PLWSS to Proposed HIMUNDA Colony at Rajwari in Tehsil Balh District Mandi HP

Amount

Excavation in foundation and trenches etc. in earth work in all kind of soils such as pick work jumper work,saturated soil including bailing or pumping out water, blasting soft/hard rock, chiseling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, levelling of bed, stacking the excavated soil clear from the edge of excavation and then returning the excavated soil in 15cm. layers when required into plinths,side of foundations etc including consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated soil as directed in all leads/lifts and shoring strutting, timbering and dewatering where ever required as per direction & best satisfaction of the Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 ( 1cement:4 sand: 8 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1:3:6 (1 cement:3 sand: 6 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frames 30x30x5mm so as to give a fair finish including centering ,shuttering, propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for-in-situ reinforced concrete and plaiin concrete work in:-

Column, Pillars, posts and struts Square,rectangular,polygonal in plan complete in all respect.

Beams, cantilivers, girders and lintels sides and soffits of beams, beam haunchings, cantilivers , girders, bressumers and lintels not exceeding 1 metre in depth complete in all respect.

Flat surfaces such as soffits of suspended floors roofs landings and the like floors etc. up to 200 mm in thickness complete in all respect.

Vertical surface such as walls (any thickness) partitions and the like including attached pillasters, butteresses, plinth and string courses and the like complete in all respect.

Providing and laying cement concrete 1:11/2 :3 ( 1cement: 11/2 sand: 3 graded stone aggregate 20 mm nominal size ) and curing complete excluding the cost of form work and reinforcement in:-

Independent piers columns and pillars upto floor two level complete in all respect.

Suspended floors, roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level complete in all respect.

Foundations, footings, bases of columns, etc. for mass concrete complete in all respect.

Walls (any thickness but ot less than 0.1 mtr thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level up to floor two level complete in all respect.

Providing and laying Reinforced cement concrete work 1:2:4 (1cement: 2sand : 4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in Foundation & plinth complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing Mild steel/Tor steel reinforcement for RCC work including bending, binding and placing in position complete up to floor two level in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and Fixing SFRC Man hole cover of 560mm (MC) dia with frame conforming to IS-12592-Part-II 1998 with latest ammendments. The weight of frame and cover should not be less than 100 kg complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Fixing GMS tubes of following dia in walls, floors etc. including tube fittings and making the wall, floors etc. good complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Inlet and outlet Pipe 80mm dia complete in all respect.

Providing and fixing C. I. Ventilating pipe 100mm dia 1 mtr. with C. I. Cowl fixed at top complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing scouring arrangement from storage tank in a length of 5 mtrs consisting of flanged pipe/nipple of 80 mm dia from storage tank jointed with flanged Cast Steel sluice valve of 80 mm dia Class ASA 150 with Flange table-17 of Kirloskar/Leader / Kartar make. 32mm complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Random rubble masonary/Polygonal rubble masonary (coursed or brought to courses with hard stones of approved quality in foundation and plinth i.c retaining walls including levelling up with cement concrete 1:6:12 in cement mortar 1:6 complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Brick work using common burnt clay building bricks in super structure above plinth level upto floor two level 2nd class bricks cement mortar 1:4 (1cement:4sand) complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Half brick masonary in common burnt clay buildings bricks in cement mortar 1:3 (1 cement: 3 sand) 2nd class bricks complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing/Fixing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed of second class Dedar wood and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing 40 * 3 mm iron hold fast 40 cm long including fixing to frame with 10 cm dia bolts, nuts and wooden plugs and embending in c.c. block 30*10*15 cm 1:3:6 ( 1 cement:3 sand: 6 graded stone aggregate 20 mm nominal size complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

15 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:4 (1 cement: 4 sand) complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

20 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:4 (1 cement:4 sand) complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Stone soling under floor upto 0.15 mtr Thickness comlete in all respects as per the entire satisfaction of Engineer- in - Charge.

Providing and laying cement concrete 1:3:6 (1cement:3 sand: 6 graded stone aggregate 20 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and laying industrial floor tiles of size 600x600 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete of reutated make i.e KAJARIA/ Nitco/ Samoni/ JHONSON etc complete in all respects.

