REPAIR MAINT OF PUMP MOTOR DG SETS AND ALLIED WORK UNDER AGE EM AT GE FAIZABAD

Amount

S & F MCCB 4 pole 100 Amp, 415 volt, 25 KA of make: L&T or equivalent in C&S, Scheinider,siemens in existing panel including taking out of old one , complete all as sepcified.

S & F On load Changeover 4 pole 100 Amp, 415 volt, open execution type of make: L&T or equivalent in C&S, Scheinider,siemens in existing panel including taking out of old one , complete all as sepcified.

S & F digital type Voltmeter with LED display suitable for 3 phase of make: L&T or equivalent in C&S, Scheinider,siemens in existing panel including taking out of old one , complete all as sepcified.

M & L for 3 pole power contactor 220/440 volts with 50 Amp AC3 duty rating any type including auxillary switch of make: L&T or equivalent in Schneider/ Siemens in existing panel including taking out of old one , complete all as sepcified.

M & L for electronic timer for automatic star delta starter 415 volt 50 Hz 3 - 30 sec of make: L&T, in existing panel including taking out of old one , complete all as sepcified.

S & F digital type Ammeter with LED display suitable for 3 phase make: L&T or equivalent in existing panel including taking out of old one , complete all as sepcified.

S & F tape wound ring type Current Transformer suitable for Bar primary of rating 100/5 Amp, burden 5 VA of make: Kappa/ Matrix or equivalent in existing panel including taking out of old one , complete all as sepcified.

S & F Single phase Preventer Relay with adjustable time delay 30 sec to 5 min suitable for 415 volt AC, any type of make: L&T or equivalent including internal wiring from switchgear to relay in existing panel , complete all as sepcified.

S & F overload Relay any type suitable for 5 Amp to 30 Amp 415 volt AC of make: L&T or equivalent including internal wiring from switchgear to relay in existing panel , complete all as sepcified.

S & F Three phase submersible pump controller with single phase preventer of rating 3 phase,415V,50 HZ, 40 HP ,Type MU-G40 FASD, of make L&T, Sceinider or equivalent including taking out of old one , complete all as sepcified.

M&L for fixing of DOL starter three phases 415 Volt for 7.5 HP electric motor including all fixing materials , complete all as sepcified.

M&L for fixing of DOL starter three phases 415 Volt for 10 HP electric motor including all fixing materials , complete all as sepcified.

M&L for fixing of DOL starter three phases 415 Volt for 20 HP electric motor including all fixing materials , complete all as sepcified.

Supply & Fixing of Flat three core submersible cable PVC insulated and sheathed multistranded copper conductor of cross sectional area 16 sqmm , complete all as sepcified of make: Havells , Kalinga ,Polycab or equivalent .

Supply & fixing LED street light fitting 120W Rectangular LED Flood Light with innovative thermal management and available in multiple optics and equipped with IP66 protection with required connection wire multistand 2.5 Sqmm twin core sheathed weather proof up to ACSR conductor/ Ceiling rose , complete all as sepcified.. Make:- Cromption cat pat No:- LFLN-100-CDL/60 or Equvalent of Bajaj/Philips

S&F FR PVC Insulated Single core unsheathed Industrial Flexible cable of size 16 sqmm conforming to IS 694:2010 with bright annealed copper conductor in existing panel including taking out of old one , complete all as sepcified. Make : Polycab or equivalent as approved by GE .

Disconnecting electrically incomming and outgoing LT UG cable of LT panel of any size and replace burn/unsv suitable size of aluminium bus bar, Welding work for hinches and doors, fixing the locking arrangement including scraping outdoor/indoor side of LT Panel and one coat of redoxide, two coat of synthetic enamelled seimens gray spray of outdoor/Indoor side and reconnecting LT UG cable with fixing aluminium lugs by using crimping tool, nut, bolt washer etc and all necesary work required for smooth functioning of LT panel , complete all as sepcified.

Supply only bleaching powder in 25 Kg bag (ISI marked) grade II , complete all as sepcified.(Make: Punjab Alkalies/Modi Alkalies/Sriram as approved).

Supply only sodium hypochloride liquid (chlorine content 10%) duly packed in sealed drum of make: M/s Declibac/ M/s Rayalshima Enterprise/ Birla Chemicals or equivalent as approved by GE, complete all as sepcified.

