GE/SRA/T-27/2025-26

Amount

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Paving, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L for Cement Concrete 1:4:8 type D2 (40mm Graded Stone Aggregate), 100mm thick, as in Sub-bases of floor, path, hardstanding etc complete all as specified and directed.

M&L for Cement Concrete 1:3:6 type C2 (40mm Graded Stone Aggregate), 75mm thick, as in plinth protection finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for laying 60mm thick factory made pre-cast cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, laid in required pattern over compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and removing from site complete all as specified and directed. (NOTE: Sand cushioning shall be measured and paid separately)

M&L for sand filling under floors or in foundation incl watering and consolidation complete all as specified and directed.

M&L Providing, cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping finished even and smooth without using extra cement complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, plain, etc.) sheets in roof/wall coverings and removal from site complete all as specified and as directed.

Dismantling of fibreglass/polycarbonate roofing sheet (corrugated, semi corrugated, plain, etc.) sheets in roof/wall claddings etc and removal from site complete all as specified and directed.

S&F 2mm thick Polycarbonate sheet, drop embossed design, density 1.2 kg/m3, in any colour, as in wall claddings/roofs including necessary side or end laps duly fixed with coach screws and washers complete all as specified and directed.

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

All as per Item No. 10 above but 0.50 mm thick coloured plain galvalume sheet as in ridge/valley gutter of roof.

Dismantling structural steel work of any description in rafters, purlins and wind ties etc and removal from site complete all as specified and directed. NOTE: If the planned MS structure, truss, etc is different from the existing structure, proper measurement of the existing structure to be demolished, shall be recorded in MB duly signed by the Engineer-in-Charge.

M&L for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 or RHS/SHS Sections conforming to IS 4923:1997 grade YST 210 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. No extra measurement for the same will be considered except for base plates at top & bottom of columns)

M&L for preparing New or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and directed.

Demolition of Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc. Incl removal of debris from site complete all as specified and directed.

M&L for Brick Work with Fly-Ash Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and directed.

M&L Brick work using Serviceable Bricks obtained from Item No. 15 here-in-before including removing old Mortar, Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in cement mortar 1:6, complete all as specified and directed.

M&L for complete removal of existing treatment on old painted/distermpered surfaces of walls by scrapping and removing layers of all wall finishes including cleaning, watering to make the surface clean and free from dust, etc including necessary scaffolding, safety and protective measures complete all as specified and directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls/Concrete Surfaces, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L for preparing New/Undecorated Plastered Surfaces of Walls, applying a coat of suitable cement primer followed by a Coat of 2.0 mm thick Wall Putty (in two layers of 1mm thick) including rubbing down with Sand Paper to obtain a smooth finish surface and finishing with Two Coats of Acrylic/Oil Bound Distemper (as approved) as per desired shade/tint complete all as specified and as directed.

M&L for Rendering (Ceiling) 5.0mm thick in Cement Mortar 1:3 on Concrete Surfaces as in Ceiling, etc., Plastered Surfaces finished Even and Smooth, without using Extra Cement, complete all as specified and as directed.

M&L for Rendering (Ceiling) 10.0mm thick in Cement Mortar 1:3 on Concrete Surfaces as in Ceiling, etc., Plastered Surfaces finished Even and Smooth, without using Extra Cement, complete all as specified and as directed.

M&L for Preparing Newly Plastered Surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and directed.

M&L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed with with water proofing compound (as per manufacturer's instructions) on external surfaces of brick/stone walls or concrete surfaces finished even and fair upto 4 storey height including necessary scaffloding complete all as specified and directed. Note : Water Proofing compound shall be measured and paid seperately as "Supply only".

Supply only Liquid Water Proofing Compound, conforming to IS and/or as approved, complete all as specified.