Providing and laying antiskid glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete of reutated make i.e KAJARIA/ Nitco/ Samoni/ JHONSON etc complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing 1st quality ceramic glazed digital wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete of reutated make KAJARIA/ Nitco/ Samoni/ JHONSON etc complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (Two coats) and of required shade on undecurated wall surface to give an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete / stone / plastered wall surface to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for melting of surface complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, of second class Deodar wood including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, greese, dirt and other foreign matters, sand papering and knotting. Ready mixed paint brushing wood primer pink complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Painting two coats (excluding priming coat) on new wood and wood based surfaces, with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matters sand papering and stopping with readymade paint other than white complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing anodised aluminium sliding door bolts with bolts and nuts screws etc Size-250x16mm complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing andised aluminium tower bolts (barrel type) with screws etc Size- 250x10mm complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing MS handles with necessary screws etc Size- 125mm complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1cement: 3sand: 6 graded stone aggregate 20mm nominal size) complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing 100 mm size P or S trap for water closet ( squatting pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1 ( 1 cement :1 sand) Vitreous china complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing vitrous china wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings 550mm X 400 mm complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing 25 cm long PVC connection pipe 15 mm dia with brass union of superior quality as approved by Engineer-in-Charge.

Providing and fixing bath room jet in water closet complete in all respect including PVC Connection pipe with brass check nut and all other accessories contingent thereto complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing CP Concealed angle cock ISI marked of reputed make complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing chromium plated bib cock of 15 mm dia of superior quality as approved by Engineer-in -Charge.

Providing and fixing chromium plated brass waste coupling for wash basin or sink 32 mm dia including all accessories of superior quality as approved by Engineer-in-Charge.

Providing and fixing 600mm X 450 mm beveelled edge mirror of superior glass mounted on 6mm thick AC sheet or plywood sheet and fixed to wooden plugs with CP brass screws and washers complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing PVC Pipe 100 mm dia of Phinolex/ Diplast make complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and Fixing GI unions 15 mm dia complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and Fixing GI elbow 15 mm dia complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and Fixing GI Tee 15 mm dia complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and Fixing GI sockets 15 mm dia complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and Fixing to wall, ceilling and floor galvanised mild steel tube (MG) , fitting and clamps including making good the same ic.c. wall, ceiling and flooring 15mm dia complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and Fixing GI nipples 15mm dia (15cm long) complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing CP brass towel rail 600x150 mm complete with CP brass screws and accessories.Shoup Tumbler, Jali etc ISI mark complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and fixing chromium plate bib cock with Long Body i/c all fitting in Wash basin of ISI mark superior quality as approved by the Engineer-in-Charge

P/F chromium plated over head shower with shower arm ISI mark complete in all resepct of superior quality as approved by the Engineer-in-Charge.

Providing and Fixing PVC water storage tank 500 ltrs capacity with fitting complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge. Sintex/ Diplast make

Manufacturing & Suppling of Fencing panels of Size 2.5 mtr x 0.50 mtr devided in Two Panels of 1.00 m X 0.50 m by fixing duly welded, back to back angle at centre of frame, fitted with 25 mm x25mmx3mm wire mesh welded to MS angle frame of 40x40x3mm all around and MS flat cover over mesh of size 25x5mm and Hold fasts etc. complete pannel including all process of cutting, welding painting with red oxide paint complete in all respect with in all leads and lifts as per directions and satisfaction of Engineer- in- Charge

Steel work welded in built up sections, trusses and framed work including cutting,hosting,fixing in position and applying a priming coat of red lead paint in gratting framed guard bars, ladders, railing etc complete in all respect with in all leads and lifts as per directions and satisfaction of Engineer- in- Charge

Electrical Wiring :- Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

Group C.

Wiring for circuit / sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

i) 2 x 1.5 Sq. mm.

ii) 2 x 4.00 Sq. mm.

(a) Supplying and fixing 3 pin 5/6 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

(b) Supplying and fixing 2 way 5/6 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connections etc. as required.

(a) Supplying and fixing 3 pin 15/16 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

(b) Supplying and fixing 15/16 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connections etc. as required.

Supplying and fixing wooden box of following size (nominal) on surface or recess with suitable size of phenolic laminated sheet cover of in front as required.

(a) 229 mm.x 102 mm.x 60 mm. deep

(b) 203 mm.x152 mm.x 60 mm. deep

Supplying and fixing ceiling rose on existing junction box/ wooden block including connections etc. as required.

Supplying and fixing plain pandent with 16/20 mm twin twisted, flexible PVC insulated copper cable and backelite pendant holder including connections, etc. as required.