Collection of water samples of bore wells located in deferent pockets of cantonment area in decontaminated sterilised bottles and testing of water samples for following essential parameters for drinking water as per IS:10500- 2012 from Govt Lab or NABL accredited laboratory: - (i) Colour (ii) odour (iii) taste (iv) pH value, (v) Turbidity (vi) TDS (vii) Total arsenic (viii) Silica (ix) Fluoride (x) Iron (xi) Magnesium (xii) Sulphate (xiii) Total Hardness (xiv) Total alkalinity (xv) Calcium (xvi) Conductivity (xvii) Chloride (xviii) Total Coliform and (xix) E Coli, complete all as sepcified.

M&L for Rolled mild steel in Joist ,channel,angle, or tee sections, fixed independently, without connecting plates, etc. for repair to staircase,hand rails and back rest of over head reservoir , complete all as sepcified. [Note: All T&P and labour charges for working on OH tanks upto 21 mtr high staging deemed to be included in the quoted rate]

Lifting of defective submersible pump set any make & model of capacity 25 HP to 45 HP from deep well 350mm housing along with connected accessories such as column pipe of 150mm dia appx 30 m submersible cable, steel pipe, spider, sleeve, line shaft, nut, bolts etc complete all as specified and directed by Engr-In-Charge. [Note:- (i) All type of T & P, chain pulley & tripod etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate (ii) The Contractor will start the lifting work with in minimum time after getting message verbally/telephonically by JE E/M/AGE E/M. (iii) A penalty of Rs. 500/- per day will be imposed on the Contractor for wilful delay by the Contractor will be imposed as per opinion of Engineer-in-Charge and amount will be deducted from the due payment of the Contractor]

Transportation including loading & unloading of defective submersible pump set 3 phase any make and capacity 25 to 45 HP from pump house to work shop for necessary repair and transporting back to the pump house including carefully loading & unloading of pump set after repair complete all as specified and directed by Engr-In-Charge.

Dismantling of defective submersible pump set any make & model of capacity 25 HP to 45 HP, repairing the same including replacing old unserviceable parts and re-assembling and testing after repair complete all as specified and directed by Engr-In-Charge. [Note: (i) All the spares required for repair will be measured and paid seperately as supply only. (ii) Greasing of moving parts deemed to be included in the quoted rate]

Supply only CI/ MS bowl (As per existing size) for submersible pump capacity 25 HP to 45 HP any make & model complete all as specified .

All per item no.27 but Stainless steel shaft with key

All per item no.27 but Gun Metal Bush

All per item no.27 but Stainless steel sleeve.

All per item no.27 but Sand Guard

All per item no.27 but Impeller lock with key

All per item no.27 but Neck ring (as per existing size and type)

All per item no.27 but Turning & polishing of Pump shaft (lathe work)

Supply only Stainless Steel thrust bearing. parts for submersible motor of capacity 25 HP to 45 HP any make & model complete all as specified .

All per item no.35 but Carbon plate.

All per item no.35 but Rotor Gun Metal/steel bush

All per item no.35 but Rubber bush

All per item no.35 but Upper housing

All per item no.35 but Lower Housing

All per item no.35 but Turning, polishing of Rotor & shaft (Lathe work)

Rewinding of submersible motor capacity 25 HP to 45 HP any make & model with super enamelled copper wire of existing size including removal of existing burnt winding, cleaning of slots including packing material, connection and testing complete.

M&L for painting to pump set with two coat of synthetic enamel paint (grey colour) over a coat of red oxide primer after preparation of surface complete all as specified and directed by Engr-In-Charge.

Lowering, connecting, commissioning testing of repaired submersible set any make and capacity 25 HP to 45 HP 3 phase 415V into bore well 300/200mm with connected items such as column pipe approx 40 RM, properly connecting submersible cable etc complete all as specified and directed by Engr-In-Charge by Engineer-in-Charge. [Note:- (i) All type of T & P, chain pulley & tripod etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate (ii) The Contractor will start the lifting work with in minimum time after getting message verbally/ telephonically by JE E/M/ AGE E/M. (iii) A penalty of Rs. 500/- per day will be imposed on the Contractor for wilful delay by the Contractor will be imposed as per opinion of Engineer-in-Charge and amount will be deducted from the due payment of the Contractor]

Complete servicing of Fire fighting pump set any make & model of capacity 60 HP including replacement of minor spares and testing after servicing complete all as specified and directed by Engr-In-Charge. [Note: (i) Greasing of moving parts deemed to be included in the quoted rate (ii) All type of T&P main switch ,electric multi meter/ tong tester for fault detecting , etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.

