REPAIR/MAINT TO ROOF SHEET, CEILING AND ITS CONNECTED ITEMS, TILING, HARD STANDING, INTERLOCKING, PLINTH PAVEMENTS AND OTHER B/R ITEMS AND PERIODICAL SERVICES AND MISC B/R WORKS ZONE C AREA AT CH CC IN THE AREA OF AGE E/M (HOSP) UNDER GE E/M LUCKNOW

Amount

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by Engineer-in-Charge

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge

M&L for 100mm thick PCC 1:4:8 type D2 (using 40 mm graded stone agrregate) as in sub base floor etc complete all as specified and directed by Engineer-in-Charge

M&L for 40mm thick PCC type B-1 1:2:4 ( 20mm graded agg) finished fair and even using extra cement complete all as specified and directed by Engineer-in-Charge

S & F 6 to 8 mm TMT bars in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire [annealed] not less than 0.9 mm dia or scruing with clips complete all as specified and directed by Engineer-in-Charge

M&L TMT 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming Fe- 500 complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster from bricks or concrete surfaces not otherwise described including raking out joints, hacking for key and scrubing down with water etc complete all as specified and directed by Engineer-in-Charge

Temporarily blocking of inlet of septic tanks/manhole with suitable wooden plugs/gunny bags and pumping/bailing out effluent and taking out/removing the accumulated sludge soil sewage/any other foreign/foul materials etc (solid/semisolid) from the septic tanks/manholes. complete and cleaning the septic tank/manholes with water by mechanically/manually including taking out the blocking arrangements of inlet and making the system functional complete all as specified and directed by Engineer-in-Charge (NOTE: Depth of manhole/SOAK WELL/SEPTIC TANK exc 0.5 to 1.5M from below GL)

Temporarily blocking of inlet of septic tanks/manhole with suitable wooden plugs/gunny bags and pumping/bailing out effluent and taking out/removing the accumulated sludge soil sewage/any other foreign/foul materials etc (solid/semisolid) from the septic tanks/manholes. complete and cleaning the septic tank/manholes with water by mechanically/manually including taking out the blocking arrangements of inlet and making the system functional complete all as specified and directed by Engineer-in-Charge (NOTE: Depth of manhole/SOAK WELL/SEPTIC TANK exc 1.50M to 4.50M from below GL)

Temporarily blocking of sewage line with suitable wooden plugs/gunny bags and cleaning the same by rod-ding and removing the sludge alongwith brick bats/stones/broken bottles/any other foreign materials etc complete and cleaning the sewage line with water by mannually/mechanilly as directed by EIC, and taking out the blocking arrangements of inlet and making the system functional complete all as specified and directed by Engineer-in-Charge for 150 mm bore size of pipe lines

All as per item No 12 above but 200 mm bore

All as per item No 12 above but 300 mm bore

PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in coping and the like including weathering, slightly rounded or chamfered angles with & incl necessary use and waste of form work for fair faces of concrete complete all as specified and directed by Engineer-in-Charge

Supply only integral water proofing compound powder ISI marked complete all as specified and directed by Engineer-in-Charge

Mild steel work (ordinary grade Fe-310/410-0) as in small articles like angle iron framing work for manhole, rungs/steps in man hole complete all as specified and directed by Engineer-in-Charge

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished even & smooth without extra cement, cement mortar mixed with WPC @ 3% of weight of cement complete all as specified and directed by Engineer-in-Charge Note: WPC measured & paid for separately

15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished even & smooth without extra cement, cement mortar mixed with WPC @ 3% of weight of cement complete all as specified and directed by Engineer-in-Charge Note: WPC measured & paid for separately

Treating small articles of steel like MS rungs etc with coal tar black paint icl preparation of surface, area tarred not exc 0.1 sqm complete all as specified and directed by Engineer-in-Charge

Two coats of black bitumenous paint over a coat of red oxide zinc chrome primer including preparation of new steel surface not exceeding 10 cm width/girth complete all as specified and directed by Engineer-in-Charge

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed concrete to SGSW pipes of 300 mm bore dia incl packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and directed by Engineer-in-Charge.