Supplying and Fixing 5 Amps to 32 Amps rating, 240 Volts, L series miniature circuit breaker of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required Cat - A. (Single Pole)

Supplying and Fixing of following way, single pole and neutral, sheet steel, MCB distribution board, 240 Volts on surface/ recess, complete with tinned copper busbar, netural link, earthbar, dibnbar, detachable gland plates, inter connections, i/c painting, earthing etc. as required busbar 8 way.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (63 amp. CAT - A)

Providing, installing, testing and commissioning of ceiling fan and regulator i/c wiring the down rod of standard length (upto 30 Cm with 1.5 Sqmm PVC insulated copper conductor signle core cable etc. as required.Ceiling fan 1400 mm sweep category A

Providing and fixing ultra slim decorative extruded box fixture with domestic electronic ballast, snap-on installers, suitable for 28 watt FTL (T5), complete with all accessories (including one No. T-5 Tube), connections, testing and commissioning etc. as required.

1 x28 watt-FTL(T5) (Category-A)

Providing and fixing LED Lighting ROADWAY LUMINAIRES Single Piece, Pressure Die-Cast Aluminium Housing, Top Opening Luminaires (IP 65) with all accessories including cost of lamp ISI mark LHETBAU7PN6J020 Havell's make or BajaJ Make BCLST 20 W LED complete with all accessories and ballast i.e. 15/16 amp. switch & socket with board,copper wire 8 SWG (4 mm dia) Bracket and suitable angle clamps for fixing and other fittings etc.complete in all respect in all leads and lifts.

P/F of complete Gaseous Chlorination system for Water Treatment:- Supply installation with testing Vaccume feed wall mounted chlorinator of capacity upto 10 KGS/Hr complete in all respect in all leads and lifts as per the entire satisfacttion of Engineer in Charge.

Chlorine Gas Injector complete in all respect in all leads and lifts as per the entire satisfacttion of Engineer in Charge.

Providing, installation and commissioning single Phase Monoblock Pump 3 HP complete in all respect in all leads and lifts as per the entire satisfacttion of Engineer in Charge.

Providing installation PVC pipe fitting complete in all respect in all leads and lifts as per the entire satisfacttion of Engineer in Charge.

Providing and installation of Chlorine Gas Cylinder 100Kg complete in all respect in all leads and lifts as per the entire satisfacttion of Engineer in Charge.

Providing and supplyiong of safety Kit complete in all respect in all leads and lifts as per the entire satisfacttion of Engineer in Charge.

Rising Main and Pumping Machinery:- Laying, jointing, testing and carriage in trenches to be leveled to grades, IS marked GI Pipe (Heavy) flanged pipes of following diameters conforming to IS 1239-1990 (part-II) (latest with up to date ammendments) having minimum wall thickness as for class of pipe specified below jointed with flanges conforming to tables as specified below of BIS 6392-1971 (latest with up to date ammendments) welded at both ends according to relevant BIS standards and detailed specifications as appended in NIT & provided with nuts & bolts of required sizes, 3mm thick compressed asbestos fibre gasket of synthetic rubber gasket conforming to relevant BIS codes as given in technical specifications including all leads and lifts, flanged short pieces, bends, tees and other specials etc. made from parent tubes including bends & welded with flanges of tables as aplicable for the particular reach & of technical specifications appended in the NIT as per site conditions including flushing cleaning & hydraulic testing as per directions of the Engineer-in-Charge.

Dia of Pipe (MM), Class, IS Specifications, Wall Thickness, F.Table

T/Well No.1 Chhalkhi & T/Well at Dadoh

80mm dia H GI IS :1239 4.80 17

80mm dia H GI IS :1239 4.80 5

1st Stage

100mm dia H GI IS :1239 5.40 28

100mm dia H GI IS :1239 5.40 17

100mm dia H GI IS :1239 5.40 5

Laying, jointing, testing and carriagein trenches to be leveled to grades, IS marked GI pipes (Heavy ) Butt Welding of following diameters conforming to IS 1239-1991(Part II ) (latest with up to date ammendments) , including Butt welding of pipe ends to make water tight joint including carriage of material up to all leads and lifts. This work aslo includes fabrication of short pieces, bends, tees & other specials etc. from parent tubes with butt welding in three layres as applicable for the particular reach & of technical specifications as per site conditions including flushing, cleaning & hydraulic testing complete to the best satisfaction of Engineer in Charge. The laying of pipe shall conform to IS: 5822-1994 and as per CPHEEO manual. The rates also include the carriage of GMS tubes from the JSV divisional store Baggi to the site of work , butt welding of joints , fabrication of short pieces, bends, tees & other specials etc. from parent tubes , flushing, cleaning & hydraulic testing complete to the best satisfaction & direction of Engineer in Charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately).