M&L for preparation of newly plastered surfaces and finished with two coats of exterior acrylic emulsion paint (having anti-dust & anti-algae properties) duly mixed with stainer to achieve approved Tint/shade (in camouflage pattern) over a coat of suitable exterior primer, applied to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufacturer's instructions, up to 4 storey height incl necessary scaffolding safety gear etc complete all as specified and directed.

M&L for Rough Cast Plaster on Brick Walls consisting Under Coat of Cement and Sand Mortar 1:3 not less than 10mm thick and while it is still in Plastic state the Rough Cast Mixture consisting of Crushed Stone or Fine Gravel mixed with Coarse Sand and Cement in the ratio 1:1:1 shall be applied and finish Even, complete all as specified and directed.

M&L preparing newly Rough Cast plastered surfaces of Walls and applying two Coats of Exterior Emulsion Paint (having anti-dust & anti-algae properties) duly mixed with stainer to achieve approved Tint/shade (in camouflage pattern) over a coat of suitable exterior Primer (as per Manufacturer's instructions), complete all as specified and directed.

M&L preparing old Distempered surfaces of Walls/cement boards including filling the existing Nails/Screw Holes, etc with putty and making surfaces smooth and applying One Coat of Acrylic Distemper / Oil Bound Distemper (of approved tint) with rollers complete all as specified and directed.

M&L preparing old Distempered surfaces of Walls/cement boards including filling the existing Nails/Screw Holes, etc with putty and making surfaces smooth and applying Two Coats of Acrylic / Oil Bound Distemper (of approved tint) with rollers complete all as specified and directed.

M&L for preparing old treated/decorated surfaces of walls and applying One Coat of White Wash, complete all as specified and directed.

M&L for preparing old treated/decorated surfaces of walls and applying Two Coats of White Wash, complete all as specified and directed.

M&L for preparing old treated/decorated surfaces of ceilings and applying One Coat of White Wash, complete all as specified and directed.

M&L for preparing old treated/decorated surfaces of ceilings and applying Two Coats of White Wash, complete all as specified and directed.

Dismantling of ceiling grid frame, any type along with ceiling board of any thickness including cover fillets complete all as specified and directed.

Dismantling of wall boards, any type as in lining, panelling etc, of any gauge or any thickness including cover fillets, setting aside for re-use or removal from site complete all as specified and directed.

S&F false ceiling with powder coated exposed G.I. grid suspension system consisting of Main Runner 3600 mm long, Cross Tee 1200mm/600mm long and Wall Angle, wall angle fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c, Main Runners placed @ 1200mm, Cross Tee 1200mm inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm and additional cross tees of 600 mm placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600mm x 600mm, grid of module size 600mm x 600mm shall be supported by 6 mm dia G.I. wire from purlins/soffit complete all as specified and directed. Note: Ceiling board will measured and paid separately under appropriate item.

All as per item No. 38 above, but except material (Serviceable GI snap grid obtained from item No. 36 here in before) complete all as secured and directed. Note: Ceiling board shall be measured separately under appropriate item.

S&F 12 mm thick mineral fibre ceiling tiles shall be of dimension 595x595mm with humidity resistance 99% Thermal conductivity K = 0.052-0.057 w/mK colour white, fire performance UK Class 0/Class 1 (BS 476 pt-6&7) suitable for green building application (GRIHA Criteria 17 & 29 SWAGRIHA 12) with recycled content not less than 30 % and light reflectance not less than 85%. NRC of 0.55 to 0.6 duly fixed on GI Snap Grid Frame Work with Steel Screws complete all as specified and directed. Note: Snap grid ceiling frame shall be measured separately under appropriate item.

All as per item No. 40 above, but except material (Serviceable boards obtained from item No. 36 here in before) complete all as specified and as directed. Note: Snap grid ceiling frame shall be measured separately under appropriate item.

S&F 6mm thick HPSC cement fibre plain building boards, fixed to wall, including applying 2 mm thick wall putty in two coats finishing even and smooth and applying two coats of oil bound distmeper complete all as specified and directed.