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 200 mm bore dia incl packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and directed by Engineer-in-Charge

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 150 mm bore dia incl packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and directed by Engineer-in-Charge

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 300 mm bore dia incl packing under & completely surounding pipes with conrete after they are laid and tested complete all as specified and directed by Engineer-in-Charge

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 200 mm bore dia incl packing under & completely surounding pipes with conrete after they are laid and tested complete all as specified and directed by Engineer-in-Charge

PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in concrete bed to SGSW pipes of 150 mm bore dia incl packing under & completely surounding pipes with conrete after they are laid and tested complete all as specified and directed by Engineer-in-Charge

Salt-glazed stone ware drain (SGSW) pipe grade 'A' 150 mm bore dia laid in trenches & jointed in CM 1:1 complete all as specified and directed by Engineer-in-Charge.

Salt-glazed stone ware drain (SGSW) pipe grade 'A' 200 mm bore dia laid in trenches & jointed in CM 1:1 complete all as specified and directed by Engineer-in-Charge

Salt-glazed stone ware drain (SGSW) pipe grade 'A' 300 mm bore dia laid in trenches & jointed in CM 1:1 complete all as specified and directed by Engineer-in-Charge.

M&L 150mm PCC 1:2:4 type B2 using 40mm graded aggregate laid over 150mm th hardcore of broken boulders of gauge exe 63mm but n exe,100mm deposited, spread and levelled in layers n exc 15 cm thick watered and rolled/ rammed to a true surface over rammed earth as in road/pavement cutting , complete all as specified and directed by Engineer-in-Charge

M&L RCC M30 nominal mix as in slabs suported on walls,beams and coluumns in floors, roofs, landings, balconies, canopuies, deck slabs and shelves and the like ans coumns fair finished in necessary provision for opening Man hole and precast cover slab complete all as specified and directed by Engineer-in-Charge

M&L use and waste of form work to soffits os suspended slabs such as roof slabs, floor slabs, landings and similar work; not eceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge

Cast iron 150mm dia pipes S/S including specials Class LA supplied and laid and fixed in RCC Flush Out Tanks complete all as specified and directed by Engineer-in-Charge

Cutting salt -glazed stoneware drain pipe in position, including jointing socket end of new pipe to same with packed spun yarn and cemnet mortar 1:1 for 150mm dia SGSW pipes, complete all as specified and directed by Engineer-in-Charge

Taking up or down steel tubing and connections , including cleaning for re-fixing or removal of store, 15 mm bore complete all as specified and directed by Engineer-in-Charge

Taking up or down steel tubing and connections , including cleaning for re-fixing or removal of store, 20 mm bore complete all as specified and directed by Engineer-in-Charge

Refixing old steel tubing and connections in new or old position ( walls, ceiling , floors, etc.)15 mm nominal bore complete all as specified and directed by Engineer-in-Charge

Refixing old steel tubing and connections in new or old position ( walls, ceiling , floors, etc.)20 mm nominal bore complete all as specified and directed by Engineer-in-Charge

M&L 15 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge

Dismantling water tank capacity exc 250 & n.exc 500 ltr and taken as credit complete all as specified and directed by Engineer-in-Charge

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 500 litres complete all as specified and directed by Engineer-in-Charge

Dismantling water tank capacity exc 500 & n.exc 1000 ltr and taken as credit complete all as specified and directed by Engineer-in-Charge

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 1000 litres complete all as specified and directed by Engineer-in-Charge

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. .(Minimum weight 20mm-210gms) complete all as specified and directed by Engineer-in-Charge

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-Charge

Providing and fixing of E-board 'Everest' make 600x600x4mm thick white prelaminated seif embosed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24 mm wide T-section/Angle sect complete all as specified and directed by Engineer-in-Charge

M&L Suspended ceiling, comprising 12.5 mm thick reinforced gypsum plaster boards Conforming to IS-2095 , GI perimeter channels, intermdiate channels, etc. including finishing the exposed surfaces with Oil bound distemper two coats complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frame (wooden/aluminium) n. exc. 1.5 Sqm each with shutters (with out taking off shutters from the frame) and taken as credit complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames (wooden/aluminium) with shutters without taking off shutter from the frames exc. 1.5 but n. exc 4 sqm each complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description n exc 1 sq.m each complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each complete all as specified and directed by Engineer-in-Charge