Dia of Pipe (MM), Class, IS Specifications, Wall Thickness, F.Table

T/Well No.1 Chhalkhi & T/Well at Dadoh

80mm dia H GI IS :1239 4.80

1st Stage

100mm dia H GI IS :1239 5.40

Providing, laying, jointing and testing in trenches ( to be levelled to grades) MSERW API-IS:3183 flanged pipes of following diameter, class & wall thickness and IS specification capable to withstand the required hydraulic test pressure as per IS Code in a random length of 4 mtrs. to 7 mtrs. with bevelled ends and jointed with flange table mentioned below conforming to IS-6392-1971(latest with up to date ammendments). The welding of flanges to be done on both faces in double layer to make the joint leak proof according to relevant BIS standard and specifications. The pipe including nuts and bolts of required size, 3mm thick compressed asbestos fibre jointing gasket/ synthatic rubber jointing gasket should be conforming to relevant BIS code. Laying will include all operations such as cutting, welding, painting and jointing including flushing, cleaning and hydraulic testing of pipe complete in all respect and to the entire satisfaction of the Engineer-in-Charge.

Dia of Pipe (MM), Class, IS Specifications, Wall Thickness, F.Table

100mm dia API-IS:3183 4.00 34

100mm dia API-IS:3183 4.00 28

Providing , laying, Jointing and testing of trenches to be leveled to grades, MSERW/API-IS:3183 pipes with Butt welding of following diameters conforming to IS 3183-2007 ( latest with up to date ammendments ) of steel grade B, jointing the pipes with butt welding at both ends according to relevent BIS standards/ approved specifications including manufacturing reducers/tapers, all short pieces and bends as per site requirement and made from parent tubes (to be measured and paid alongwith pipes). Bends shall be manufactured in such a way that not more than 11 1/4 degree deflection is caused by a single cut and internal dia is not reduced including hydraulic testing to the best satisfaction & direction of Engineer in Charge. The pipes and specials shall have in factory galvanized coating as per IS: 4739 (with latest ammendments). The damaged portion of galvanization due to welding shall be provided with anticorrosive treatment by applying two coats of bituminious paint over priming coat as per AWWA specification C-203-1978. (Earth work to be measured & paid for separately) complete in all respects with in all leads & lifts as per the entire satisfaction & directions of Engineer- in- Charge.

Dia of Pipe (MM), Class, IS Specifications, Wall Thickness, F.Table

100mm dia API-IS:3183 4.00

Submersible Stage T/well No. 1 At Chalkhi:- Supply of Submersible RW Pump Set confirming to ISO 9906 Suitable To Handle turbidity Upto 600 PPM Of KSB/Kirloskar/ Sabar/ Jhonston/ Chromton / Kalma make instead of clear water pump conforming to BIS: 8034 for 100 PPM or latest suitable for lifting water ( Latest with up to date ammedments ) fitted with bronze impeller / suitable alloy. The Pump Should be fitted with free flow impellers of bronze / suitable alloy directly coupled to Squirrell cage electric induction motor of same make as (manufacturer standared) conforming to BIS: 9283/ 1979 ( Latest With Up to date ammendments ) totaly water proof for submersible duty, isolated from the pump by intermidiate casing with double mechenical seal in oil chamber, greased packed lubricating bearing and provided with stainless steel thrust bearing plate to withstand vertical loads with minimum wear and tear. It should also be fitted with a device to take up expention of water with the heating of motor including water level gaurd errection clamps manufracturere cable clips and depth gauge etc. The pump shell be suitable for operation on the data as given below.

A) SITE CONDITIONS:- i) Location of site-About 15 Km. from Ner Chowk ii) Thre altitude of place in which the motor is intended to work in ordinary service if it exceeds 1000mtrs- Altitude of place is 797 m above MSL.iii)Detail of quality of water-Clear cold water. iv) Water free from sand or not-Yes v) Water corrosive or not- No vi) Turbidity- (if any) Clear cold water. B.PUMPS:BIS 1520-1980,READ WITH BIS 9137-1978 BOTH LATEST WITH UPTO DATE AMMENDMENTS. i) Nos of pumps reqd.-2 No. pumps ( one will act as stand by). Pump operating conditions. i) Capacity- 3.38LPS ii) Total head in Mts.- 69.35 Mtrs. iii) (If total head in not known then following details be provided): iv) Static Head- 66.00 Mtrs. v) Minimum depth of water- ………….Mtrs. vi) Variation in water level.- ………….Mtrs. vii) Ground level to max. water level- ………….Mtrs. viii) Ground level to delivery point- ………….Mtrs. ix) Pressure in the suction tank- …………..Kg/cm/2 x) Pressure in the delivery tank- …………..Kg/cm/2 xi) Length of R/main- 390 Mtr. xii) Dia of R/main-80 mm Dia xiii) No. of working hours per day- 8 Hours