M&L for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame, including various PVC angle/section all as per manufacture instruction and specifications including taking down carefully the existing electric point wiring and making it concealed by cutting grooves on brick walls as required at site for wall panelling complete all as specified and as directed.

M&L for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

S&F wall panelling with hollow 5 mm thick PVC panels of 10"/12" width and any height, single side pre-laminated with flat or fancy patterned on laminated side, fixing on walls with screws or with solvent cement as required on site including necessary corner angles, fillets etc as required at site complete all as specified and directed.

M&L for Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar, removal of debris outside AF land, cleaning of area to remove dust, loose particles, washing with water complete all as specified and directed.

M&L for providing Granite (of any type) Slab, 16-18mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement and admixture of pigment to match the shade of granite stone including edge moulding, grinding and polishing, laid over and including 20 mm thick screed bed in cement mortar (1:4), laid in any position / location complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deemed to be included in the quoted rate.

Dismantling Floor, Paver Tiles, Hearth or Wall Tiling, etc. including Cement Mortar Bedding (but not backing) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L Vitrified Coloured Tiles 9-10mm thick (Square/ Rectangular), Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc. Set in Neat Cement Slurry, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, laid with spacers to provide a uniform spacing of 3mm between the tiles complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deemed to be included in the quoted rate. Grouting shall be measured and paid separately.

M&L for grouting joints of ceramic floor tiles, area of each Tile not exc. 0.36 Square Metre in Floors, having 3mm joint width using epoxy grout mix of 0.70 Kg of organic coated filler of desired shade (0.10 Kg of hardener and 0.20 Kg of resin per Kg) including filling/grouting and finishing complete all as specified and directed. (NOTE: This item shall be executed only for Item No 49 here-in-before)

M&L Vitrified Coloured Tiles 9 to 10mm thick (Square/ Rectangular) Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Vertical Surface i.e. Dado, Skirting, etc., set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles, laid over and including 10mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deemed to be included in the quoted rate.

M&L for providing non-skid/matt finish Ceramic tiles, coloured, 7-8 mm thick (Square / rectangular), area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm in Flooring, set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the tiles laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.

-ditto- but ceramic tiles of size exc 0.11 Sqm but not exceeding 0.18 Sqm in skirting

M&L for Coloured Glazed Ceramic Tiles in vertical surface 450mm X 350mm X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the Tiles, laid over and including 10mm thick rendering as Screed or backing coat of wall tile in Cement Mortar 1:4, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.

M&L for providing outdoor type heavy duty ceramic Floor (Paver) Tiles, 400 x 400 x 10mm thick, having geometric patterns, Anti-skid type, Impact Resistant, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed. NOTE: Cost of Cement Screed Bed shall deemed to be included in the quoted rate.

Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and directed.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and directed.

S&F Chlorinated Polyethylene Chloride (CPVC) pipes 20 mm outside dia, SDR-11, having thermal stability for hot and cold water supply including all SDR-11 CPVC plain and brass threaded fittings (such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector etc) fixed / laying walls, ceilings or in floors etc. with suitable size MS clamp of spacing 1.00 mtr etc pipe line complete all as specified and directed.

-ditto- but with 25 mm outer dia size CPVC pipes

S&F in repairs CPVC Ball valve 20mm (outer dia), screwed both Ends for CPVC pipes, complete all as specified and directed.

S&F in repairs CPVC Ball valve 25mm (outer dia), screwed both Ends for CPVC pipes, complete all as specified and directed.