PVC door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with MS square tube, suppling & fixing in opening as per specn & drg complete all as specified and directed by Engineer-in-Charge

S &F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm with stuck inside with complete all as specified and directed by Engineer-in-Charge

S&F 250 mm aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 100 mm length of bolt complete all as specified and directed by Engineer-in-Charge

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed by Engineer-in-Charge

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed by Engineer-in-Charge

S & F in repair for 150 mm floor door stopper of aluminium alloy body and tonge,anodised with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge

Hacking out old broken glass, any thickness, size, quality, or description, from frame nexc 1.5 Sqm each pane complete all as specified and directed by Engineer-in-Charge

S&F for 3.0 mm thick sheet glass ordinary quality and glazing with oil putty nexc 0.5 Sqm each pane complete all as specified and directed by Engineer-in-Charge

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty n.exc 0.5 Sqm each pane complete all as specified and directed by Engineer-in-Charge

S&f for 4.8 mm thick sheet glass odinary qulity and glazing with neosprene beading n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge

S&F in repairs Chromium plated fancy long body Bib taps with cup , cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair cast iron floor trap with chromium plated grating including jointing to waste pipe wih cement mortar (75 mm bore of pipe) complete all as specified and directed by Engineer-in-Charge

S&F in repairs Brass chromium plated shower rose without swivel joints , any size, including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge

S&F in repairs Chromium plated ,Concealed stop cock Reduced body ISI Marked, , cast copper alloy, screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed by Engineer-in-Charge

S&F in repair CP Angle stop cock ( one way) long thread with wall flange , fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed by Engineer-in-Charge

S&F in repairs PTMT (Polytetra Methyllene Terephthalate) Bib taps suitable for 15 mm bore pipe standard of PTMT any colour screwed, for iron pipe and fixed ( Minimum weight 15 mm-90 gms complete all as specified and directed by Engineer-in-Charge.

S&F in repairs CP Angle stop cock( two way) long thread with wall flange , screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed by Engineer-in-Charge .

S&F in repairs CP mild steel gratings suitable for 75/100 mm dia NT/ FT complete all as specified and directed by Engineer-in-Charge

S&F in repairs Chromium plated Brass Tubular towel rod, of 24" (60 cm long) complete all as specified and directed by Engineer-in-Charge

S&F in repair vitreous China wash down water closet pan ( padestal pattern Water Closet Cat No.20012, white) , ( excluding fixing bolts, flushing cistern and flush pipe) , including connection to drain ( or outgoing pipe) and to flushing pipe , etc., complete all as specified and directed by Engineer-in-Charge

S&F in repairs VC WHITE Squatting pan ,'Orissa' pattern size 580x440mm with integral footrests water closet) with 'P' or 'S' trap front or back inlet complete including lime concrete for bedding, connection to drain pipe and to flushing pipe , anti syphon complete all as specified and directed by Engineer-in-Charge

S&F in repairs Low level flushing cistern, moulded from virgin poly propylene complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs Plastic water closet seat, white, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-Charge

S&F in repairs PTMT connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer-in-Charge

S&F Vitreous China bowl urinal flat back, size of 465x355x265 mm White ( minimum), with grating and union for discharge pipe ( excluding flushing cistern, flush pipe , and waste pipe) , fixed in repairs including connections to flushing pipe and outgoing complete all as specified and directed by Engineer-in-Charge

S&F in repair vitreous china wash basin (WHB) , white , flat back , size 550mmx400mm including brackets, waste fittings , brass Chromium plated for glazed basins etc. with long screw shanks and fly nuts , flange end embedded in red lead cement , including cutting complete all as specified and directed by Engineer-in-Charge

S&F 32mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified and directed by Engineer-in-Charge

M&L in repairs 32 mm waste fittings , brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-Charge

S&F in repairs 32 mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified and directed by Engineer-in-Charge

S&F in repair Gun metal , globe or gate valves, with iron wheel head, screwed both ends for 20 mm bore dia. iron pipe and fixed complete all as specified and directed by Engineer-in-Charge

S&F Gun metal, in repair globe or gate valves, with iron wheel head, screwed both ends for 15 mm bore dia. iron pipe and fixed complete all as specified and directed by Engineer-in-Charge

