ADDN/ALTN TO CERTAIN PARKING SHED P-82, P-104, P105, P106 AND P-107 AT THANE, 10000 LTR WATER TANK MAHUL, MI ROOM P-70 AT INS TANAJI, PROVN OF DEF WATER COOLERS, LED LIGHTS, HIGH MAST LIGHT, SPL REP OF BER CEILING FANS, THANE UNDER GE (NW) MANKHURD

Amount

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed. Note: No mechanical method including brakers may be adopted at site for taking down of old plaster.

M&L for 5 mm thick polymer modified ready mix cement based plaster on surfaces of ceiling including finishing the surface even & smooth without using extra cement, complete all as specified and as directed. Make : Easy plast from M/s wall plast or chemplast or Readiplast from ultratech. Note: The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with the ready mix plaster and nothing extra shall be payable on this account.

M&L for 8 mm thick polymer modified ready mix cement based plaster on surfaces of ceiling including scraping down existing plaster and finishing the surface even & smooth without using extra cement, includign scaffolding as required complete all as specified and as directed. Make : Easy plast from M/s wall plast or chemplast or Readiplast from ultratech. Note: After taking down old plaster if the replaster to be done of thickness over and above 8mm to maintain line and level of plastered surface are deemed to be included in the qouted rate.

M&L for 10 mm thick polymer modified ready mix cement based plaster on the wall surfaces including scaffolding as required finishing surfaces even and smooth complete all as specified and directed Make: Easy Plast from M/s wall plast or chemplast or readyplast from Ultratech” Note: After taking down old plaster if the replaster to be done of thickness over and above 10mm to maintain line and level of plastered surface are deemed to be included in the qouted rate.

M&L for 12 mm thick polymer modified ready mix cement based plaster on the wall surfaces mixed with liquid water proofing cpmpound in the protection as per manufactiur's instructions and including finishing surfaces of the top layers even and smooth, complete all as specified and diected Make: Easy Plast from M/s wall plast or chemplast or readyplast from Ultratech Note: The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with ready mix plaster and nothing extra shall be payable on this account. (ii) WPC shall be paid for separately

M&L for 20mm thick polymer modified ready mix cement based plaster in two layers (12 + 8 mm) on the wall surfaces, top layer of 8 mm mixed with liquid water proofing compound in the proportion as per manufacturer’s instructions and including finishing the surfaces of the top layer even and smooth, including scaffolding as required complete all as specified and directed, Make : Easy plast from M/s wall plast or chemplast or Readiplast from ultratech. Notes : (i) After taking down old plaster if the replaster to be done of thickness over and above 20mm to maintain line and level of plastered surface are deemed to be included in the qouted rate. (ii) WPC shall be paid for separately.

Chipping, removing carefully loose/damaged concrete incl plastering (total thickness upto 60mm ) from RCC surfaces of columns, beams,Chajas, soffits of slabs etc by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land, complete all as specified and directed. Note: Hard concrete shall not be removed by force. (upto 15.0m height of bldg or 5 storey bldg)

M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hour between the coats, complete all as specified and directed. [Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers) will be measured.]

M&L for Anticorrosive Treatment to Reinforcement using IPNET-RB of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces complete all as specified and directed. Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers) will be measured.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit, upto 20mm thickness while the bonding agent is still tacking, including levelling, profiling etc, complete all as specified and directed. (upto 12.0m height of bldg or 5 storey bldg)

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit while the bonding agent is still tacking, exceeding 20mm thickness and not exceeding 40mm thickness in two layers, each layer not exceeding 20mm, including levelling, profiling etc, complete all as specified and directed. (upto 12.0m height of bldg or 5 storey bldg)

M & L for building up the profile of structural members by using polymer modified mortar from M/s Krishna conchem (Molith PMM) or polymer mortar HB of Dr Fixit while the bonding agent is still tacking, exceeding 40 mm thick and not exceeding 60mm thickness in three layers, each layer not exceeding 20mm, including levelling, profiling etc., complete all as specified and directed. (upto 12.0m height of bldg or 5 storey bldg)

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application complete all as specified and directed.

M&L for casting & repairing of excessively damaged distressed RCC members (exceeding 60mm in thickness) with prebatched, prepacked, single component ready to use microconcrete from Fosroc (Renderoc RG) or equivalent of Dr. Fixit as approved by GE, at any level/ height and at any lead or lift as directed including prefabricated water tight formwork, centering, scaffolding, also including mixing , laying, levelling, finishing, curing etc as per manufacturer's specifications and all other relevant works, complete all as specified and directed. (Note : Reinforcement only shall be measured and paid separately).

M&L cement plaster (1:3) with 10 mm thick to be finished smooth without using extra cement mixed with WPC @ 2% by weight of cement, , complete all as specified and directed. Note : WPC shall be measured and paid separately as supply only.

Supply only liquid water proofing compound, complete all as per manufecturer instruction and all as specified and directed

M&L for PCC (1:2:4) type B-0, using 12.5mm graded stone aggregate as in levelling course over RCC roof/ terrace surfaces to achieve required slope, benching etc including making rounded or chamfered on edges mixed with WPC as per manufacturer's instructions, including demolition of old PCC of any description, complete all as specified and directed. Note : WPC shall be measured and paid separately as "supply only".

M&L PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in hold fast, bed plate etc including necessary form work complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 Using 20 mm graded stone aggregate for walls or retaining walls,any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) as specified.

Taking down complete existing APP membrane and M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (d) Over the membrane provide a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/Sqm as prescibed by manufacturer.

Dismantling floor, hearth or wall tiling including cement mortar, hedding removing serviceable tiles to store and rubbish off the premises all as specified and directed .