S&F in repair Vitreous China floor mounted one piece closet (Pedestal pattern), white including vitreous China valveless syphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, PVC soft close seat cover and connecting fittings complete all as specified and directed. (Make : CERA, Model: CHAMP / PARRYWARE, Model: Entice / HINDWARE, Model: FLORA / ASIAN PAINTS, Model: IMMERSE / ESSCO, Cat No: AIS-WHT-101851S220SPPSM )

S&F in repair PVC Flushing Cistern 10 Litre capacity White, Low Level, Valve less, Syphonic action type with Inlet, Ball Valve, Float and Handle, PVC Waste Pipe 32mm bore (dia) of suitable Length, a pair of Cast Iron Bracket/ Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm provided with 32mm dia Brass Chromium Plated Waste Fitting, PVC waste pipe, brackets incl making good disturbed Surfaces in Cement Mortar 1:3 and filling joints with whte cement complete all as specified and directed. (NOTE: Cost of CP waste coupling and PVC waste pipe is deemed to be included in the quoted rates)

S&F in repair PVC Connection Pipe 15mm size and 60 Cm in length with Adapter Nuts of PVC, complete all as specified and directed.

S&F in repair Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, Long Body with Capstan Head, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and directed.

S&F in repair Chromium plated brass Pillar tap, with aerator, fixed to wash hand basin, complete all as specified and directed.

S&F in repair 15mm bore chromium plated brass body single lever central hole basin mixer without popup waste system with 450mm long copper pipe and brass nut, complete all as specified and directed.

S&F in repair angle valve, 15 mm bore, cast copper alloy, chromium plated fancy type, concealed type with wall flange fixed to iron pipe complete all as specified and directed.

S&F in repair Chromium plated brass two way Angle valve, fancy type, concealed type with wall flange fixed to 15 mm bore of Iron pipe, complete all as specified and directed.

Demolition Cement Concrete (Reinforced) of slab, facia, Chajja, sunshade, chullah hoods and similar work (reinforcement cut as required to facilitate demolition) and removing debris, etc. to Outside MOD Land, complete all as specified and directed. NOTE : MS reinforcement obtained from demolition shall be measured under Sch of Credit

M&L for RCC 1:2:4 (type B1) using 20mm graded aggregate as counter/platform supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. NOTE : MS reinforcement shall be measured and paid separately.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed.

M&L for Mild steel TMT bars 10mm Dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm Dia complete all as specified and directed.

M&L Cleaning and removing all Scales and dirts from the Tank and mouths of circulating Pipes, etc. after draining out Water from the Tank of capacity exc. 250 Litre and not exc. 500 Litre, cleaning the Tank by scrubbing the deposits with Wire Brush, re-fixing Inlet and Outlet Pipes in the Same Position and writing Letters "CLEANED ON DD.MM.YYYY" (i.e. Date of Cleaning of Tank) not exc. 50mm in height, complete all as specified and as directed. NOTE:- The tank should be refixed after cleaning on the same day.

-ditto- but for tanks of capacity exc. 500 Litres and not exc. 1000 Litres

S&F in repair Rotational Moulded Polyethene Water Storage Tank, 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS, hoisted and fixed in Position incl providing new GI tank nipple complete all as specified and directed.

S&F in repair Rotational Moulded Polyethene Water Storage Tank, 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS, hoisted and fixed in Position incl providig new GI tank nipple complete all as specified and directed.

S&F in repairs Ball Valve 20mm Dia (minimum Weight 210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe, complete all as specified and directed.

S&F in repair Looking Mirror 5.0mm thick of size 600x600mm, fixed with Chromium Plated Brass Spacers 25mm to 30mm in size (One Each Corner) including rounding the edges of the Mirror complete all as specified and directed.

S&F in repair Brass Chromium Plated Tubular Towel Rail 20mm Dia, 60 Cm long with Brackets complete all as specified and directed.

S&F in repair stainless steel Grating Round 100mm Dia with waste hole jointing with Solvent Cement complete all as specified and directed.

S&F in repair Chromium Plated health faucet with 01 mtr long stainless steel tube including necessary fitting and fixtures complete all as specified and directed.

S&F in repair Jet Spray with Connection Pipe 15mm bore (Dia), Brass Chromium Plated and suitable for Wash Down Water Closet Pan (Pedestal Pattern) , complete all as specified and directed.

