Renovation of Conference, Meeting Room and Open Duct Area in CIF Building at IITG Campus

Amount

CIVIL:

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessarydeduction for scaffolding in the existing item to be done.

Cutting Existing crack in a Vshape groove cleaning the same with proper means application of Sika214 non-shrinkage powder over the entire crack area and let dry. Finally plaster the surface ever required.

Damp proofing in walls

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead..

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge

15 mm thick plastering with cement mortar 1:4 (1 cement: 4 fine aggregate) over the water proofing treatment area admixed with Acrylic Polymer@ 10% by weight of cement.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre,of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour

Finishing walls with Acrylic Smooth exterior paint of required shade

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.

2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supply and Installation of channeled woodworks perforated panels with required size, made of moisture resistant fibre board with minimum density of 500-700 NRC upto.75 in approved colour shade with necessary with necessary GI framing. Make-UNIDUS, Anatoune, CALSE, FIBRECRET or Equivalent

Providing and fixing of Natural creation Arbor Art classic/Antique 2 mm thick of Armstrong PVC floor with approved adhesive and joints to be filled up by heat torching.

Provodong of 100mm Vertical Blinds as per directions of Engineer-in-Charge

Fiting & Fixing of Vertical Blinds

ELECTRICAL:

Part - A

Wiring for circuit /submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

i) 2x1.5 sqmm + 1x1.5 sqmm earth wire.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required

3 module

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

Part - B

Supply of 20W LED Light TMC set. (Make- Phillips/ Havells/CG/Bajaj)

NARAYAN DEKA (BID ID -3144399)

Madhav Borah (BID ID -3144440)

ANUP CHAKRABORTY (BID ID -3144429)

DHIRAJ THAKURIA (BID ID -3144359)

MAHALAXMI ASSOCIATE (BID ID -3144133)