M&L plain cement concrete 1:2:4 type C2(40mm graded aggregate ) as in filling under post hole etc complete all as specified and directed

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240.

S & F rolled mild steel in roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing(Beam,tee, angle, channel or flat sections)incl distance pieces, cleats, etc conforming to grade Fe-410W-(Gde E-250 Quality A).

S & F MS bands, straps, supports or stays for rainwater, ventilating pipes, including bolts if reqd, hooks(stay), hook and pintle hinges, large hasp and staples, clamps, hold fasts, wall ties, plain angle cleats for securing purlins to wood trusses or rafters and similar small articles confirming to Fe-290 Gde E-165.

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling Asbestos cement (corrugated, semi corrugated, etc sheets in roof coverings complete all as specified and directed.

S & F Pre painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of colour having tensile stength of 550Mpa as in roof coverings/cladding to wall, fixed with self tapping screws as specified.

Preparation of new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

S & F PVC (SWR) pipe 110 mm bore single in any type with rubber ring joint laid in wall/trenches /floor.

S & F PVC (SWR) bend any radious 110 mm bore.

S & F for 110 mm dia PVC rain water pipes complete all as specified and directed

S & F for 110mm dia PVC bends complete all as specified and directed

S &F PVC (SWR) junction single(single T), 110 mm bore, equal or unequal

M&L for 150 mm Internal diameter of pipe Sail-glazed stoneware drain pipes laid in trenches and jointed as specified

S&F 150 mm Bends and taper bends as specified

S&F 150 mm single Y junction as specified

Formwork to sides of pillars,posts, struts, piers, columns and stanchions complete all as spd and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement.

M & L for hard core of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 10 cm thick watered and rammed to a true surface complete all as specified.

M & Laying cement concrete for foundation fillings and mass conctere type D2 1:4:8 using 40 mm graded aggregate complete all as specified and directed.

M&L for prepration of new and old plastered surfaces of wall applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as per manufacturer instruction and all as specified and directed.

M&L for prepration of newly plaster surface of wall two coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour Incl 2 mm plaster of paris putty complete, as per manufacturer's specification.

M&L for prepration of newly plaster surface of ceiling two coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour Incl 2 mm plaster of paris putty complete, as per manufacturer's specification.

M&L for prepration of old plaster surface of ceiling complete removal of existing treatment and two coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour Incl 2 mm plaster of paris putty complete, as per manufacturer's specification.

M&L for prepration of old plaster surface of wall complete removal of existing treatment and two coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour Incl 2 mm plaster of paris putty complete, as per manufacturer's specification.

M&L for prepration of newly plaster surface of wall applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as per manufacturer instruction and all as specified and directed.

M&L for prepration of old plaster surface of wall washing rubbing down and stopping of distempered and painted surfaces and painted surface applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as per manufacturer instruction and all as specified and directed.

M & L for preparation of old painted wood surfaces of any description, not otherwise described over 10cm width or girth applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description, not otherwise described over 10cm width or girth applying two coat of synthetic enamel paint over one coat of red oxide, zinc chrome primer complete all as specified and directed.

M&L for RCC work 1:2:4 nominal mix (20 mm graded aggregate) for cooking platform Chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings Demolition of cement concrete ,(reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

M&L for reinforced cement concrete nominal mix M-20 (using 20 mm graded stone aggregate) for foundations, including rafts, footings, foundation beams, plinth beams, bases for column etc and mass concrete, complete all as specified and directed. (Note - Reinforcement and form work will be measured and paid separately).

Demolition of cement concrete (un-reinforced) in ground floors and pavings any thickness (below or above ground level) all as directed.

M&L for providing 75mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement, complete all as specified and directed.

S & F 100 mm thick cement concrete type B-1 1:2:4 ( 20mm Graded agg) as in floor all as spd.

M & L for Durastone Heavy Duty Vitrified tiles (300 mm x300 mm) 10-12 mm thick in floor set and jointed with neat cement slurry and pointed in coloured cement to match over and including screen bed or bedding layer of mortar 20 mm in cement 1:6 complete all as specified and directed

M & L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished area of each tiles n.exceeding 0.36 sqm, in floors etc. set and jointer in neat cement slurry and pointed in white or coloured cement to match the shade incl 15mm thick CM 1:6 screed bed for laying floor finishes incl removal of cement mortar bedding (but not backing) removing serveable tiles store & rubbish complete all as specified and as directed.

All as per items No 56 above but in skirting or in dado including 10 mm thick rendering CM 1:4 incl removal of cement mortar bedding (but not backing) removing serveable tiles store & rubbish complete all as specified and as directed.

M&L non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors over screed bed or bedding layer of morar 15 mm in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface incl dismantlling floor herth or wall tiling incl removal of cement mortar bedding (but not backing) removing serveable tiles store & rubbish complete all as specified and as directed.

M&L for Glazed ceramic colour tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchincluding 10 mm thick rendering CM 1:4 incl dismantlling floor herth or wall tiling incl removal of cement mortar bedding (but not backing) removing serveable tiles store & rubbish complete all as specified and as directed.

M&L for Providing 300x300x 7-8 mm thick non skid Digital dark coloured Tiles as in floors over screed bed or bedding layer of morar 20 mm in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface incl dismantlling floor herth or wall tiling incl removal of cement mortar bedding (but not backing) removing serveable tiles store & rubbish complete all as specified and as directed.