S&F in repair Vitreous China, white, half stall urinal flat back with grating and union for discharge pipe (excluding flush pipe and flushing cistern and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed. (NOTE: Quoted rate shall be deemed to include for the cost of waste coupling and waste pipe)

S&F in repair brass chromium plated Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed.

S&F in repair brass chromium plated Push Cock, suitable for urinals, duly fixed with flush pipe complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, laid on floor, trenches etc complete all as specified and directed.

S&F in repairs PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, laid on floors, trenches etc complete all as specified and directed.

S&F in repairs PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, fixed to Walls with PVC clips, complete all as specified and directed.

S&F in repair PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls with PVC Clips, complete all as specified and directed.

S&F in repair PVC (SWR) 75mm bore (dia), Bend any type, provided with Access Door, etc. and jointing with Solvent Cement , complete all as specified and directed.

S&F in repair PVC (SWR) 110mm bore (dia), Bend any type, provided with Access Door, etc. and jointing with Solvent Cement , complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal, with access door complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal, with access door complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) junction single (single T) equal or unequal, with access door complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) junction single (single T) equal or unequal, with access door complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl, 75 mm bore complete all as specified and directed.

S&F in repairs for waste coupling chromium plated for sink /wash basin, suitable for 32mm dia waste pipe complete all as specified and directed. (NOTE: This item shall only be measured for replacement in existing sinks, basins etc)

S&F in repair PVC Waste Pipe 32mm bore (dia), 90-100 cm length (as required at Site), complete all as specified and directed. (NOTE: This item shall only be measured for replacement in existing sinks, basins etc)

S&F in repair Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), White, Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device and complete all as specified and directed. NOTE: This item shall be measured for replacement of only seat cover on existing EWC.

S&F in repair Plastic seat & cover, white, soft close type, for water closet (of any description) incl chromium plated hinge complete all as specified and directed. NOTE: This item shall be measured for replacement of only seat cover on existing EWC.

S&F in repair faucet connector mixer connection pipe, 600mm long, inner PVC tube protected with high tensile braided stainless steel complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick in kitchen with plug washers, waste coupling, PVC waste pipe and fixing cantilever brackets connecting union to pipe, overall size of sink 914 mm x 460 mm and bowl size 405 mm x 354 mm x 203 mm complete complete all as specified and directed. (NOTE: Cost of CP waste coupling and PVC waste pipe is deemed to be included in the quoted rates)

Taking down damaged/unserviceable PVC Chowkat or Frame not exc. 1.50 Sqm Each with shutter (without taking off shutter from the frame) and removal from site complete all as specified and directed.

S&F Factory made solid PVC door frame (Chowkhat) of size 100 mm x 45mm made out of 5mm thick single side prelam PVC Sheet & edges painted to match with the prelam sheet, frame reinforced with MS square tube of size 40mm x 20mm of 19 gauge throughout the frame, fixed in opening as per specification & drg and as per manufacturer instructions complete all as specified and directed.

M&L for Factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with 2,4 or 6 raised panel design with 2 mm thick 3D wood grain moulded PVC Sheet polyurethane painted on the front face & 2 mm thick prelam PVC sheet on back face with particle board core suppling & fixing in the frame at site with SS hinges ss per specification & drawing and fixing in the Frame complete all as specified and directed. NOTE : SS Hinges will be Measured and Paid under appropriate Item.

S&F Butt hinges, 100mm long, stainless steel complete all as specified and directed.

S&F Aluminium alloy Handle 125mm long, cast type, anodised, complete all as specified and directed.

S&F Aluminium Barrel Tower Bolt 150 mm long, extruded section, complete all as specified and directed.

S&F Aluminium alloy, anodized, Sliding Door Bolt 200mm long with Hasp Staple (Bolt type) and Fixing Clips of Sheet cast or extruded section and fixing Bolts and Sliding Bolts of extruded section and fixing, complete all as specified and directed.