S & F Neosprene rubber beading including taking down old rubber beading as in aluminium window and door shutter complete all as specified and directed by Engineer-in-Charge

S&f for 12 mm thick sheet glass odinary qulity and glazing with neosprene beading of any size any postition complete all as specified and directed by Engineer-in-Charge

Repairing of existing aluminium door single/double leaf including oiling and greasing of floor springs,replecing of rubber beading if required,replacement of hinges,handle,towerbolt of any size any type present at site on required basis,also including replacement of any membre of aluminium section i.e frame & shutters membre and 5-12 mm glass and making the door and shutter serviceable complete all as specified and directed by Engineer-in-Charge.(Floor door springs where renewed shall be measured and paid separately under appropriate

Repairing of existing toughend glass door single leaf including oiling and greasing of floor springs,replacement of hinges,handle,lock of any size any type present at site on required basis,also including replacement of any membre of aluminium section i.e frame & shutters membre and 12 mm glass and making the door and shutter serviceable complete all as specified and directed by Engineer-in-Charge.(Floor door springs where renewed shall not be measured & paid seperately it includes the rate of floor spring also)

Supply & fixing in repair Double action floor spring hydraulically regu-lated made up of minimum 1.25 mm thick alu-minium alloy sheet foun-dation box,main body with stainless steel cover, governing pivot made of mild steel heavy duty fixed complete all as specified and directed by Engineer-in-Charge

S&F in repairs Aluminium body ( extruded section ) body Door closer hydraulically regulated, designation No. 2 , universal type , suitable for door shutters 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed complete all as specified and directed by Engineer-in-Charge

S&F in repair for 100 mm mild steel 4 lever mortice lock vertical type of size complete all as specified and directed by Engineer-in-Charge

S&F in repair for Aluminium Anodised window, ventilator fixed type shutter, aluminium section weighing 0.55 Kg/m incl necessary joining cleats, glazing clips rubber neoprene packing , Handle 2 Nos in each door, hinges, anodised aluminium snap beading screw, complete all as specified and directed by Engineer-in-Charge

S&F in repair for Aluminium Anodised door shutters, aluminium section weighing 0.55 Kg/m incl necessary joining cleats, glazing clips rubber neoprene packing , Handle 2 Nos in each door, hinges, anodised aluminium snap beading screw, complete all as specified and directed by Engineer-in-Charge

S &F in repair aluminium partition with pre-laminated particle board at bottom panel and 5.5.mm thick glass on top panel incl glazing clip and neosprene rubber beading complete all as specified and directed by Engineer-in-Charge

S&F Aluminium Anodised ventilator curved shaped fixed with reflective type glass aluminium section weighing 0.55 Kg/m incl necessary joining cleats, glazing clips rubber neosperene at bottom pannel and top panel with wire cloth of 0.46 nominal dia of wire and average width of aperature 1.4 mm complete all as specified and directed by Engineer-in-Charge

S&F Aluminium grill 6mm dia not less than 4 Kg per sqm fixed with frame in windows/ventilator complete all as specified and directed by Engineer-in-Charge

S&F Anodised Aluminium alloy sections sliding windows shutters with frames comprising Series -C (20mm), 2 track sliding shutters duly fitted with neoprene beading, glazing clips,locking device, heat absorbing glass 4.8 mm nominal thicknes complete all as specified and directed by Engineer-in-Charge

S&F for Aluminium Anodised door frame with shutter, incl necessary joining cleats, glazing clips rubber neoprene packing , Handle 2 Nos in each door, 4 Nos 100mm hinges, 1 Nos 200mm aluminium anodised tower bolt anodised aluminium snap beading screw ecessary locking arrangement with mortice lock with duplicate complete all as specified and directed by Engineer-in-Charge

S&F Aluminium designer guard bars with 90 cm height and 50mm dia pipe for railing of verandah complete all as specified and directed by Engineer-in-Charge

S&F 35 mm thick factory made Flush shutters , solid core construction , with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer-in-Charge

M&L 18-20 mm thick granite stone slab ( Black colour) , bedded over screed bed and jointed in cement mortar to match the colour of slab as in flooring , polishing and grinding complete all as specified and directed by Engineer-in-Charge. (Screeding bed shall be measured and paid separately)