M&L Digital coloured wall tiling of 300x600x 7-8 mm thick wall tiling on vertical surfaces, skirting/dados etc. over screed bed or bedding layer of mortar 15 mm in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white / coloured cement to match the surface incl dismantlling floor herth or wall tiling incl removal of cement mortar bedding (but not backing) removing serveable tiles store & rubbish complete all as specified and as directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. over screed bed or bedding layer of morar 15 mm in cement mortar 1:4set and jointed in neat cement slurry and pointed in white or coloured cement to match incl removal of cement mortar bedding (but not backing) removing serveable tiles store & rubbish complete all as specified and as directed.

M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as in cills, jambs etc, including moulding/rounding to edges of the slab and also including 15mm thick screed bed in CM 1:4, incl removal of cement mortar bedding (but not backing) removing serveable tiles store & rubbish complete all as specified and as directed.

Supplying and laying 16 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings (including provision of special fittings i.e brass elbow brass tee ,male brass thread adoptor ,female brass thread adaptor etc required for bib tap,stop cock with CPVC pipe concealed in walls/ceiling or laying in floors etc also including cutting chases grooves and making good the same in CM 1:3 after fixing of pipes /fittings including taking up or down steel water tubing and connections complete all as specified and as directed complete.complete all as specified and as directed

S&F cast iron Nahani trap 100mm dia out let including grating connecting jointing to waste pipe with lead jointing and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

S&F PVC connections 15mm size with PTMT nuts of length 600mm.

S&F towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms).

S&F in repairs 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and as directed .

S&F in repairs 15 mm dia bib taps,fancy type chromium plated cast copper alloy with crutch , screwed down screwed for iron or for brass ferrule complete all as specfied and drecetd.

S&F in repairs 15 mm dia bib taps two way cock , cast copper alloy with crutch , screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated Make Jaquar or equivalent make as approved complete all as specfied and drecetd

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs 15 mm Bore dia Pillar taps fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specfied and drecetd.

S&F in repairs 15 mm bore stop cock cast copper alloy with crutch or for brass chromium plated with fancy shank and cup(concealed type) complete all as specfied and drecetd.

S&F in repairs Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed.

S&F vitreous china, table top wash hand basin oval shape size( 420x420mm x135 mm) cat No : ARS-WHT-0538 Make of JAQUAR fixed on granite counter top slab including brass chromium plated full threaded waste coupling with grating 32mm dia pvc waste pipe complete all as specified and directed. (Note: Granite slab, RCC plat form, brick wall support etc shall be measured and paid separately)

S & F in repairs Vitreous China Wash hand basin white, flat back, size 550x400 mm size (flat back or angle back type)excluding taps, waste, chain and plug and procelaim stopper but including cutting for and pinning ends of brackets or erecting stand.incl taking down pillar tap complete all as specified and directed

S & F Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S&F in repairs for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) plete including provision of lime concrete bedding etc complete all as specified and as directed

S & F for Vitreous china wash down water closet pan “Pedestal Pattern” white, with seat coverwhite closed pattern with flat bottom and cover mild steel chromium plated or aluminium anodized hinging device and joints etc and connection to drain, flushing pipe, anti-syphonage pipe and fixing arrangements with fixing bolts etc including making good the disturbed portion of floor in cement concrete 1:2:4 type B-0, as in repairs, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame/aluminium frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

Supply only stainless steel wire cloth 0.36mm mm nominal dial of wire and average width or aperature 1.40mm for fixing to wooden door/ window shutters in any position with new beads/ steel section as required for securing including dismantling of old jalli and painting to match with existing complete all as specified and as directed.

supply and fixing Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane 4 mm thick quality fixing to wooden door/aluminium window shutters in any position with new beads/ steel section as required for securing including dismantling of old jalli and painting to match with existing complete all as specified and as directed.

S & F 6mm thick glass mirror of approved make with mirror screws all sides finished bevelled edging with 20-25mm tappered size completed all as specified and directed.

S& F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed.

S& F in repairs Brackets for item above complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes , water pipes (150 mm dia ) including all fittings, balance under credit ( measure overall as fixed along the centre line over fitting and accessories ) all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc., incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories)

M&L for 18/19 mm thick marine ply bonded with undiluted Phenol Formaldehyde resin, Boiled Water Proof, Specific gravity 0.80 (minimum), moisture content 8-12%, water absorption <5%, provided with and including 1mm thick plastic laminated sheet on both sides of plywood (plastic laminated sheet shall be with decorative choice lamination on one side and other side balancing) (Make of ply : Anchor, Kitply, Century Ply, Green Ply) as in kitchen cabinets, cub board, shelves etc, Fixed with screws to frame work, complete all as specified and directed, Note: Payment for glass panels shall be made for separatly as "supply only".

S&F D-handle of size 96mm long of stainless steel with matt or gloss finish for modular kitchen shutters, complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) n.exceeding 1.5 Sqm each including complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each including complete all as specified and directed.

S&FSolid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing all as specified and directed.

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 100 mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length

S&F 150 mm extruded aluminum alloy handles, fabricated type anodised

S&F aluminum anodised sliding door, bolts with hasp and staple ( bolt type ) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy, length of bolts 300 mm.

S&F bands, straps , supports or stays for rain water, ventilating pipes including bolts, clamps, hold fasts etc and similar small articles to Fe-290 Gde-E-165 all as specified & directed.

M& L for preparation surfaces of new or previsouly untreated wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

S&F Anodised aluminium sanp grid (size 605x605mm )frame work for false ceiling and gupsum false ceiling (size 600x600mmx9-10 mm ) and hangers 6mm dia. GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre incl dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets.complete all as specified

S & F 20 mm dia Ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S F for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F Toughned glass 12 mm thk as in hinged doors , partitions autometic doors and similar work incl cutting to shape , drilling holes requred incl adecute locking system fixed at bottom of door panel.

