CONSTRUCTION OF WATCH TOWERS AND REST ROOM ALONG WITH TOILETS ANNEXE AND PROVN OF ADDITIONAL ENTRY AND EXIT GATE AND WATER PROOFING TREATMENT IN INTERNAL WALL AND FLOOR OF SWT NO-7 AT AF STN RAJOKRI UNDER GE (AF) GURGAON

Amount

Surface dressing n.exc (not exceeding) 15 cm deep and getting out Hard/dense soil.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/Disintegrtated rock complete all as specified.

Excavating in trenches, n exc 1.5 m wide and exc 1.5 m in depth but n.exc 3.00 m; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/Disintegrtated rock complete all as specified.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete, sub base complete all as specified.

M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Columns, pillars, piers, posts and struts complete all as specified.

M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Slabs supported on walls,beams and columns in floors,roofs, complete all as specified.

M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Beams, cantilevers, bressummers, lintel over 1.5 span complete all as specified.

M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Chajjas complete all as specified.

Use of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter (rough finished surface) complete all as specified.

Use of formwork to sides of pillars,posts, struts, piers, columns and stanchions (square/rectangular/ polygonal) rough finished surface complete all as specified.

Use of formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work not exceeding 200 mm thick rough finished in flat surface complete all as specified.

Use of formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelvesincluding supports,overhangs,etc. also splays between floors in rough finished flat surfaces and etc complete all as specified.

Use of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide (rough finished surface) complete all as specified.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified.

All as per item No. 15 above but 5 mm dia & over upto & including 10 mm dia in stirrups,spacers and binders, complete all as specified.

M&L for brick work with sub class 'B' brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 etc complete all as specified.

M&L for half brick work with sub class 'B' old size brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:4 etc complete all as specified.

M&L for rendering 15 mm thick in cement mortar (1:6) on brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified.

M&L for 15 mm thick plastering in two layers (10+5) mm in cement mortar (1:4) on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets etc and finishing the surfaces even and fair (without using extra cement), top layer shall be with WPC as per manufacturer's instruction and complete all as specified. Note: WPC shall be measured and paid separately.

M&L rendering 10mm thick in cement mortar (1:3) as in ceilings finished even and smooth (without using extra cement) complete all as specified.

M&L for preparation of newly plastered or unplastered/undecorated surface of wall and applying two coats of oil bound distemper over one coat of primer complete all as specified.

M&L for preparation of newly plastered or unplastered/undecorated surface of ceiling and applying two coats of oil bound distemper over one coat of primer complete all as specified

M&L Preparing of new surface of wall and applying two coats of exterior emulsion paint over a coat primer on walls complete all as specified and directed by Engineer-in-charge. complete all as specified and as directed by Engineer-in-Charge .

Supply only intergral water proofing compound ISI Marked complete all as specified.

M&L for Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregates) as in sub base of flooing etc complete all as specified.

M&L for cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregates) 25 mm thick as in sub base of flooring/tiles etc complete all as specified.

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:4) for bedding of tiles complete all as specified.

M&L 10 mm thick rendering in cement mortar (1:3) on vertical surfaces for backing of tiles/granite etc complete all as specified.

Supply & Fixing of 18 mm thick Rajshri 100% solid WPC (Wood Polymer Composite) plain board (minimum density 650 Kg/Cum) fixed with screws, solvent cement/adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by Engr-in-Charge.

Supply & Fixing of 18 mm thick Rajshri 100% solid WPC (Wood Polymer Composite) of (minimum density 650 Kg/Cum) of one side Prelam/Rigidlam and other side balancing laminate colour to make kitchen cabinet shutter/drawer front shutters complete as per specifications and as directed by Engr-in-Charge.

Supply & Fixing of 6 mm thick Rajshri 100% solid WPC (Wood Polymer Composite) plain white board (minimum density 650 Kg/Cum) fixed with screws, solvent cement/adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per specifications and as directed by Engr-in-Charge.

Supply & Fixing of auto closing hinges openable at 0 degree for kitchen cabinet shutters complete as per specifications and as directed by Engr-in-Charge.

Supply & Fixing of stainless steel handles 100 mm size for kitchen cabinet/cupboard shutters.