M&L for glazed ceramic tiles in vertical surfaces 350 x 250 x 7 mm / 450 x 350 x 7 mm [thick] set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including 10mm thick screed in CM 1:3 complete all as specified and directed by Engineer-in-Charge

Repairing of existing UPVC door single/double leaf including oiling and greasing of floor springs,replecing of rubber beading if required,replacement of hinges,handle, lock,towerbolt of any size any type present at site on required basis,also including replacement of any membre of aluminium section i.e frame & shutters membre and 5-12 mm glass and making the door and shutter serviceable complete all as specified and directed by Engineer-in-Charge(any items required regarding repair where renewed shall not be measured and paid separately.)

S&F in repair power coated anodised Aluminium alloy sections sliding windows shutters with frames comprising Series -C (20mm), 2 track sliding shutters duly fitted with neoprene beading, glazing clips,locking device, heat absorbing glass 4.8 mm nominal thicknes complete all as specified and directed by Engineer-in-Charge

S&F in repair Powder coated Aluminium sections ( conforming to IS) door frames with double leaf shutters complete duly fitted with neosprene rubber beading,heat absorbing glass panes 4.8 mm nominal thickness, Alu anodised with rubber shoe floor door stoppers- 2 Nos, 100mm aluminium hinges 4 Nos per shutter, Handle 2 Nos in each shutter, Aluminium tower 1 Nos in each shutter and necessary locking arrangement with mortice lock with duplicate key complete all as specified and directed by Engineer-in-Charge

S&F in repair Powder coated Aluminium sections ( conforming to IS) door frames with single leaf shutters complete duly fitted with neosprene rubber beading,heat absorbing glass panes 4.8 mm nominal thickness, Alu anodised with rubber shoe floor door stoppers- 1 Nos, 100mm aluminium hinges 4 Nos per shutter, Handle 2 Nos in each shutter Aluminium tower 1 Nos in each shutter and necessary locking arrangement with mortice lock with duplicate key complete all as specified and directed by Engineer-in-Charge

S&F Aluminium grill 6mm dia not less than 4 Kg per sqm fixed with frame in windows/ventilator complete all as specified and directed by Engineer-in-Charge

Excavating in post holes each not exc. 0.5 cum getting out in soft / loose soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc. 25 cm, watering and removing surplus soil to a distance not exc. 50 m and depositing where complete all as specified and directed by Engineer-in-Charge

M&L for PCC 1:4:8 type D-2 as in foundation and mass concrete using 40 mm graded stone complete all as specified and directed by Engineer-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge

M&L for preparing new steel steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge

S&F in 0.50 mm Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting made to any shape or Semi-ciruclar any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge

S&F 2mm thick fibre glass reinforced transclucent corrugated sheeting with two corrugations side lap fixed with L type or J- type or cranked hook bolts and washers in roof, wall etc complete all as specified and directed by Engineer-in-Charge

M&L for providing cement concrete type B-1, 1:2:4 (20 mm graded aggregate ) as in roof kerbs /padding or similar work or mud stops rounded or chamferred on edges complete all as specified and directed by Engineer-in-Charge

S&F 6mm thick hollow polycarbonite sheet as in roofing including fixing clips etc complete all as specified and directed by Engineer-in-Charge

M&L in repairs hand shower HSH -1717 of jaquar or equivalent all as pecified and as directed including fitting to 15mm bore GI pipes complete all as specified and directed by Engineer-in-Charge.

M&L in repairs over shower HSH -1989 of jaquar or equivalent all as pecified and as directed including fitting to 15mm bore GI pipes complete all as specified and directed by Engineer-in-Charge.

M&L in repairs shower arms SHA 477 of jaquar or equivalent all as pecified and as directed including fitting to 15mm bore GI pipes complete all as specified and directed by Engineer-in-Charge.