Supply only 30 cm long ornemental type stainless steel door handles fixed to 10/12 mm toughened glass door pattern and design as approved by GE.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 gde E

M & L for point wiring with PVC insulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn in and including PVC conduit with cheasel cut on wall / ceiling with all accessories, fittings, PVC junction boxes etc, with suitabe sunk pressed steel boxes for modular fittings not less than 1.6 mm thick, including Modular cover plate of suitable size etc with necessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 1.6 mm thick pressed steel terminal boxes concealed in wall mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws all as specified including Taking down carefully point wiring of any type & pattern (Light/Fan/Socket or power) including fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings of any type etc and making good disturbed surfaces of walls/ roof etc, for one light / fan / bell point controlled by one switch. Make of conduit: Precission/Pressfit/Anchor Make of Wire: Benlo/Polycab/KEI/Havells.

-Ditto- all as per item No 109 above but for one 5A 2pin/3pin switch socket out let multipurpose on independent Board.

All as per item No. 109 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board

M & L in repairs for point wiring with PVC insulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductor cable 2.5 Sqmm drawn in and including PVC concealed conduit of suitable size of wall/ RCC slab/ ceiling/ colunms/ beams etc with all accessories, fittings, PVC junction boxes etc, with suitabe sunk pressed steel boxes for modular fittings not less than 1.6 mm thick, including Modular cover plate of suitable size etc with necessary fixing accessories and earth continuity conductor cable of 2.5 Sqmm size connected to common earth and earth dolly including 1.6 mm thick pressed steel terminal boxes concealed in wall mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws including taking down old us wiring, fittings etc complete all as specified for one light / fan / bell point controlled by one switch. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. Make of conduit :- Sudhakar/ Precision/ Diamond, Make of wire :- Finolex/ Havells/ Polycab/ KEI/ Benlo

S&F modular type 6A one way SP switch 1 module with indicator of red light confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed. Make: Anchor Roma/Havells Reo

S&F modular type 2/3 pin combined shuttered type 6 Amps socket 2 module with conforming to IS: 1293-2005 complete all as specified and directed.Make: Anchor Roma/Havells Reo

S&F modular type 2/3 pin combined shuttered typr 16 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed.Make: Anchor Roma/Havells Reo

S&F modular type 16 A one way SP switch 1 module confirming to IS: 3854-1997 with finguer proof terminal complete all as specified and directed. Make: Anchor Roma/Havells Reo

S&F modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed.Make: Anchor Roma/Havells Reo

Supply & Fix Modular Bell push flush type 6 Amp, 1 module, 230 Volts complete all as specified and directed.Make: Anchor Roma/Havells Reo

Supply and fix bell ding dong AC 230 V single pole. complete all as specified and directed. Make: Anchor/Maru

S & F Modular Blank plate 1 module suitable for Modular switch boards all as specified and as directed

S & F Modular cover plate 8 modules

S & F Modular cover plate 3 modules

S & F Modular cover plate 2 modules

S & F Modular cover plate 1 modules

S&F ceiling rose three terminal, 230 Volts PVC / Polycarbonate body, complete all as specified and directed. Make: Anchor/Havells

Supply and fix surface/wall mountain, indoor decorative type LED luminaire extruded aluminium batten in anodized finished with opal diffuser, with IP 20 protection of capacity 18/20W having luminious efficiency not less than 100 lumen/watt, CCT 6500K4 feet long operating on 230V, 50 Hz, AC supply including fixing and mountaining on PVC blocks 02 Nos & connecting with 1.5 sqmm, 3 Core PVC insulated copper conductor and suitable nuts bolts & washers complete all as specified and directed. Make : Bajaj- Model No : BCLAV20W-LEDP, Halonix : HLB-03-18-CW-AL-SQ-HL2, Jaquar : LGLZU1X022XC, Wipro Note : The lowest tenderer shall furnished 3 years warranty certificate from OEM for luminiries including LM79 & LM80 test certificate from NABL certified laboratory.

Supply and fixing in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including provision with three core flexible copper conductor cable of suitable size and PVC square blocks complete all as specified and directed. Make - Bajaj/ Wipro/ Jaquar/ Halonix

Supply & fix in repairs Wall mounting fan 450 mm sweep, operating on single phase, 230V, AC, 50 Hz having speed of 1400 RPM, air delivery 115 CMM, power output of 100W star rated along with blade, canopy, mounting brackets, rubber insulator. Make - Bajaj ( model - 250439)/ ALMONARD / ORIENT

Supply and fix fans ceiliing with BLDC motor complete with blade, canopy, down rod, mounting hook, rubber insulator etc, the colour of fan shall be of Elegant White/Dubai white/ White CF without remote control alongwith accessories 230 V, 1200 mm sweep, BEE 5 Star rated complete including takingdown old unserviceable fan all as directed by Engr-in-Charge.Make : Havells (Efficiencia Neo (BLDC 26 W) /Orient FALCON 400 / Bajaj (ENERGOS 26) Note : Unserviceable ceiling fans shall be deposit to MES store.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and directed.Make: Bajaj/Anchor/Havells

Supply & fix in repairs Pedestal Fan 600 mm sweep, operating on single phase, 230V, AC, 50 Hz having speed of 1400 RPM, air delivery 115 CMM, power output star rated along with blade, canopy, mounting brackets, rubber insulator. Make - Bajaj ( model -Supreme Plus)/ ALMONARD-Air Circulator 24'' HSN Code: 84145910 / Usha Dominaire 600MM Pedestal Fan

Supply & Fix Heavy duty Metallic Body Exhaust fan of sweep 300 mm with frames, blades including provision of mounting anchor fasterners aluminium louvers made of aluminium sheet of 0.5 mm thickness provision of three core 1.5 sqmm copper cable from ceiling rose to fan, complete all as specified and directed .Make: Orient/Bajaj/Crompton/Almonard Note: Arrangement of ladders and scaff Holding for fixing of louvers if reqd is arranged by the contractor and its price is including in quoted rates.

