered on edges, complete all as specified & directed.

Supply and fixing energy efficient LED flood light luminaire 50 watt capacity comprises a die-cast aluminium housing including connections with 2 run of 2.5 sqm aluminium unsheathed wire multi stranded from LT over head line / juncton box to the connector of fitting including MS clamps for fixing arrangement complete all as specified and directed. Make : BAJAJ cat Part No BARFEG 50W LED or equivalent make specified in Appx 'C'

Supply and fixing street light junction box IP 66 protected, "halogen free and weather proof" suitable for outdoor type (with metric knockout for cable entry ) of size 139x119x70 mm incl necessary suitable fixing clamps made up of GI flat 32x6mm incl GI nut and bolt complete all as specified and directed.

Material and labour for sub main wiring with 2 core PVC insulated aluminium conductor 4 Sq.mm served with an inner sheathing of PVC tape 1100 volts grade heavy duty cable drawn through and including PVC rigid conduit and fixed on wall /pole etc and connected to light fitting complete all as specified and directed.

PVC sheathed heavy duty electric LT cable XLPE/PVC insulated armoured and with aluminium conductor 1100 volt grade 6 sqmm 2 core laid in trenches in floor, in ducts, through pipe or fixed along the pole complete all as specified and directed. Note:- 1. Excavation, earth work, sand cushioning, and brick protection (if any) shall be included in unit rate. 2. Rate of necessary lugs, thimbles and jointing material shall be included in unit rate.

M/s Bashir Enterprises