Supply , Installation, Testing and Commissioning of Star Delta Starter panel for submersible pump made out of 16 Gauge sheet, powder coated dust and vermin proof, wall/base mounted and front opening door type with copper insulated wiring suitable to operate 2 Nos. pumps (1 working & 1 stand by) each of the rating 7.5 HP through Star Delta Starter mechanism. Starter should be capable enough to handle the following faults like short circuit, over current, under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicators Of reputated make i.e JSV Approved etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Star, Delta and Mains Power Contactors of required ratings as per type-2 co-ordination for 7.5 HP starter complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Voltage Protection device to protect panel from over voltage and under voltage complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc with RS 485 communication Make JSV Approved/MAS/Elle etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Main incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Individual Starter incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

LED On / Off & Trip indicator and push buttons, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Bus Bar, i.e.Bolt, insulator, etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Surge supressor device with Isolating MCCB to eliminate the power surges due to lightening and system surges complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Control Transformer to provide a stable control volatge to safegaurd the control circuit of all the components from the voltage surges and spikes complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Independent Control Panel with Switch Fuse Unit and Fuses of Suitable Amperage to eliminate the KItKat fuses of HPSEB Of reputated make i.e Aarmation/Siemens/Schnieder/L&T etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel sluice valve, ASA-150 of Leader/BHEL/ Kirlosker/Kilburn /GLEd/Fourses make and one step higher then delivery line of pump and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel reflux valves class, ASA-150 of Leader/BHEL/ Kirlosker/Kartar/Kilburn /GLEd/Fourses make for rising main and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing 100mm dia circular dial analog pressure gauge of suitable range of Fiebig /Bourden/ PREGA/precision make complete with all accessories such as stop cock, copper tubing etc.as per IS: 3624-1987 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing disCharge meter of standard make to be fixed on the rising main in pump house as per the directions of the Engineer in Charge as per Is:2373:1981 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Installation of all the items apparing as per the schematic drawing complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing and laying copper PVC insulated armoured power cable (One cable carrying all the three phases) of suitable size and capacity to motors and all other electircal equipments as per IS:1554(P-I) 1988 or latest ith upto date ammendments of siemens/GLOSTER /IEC/ICC/EICO/NATIONAL/GRANDLAY make including all other accessories such as thinbles, flexible pipes,solders,nuts and bolts cable glands etc. laid in pipes or trenches under floor complete in all respect as per the entire satisfaction of Engineer-in- Charge.

(a) Motor side (From switch to starter and starter to motor) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

(b) Supply side (From Meter of HPSEB to bus bar and switch) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing and fixing double loop earthing with GI plate 600mmx600x3mm thick electrode complete with material such thimbles nuts and charcoal and common salt, 25mmx5mm copper strips as per IS:3043:1987 with upto date ammendments for motors and other electrical equipments and digging of pits etc. complete in all respect.

Low Cost Automation:- PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel Make JSV Approved complete in all respect.

Electronic relay card 8 channel complete in all respect.

SMPS 4.5 Amps to energise PLC system complete in all respect.

HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps Make: JSV Approved complete in all respect.

Control MCB for Automation System complete in all respect.

Level Sensor to indicate the water level of tank remotely complete in all respect.

Shielded Data Cable for Communication of Level Sensor with PLC complete in all respect.

Submersible Stage T/well No. 1 At Dadoh:- Supply of Submersible RW Pump Set confirming to ISO 9906 Suitable To Handle turbidity Upto 600 PPM Of KSB/Kirloskar/ Sabar/ Jhonston/ Chromton / Kalma make instead of clear water pump conforming to BIS: 8034 for 100 PPM or latest suitable for lifting water ( Latest with up to date ammedments ) fitted with bronze impeller / suitable alloy. The Pump Should be fitted with free flow impellers of bronze / suitable alloy directly coupled to Squirrell cage electric induction motor of same make as (manufacturer standared ) conforming to BIS: 9283/ 1979 ( Latest With Up to date ammendments ) totaly water proof for submersible duty, isolated from the pump by intermidiate casing with double mechenical seal in oil chamber, greased packed lubricating bearing and provided with stainless steel thrust bearing plate to withstand vertical loads with minimum wear and tear. It should also be fitted with a device to take up expention of water with the heating of motor including water level gaurd errection clamps manufracturere cable clips and depth gauge etc. The pump shell be suitable for operation on the data as given below.