Supply & Fix Heavy duty Metallic Body Exhaust fan of sweep 380 mm with frames, blades including provision of mounting anchor fasterners aluminium louvers made of aluminium sheet of 0.5 mm thickness provision of three core 1.5 sqmm copper cable from ceiling rose to fan, making opening of required size in cement mortar brick wall/ RCC for fixing of exhaust fan, making good the disturbed surfaces in CM 1:4 including scafolding if any required to carry out the work in building of height up to 20 meters complete.Make: Orient/Bajaj/Crompton/Almonard

S&F single pole and neutral enclosure with a two pin and earth and metal clad plug socket complete with one single pole MCB 20 Amp 240 Volts complete all as specified including concealing in wall and directed. Make :- LEGRAND/ SCHEINDER/ L&T

S & F MCB DB, 12 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete including taking down old warn out DB of any capacity/size all as specified and directed.Make: Indo asian/Schneider/L&T/Havells Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating.

S & F MCB DB, 4 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections including taking down old us DB complete all as specified and directed. Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating.

S & F MCB SPN 40 Amps, 240 / 415 Volts, 'C' Series, 50 Hz, 10 KA Breaking capacity complete all as specified and directed.Make -Havells/Indoasaian/Legrand/ABB/Schnider

-Ditto- all as per item No 137 above but for SP 5 to 32 Amps, 240V, 10KA 'C' curve miniature circuit breaker (MCB) complete all as specified and directed.Make: schneider,Legrand,Havells,indoasian

M&L for sub main wiring with two single core 6.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 6.0 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly including taking down old unserviceable submain wiring complete all as specified and as directed Make of conduit: Precission/Pressfit/Anchor Make of Wire: Benlo/Polycab/KEI/Havells. Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L for sub main wiring with two single core 1.5 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 1.5 Sqm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly including taking down old unserviceable submain wiring complete all as specified and as directed Make of conduit: Precission/Pressfit/Anchor Make of Wire: Benlo/Polycab/KEI/Havells. Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC Surface Mounted type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Jaguar/Bajaj/Halonix/Wipro.

S&F in repair/replacement of building Security light fitting 30/35 Watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings complete all as per directed by Engr- in – charge. Make : Bajaj/ Wipro /Jaquar

S& F in replacement of GI steel tubing medium grade 40 mm dia and length up to 1.5 meter bent to shape of offset angle upto 45degree for fixing of security /street light fittings including MS clamps made of 32mm x5mm flat iron, nuts , bolts, etc all as directed by Engineer in charge

Supply & fix GI cable tray with cover of size 300 mm X 100 mm including spacers, screws, saddles for fixing the trunking in wall/GI sheets of shed

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and not exceeding 10 sqm on plan and getting out in soft/loose soil for laying of cables, etc. complete all as specified and as directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm deep as in hard/soft soil complete all as specified and as directed.

Removing excavated materials to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point in soil including spreading in low lying area and leveling complete all as specified and as directed.

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out inhard/dense soil.

Excavation in post holes ( or similar holes) in hard/ dense soil ,each not exceeding 0.5 Cum , getting out returning , filling in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25 Cm, watering and removing surplus soil to a distance not exceeding 50M and making good surface complete all as specified

M&L for cutting existing road/hard standing not exceeding 45x50 cm in wide & depth getting out excavated material for laying GI tube, returning filling & well rammaing watering finish suraface 10 cm from top including provision of PCC 1:3:6 for repairing, including removal of surplus soil all as directed.

M&L for cutting existing road/hard standing not exc 45x45 cm in wide & depth getting out excavated material for laying cable/GI tube, returning filling & well rammaing watering finish suraface 10 cm from top using PCC 1:3:6; including removal of surplase soil all as directed

M & L brick work with sub class 'B' bricks in one brick walling built in CM 1:4 complete all as spoecified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan n.exceeding 6m mean radius built in CM 1:4 including Demolition of Brickwork of stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed.

M & L Brick work with sub class 'B' bricks in one brick thick honey comb walling built in CM 1:4 complete all as specified and directed.

M&L for preparation of newly plaster surface on walls applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as per manufecturer instruction and all as specified and directed

M& L for supplying, hoisting and fixing rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) as per IS 12701-1996 (Reaffirmed 2006) of 10000 Litres capacity with virgin food grade plastic, UV stabilized tank and lid, two layers protection with black outer layer for superior UV protection and white inner layer to see water leval and tank condition including covers, hoisted and fixed in position all as specified in SSR Part-I including connecting the overflow drain out, inlet and outlet pipes etc complete all as specified and as directed. Make-: Sintex/ Reno/ Plasto / Supreme

M& L for supplying, hoisting and fixing rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) as per IS 12701-1996 (Reaffirmed 2006) of 500 Litres capacity with virgin food grade plastic, UV stabilized tank and lid, two layers protection with black outer layer for superior UV protection and white inner layer to see water leval and tank condition including covers, hoisted and fixed in position all as specified in SSR Part-I including connecting the overflow drain out, inlet and outlet pipes etc complete all as specified and as directed. Make-: Sintex/ Reno/ Plasto / Supreme

Ditto all as per item No 157 above but 250 Liters capacity

Supply ,Laying, fixing, connecting and testing in repairs steel water tubing, medium grade, galvanised, with screwed and socketed joints, in any length, including supply and fixing all fittings, fixed to walls or laid in trenches / floors etc including taking out old u/s steel water tubing for the 15 mm bore complete all as specified and as directed , ISI marked. Make-: Tata/ Jindal/ BST/ Oswal