M&L for Non - skid (joint free) coloured Vitrified Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for Non - skid (joint free) coloured Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for Glazed ceramic coloured tiles in vertical surface 450X 300X 6 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soft/loose soil etc complete all as specified.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified.

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified.

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified.

M&L Rendering 15 mm thick in CM 1:4 with water proofing compound @3% by wt of cement on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed .

M&L for water proofing treatment with APP (Atactic Polypropylene) modified polymeric prefabricated five layer membrane over roof consisting of cleaning of concrete or plaster surface of roof & parapet walls and applying evenly a bitumen primer confirming to IS 3488 @ 0.40 Kg per sqm laid using buten torch and sealing all joints of APP modified polymeric water proofing membrane minimum weight 3.6 kg/sqm reinforced with non woven polyester fabric (weight not less than 160 grams per sqm) unrolled and bonded to substrata with logitudinal and end laps 100 mm and 150 mm respectively as per manufacturer's instructions incl two coats of water proofing paint with aluminium finish on top complete all as specified.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F factory made 35mm thick 2nd class hardwood glazed and skelton door shutters, open rebated and prepared to receive glass, gauze, (without sash bars) edges for framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-1 section 8 clause 8.24 (a) fitted to chowkats complete all as specified.

S&F solid PVC door frame of size 50mm X47mm made out of 5mm single side prealm PVC sheet & edges painted to match the prealm laminated shhet , reinforced with MS square tube supplying and fixing in opening as per specification and drawing.

S&F factory made PVC shelter panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling in both sides of Prelam laminated sheet to be fitted in MS frame welded/ sealed to the stiles and rails (feathered at edge) with suitable PVC sheet beading and joined together with solvent cement , supplying and fixing in the frame at site as per specification & drawing as specified.

S&F 100 mm Butt hinges, Stainless steel and fixed complete all as specified.

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified.

S&F 150 mm size extruded aluminium alloy handles fabricated type anodised and fixed.

S & F 300 mm long mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed by engineer incharge

S&F 250 mm long aluminium alloy anodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast sections or cast aluminium alloy complete all as specified.

S&F window or ventilators section of frame 72x55mm fixed to wall or concrete surface with rowl plugs made of galvanised steel powder coated and section of shutter 47x20mm mulion section 72x50mm (Based steel as per IS 513 "D" quality galanised as per IS 277 with zinc of 120 gms/sqm) glazed or gauged and wire gauge shutter prepare to receive wire mesh to the shutter (Double door shutter) with total coated thickness of 0.6mm including grills/guard bars made of square bars powder coated fixed to window frame with screws including necessary fittings and all builders hardware such as handles, tower bolts and stays etc complete all as specified and as directed. Make : NCL type-4000 Series (Note : Glass and wiremesh shall be measured and paid separately under respective items)

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified.

S&F sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beads complete all as specified.

S&F GI tubes medium grade with all fitting and fixed complete to walls, ceilings or laid in floors 15mm bore complete all as specified and directed.

S&F tubes 20 mm bore dia, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floos, complete all as specified and directed.

M & L Vitreous china wash down water closet pan, pedestal pattern (EWC) white, including seat cover , fixing bolts connection to trap & to flush pipe fixed in repairs complete all as directed by the Engineer-in-charge.

S&F 500 ltrs rotational moulded polyethylene water storage tanks (cylindrical verical with closed top) hoisted and fixed in position including ball valve of 20 mm dia complete all as specifed and directed.

S & F for Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, Bore dia of pipe in 20 mm, etc complete all as specifed and directed.

S&F for Vitreous China Urinal, Half stall type, white including waste pipe and water splinder, etc complete all as specifed and directed.

S&F vitreous china pedestal wash hand basin (flat back) of size 550x400mm including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector, including cutting for and pinning in ends of brackets complete all as specified.

Shelf of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleates.

S&F grating doom 100mm dia size with PTMT complete all as specified and directed.

S&F PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action type with inlet ball valve and float, handle with & including bracket and PVC flush pipe 32 mm bore complete all as specified.

S&F bib taps, long body, brass, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified.

Supply and fixing for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified and directed by Engr-in-Charge.

S&F fancy type Angle stop cock with flange, 15 mm nominal bore, brass, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified.