A) SITE CONDITIONS:- i) Location of site-About 15 Km. from Ner Chowk ii) Thre altitude of place in which the motor is intended to work in ordinary service if it exceeds 1000mtrs- Altitude of place is 795 m above MSL.iii)Detail of quality of water-Clear cold water. iv) Water free from sand or not-Yes v) Water corrosive or not- No vi) Turbidity- (if any) Clear cold water. B.PUMPS:BIS 1520-1980,READ WITH BIS 9137-1978 BOTH LATEST WITH UPTO DATE AMMENDMENTS. i) Nos of pumps reqd.-2 No. pumps ( one will act as stand by). Pump operating conditions. i) Capacity- 3.72LPS ii) Total head in Mts.- 65.75 Mtrs. iii) (If total head in not known then following details be provided): iv) Static Head- 66.00 Mtrs. v) Minimum depth of water- ………….Mtrs. vi) Variation in water level.- ………….Mtrs. vii) Ground level to max. water level- ………….Mtrs. viii) Ground level to delivery point- ………….Mtrs. ix) Pressure in the suction tank- …………..Kg/cm/2 x) Pressure in the delivery tank- …………..Kg/cm/2 xi) Length of R/main- 90 Mtr. xii) Dia of R/main-80 mm Dia xiii) No. of working hours per day- 8 Hours

Supply , Installation, Testing and Commissioning of Star Delta Starter panel for submersible pump made out of 16 Gauge sheet, powder coated dust and vermin proof, wall/base mounted and front opening door type with copper insulated wiring suitable to operate 2 Nos. pumps (1 working & 1 stand by) each of the rating 7.5 HP through Star Delta Starter mechanism. Starter should be capable enough to handle the following faults like short circuit, over current, under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicators Of reputated make i.e JSV Approved Etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Star, Delta and Mains Power Contactors of required ratings as per type-2 co-ordination for 7.5 HP starter complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Voltage Protection device to protect panel from over voltage and under voltage complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc with RS 485 communication Make JSV Approved/MAS/Elle etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Main incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Individual Starter incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

LED On / Off & Trip indicator and push buttons, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Bus Bar, i.e.Bolt, insulator, etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Surge supressor device with Isolating MCCB to eliminate the power surges due to lightening and system surges complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Control Transformer to provide a stable control volatge to safegaurd the control circuit of all the components from the voltage surges and spikes complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Independent Control Panel with Switch Fuse Unit and Fuses of Suitable Amperage to eliminate the KItKat fuses of HPSEB Of reputated make i.e Aarmation/Siemens/Schnieder/L&T etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel sluice valve, ASA-150 of Leader/ BHEL/ Kirlosker/ Kilburn/ GLEd/ Fourses make and one step higher then delivery line of pump and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel reflux valves class, ASA-150 of Leader/ BHEL/ Kirlosker/ Kartar/ Kilburn/ GLEd/ Fourses make for rising main and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing 100mm dia circular dial analog pressure gauge of suitable range of Fiebig /Bourden/ PREGA/precision make complete with all accessories such as stop cock, copper tubing etc.as per IS: 3624-1987 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing disCharge meter of standard make to be fixed on the rising main in pump house as per the directions of the Engineer in Charge as per Is:2373:1981 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Installation of all the items apparing as per the schematic drawing complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing and laying copper PVC insulated armoured power cable (One cable carrying all the three phases) of suitable size and capacity to motors and all other electircal equipments as per IS:1554(P-I) 1988 or latest ith upto date ammendments of siemens/GLOSTER /IEC/ICC/EICO/NATIONAL/GRANDLAY make including all other accessories such as thinbles, flexible pipes,solders,nuts and bolts cable glands etc. laid in pipes or trenches under floor complete in all respect as per the entire satisfaction of Engineer-in- Charge.

(a) Motor side (From switch to starter and starter to motor) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

(b) Supply side (From Meter of HPSEB to bus bar and switch) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing and fixing double loop earthing with GI plate 600mmx600x3mm thick electrode complete with material such thimbles nuts and charcoal and common salt, 25mmx5mm copper strips as per IS:3043:1987 with upto date ammendments for motors and other electrical equipments and digging of pits etc. complete in all respect.

Low Cost Automation:- PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel Make JSV Approved complete in all respect.

Electronic relay card 8 channel complete in all respect.

SMPS 4.5 Amps to energise PLC system complete in all respect.

HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps Make:JSV Approved complete in all respect.

Control MCB for Automation System complete in all respect.

Level Sensor to indicate the water level of tank remotely complete in all respect.

Shielded Data Cable for Communication of Level Sensor with PLC complete in all respect.