Ditto all as per item No 159 above but 20 mm dia bore complete

Ditto all as per item No 159 above but 25 mm dia bore complete

Ditto all as per item No 159 above but 40 mm dia bore complete

Ditto all as per item No 159 above but 50 mm dia bore complete

Ditto all as per item No 159 above but 65 mm dia bore complete

S&F sluice valve 65 mm bore, cast iron body, flanged drilled end, conforming to IS-14846, ISI marked, class PN 1.6, resilient seating as well as metal seating Fusion bonded epoxy coating including all joints with rubber gaskets, bolts and nuts, washers, iron wheel including taking up / down old unserviceable valves from any position and any addition / alteration for fixing required complete all as specified and as directed. Make :- Kirloskar / Leader / Kartar / Upadhyay

Ditto all as per item No 165 above but 50 mm dia bore complete

S&F in repairs gunmetal gate or globe valve for 25 mm diameter, conforming to IS-778, Class 2, ISI marked, Copper alloy body, Test pressure (Hydrostatic) for shell 2.4 Mpa and Seat & back seat pressure of about 1.6 Mpa with maximum working temperature of about 45 °C with iron wheel head screwed at both ends for iron pipes or ferrule and fixing including necessary fittings like unions, check nuts, etc and any addition / alteration required for fixing, complete all as specified and as directed. Make :- Leader / Zoloto / Shakti

S&F in repairs gunmetal gate or globe valve for 20 mm diameter, conforming to IS-778, Class 2, ISI marked, Copper alloy body, Test pressure (Hydrostatic) for shell 2.4 Mpa and Seat & back seat pressure of about 1.6 Mpa with maximum working temperature of about 45 °C with iron wheel head screwed at both ends for iron pipes or ferrule and fixing including necessary fittings like unions, check nuts, etc and any addition / alteration required for fixing, complete all as specified and as directed. Make :- Leader / Zoloto / Shakti

S&F Gunmetal gate or globe valve for 40 mm diameter, conforming to IS-778, Class 2, ISI marked, Copper alloy body, Test pressure (Hydrostatic) for shell 2.4 Mpa and Seat & back seat pressure of about 1.6 Mpa with maximum working temperature of about 45 °C with iron wheel head screwed at both ends for iron pipes or ferrule and fixing including necessary fittings like unions, check nuts, etc and any addition / alteration required for fixing, complete all as specified and as directed. Make :- Leader / Zoloto / Shakti

S & F cast iron Foot valve 65 mm, Ball type with flange joint model B-05 (N) conforming to IS with MS nuts bolts, washer, rubber gasket etc., any pattern as approved including taking out / dismantling old unserviceable one and testing complete all as specified and as directed. Make : KIRLOSKAR / UPADHAYA / LEADER / OR BEST AVAILABLE IN MARKET

Supply and fix 40 mm bore PVC Ball valve ISI marked high presssure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. Make -: Prayag/Shakti

S&F Centrifugal monoblock pump of capacity 5 Hp electrically driven horizontal end suction, centrifugal type confirming to IS-12469:1988 with CI casing, bronze impeller and stainless steel shaft mounted on heavy duty bearing suitable for continuous operation with range of operation 0% to 150% of rated capacity for 440V, 3 phase, 50 Hz, Head Range 33-42m and Discharge range 400-200 LPM complete all as specified and as directed. Make : Crompton, Kirloskar

Supply, installation, testing and commissining submersible pump set electric driven 3 phase, 415 volt, suitable for 150mm borewell discharge upto 750 Lit / min to 350 Lit / min at 9-41m head 5 stage not less than 5 HP etc complete all as specified as directed. Make- Kirlosker/CG/Havells

Supply and fix Pressure gauge of 4" dial 0-14 kgs rating with ball valve including taking up / down old unserviceable pressure gauge from any position and any addition / alteration for fixing required complete all as specified and as directed. Make: Warrie / H Guru / FIBIG

Supply and fix Air release valve of suitable size to release air locks from the pipe line complete all as specified and as directed. Make: Kirlosker /leader /L&T (Audco)

Supply and Laying cable passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 35 Sqmm 3.5 core including necessary connection and providing cable lugs as required all as specified. Make :- FINOLEX/ KEI/ POLYCAB/HAVELLS

Supply and Laying cable passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 16 Sqmm 4 core including necessary connection and providing cable lugs as required all as specified. Make :- FINOLEX/ KEI/ POLYCAB/HAVELLS

Supply & Lay XLPE insulated, armoured heavy duty 1100 volt grade electric LT UG cable with multistranded aluminium conductor of size 95 Sqmm 3.5 Core in trenches/along the wall/pole including making all connections complete as required at site and as directed by Engr-in-Charge Make: Havells/Polycab/Benlo/KEI

Supply & Lay XLPE insulated, armoured heavy duty 1100 volt grade electric LT UG cable with multistranded aluminium conductor of size 25 Sqmm 4 Core in trenches/along the wall/pole including making all connections complete as required at site and as directed by Engr-in-Charge Make: Havells/Polycab/Benlo/KEI