Taking down Wooden Chowkhat or Frame with Shutter (without taking off Shutter from the Frame), exc. 1.5 Square Metre but not exc. 4.0 Square Metre Each, complete all as specified and directed.

Taking down Chowkhat or Frame (any type) with Shutter (without taking off Shutter from the Frame), n.exc. 1.5 Square Metre Each, complete all as specified and directed.

Taking down and refixing of Shutters of any description in same opening n exc 1sq. m each complete all as specified and directed.

S&F Pressed Steel Frame of size 105x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates incl necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and directed. (NOTE: Cost of holdfast & hinge is deemed to be included in the quoted rate)

S&F Pressed Steel Frame of size 125x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates incl necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and directed. (NOTE: Cost of holdfast & hinge is deemed to be included in the quoted rate)

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) as in Filling Back side of Pressed Steel Frame, complete all as specified and as directed.

M&L for Flush Shutters of 35mm thick, ISI marked, solid core construction with block board core and plywood face panels, commercial type on both sides and fitted to Steel Frame, complete all as specified and directed.

M&L Panelled Shutter 35mm thick of Second Class Hardwood with Panels of 12mm thick Veneered Particle Board medium density wood with commercial face veneered both side and fitted to Chowkhat, having size of Rail and Stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

M&L Glazed and Skeleton Shutter 35mm thick of Second Class Hardwood prepared to receive Gauge/Glass (without Sash Bars) fixed with mitred beads supplied and fitted to Chowkhat and securing Glass, Gauge, etc. sizes of Members of Shutter as specified in SSR Part-I, Section-8, Clause 8.24(a), complete all as specified and directed. (NOTE: Mosquto proof netting shall be measured and paid seperately)

M&L preparing new or previously untreated Wood and Wood Based Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying two Coat of Synthetic Enamel Paint (First quality), over a coat of wood primer complete, including cleaning the surface, all as specified and directed.

S&F Aluminium Barrel Tower Bolt 200mm long (weight not less than 130 Gram), extruded section, complete all as specified and directed.

S&F Aluminium alloy Handle 150mm long (weight not less than 90 Gram), cast type, anodised, complete all as specified and directed.

S&F Aluminium alloy, anodized, Sliding Door Bolt 250mm long with Hasp Staple (Bolt type) and Fixing Clips of Sheet cast or extruded section and fixing Bolts and Sliding Bolts of extruded section and fixing, complete all as specified and directed.

S&F in repairs Floor Door Stopper 150mm in size, Aluminum alloy Body and Tongue with Hard Drawn Steel Spring (weight not less than 90 Gram), complete all as specified and directed.

S&F in repairs Door Spring of Mild Steel 150mm long, Ordinary Rat Tail type, Rod pattern Springs including Roller and Roller Plate welding with frame, etc., complete all as specified and directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, etc. and fixed complete all as specified and directed.

Taking down Steel Window, Ventilator Frame (without taking off Shutter from the Frame) of any description including Guard Bars/ Grill, not exc. 1.00 Square Metre Each, complete all as specified and directed.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed

Taking down Steel Window Frame (without taking off Shutter from the Frame) of any description including Guard Bars/ Grill, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each, complete all as specified and directed.

S&F Steel Window Box type using ERW ‘P’ Section comprising Double Frame for Gauged and Glazed Skeleton Shutters, having Outer Frame of Section 50x25mm and Inner Frame of Section 40x20mm, jointed internally with Mild Steel Flat Iron 40x3mm complete with Stainless Steel Tower Bolts, Hinges, Handles, Stops, Lugs, etc. including Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm, guard bars etc., complete all as specified and directed. NOTES:- (a) For the purpose of Measurement and Payment Double Shutters with Frame shall be considered as ONE UNIT. (b) Unit Rate quoted shall deem to be include all the Stainless Steel Builders & Hardware as required/directed at Site. (c) Quoted Unit Rate shall also deem to be include Mild Steel Guard Bars of 10mm Square Bar, spacing at 10 Cm centre to centre on both Vertical & Horizontal directions. (d) Sheet Glass shall be Measured and Paid for separately under appropriate Item.