Centrifugal Stage for HIMUDA :- Supply of horizontal spindle Horizontal Radial split casing /and suction (back pull out arrangement ) Single / Double /Multistage Centrifugal Pump or combination of pumps in series / Parallel of KSB / Mathur & Platt / Jyoti / Kirloskar / BE / Maxflow / Beaconweir Sabar make Confirming to BIS: 5659-1970 ( pumps latest with upto date ammendments ) read with BIS:9137-1978 ( Latest Addition Suitable for lifting water of under mention characterstics with Bronze / Suitable Alloy, primming funnels, casing ring & Shaft Motors of Bronze, Shaft of steel grade ASA-410 with cast Iron Casing coupled directly through a flexible coupling on a common MS/ Cast Steel Plate ( Base Plate From The principle manufracturer of pumping set) to coupling of electic induction motor / motor of standered make such as kirloskar/ NGEF /Cromton/ Siemen / jyoti / Bhel / GEC / ABB and suitable for operation on 415 (+- 10% ) volts 50 cycle per second three phase AC electric supply confirming to BIS 325-1978 read as BIS 900-1972 & IS 12615-211 with IE-2 specification 2900 RPM ( Latest With upto date ammendments ) it should include the cost of bearing, Nuts and bolts , painting Etc and shell be Suitable For Operation on the data given as below t of steel with cast iron casing of suitable capacity coupled directly through a flexible coupling on a common base plate to kirloskar/NGEF/ Crompton/Siemen/Jyoti/ABB/Marathan Squirrel cage screen protected drip proof induction electric motor suitable for operation on the data given below. 2 x 75 = 150 ( One Act as a Stand By ) Detail Of automation with allied accessories attached in detail of measurement.

A) SITE CONDITIONS:- i) Location of site-About 15 Km. from Ner Chowk ii) Thre altitude of place in which the motor is intended to work in ordinary service if it exceeds 1000mtrs- Altitude of place is 795 m above MSL.iii)Detail of quality of water-Clear cold water. iv) Water free from sand or not-Yes v) Water corrosive or not- No vi) Turbidity- (if any) Clear cold water. B.PUMPS:BIS 1520-1980,READ WITH BIS 9137-1978 BOTH LATEST WITH UPTO DATE AMMENDMENTS. i) Nos of pumps reqd.-2 No. pumps ( one will act as stand by). Pump operating conditions. i) Capacity- 6.77 LPS ii) Total head in Mts.- 441.60 Mtrs. iii) (If total head in not known then following details be provided): iv) Static Head- 369 Mtrs. v) Minimum depth of water- ………….Mtrs. vi) Variation in water level.- ………….Mtrs. vii) Ground level to max. water level- ………….Mtrs. viii) Ground level to delivery point- ………….Mtrs. ix) Pressure in the suction tank- …………..Kg/cm/2 x) Pressure in the delivery tank- …………..Kg/cm/2 xi) Length of R/main- 4500 Mtr. xii) Dia of R/main-100 mm Dia xiii) No. of working hours per day- 8 Hours

Supply , Installation, Testing and Commissioning of Energy Saving Variable Frequency Starter Panel for centrifugal pump made out of 16 Gauge sheet, powder coated dust and vermin proof, wall/base mounted and front opening door type with copper insulated wiring suitable to operate 2 Nos. pumps (1 working & 1 stand by) each of the rating 75 HP . Starter should be capable enough to handle the following faults like short circuit, over current, under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicators, Power Quality Monitoring & Controlling Relay at the Incomer Feeder, Should be fitted with Surge Suppressor Device suiatble to protect against class-1 & 2 surges. of reputated make i.e JSV Approved complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Energy Saving Variable Frequency Starter of 75 HP Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to monitor & control the frequecy of pumps through out the operation and to maintain the power factor of the system within acceptable limits. It should be able to withstand ambient temperature upto 50 Degrees celcius without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make: JSV Approved complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc. with RS 485 communication Make:- L&T/Conserve/Schnieder/JSV Approved complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Main incomer MCCB of suitable capacity of L&T / Schnieder/ABB/Siemens make on the coming feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) complete in all respects as per the entire satisfaction of Engineer-in- Charge.

LED Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments complete in all respects as per the entire satisfaction of Engineer-in- Charge.

