repair renovation and white washing of office, laboratory and nine type house at RRS Balsamand

Amount

Earth work in excavation in foundations, trenches, etc .in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches ,stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres (HSR 6.6)

Removing door and windows (wooden and steel) together with the dismantling of walls. (a) doors (HSR 8.17(a)}

Removing door and windows (wooden and steel) together with the dismantling of walls. (a) windows (HSR 8.17(b)}

Scraping {HSR 8.32 (a) } (a) White wash and colour wash

Scraping {HSR 8.32(c)} (c) Cement plaster

Cement concrete 1:8:16 with stone aggregate 40 mm nominal size in foundation and plinth {HSR 10.28}

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (straight and curved) beams, girders, stairs, columns,(square or rectangular) battens and lintels etc., excluding steel reinforcement but including centring and shuttering, laid in position, complete in all respects. {HSR 10.86)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in footings, strips, foundations, beams, rafts, pedestals and approach slabs of bridges etc., excluding steel reinforcement but including centring and shuttering, laid in position, complete in all respects,(For work upto 1.5 metres below ground level). {HSR 10.90}

Extra over item Nos. 10.79 to 10.94 , if 1:1.5:3 mix is used, instead of 1:2:4 {HSR 10.95(a)}

12 mm thick cement plaster 1:4 on walls (HSR 15.5)

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10)

Cement pointing 1:2 deep variety on brick and tile work (HSR 15.60)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead , linseed oil, varnish and chalk mitti including finishing the surface to required finish complete (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping, etc. (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade (HSR 16.3)

Painting two coats with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.5)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces (HSR 16.25)

White washing three coats {HSR 16.48}

Providing two coats of exterior acrylic emulsion paint {HSR 16.79 (b)} (b) 1st quality

Proving and fixing 35 mm thick glazed door and windows shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc. ( non-coniferous timber other than teak confirming to I.S. specifications No. 1003 kiln seasoned), with vertical styles and rails, as specified in the statement no.1 ( attached in the end of this chapter), with glass panes of 4 mm thickness , tongued and grooved including the cost of iron hinges , screws, chocks/cleats, stops , etc., complete fixed in position excluding the cost of tower bolt and handles but including the labour for fixing the same (Based on 17.30 (a) + 17.24 (c)} (b) 35 mm thick ( 4 mm thick glass panes)

Wire gauze commercial hard wood such as hollock , champ, chikrassy , etc., ( Non –coniferous timber other than teak conforming to I.S. specification no. 1003 kiln seasoned) door and window shutters without springs housed in chowkats including chocks, iron hinges and screws, etc., complete fixed in position ( excluding the cost of tower bolt and handles but including the labour for fixing the same)- {HSR 17.31 (i)} (i)30 mm thick Note: Nothing shall be paid extra for additional vertical style (any size) if required by the Architect or by the Engineer-in-Charge)

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges :- {HSR 17.93(a-i)} (i) 25 mm thick

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges :-{HSR 17.93(a-iii)} (iii) 35 mm thick

Fe-500 D TMT steel bars for R.C.C., works, where not included in the complete rate of R.C.C. , including bending ,binding and placing in position complete (HSR 18.22)

Supplying and fixing glass panes including special metal sash putty of approved make(HSR 18.30(b)} (b) glass panes 4 mm thick, exceeding 40 sq dm areas

Providing and fixing 19 mm thick BWR Grade-II block board (ISI mark) shutters for cabinet including cost of iron hinges, screws etc., complete fixed in position but excluding cost of primer and paint(NS)

Shree Ram Building Solution Services

Rajender

Varun Kumar Contractor