S&F Centre hole basin mixture with hot or cold mounted tap of 15mm bore dia, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts fancy type screwed for iron pipe, fixed as in repairs, complete all as directed by EIC.

S&F PVC connection 450 mm long suitable for 15 mm GI pipe with two brass nuts & rubber washers complete all as specified.

S&F tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed

S&F PVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified.

S&F 110mm dia PVC (SWR) pipe and single socketed in any length with rubber ring joint fixed to wall.complete all as specified

S&F PVC (SWR) bends any radius 110mm bore. Complete all as specified

S&F PVC (SWR) junction single, (single T) equal or unequal 110mm bore complete all as specified.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 75mm bore.

S&F PVC (SWR) bends any radius 75mm bore.

S&F PVC (SWR) junction single, (single T) equal or unequal 75 mm bore complete all as specified.

M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over screed bed or bedding layer of mortar 15 mm thick in cement mortar (1 : 4) laid complete all as specified.

M & L for Machine cut kota stone slab in riser of steps, skirting, dado and pillar laid over cement , 20-25 mm thick including rubbing and polishing over 10 mm thick rendering in cement mortar (1:4) on vertical surfaces for backing of tiles complete all as specified.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/disintegrated rock.Complete all as specified

M&L 100 mm thick PCC 1:4:8 tybe D-2 using 40mm stone aggregate as in subbase.Complete all as specified

M&L for providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved , design & pattern as in footpath , parks , lawns,drive ways or light traffic parking etc. of required strength , thickness & size/shape, made by table vibratory method using PU mould , laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand , compacting and proper embedding/laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator,filling joints with sand andcutting of paver block as per required size and pattern,finishing and sweeping extra sand. Complete all as specified

S&F rolled mild steel in framed work as in doors or steel gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing conforming to Fe- 290.Gde-E-165 complete all as specified.

Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc

M&L prepration of new Steel surfaces of any description, not otherwise described, over 10cm width or girth & applying two coats of synthetic enamel paint over coat of red oxide primer complete all as specified

M&L for reinforced concrete pipes 150 mm dia, class NP-2, laid and jointed complete with collars complete all as specified.

M&L cement concrete 1:3:6 type C-2 for 150 mm dia in bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested etc complete all as specified.

S&F SFRC manhole cover 75mm thick factory made with plain surface as per requirement including 75 X1.5 mm flat iron frame all around the cover complete all as specified.

Construction of RCC septic tank of 10 user's including on site designed to carry sewage and excavation in any type of soil, foundation in PCC 1:4:8, walls of soild brick in CM 1:4, RCC baffle wall, RCC cover slab in M-25 including SFRC manhole cover, MS rungs, Vent shaft, connection etc. complete all as per specified and shown on drg No.CEJZ/STD-263/90 Sheet No. 1/9 to 9/9.

Construction of Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of Brick masonry in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/ DWC complete filled with brick bats of size 1.2 mtr dia and 3.00 mtr in effective depth complete all as specified and shown on drg No.CEJZ/STD-301/90 Sheet No. 1/4 to 4/4.

Excavation over areas n.exc 1.50 m deep and getting out in hard/dense soil complete all as specified and as directed.

M&L Reinforced cement concrete Nominal mix Type B1 1:2:4 (using 20 mm graded stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and as directed.

M&L for joint free coloured glass mosaic tiles 9-10 mm thick (Square/rectangular), of with adhesive and filled gap with grounting materials, polished, etc area of each tile not exceeding 0.36 sqm, fixed in floor/wall etc over 15 mm thick in cement mortar (1:4) for bedding of tiles set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified and as directed.

M&L for 10 mm thick natural stone/Texture finish tiles (Square/rectangular), for back side wall cladding with cement over 15 mm thick in cement mortar (1:4) for bedding of tiles set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified and as directed.

M&L for Granite stone slab flooring 20 mm thick any colour/shade machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over 15 mm thick in cement mortar (1:4) for bedding of tiles including grinding and polishing, rounding edges as required to be fixed gate pillar, door, windows cladding/flooring and openings complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) Soil, waste and rain water pipes single socketed in any length with rubber ring joints fixed to walls/floors complete all as specified & directed.

S & F 40 mm bore PVC (SWR) Soil, waste and rain water pipes single socketed in any length with rubber ring joints fixed to walls/floors complete all as specified & directed.