LED On / Off & Trip indicator and push buttons, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Bus Bar, i.e.Bolt, insulator, etc. complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Input Choke of required HP for Energy saving variable frequency Starter which should be installed at the input of Energy saving variable frequency starter, so that there should be proper protection in case of any voltage surge and distortions complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Control Transformer Make: JSV Approved/MAS/Elle complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Power and Control Wiring and Busbar complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Installation, Commissioning and Software Development complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Surge supressor device with Isolating MCCB to eliminate the power surges due to lightening and system surges complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Power quality monitoring & controlling relay with Control Contactor to safeguard the Electronic & Electric elements complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Independent Control Panel with Switch Fuse Unit and Fuses of Suitable Amperage to eliminate the KItKat fuses of HPSEB Make: Aarmation/Siemens/Schnieder/L&T/JSV Approved complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged CI Sluice valve PN-1 of Leader/BHEL/ Kirlosker / GLED/Kilburn /Fourses /Kartar make and equal to dia of suction pipe and capable of withstanding the normal seat pressure as per IS:780:1984 with up to date ammendments) complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel sluice valve, ASA-300 of Leader/KSB/ Kirlosker/ make and one step higher then delivery line of pump and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel reflux valves class, ASA-300 of Leader/BHEL/ Kirlosker/Kartar/Kilburn /GLEd/Fourses make for rising main and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel reflux valves class, ASA-300 of Leader/BHEL/ Kirlosker/Kartar/Kilburn /GLEd/Fourses make for rising main and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Providing 100mm dia circular dial analog pressure gauge of suitable range of Fiebig /Bourden/ PREGA/precision make complete with all accessories such as stop cock, copper tubing etc.as per IS: 3624-1987 with upto date ammendments complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Providing disCharge meter of standard make to be fixed on the rising main in pump house as per the directions of the Engineer in Charge as per Is:2373:1981 with upto date ammendments complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Installation of all the items apparing as per the schematic drawing complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Providing and afixing double flanged MS/GI pipin g work (lay out to be approved by the Engineer in Charge) for suction and delivery pipe suitable to pumps (S) offered and commaon header as per the rising main respectevely complete with all specials such as bends, tees, reducers, increasers with companinon flanges matching with the relevent specifications of the accessories including rubber/asbestos gasket of minnimum 3mm thickness as per IS 2712:1979 and required no. of nuts and bolts as per IS 1354-1983. The pipe fittings and joints shall be as per relevant IS codes and to with stand 1.5 times total head stipulated. The size of the various components to be as under.

Suction pipe : one dia higher than the suction of pump offered and suitable to keep the velocity of flow from one to 1.5 mtr per sec. In the suction pipe.

Delivery pipe : one dia higher than the delivery of pump offered and suitable to keep the velocity of flow from 1.5 to 2 mtr per sec. In the delivery pipe.

Common Header : one dia higher than the delivery of pump will extend upto 5mtrs from the outer wll of the pump house to the direction to be jointed.

Providing and laying copper PVC insulated armoured power cable (One cable carrying all the three phases) of suitable size and capacity to motors and all other electircal equipments as per IS:1554(P-I) 1988 or latest ith upto date ammendments of siemens/GLOSTER / IEC / ICC/ EICO/ NATIONAL/ GRANDLAY make including all other accessories such as thinbles, flexible pipes,solders,nuts and bolts cable glands etc. laid in pipes or trenches under floor complete in all respects as per the entire satisfaction of Engineer-in- Charge.

(a) Motor side (From switch to starter and starter to motor) complete in all respects as per the entire satisfaction of Engineer-in- Charge.

(b) Supply side (From Meter of HPSEB to bus bar and switch) complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Providing and fixing double loop earthing with GI plate 600mmx600x3mm thick electrode complete with material such thimbles nuts and charcoal and common salt, 25mmx5mm copper strips as per IS:3043:1987 with upto date ammendments for motors and other electrical equipments and digging of pits etc. complete in all respect.

Automation System for Unmanned Operations with SCADA features, PLC, HMI and Level Sensor:- PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel Make JSV Approved complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Electronic relay card 8 channel complete in all respects as per the entire satisfaction of Engineer-in- Charge.

SMPS 4.5 Amps to energise PLC system complete in all respects as per the entire satisfaction of Engineer-in- Charge.

HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps Make:JSV Approved complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Control MCB for Automation System complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Level Sensor to indicate the water level of tank remotely complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Shielded Data Cable for Communication of Level Sensor with PLC complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Supply of Mobile App (Android/IOS) with User ID and Password to monitor and control the pumping operation from Mobile for 3 users. Make: JSV Approved complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Cloud GateWay for Data Clouding to Server complete in all respects as per the entire satisfaction of Engineer-in- Charge.

SCADA software to be installed in Laptop/PC to remotely monitor and control the operation of pumps and also to analysis the pump start and stop history logging, fault status, fault history, Power Quality Parameters like PF, Current, Voltage, KWH, THD etc Make JSV Approved complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Cloud Space for data storage at cloud/server complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Supply and Installation of Electromagnetic Flow Meter of required rating to analyse the disCharge/Total quantum of water supplied complete in all respects as per satisfactionof engineer inCharge Approved Makes: Leader/Kirloskar/KSB complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Installation, Commissioning and Software Development complete in all respects as per the entire satisfaction of Engineer-in- Charge.

Operation and Maintenance of complete scheme:- 2 years for trail +Three years with automation complete job in all respects as per the entire satisfaction of Engineer-in- Charge.

Anurag Deep

KUSHAL SINGH RAGHAV