Supply only rubber packing 6mm thick consisting of 8/6" holes for 100mm to 150 mm dia column pipe complete all as specified and directed by Engr-In-Charge.

Repair and maintenance of defective Monoblock motor pump any make & model of capacity 20 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling belt, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing including painting complete all as specified and directed by Engr-In-Charge. [Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.]

Repair and maintenance of defective Monoblock motor pump any make & model of capacity 10 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling Set, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing including painting complete all as specified and directed by Engr-In-Charge. [Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.]

Repair and maintenance of defective Monoblock motor pump any make & model of capacity 7.5 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling Set, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing complete all as specified and directed by Engr-In-Charge. [Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.]

Repair and maintenance of defective Monoblock motor pump any make & model of capacity upto 2.5 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling Set, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing including painting complete all as specified and directed by Engr-In-Charge. [Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.]

Periodical maintenance including complete servicing of Diesel Engine Generator set of 160 KVA capacity at Military Hospital of make: Kirloskar or any other make and connected accessories including replacement of oil /lubricant filter to keep the plant in running condition including routine maintenance complete all as specified and as directed. [Note: (i) The Contractor need to get the job done through authorised service centre/ agency of Kirloskar Oil Engine Ltd or any other OEM (Original Equipment Manufacturer) located near Faizabad. The cost thereof deemed to be included in the quoted rate. (ii) All Spare parts for routine maintenence will be measured and paid seperately under relevent items of this schedule as 'Supply Only' (iii) Labour charges for routine maintenance including properly dismantling of old parts deemed to be included in the quoted rate]

All as per item Ser No 47 here-in-before but of Diesel Engine Generator Set of 62.5/ 63 kVA capacity at Pump House No 1, 2, 3, 4, 5,6, 8, 9, 10, 11, 12, STP Himachal Niwas, STP Kandahar Line, Signal Centre, Amn Dump, Trolly Mounted

All as per item Ser No 47 here-in-before but of Diesel Engine Generator Set of 40 KVA capacity at Records

All as per item Ser No 47 here-in-before but of Diesel Engine Generator Set of 15 KVA capacity at Stn HQ

Supply only Cut out for routine maintenance of Alternator of DG Set 160 KVA, complete all specified.

All as per item no.55 but Ignition Switch

All as per item no.55 but Switch Plate

All as per item no.55 but Diode Plate

All as per item no.55 but Carbon

All as per item no.55 but Bulb Holder

All as per item no.55 but Rectifier Assembly

All as per item no.55 but Brush Box Assembly

All as per item no.55 but Bearing

All as per item no.55 but Oil seal

All as per item no.55 but Field Coil

All as per item no.55 but Lubricant oil filter for DG set 160 KVA

All as per item no.55 but Fuel filter (Pre) for DG set 160 KVA

All as per item no.55 but Fuel filter (Micro) for DG set 160 KVA

All as per item no.55 but Air filter for DG set 160 KVA

All as per item no.55 but Hose : Water Pump inlet to Radiator outlet for DG set 160 KVA

All as per item no.55 but Hose :Pipe to Water Pump for DG set 160 KVA

All as per item no.55 but Hose : Pipe to Diesal tank for DG set 160 KVA

All as per item no.55 but Hose pipe clip with nut

All as per item no.55 but terminal block for DG set 160 KVA

Supply only cut out for routine maintenance of Alternator of DG Set 15-62.5 KVA.