S&F Transciever automation for the water level Detector and controller with the feature mentioned here under comprising of following: (a) S& F Transciever must communicate at a distance of 3km -5kms range with each module must have the LORA/GSM or suitable communication module ( long range antenna) must work above 500 mhz and each module shall have a processor module connecting to the sensor, with the facility that the processor module to sense the low level (10-20%) and high level of the water level (90-100%) so as to raise the hooter and communicate with the other hardware modules with antennas (b) S&F transducer module wiring through the D sub connectors (MIL industrial grade are to be used). All the wiring must be shielded optical co-axial cable for connection to flasher and hooter. Rates quoted are deemed to be included for suitable flasher and hooter. (c) S&F Hooter 12V/5 Amp with suitable converter or hooter suitable for 230V AC Supply must be provided standard suspended rust proof stand Note: All the NPT cable glands must be used for the sensor interface and MCB controller board. (d) S&F 12V flasher with suitable converter or flasher suitable for 230V AC Supply connected with suitable 3 Core Co axial cable suitably crimped nicomatic connector. Note: All the cables to be drawn through suitable medium grade conduit suitably fixed with clamps. (e) S &F of LED display board with superior night vision display to be provided at the receiver station. (f) S&F controller Board confirming to IP 65 protection 3D printed with EMI/EMC compatible FE 32 material for the enclosure. Note: (a) One transmitter for over Head Tank and one receiver for Pump House . (b) Contractor has to visit the site before execution. Any cable required deemed to be included in quoted rate. No extra payment will be made on this account.

M&L for renewal of valve pit of size up to 80 cm x 80 cm x 80 cm (internal diamension), stone / brick construction including all necessary excavation and earth work in any type of soil, returning, filling in disposal of surplus soil to a distance not exceeding 50 m and depositing where directed, PCC in foundation for mix (1:2:4) type D2 brick mansonary in cement mortar (1:4) rendering 12 mm duck in cement mortar (1:4) internally ,finished even and fair and polishing flush externally as the work proceeds in the same mortor. Mild steel angle iron 40 x 40 x 6 mm frame MS sheet cover 3.15 mm thick with handle and locking arrangement, painting all exposed MS work with two coats of synthetic enamel paint of the that as approved by the Engineer - in - charge over a coat of red oxide primer and painting all the MS embeded in PCC with two coats of black bitumenous paint complete all as specified.

Supply, install, testing and commissioning Powder coated LT kiosk cubical outdoor type (double door openable) Channel mounted compartmentalized in construction all Confirming to IS 8623 Part 1 1993 CPRI approved factory as per CA fabricated made out of 3.15 mm thick CRCA sheet & suitable size to accomodate all accessories / fittings, to accommodate incoming MCCB and TPN Copper bus bars, incomer MCCB and outgoing MCCB, MCB, Contactors The TPN bus bars shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on DMC/epoxy insulator. The bus bar shall have copper extension links for connecting with out going MCCB. The cubicle shall have a bottom channel & free standing frame made of angle iron of size not less than 50mm X 50mm X 6mm of A detachable predrilled gland plate of thickness not less than 3 mm thick powder coated should be used at the bottom for entry of armoured cable of adequate size with glands.The above panel shall be front & back openable lockable /openable by key from both side.The panel shall be Dust, vermin proof and powder coated of approved thickness complete including CTs, control wiring by 1.5 Sqmm Wire and consisting the following. i) BUSBAR : One set of 150Amps rated copper bus bar suitable for 3 phase, 4 wire, 415volts system mounted on PVC/hygroscopic insulators and PVC colour coded sleeves of R,Y,B and green colour, complete arranged in separate compartment. Electrolytic Copper Busbar 150 A (15mm x 3mm) INCOMER MCCB 4 Pole, 50 A, 415V, 10KA-01 Nos OUTGOING (a) Fully automatic star delta starter having protection against single phase under voltage short circuit current for 5 HP centrifugal pump - 02 Nos (b) Digital panel meter with LCD multifunction meter with CT/PT and all parameters as V,A,F,PF,KW,KVAR,KWH etc (c) Phase indicating lamps RYB for incoming and each outgoing circuit connectionn (d) Single phase preventor for motors. (e) PCC foundation (f) Internal wiring with suitable size of pvc insulated stranded copper conductor duly crimped with copper lugs ferruled complete wiring of panel and installation. Note –: The Lay out drawing of the panel shall be got approved by the contractor from GE before the panel fabrication work.

M&L in repairs for provn of Earthing complete with M.S. galvanized earth plate electrode 600mmx 600mmx 6mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the plate not less than 2.50 M below normal GL, connected to Galvanized earth strip 32x6mm upto 7.5 mtr with protection pipe by means of bolts, nuts, check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 40mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Pt-I 2009 specification.

M&L for earthing using galvanised earth lead wire 4.0mm dia complete with galvanised steel earth plate electode 600mmx600mmx6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level connection to and including galvanised earth lead wire 4.0mm dia to the extend 7.5 mtr as earth lead by means of GI bolts, Nuts etc. with provision of charcoal and salt all as per electrical plate No 3 of SSR Part I including water arrangement with GI Pipe 20 MM dia (medium Grade), earth lead protection pipe 50mm madium grade with bends, elbow etc. from earth plate to test point, excavation and earth work returning, filling, ramming and removing of soil to distance not exc 50mtr, make good to match with existing surface making PCC pit (Earth chamber) having internal size 30cm x 30cm x 30cm and outer size 60cm x 60cm x 60cm with RCC reinforced cover 50mm thick with one lifting handle made of 8mm dia MS bar funnel wie mesh and testing on completion including making test point on wall as per SSR specification all as specified and directed. Note: (1) Rate quoted by the tenderer is deemed to include salt & Charcoal upto & above 450 mm top of GI earth plate.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250mm x 150mm x 40mm laid in trenches all as specified.Make: National/Mehtab Tiles

M & L for sand cushioning by spreading in trenches fine crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer -in-charge.