M&L in repairs shower pannels thermostatic mixer chrome code GFL-CHR-GR000B1H00X with 3 adjustable vertical jets for massaging the neck, waiste and thighs of jaquar or equivalent all as pecified and as directed including fitting to 15mm bore GI pipes complete all as specified and directed by Engineer-in-Charge

M&L in repairs EWC with flushing cistern seat covering including fixing and all complete of KUS-WHT-0203 series of jaquar or equivalent complete all as specified and directed by Engineer-in-Charge

M&L in repairs Wash hand basin of KUS-WHT-0553 series of jaquar or equivalent complete all as specified and directed by Engineer-in-Charge

S& F in repairs 15mm dia single lever wall mixer with proviision of Hand shower but without hand shower of Jaquar LYR-38119 or equivalent complete all as specified and directed by Engineer-in-Charge

S&F in repairs 15mm Bib cock with wall flange LYR-38037 of Jaquar or equivalent complete all as specified and directed by Engineer-in-Charge

S&F in repairs 15mm two way Bib cock with wall flange LYR-38037 of Jaquar or equivalent complete all as specified and directed by Engineer-in-Charge

S&F in repairs 15mm Angular stop cock with wall flange FON-40053 of Jaquar or equivalent complete all as specified and directed by Engineer-in-Charge

S&F in repairs 15mm Pillar cock with 200mm extension FLR-5021N of Jaquar or equivalent complete all as specified and directed by Engineer-in-Charge

M&L in repairs Central hole basin Mixer without popup waste system with 450mm long braided hoses CON-167KNB of jaquar or equivalent complete all as specified and directed by Engineer-in-Charge including fitting to 15mm bore GI pipes.

M&L in repairs single towel rail 600mm long AKP-35711P of Jaquar or equivalent complete all as specified and directed by Engineer-in-Charge

M&L in repairs soap dish AQN-7731 of jaquar or equivalent complete all as specified and directed by Engineer-in-Charge including fitting to 15mm bore GI pipes.

Anti-Microbial Protection: These product hygiene coatings start the bio cidal action as soon as the microorganism land on the surface, and prevents the growth of mould, bacteria and yeasts for at least 5 years. This Hygiene coating are independently tested by leading universities to demonstrate resistance. Note : (Anti-Microbial Protection: Filling of all Joints and cavities and Sanded Flush to provide a joint less finish and then sprayed with a water based liquid plastic aseptic and self sterilizing wall coating system to a d.f.t. of 300 microns with primer. These hygiene coatings should start the biocidal action as soon as the microorganism land on the surface, and prevent the growth of mould, bacteria and yeasts for at least 5 years. complete all as specified and directed by Engineer-in-Charge Make SIKKA ( Formally Liquid Plastic)

Conductive Flooring: 2mm thick Conductive flooring with carbon backing total thickness 2.00mm, total weight 3.000 g/m2 polyurethane reinforced ,scratch resistant, fire resistant, chemical resistant , slip resistant, anti fungi & bacterial growth , dimensional stability 0.40%, static electrical charger < 2Kv , impact sound reduction approx +4bd, electrical resistant. Installation : The flooring would be installed on a smooth, clean sub floor which should be free from any undulation .A copper strip/mesh should be layer under the tiles, with one earthing point for every 150 sft of area and good quality water based adhesive for fixing as per as manufacturers recommendation. Thermal Welding : The joints must be welds by the heat fusion process to get a seamless floor. The joints in the flooring should be sealed by using a PVC welding bar of matching color to be supplied by the manufacturer, using a hot air gun for fusion of welding bar with flooring. The same application to be done for wall skirting up to max 150mm and coving to be provided using appropriate material and method complete all as specified and directed by Engineer-in-Charge. Make – Gerfloor/ Tarquet , France

M&L 8-10mm thick wall tiles in repairs Duracrete manufactured by M/S Intex Designer Tiles Pvt Ltd. or equivalent of other specified make ) as invertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10mm thick screed in CM 1:3 complete all as specified and directed by Engineer-in-Charge

M&L in repairs for designer/degital wall tiles in vertical surfaces 7mm thick and area exc 0.13 Sqm and not exceeding 0.18 Sqm each set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10mm thick screed in CM 1:3 complete all as specified and directed by Engineer-in-Charge

M&L in repairs 22 mm thick floor tiles ( Duracrete manufactured by M/S Intex Designer Tiles Pvt Ltd. or equivalent of other specified make ) as in floor/path etc. set over 20mm thick screed bed in CM 1:4 and jointed in neat cement slurry and pointed with polymer based cementious tile jointing filler complete all as specified and directed by Engineer-in-Charge (Note : Screed bed will not be measured and paid separately)