All as per item no.75 but Ignition Switch

All as per item no.75 but Switch Plate

All as per item no.75 but Diode Plate

All as per item no.75 but Carbon

All as per item no.75 but Bulb Holder

All as per item no.75 but Rectifier Assembly

All as per item no.75 but Brush Box Assembly

All as per item no.75 but Bearing

All as per item no.75 but Oil seal

All as per item no.75 but Field Coil

All as per item no.75 but Lubricant oil filter

All as per item no.75 but Fuel filter (Pre)

All as per item no.75 but Fuel filter (Micro)

All as per item no.75 but Air filter

All as per item no.75 but Hose : Water Pump inlet to Radiator outlet

All as per item no.75 but Hose :Pipe to Water Pump

All as per item no.75 but Hose : Pipe to Diesal tank

All as per item no.75 but Hose pipe clip with nut

All as per item no.75 but Terminal block

Supply only Coolant for DG Set

Supply only Lub Oil for DG Set of make Koel Care Premium Genuine

Supply only lead acid battery 12 volt 180 Ah including initial charge of make: Exide or equivalent complete all as directed by Engr-In-Charge

M&L for Automatic Voltage Regulator for DG Set of capacity 15 to 62.5/ 63 kVA make: Kirloskar or equivalent including taking out of old one.

M&L for Automatic Voltage Regulator for DG Set of capacity 160 kVA make: Kirloskar or equivalent including taking out of old one.

M&L for Calibration of Fuel Injection Pump including properly dismantling and transporting to service center/workshop for over hauling/ calibration and refixing on DG Set after calibration for DG Sets of capacity 160 kVA including taking out of old one and with replacement of following items all as directed by Engr -in charge : a) Element - 06 Nos b) D.V - 06 Nos c) T.R.B - 06 Nos d) Bearing - 02 Nos e) C.R - 01 Nos f) C.R Bush - 02 Nos g) Ball Bearing - 01 Nos h) F.P.P - 01 Nos i) F.P Kit - 01 Nos j) Pressure Bolt - 06 Nos k)Nozzle seal - 02 Nos l) Nozzle setting - 06 Nos & with all other neessary items .

All as per item Ser No 100 above but for DG Sets of capacity 62.5/ 63 kVA

All as per item Ser No 100 above but for DG Sets of capacity 40 kVA

All as per item Ser No 100 above but for DG Sets of capacity 15 kVA

M&L for Banjo Bolt M 14 x 1.5 including taking out of old one.

M&L for Flexible fuel pipe type 7.5 14 x 14 B 700 PB of make: Kirloskar or equivalent including taking out of old one.

M&L for Expansion bellow suitable for 62.5 kVA DG Set of make: Kirloskar including taking out of old one.

M&L for Starter Ring suitable for 160 kVA DG Set of make: Kirloskar or equivalent including taking out of old one.

M&L for Starter Ring suitable for 15 to 62.5 KVA DG Set of make: Kirloskar or equivalent including taking out of old one.

M&L for Fuel Pump mounted STOP solenoid switch suitable for 15 to 62.5-63 kVA DG set of make: Kirloskar or equivalent including taking out of old one.

M&L for Fan Belt suitable for 62.5 kVA DG set of make: Kirloskar or equivalent including taking out of old one.

M&L for servicing of radiator including cleaning and testing of leakages for DG set of capacity 15-62.5 KVA all as specified and as directedand [Note: - In case of leakages found during servicing, the same should be measured and paid separately ]

Dismantling the radiator and transporting to workshop, repair of all leakage and transporting back and refitting in original position and testing for DG set of capacity 15-62.5 KVA all as specified and as directed

M&L for Carefully dismantling the fuel tank and transporting to workshop, repair of all leakage, cleaning and transporting back and refitting in original position and testing after completion for DG set of capacity 62.5/ 63 kVA all as specified and as directed including taking out of old one.

M&L for Carefully cleaning of fuel tank for DG set of capacity 62.5/ 63 KVA all as specified and as directed including taking out of old one.

M&L for Carefully dismantling the self starter of DG set capacity 15-160 KVA and transporting to workshop and reffiting back after repair with replacement / repair of following items :

Supply only Carbon bush with spring materials for repair of self starter of DG set capacity 15-160 KVA , complete all specified.

All as per item Ser No 116 but GM Bush set

All as per item Ser No116 but Bendex Pinion

All as per item Ser No116 but Solenoid switch

All as per item Ser No116 but Armature Rewinding

All as per item Ser No116 but Field Coil set

M&L for rectification of leakage from 50mm bore GI Pipe line joints including excavation, returning and filling etc incl fittings like unions, sockets, bends, elbows, tees, nipples etc as required complete all as specified .