Supply and fix LT jointing kit of size 16 sqmm 4 core complete all as specified and directed

Supply and fix LT jointing kit of size 25 sqmm 4 core complete all as specified and directed

Supply and fix LT jointing kit of size 95 sqmm 4 core complete all as specified and directed

Supply, Fixing and connection of hot dip galvanised octagonal poles of height 6 mtr with 130mm bottom A/F & 70mm top A/F made up of 3mm thick HT sheet along with base plate of size 200 x 200 x 12mm thick including 4 nos of M20 x 600 long J type foundation bolts and 1 mtr long hot dip galvanised single arm standard bracket, including MCB of 6 Amps, with connector 4 way to be provided as termination point complete all as specified and directed.Make : BAJAJ/ ZENITH

M & Laying cement concrete for copying of poles using B1 1:2:4, 20 mm graded aggregate, smooth finishing without using extra cement complete all as specified and directed. .

M & Laying cement concrete for foundation fillings and mass conctere type C2 1:3:6 using 40 mm graded aggregate complete all as specified and directed.

Supply and fixing LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and rosion resistant complete with driver and lamp in multiple optics including MS clamps,bolts, nuts, washers, anchor fastners etc complete all as specifed and as directed. Make : JAQUAR/ WIPRO/Bajaj

S&F of HDPE pipe 50 mm dia, PN-10 for laying in ground, raod crossing etc for cable protection including necessary fittings, clamps for supports, etc complete all as specified and directed..

Sppply, errection and commissioning of high tensile steel (confirming to BS-EN10 025 Grade S 355) asymmetrical High Mast lighting system of 16 meter Height in two section of bottom dia 410 mm x 4mm thick and top dia 150 mm x 3mm thick provisioned with suitable size of door opening. The High Mast Pole shall Confirm to Cat No BHMRL16D of Bajaj / Crompton, including the following : - (a) Provision of pully system at top to accomodate ropes & electric cables, Provision of 08 Nos luminaries carriage made of ERW steel pipes designed to act as cable conduit with cable enty holes, luminaries fixing arms, junction box mounting bracket, carriage buffer arrangements. (b) Motorised & manual operating double drum winch raising & lowering system with, 1 No 1 HP motor, two continous 6 mm dia stain less steel wire rope, 5 core 2.5 Sqmm EPR insulated, PVC sheathed trailing power cables, junction box, multi core cables from junction box to individual luminairie all aser per recommandation of OEM (c) 25 mm thick base plate with 8 Nos of 30 mm dia & 850 mm long anchor bolts with nuts (d) 6 Nos - LED Flood light 350 Watts, with pressure die cast housing IP 65 protection, the fitting shall conform to cat no BJFL 350 W LED of Bajaj /Havells/Crompton (e) 01 Nos Integral aviation LED light comprising of aluminium housing with polycarbonate enclosure. (f) Counter weight as recommended by OEM for asymmetrical arrangement of lights. (g) PCC foundation drawing shall be as per manufacture's specification specified by OEM for High mast to suit Wind speed as per IS 875 Part III: 1987 including form work, excavation in any strata, refilling, removal as per the following specification:- (i) PCC base with PCC 1:4:8 with TMT bar 10mm dia. (ii) RCC M 20 footing using 10mm TMT bar @ 200 mm c/c both way (iii) RCC M 20 column using 24 Nos - 12 mm TMT bar (vert) and 10 mm dia stirrups @ 150 mm c/c (h) 01 No- LT Feeder panel, cubical out door type, factory fabricated from 3 mm thick CRCA sheet outdoor type of suitable size to accomadate all accessories / fittings, incommers, outgoings, bus-bars, other components/ parts etc. The cubicle shall be of free standing type with frame made of angle iron . A detachable predrilled mild steel gland plate of thickness not less than 3 mm thick powder coated shall be used at the bottom for entry of armoured cable of adequate size with glands. The panel shall comprise of the following i) MCB 32 Amps - 1 Nos ii) Single Dial Time Switch - 1 No iii) Three Pole MCB Contactor - 1 Set iv) Power Tool Control including 2 No 09 Amps Contactor v) Lower & Raise Push Buttons vi) Connectors for Incoming & Outgoing Cables vii) Internal wiring & any acessoroies recommended by OEM for the smooth operation of the High Mast Lighting System viii) Supply of dome aviation obstruction LED lamp fixtures. Note - (a) The contractor shall submit drawings & specification of OEM and shall be got approved before procurement. (b) Tha High Mast and LED light fittings shall be used of same make only.

Supply, installation, commissioning of Water cooler fully stainless steel, electric driven single phase having 120 Litre water storage capacity with inbuilt UV System complete all as specified and directed.Make : Bluestar SWCNST80120UVE./USHA SS60120RO. Note: Fixing will be done by the rep of manufacturers company and standard fittings inclusive in quoted rates.

M&L for cutting inserting and jointing of GI pipes for making connection complete all as specified and directed

Supply & Fix PVC insulated and PVC Round Sheathed, Multicore Annealed Bare Copper Conductor (flexible) 3 core 1.5 Sqmm industrial cable for Voltage Grade 1100 Volt, Conforming to IS 694 : 2010 for connection to Ceiling fan/exhaust fan complete all as specified and directed Make: Havells/Benlo/KEI/Anchor (Panasonic)

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd.Complete all as specified and directed.Make: Anchor/Havells/Legrand/Maru/Vinay/Leader

Supply and fixing drop down rod of steel white powder coated MS fan pipe of size 2 feet with provn to attach fan hook and nut bolts complete all as specified. Note : A sum of Rs 49,362.00 towards sch of credit shall be deducated to arrive the contract sum.

R.C. Magla and Co. (BID ID -3227629)

sapana enterprises (BID ID -3227640)

Parmatma Enterprises (BID ID -3232061)

Joy builders (BID ID -3227328)