Dismantling fencing wire,any type complete all as specified and directed by Engineer-in-Charge

Mild steel work as in angle iron fencing posts, struts including cutting, tops to shape as directed, bent to shape, drilling holes, notching for wire etc including all necessary bolting or riveting etc and embedding in concrete complete all as specified and directed by Engineer-in-Charge

Mild steel flat iron supports for posts/struts for securing fencing (chain link) using MS rods including drilling holes, notching for wire etc complete all as specified and directed by Engineer-in-Charge

Mild steel screw bolts (machine made) of 10 mm dia of sank withhexagonal or squre head at one end & screw the other or screwed both end (as directed)each screwed end to be fitted with washer and one hexagonal or square nut n exc 5 cm long complete all as specified and directed by Engineer-in-Charge

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed by Engineer-in-Charge.

Supply only chain link MS galvanised fencing of size 100x100mm, 3mm dia complete all as specified and directed by Engineer-in-Charge

Supply only 4mm dia plain mild steel wire, galvanised class 3 , in fencing including straining and fixing to steel posts and/or to straining bolts complete all as specified and directed by Engineer-in-Charge. (each line of wire to be measured)

S&F Expanded metal, cut to length , bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia.or fixing with galvanised steel staples supplied and fixed complete to wood or steel members (not exc 4 Kg/sqm) complete all as specified and directed by Engineer-in-Charge

S&F for M S work as in Hand rails, half round or other stock section or core for wooden hand rail straight portion, drilled and countersunk for balusters, nosing to steps including embeding in concrete and securing bolts for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc fillets including all necessary drilling bolting or reveting etc and similar work conforming Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge

S&F for M S work asFramed works such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes,framed guard bars barred iron doors ladders, framed balusters walk ways railing, framed work of water tanks, framed and hung as gates including pintle hinges, stops, hand made sliding sliding bolts etc complete all as specified and directed by Engineer-in-Charge

M&L in repair for 3mm thick ACP sheet wooden finish along with almuminium frame work and making groove and shelf complete all as specified and directed by Engineer-in-Charge

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge

All as per item No. 151 above but on ceiling.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint/shade complete all as specified and directed by Engineer-in-Charge

All as per item No 153 above but two coats

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade complete all as specified and directed by Engineer-in-Charge

All as per item No.155 above but two coats

All as per item No 155 above but on ceiling.

Preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Complete removal of existing treatment of walls and applying two coats of distemper oil emulsion over a coat of Birla or JK white wall putty average thickness 2mm on old plastered surfaces including prepration complete all as specified and directed by Engineer-in-Charge

M & L preparation of old brick, stone, concrete, AC or decorated plastered surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

M&L for writing letters or figures (Block, Roman Italic or Indian) n exc 30 cm high with a thick coat of synthetic enamel paint without showing signs of brushes mark complete all as specified and directed by Engineer-in-Charge

M&L for stops, commas, short lines, dashes, hyphens, brackets etc complete all as specified and directed by Engineer-in-Charge

M&L applying one coats of Apex ( Asian Paint) / Weather coat (Berger) over old painted surface including preparation of wall surface complete all as specified and directed by Engineer-in-Charge

M&L for rendering 10 mm thick on brick work/ concrete surfaces in cement mortar 1:6 on fair faces finished fair & even complete all as specified and directed by Engineer-in-Charge

M&L for 15 mm thick rendering in CM 1:4 on fair faces of brick work surface finished even and fair without using extra cement complete all as specified and directed by Engineer-in-Charge (Note : Integral WPC shall be measured and paid seprately )

Supply only integral WPC of approved quality complete all as specified and directed by Engineer-in-Charge

M&L rendering 5 mm thick on concrete surfaces in ceiling , in cement and sand mortar 1:3 complete all as specified and directed by Engineer-in-Charge

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying three coats white wash complete all as specified and directed by Engineer-in-Charge

Preparation of newly plastered surfaces and applying two coat of oil bound disemper over one coat of oil base primer all as specified on walls surface.Incl a coat of 3mm wall care putty complete all as specified and directed by Engineer-in-Charge.