S&F Plain Sheet Glass 4.0mm thick, Ordinary quality and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and directed.

S&F Frosted Sheet Glass 4.0mm thick, Ordinary Type and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and directed.

Taking down Aluminium Door Frame with Shutters of any description, area exc 1.5 Sqm and not exc. 4.0 Sqm Each, keeping aside for re-use after necessary repairs or removal from site (in case found unserviceable) complete all as specified and directed.

Taking down damaged/unserviceable Aluminium, window, ventilator etc, not exc. 1.50 Sqm Each with shutter (without taking off shutter from the frame) and removal from site complete all as specified and directed.

Taking down Aluminium Partitions, of any size or sections incl glass, particle/PVC boards etc and removal from site complete all as specified and directed.

S&F powder coated (medium thickness of powder coating 50 micron) anodised aluminium frame for door, windows, partitions and ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium doors shutters, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips rubber packing handle 2 Nos in each door, hinges, Mortise lock vertical type size 100 mm 4 levers of brass in each door, anodised aluminium snap beading screws etc as per manufactures instruction complete all as specified and directed. (NOTE:- Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle, Mortice Lock etc as described in item. Sheet glass shall be measured seperately)

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, anodised aluminum fittings such as suitable 150 mm long peg stays (01 No), hinges type B-21 100 mm long (02 Nos), suitable handle - 01No each shutter etc as per manufacturer's instruction complete all as specified and directed. (NOTE: Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle etc as described in item. Sheet glass shall be measured seperately)

S&F aluminium anodised decorative grills of size 75mm x 75mm having section width 6mm and 3mm thickness for aluminium windows incl all necessary jointing cleats, fixing clips, side channels, making holes for operation of handles etc complete all as specified and directed.

S&F Sheet Glass 5.50mm thick, Tinted (as approved by GE), fixed to Aluminium Doors complete all as specified and as directed.

S&F Sheet Glass 4.8 mm thick, Ordinary quality and glazing in Square exc 0.50 Sqm in Each Pane of aluminium Windows complete all as specified and directed.

S&F Sheet Glass 4.8mm thick, Frosted (as approved by GE), fixed to Aluminium ventilators complete all as specified and as directed.

Hacking out old broken Glass (any thickness, size, quality or description) from Wooden or Metal Frames, glazed with putty or fixed with beads, complete all as specified and directed.

S&F in repair Double Action Floor Spring Hydraulically Regulated made up of minimum 1.25mm thick Aluminium alloy Sheet Foundation Box, Main Body with Stainless Steel Cover, Governing Pivot made of Brass, Other Parts made of Mild Steel heavy duty complete all as specified and as directed.

S&F in repair Door Closer Aluminium (Die cast) body, hydraulically regulated, Designation No. 3, Universal type, suitable for Door Shutters of 851mm to 1000mm in width and of weight between 61.00 to 80.00 Kilogram complete all as specified and directed.

Taking down and Re-fixing of Aluminium Door Frame with Shutters (in same opening), of any description, after resecuring or easing and adjusting, etc. including re-fixing of glass sheet and replacement of necessary Jointing Cleats, Glazing Clips, Rubber Neoprene Packing, Screws, etc. and repairing of Locking Arrangement if any, complete all as specified and directed. NOTE : Cost of Materials required for smooth functioning of Shutter shall deem to be included in the Quoted Unit Rate. Locks and glass sheet, if required to be replaced shall be measured seperately under respective items.

-ditto- but for aluminium windows of any type or size

-ditto- but for aluminium ventilators of any size

S&F in repair Mild Steel Mortice Lock 100mm in size, 4-Lever, Vertical type, complete all as specified and directed.