S & F 40 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

S & F for SS Cascade waterfall (wall mounted waterfall shower) and pools water desent blades of 600 mm Chilly fancy type etc complete all as specified and directed .

S & F for SS fountain Bubbler Nozzle of pressure (Kpa) 70-350 of Bubble Tree water Shape etc complete all as specified and directed .

Taking down cement plaster or cement lime plaster on brick,concrete or stone surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified

Demolition of cement concrete (unreinforced) including cast-in-situ terrazzo in ground floors and pavings not exc 15cm thickness (below or above ground level).all as specified and directed.

M & L 75 mm thick, plain cement concrete 1:2:4, type B1, using 20 mm graded crushed stone aggregates, as in sub base of flooring and finishing cement concrete surface finished even and smooth without using extra cement, complete all as specified and as directed.

Grouting by wrapping all pipes insert with a two way adhesion tape of make Dr. Fixit Bathseal tape/Dr. Fixit Bonding agent and grounting the gaps space with non-shrink grout Dr. Fixit Pidigrout 10M or PMM prepared by polymer modified motar with Dr. Fixit Pidicrete URP in the ratio of 1:3 by adding polymer 10% by weight of the cement & M&L for two coats of CFTRI approved waterproof coating with high performance two component pre-packed cementitious waterproofing Dr. Fixit Fastflex, with a mix ratio of (liquid : Powder), parts by wt 1:1.4 @ 0.42-0.50 Sqm/Kg to achieve 1 mm DFTover the floor surface & wall surface upto full height as per the manufracture;s instructions . All the coats to be applied in right angle to each other an interval of 4-6 Hrs including proper surface preparation as per manufracture's specification, cleaning, removal of loose concrete and filling cracks with polymer modified motar using SBR Latex Dr. Fixit Pidicrete URP. Provide and lay 45 GSM glass fibre mesh over the angle fillet when the first coat in still wet. Allow the coating to air cure for 5 days before conducting water ponding test for 24 hrs.

Supply and lay GI tubes medium grade galvanised with all fitting and fixed complete to walls and ceiling or laid in floors of size 25 mm bore all as specified and as directed

.Supply,fixing and testing Gun metal gate valve 25mm ,screwed body ends and cast iron hand wheel conforming to IS 778-1984 ans ISI marked complete all as specified and directed.

M&L for Drilling holes for bolts, pipes, etc.n. exc 25mm dia including earth work, excv etc complete all as specified and as directed.

Supply, laying, jointing and testing XLPE LT Cable insulated, PVC outer sheathed, galvanised steel strips armoured, heavy duty power cable with aluminium conductor suitable for rated voltage of 1100 Volts grade earthed system and conforming to IS : 7098 of 1995 and of size 4.0 core x 25Sqmm and laid in trenches/ducts/pipe or on poles complete all as specified and directed.

Supply ,installation ,testing and commissioning feeder pillar board of size 60 cm X 45 cm X 30 cm Kiosk type ,LT(415 Volts, 50 Hz , 3-phase, 4 wire supply) floor mounted , factory assembled, outdoor type weather and vermin proof (Protection Class IP-54) made out of 40m x 40mm x 6mm angle iron frame and 3.15 mm thick MS Sheet CRCA sheet with front hinged opening, rubber lining, locking arrangement powder coated externally and internally bus Bar chamber comprising 4 Nos aluminium strip bus bars air insulated and PVC sheathed capacity 400 Amps with colour coding including excavation and earth works and including grouting with PCC foundation complete all as specified and as directed.

M&L for earthing complete with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to GI srtip 25x4 mm as earth lead by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge mesh, 80 mm thick RCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision of 20 mm dia medium grade pipe for watering and light grade 20 mm dia for protection and including all excavation and earth work & connecting the earthing to an earthing test point complete all as specified & directed . Note:- GI strip upto 7.5 mtr deemed to be included in the quoted rates.

Supply only the following items of DG Set of various capacity complete all as specified and as directed by Engr-in-charge :-

One light point controlled by one,one way switch.

One ceiling fan/exhaust fan controlled by one way switch.

Socket 3 pin 5 Amps on the same board, complete all as specified.

Socket 3 pin 5 Amps on independent board , complete all as specified and directed.