M&L applying one coats of plastic emulsion paint interior quality any shade over old painted surface including preparation of wall surface complete all as specified and directed by Engineer-in-Charge

M&L Preparation of newly plastered or unplastered surfaces of walls by brooming down and priming plastered and other surfaces with cement paint primer ( before application of cement base paint) including two coats of cement base paint complete all as specified and directed by Engineer-in-Charge

M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying two coats white wash complete all as specified and directed by Engineer-in-Charge

Dismantling of asbestos cement (corrugated, semicorrugated etc) sheets including ridges in roof covering complete all as specified and directed by Engineer-in-Charge

S&F steel work in tubular trusses/posts including special washers etc complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St-240 complete all as specified and directed by Engineer-in-Charge

M&L for 100 mm thick PCC 1:5:10 type D2 (using 40 mm graded stone agrregate) as in sub base floor etc complete all as specified and directed by Engineer-in-Charge

M&L for 75 mm thick PCC 1:2:4 type C2 (using 40 mm graded stone agrregate) as in sub base floor etc complete all as specified and directed by Engineer-in-Charge

M&L for filling joints between two panels with mix of 85/25 bitumen and sand in 1:3 complete all as specified and directed by Engineer-in-Charge

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as plinth protection/path and the like complete all as specified and directed by Engineer-in-Charge

M&L for cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in coping,padding and bed block, wall through and the like including weathering slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed by Engineer-in-Charge

M&L 18-20mm thick machine cut Kota stone slab flooring with marble stone strips/ slab/ tiles as per design approved, over and including cement screed bed 15mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed by Engineer-in-Charge (Note : Screed bed will not be measured and paid separately)

M&L 18-20mm thick machine cut Kota stone slab as in skirting /riser over cement screed bed 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed by Engineer-in-Charge (Note : Screed bed will not be measured and paid separately)

S&F for M S work asFramed works such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes,framed guard bars barred iron doors ladders, framed balusters walk ways railing, framed work of water tanks, framed and hung as gates including pintle hinges, stops, hand made sliding sliding bolts etc complete all as specified and directed by Engineer-in-Charge

Demolition of floor hearth or wall tiling including cement mortar bedding (But not backing) removeing serviceable tiles to store and rubbishoff the premishes complete all as specified and directed by Engineer-in-Charge

M&L for non skid ceramic tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.16 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 15mm thick screed complete all as specified and directed by Engineer-in-Charge (Note : Screed bed will not be measured and paid separately)

M&L Vitrified ceramic tiles 10mm thick (square/ractangular) Coloured polished tiles, area of each tile n.exc 0.38 sq m in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement and pigment to match over 15 mm thick screeding (Note : Screed bed will not be measured and paid separately) complete all as specified and directed by Engineer-in-Charge

S&F aluminium alloy wire cloth, 0.45 mm nominal dia of wire and averaging width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed by Engineer-in-Charge

S&F in repair aluminium alloy wire cloth, 0.45 mm nominal dia of wire and averaging width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of wall and applying two coats of distemper oil emulsion over a coat of Birla or JK white wall care putty average thickness 2 mm on old plastered surface including washing floors, cleaning glass, joinery,electrical fittings, wiring etc of drops and splashes complete all as specified and directed by Engineer-in-Charge

M & L Reinforced Cement concrete 1:2:4 Type B-1 using 20mm graded stone aggregate as in slabs supported on walls and in shelves etc and the like complete all as specified and directed by Engineer-in-Charge

M & L Form work to soffits of suspended slabs, floor slabs, landings and similar work; not exceeding 200 mm thick fair finished flat complete all as specified and directed by Engineer-in-Charge

S & F TMT reinforcement bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. Or securing with clips complete all as specified and directed by Engineer-in-Charge

M&L 18-20 mm thick granite stone slab ( Black colour) , bedded over screed bed and jointed in cement mortar to match the colour of slab as in flooring , polishing and grinding complete all as specified and directed by Engineer-in-Charge ( Screeding bed shall be measured and paid separately)

M & L 15mm thick screed plaster on RCC slab CM 1:4 with using water proofing compound @ 3% by weight of cement complete all as specified and directed by Engineer-in-Charge ( WPC to be measured and paid separately)

M/S AMARJIT SINGH