All as per item Ser No 122 but 40mm bore

All as per item Ser No 122 but 25mm bore

All as per item Ser No 122 but 20mm bore

All as per item Ser No 122 but 15mm bore

S&F 15mm bore Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed of make : Zolotov ,Leader, Venus , complete all specified.

All as per item Ser No127 but 20 mm bore.

All as per item Ser No127 but 25 mm bore.

All as per item Ser No127 but 50 mm bore.

Taking out unserviceable sluice valve 150mm bore from water mains

S&F connection & testing 150mm bore sluice valve 'ISI marked' both ends flanged and drilled cast iron body class PN-1.6 conforming to IS-14846/2000 complete with gun metal spindle of make : BIR, Upadhyaya, Leader, Kartar or equivalent including necessary nut bolts and gasket etc for fixing complete all as specified including taking down existing. [Note: For sluice valves fixed with pillars of over head tank, breaking of RCC/lead/ flange joints and repairing the same after fixing of valve deemed to be included in the quoted rates]

M&L for rectification of leakage from 150mm bore CI Pipe line of joints incl excavation in mud/soil and coucking with pig lead , returning filling , complete all specified.

Earthing complete with galvanised steel earth plate electrode 600 X 600 X 6mm thick buried directly in ground vertically to a depth not less than 2.25 meters deep below ground level with top edge of the earth plate not less than 1.5 meters deep below normal ground level, connected with and including galvanised iron strip of size 25 x 4mm connected to main test point as directed as earthing lead by means of nuts, bolts and washers of galvanised iron protected by 40mm dia (medium grade) GI tubing, funnel, wire mesh, 20mm bore GI tubing (light grade) watering pipe, including concrete pit in PCC (1:3:6) type C-1, precast RCC (1:2:4) type B-1 cover slab of size 350 x 350 x 50mm reinforced with 8mm dia TMT bars @ 15cm c/c in both ways and 10mm dia MS handle (01 No) of suitable size for lifting of cover slab, charcoal and salt in alternate layers including necessary excavation and earth work in soft/loose soil all as shown in Electric plate No 3 of SSR Part-I and testing on completion complete all as specified and directed by Engr-in-Charge.

Taking out steel water tubing/ UPVC for 20 mm bore size including fittings complete all as specified and directed.

S&F Unplasticised PVC pipes Sch 40 of fixed complete to walls, ceilings or in floors etc., any type of pipe for 15 mm bore sizes make: ISI Marked best quality etc complete all as specified and directed..

Repair and maintenance of suction sweeper comprising 600mm long MS/ CI fabricated suction head with PVC wheels, spring loaded brush and fibber squeezer including trolley mounted electric driven non clog self priming type centrifugal pumping set with 02 HP Motor 03 phase , 415 V electric driven DOL Push button starter along with repair to minor defects such as repair/ replacement to electric contact, kit-kat fuse, pumping set gland rope, coupling nuts & bolts, bush/ thrust bearing of existing size , push button, contactor block & relay of starter ,oiling/ greasing and testing etc complete including painting with two coat of synthetic enamel paint -of existing colour after removal of old paint / cleaning to rusted/ corrosive portion - 04 Sets [Note:- (i) All type of T&P main switch ,electric multi meter/ tong tester for fault detecting , etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate. (ii) If item of work is not got executed for any of the suction sweeper-machine , price adjustment shall be made based on the proportional rate worked out from unit quoted rate for the item of work. (iii) Supply of major items required for repair/replacement shall be measured and paid separately under relevant item of this schedule as 'supply only']

Supply only following Nylon-Rope size (14 -20) mm dia suction sweeper , complete all specified.

All as per item Ser No 138 above but Spire Brush suitable for Cleaning of swimming pool, complete all specified.

S & F PVC wheel with bush and nut bolt set of 04 nos suitable for suction sweeper machine all as specified and directed by Engr-In-Charge

Supply and fixing PVC Floats suitable for Swimming pool including taking out of old one

His And Her Enterprises

Khan Brothers

Hi-Tech Constructions

A ONE ENGINEERING

disha construction

Sai Ram Associates

M/S A P CONSTRUCTION