M&L for point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 2.5 sqmm drawn through in and including concealed PVC conduit size of not less than 20mm concecled in wall / surface including provn of pressed steel terminal box of suitable size with 3mm thick plastic laminated sheet cover / modular white cover plate with frame as required module & modular metal flush box as required module for mounting switch, socket and fan regulator along with earth wire of PVC insulated, unseathed, 1100 V grade cable multi stranded copper conductor of size 2.5 sqmm and making good, disturb surface as it is, all as specified and directed for the following. Note :- Colour coding of cable should be Phase- Red, Neutral- Black and Earth- Green

M&L in replacement for sub main wiring with two single core 4 Sqmm stranded copper conductor PVC insulated and unsheathed cable ISI marked in 25 mm dia, medium grade, PVC conduit concealed in wall for sub main connection including 4 Sqmm PVC insulated unsheathed copper conductor ISI marked as earth wire complete all as specified and directed by Engr-in-charge.

S&F for socket outlet 5 Amps, 5 pin flush type, 240 volts. with polycarbonate body. complete all as specified and directed..

S&F for socket out let, 6 pin 5/15 Amps multi purpose 2 in 1 flush type, 230 volts with polycarbonate body.complete all as specified and directed.

S&F for switch piano flush type single pole one way 5 Amps 240 volts with polycarbonate body complete all as specified and directed..

S&F for switch piano flush type single pole two way 15 Amps 240 volts with polycarbonate body complete all as specified and directed..

S&F For ceiling fan regulator stepped electronic type 300 watt rating, 230 volts with polycarbonate body all as directed.

M&L for ceiling rose 3phase/PVC polycarbonate isolated body complete all as specified and directed

Supply and fixing LED lights fitting 1x 22W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers Complete all as specified and directed

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFMwith service value 6.00 BEE. Five starrated with brushless direct current motor (BLDC) complete all as specified and as directed.

S&F electric water heater storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 Ltrs BEE 5 star rated complete with all accessories such as safety valve thermostate NRV connection pipes complete all as specified and as directed.

S&F sheet metal enclosure single pole and neutral two pin and earth plug and socket complete with one double pole MCB SP 20 Amps for geyser complete all as specified and as directed.Make- Havells/Legrand or equvalant.

S&F in replaceent of MCB DB sheet enclosure single pole and neutral 240V with 200 Amp suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated Acrylic double door complete confirming to IP 43 with enclosure blank plates for unused way suitable for 8 way complete all as specified and directed : Havells or equvalant in Hager/ Legrand

S&F MCB, single pole & neutral, 240 Volts ( 40-63) Amps,10KA, 'C' series complete all as specified and directed.

S&F MCB, single pole, 240 Volts (05 to 32) Amps,10KA, 'C' series complete all as specified and directed.

S&F LED bldg light fitting 35/36 Watt, having uniformty ratio 0.25 , high pressure die cast aluminium housing , heat resistant toughened glass frame , IP-65 protection complete with lamp & connected items and connection with suitable cable from celing rose to light fitting and fixing on GI pipe bracket made out of suitable dia GI pipe medium grade 1.2 m long bend to shape and fixed on wall with flat iron clamps nut, bolts washers etc specified and directed

M&L for earthing complete with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to GI wire 4 mm Dia as earth lead by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge mesh, 80 mm thick RCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision 20 mm dia medium grade pipe and watering pipe shall be 20mm bore medium grade, and including all excavation and earth work & connecting the earthing to an earthing test point complete all as specified & directed . NOTE: (i) The concrete pit shall be PCC 1:3:6 type C-140 mm thick pre cast cover slab of RCC(1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with 8 mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cost iron cover shown in the electrical plate No.3 of MES SSR Part -1 (ii) item includes the cost of 7.5 m GI pipe for protection of GI wire. (iii) PCC pits extra cost of addtional length of watering pipe,bends elbows etc.shall be deemed to be included in the quioted rate. (iv) Item includes the cost of 7.5 mtr length Galvised wire 4 mm dia.

akhil enterprises (BID ID -3441301)

M/S GEETANJALI ENTERPRISES (BID ID -3447793)

M/S RK Builders (BID ID -3440783)

innovision limited (BID ID -3439300)