S&F 5mm thick plain colour solid PVC sheets, cut to size and fixing in aluminium partitions, fixed with screws, solvent cement etc complete all as specified and directed.

S&F 12 mm thick pre-laminated particle boards, interior grade, laminated both sides, cut to size and fixed with screws to aluminium partions, doors etc complete all as specified and directed.

M&L preparing old Treated/Painted Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), upto 4 storey bldg height incl necessary scaffolding, safety gear etc complete all as specified and directed.

-ditto- but for one cost of synthetic enamel paint to old decorated steel surfaces for bldg height 5 to 8 storeys

M&L preparing old decorated/painted Wood and Wood Based Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (1st quality), upto 4 sorey bldg height including necessary scaffolding, safety gear etc complete all as specified and directed.

M&L preparation of surfaces and Writing Letters or Figures (Block Roman, Italic or Indian) on Buildings, not exc 30 cm High, alongwith providing background paint complete all as specified and as directed.

M&L for cleaning and preparation of old treated surfaces of wood or wood based surfaces, exc 10 cm in width or girth and applying one coat of varnishing complete all as specified and directed.

M&L for Forming Embankment including Raising or Lowering with a Mixture of Saw Dust and coarse Sand (mixed in a ratio of 1:3), Spreading in layers not exc. 30 Cm thick required size, made up to desired shape up to 3.00 Metre high from base on Small Arms Range (Firing Range) of Butt Wall including proper ramming and compaction of each layer before applying subsequent layers complete all as specified and as directed by Engineer-in-Charge. NOTES: 1) Saw dust & coarse sand shall be arranged by contractor from outside AF area under his own arrangement and cost of the same shall be deemed to be included in quoted rate.

All as per item No. 160 but exc. 3.0 m and n. exc 4.5 m height from base

All as per item No. 160 but exc. 4.5 m and n. exc 6.0 m height from base

All as per item No. 160 but exc. 6.0 m and n. exc 7.5 m height from base

All as per item No. 160 but exc. 7.5 m and n. exc 9.0 m height from base

All as per item No. 160 but exc. 9.0 m and n. exc 10.50 m height from base

M&L Repairing of broken/damaged portions of RCC Projection, Chajjas, Roofs Facia, Column, etc. upto any height adhering proper safety precaution and including necessary preparation i.e. scrapping, cutting, chiseling, removing all loose concrete and cleaning exposed reinforcement with wire brush, removing all dust & debris, cleaning with water and and applying one coat of cement slurry and filling the surfaces with min 25mm thick Cement Concrete 1:1½:3 (12.5mm graded stone aggregate) duly reinforced witth GI wire netting, surfaces finished to match with existing surfaces including providing a Coat of Chalk Whiting and finishing with Two Coats of Exterior Emulsion Paint over a coat of exterior cement primer with approved Tint as per manufacturer's instructions, complete all as specified and directed. NOTES : 1) Site for application is at various locations in patches with varying heights upto 12m. Contractor's quoted rate shall deemed to be inclusive of the ibid aspect. NO claim shall be entertained during currency of work. 2) Cost of Formwork/Prop, scaffolding, safety gear shall be deemed to be included in the Quoted Unit Rate. 3) Wire netting shall be paid seperately as "Supply Only"

Supply only wire netting of stainless steel wire, 1.4mm dia, with mesh size 12mm complete all as specified and directed.

Removing vegetation growth/shrubs (girth up to 30 CM), cutting in brick wall/concrete surface upto triple storey building carefully without damaging the existing soil, vent, water supply pipe and removing roots of plants completely and filling the gaps with PCC 1:2:4, Type B-0 finished with existing surface including all scaffolding ladder etc as required surface are n.exc. 0.36 Sqm each complete all as specified and directed.

shiv shanker enterprises (BID ID -3334622)

M/S D C M Enterprises (BID ID -3333735)

M/s Har Nandi Construction Company (BID ID -3343751)