ADDN/ALTN AND SPECIAL REPAIR TO BUILDING NO T-3 TO T-10 OF OFFRS MD ACCN AT RASPUNJA MILITARY CAMP UNDER GE (C) KOLKATA

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates. (ii) It is highlighted that the cretin condition of General Condition Of Contracts (IAFW-2249) has been modified as direction of MOD i.e inclusion of performance security, deletion of risk & cost provisions and increase in defects liability period all as specified in tender document. The tenderers should keep in mind while quoting their offer

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish to a distance n.exc 100m complete all as directed by the Engr-in-Charge

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) of any thickness including cover fillets complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed

Taking down chowkat or frame with shutter (without taking off shutters from the frame) n exc 1.5 Sqm each complete all as specified and directed.

All as per item No. 8 above but exc 1.5 Sqm and not exc 4 sqm each

Dismantling of wrought iron of mild steel work of any descrisption not otherwise privided for, complete all as specified and as directed.

Dismantling AC Corrugated, semi corrugated sheets in roof coverings including any type of ridges complete all as specified and as directed.

Dismantling timber scantling, 40 sqcm and over in section, in any position, in unframed work, complete all as specified and as directed.

Dismantling of timber fillets, rails, posts, rafters, purlins etc under 40 sqcm in section complete all as specified and directed.

Taking up or down 15mm bore, Steel tubing and connections complete all as specified and directed.

All as per item No 14 here-in-before but 20mm dia.

Material and labour for brick work with fly ash bricks , straight or curved on plan exe. 6 meters mean radius built in cement mortar 1:6 complete all as specified and as directed.

All as per item No 16 here-in-before but half brick thick wall in cement mortar 1:4 complete all as specified and as directed.

Supply and fixing mild steel TMT bars 10 mm dia and over cut to length and bent to shape as reqd, including cranking , bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed ) not less than 0.90 mm dia complete all as specified and directed .

Material and labour for reinforced cement concrete 1:1.5:3 (normal mix) type A1 using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, etc complete all as specified and directed

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, rough finished surface complete all as specified and directed.

Material and labour for PCC 1:3:6 type C-1 (20 mm graded aggregate ) as in bed blocks / holdfast including necessary form work complete all as specified and directed..

Material and labour for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed. Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ration 1:3 and cost of the same shall be deemed included in quoted rate.

Material and labour for 100 mm thick PCC 1:2:4 type B-2 (40 mm graded aggregate ) as in path / hard standing and finishing the top surfaces even and smooth with using extra cement complete all as specified and directed.

Material and labour for 25 mm thick PCC 1:2:4 type B-0 (12.5 mm graded aggregate) as in sub base of floor complete all as specified and directed.

Material and labour for 15mm thick rendering in cement mortar (1:4) on fair faces of brickworks or concrete surfaces finished even and smooth without using extra cement and using water proofing compund as per manufacturer instruction complete all as specified and directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on other than fair faces of brickworksor concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for rendering 5mm thick cement plaster in cement mortar (1:3) as in ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for complete removal of existing treatment and preparing old treated surfaces of wall and applying two coats of acrylic washable distemper over a coat of alkali resistant primer over one or more coats of water proof wall care putty complete all as directed.

Material and labour for preparing newly plastered surfaces of wall and applying two coats of acrylic washable distemper over a coat of alkali resistant primer including one or more coats of wall care putty to a smooth surface including making good any undulations on the surfaces complete all as specified and as directed.

Material and labour for complete removal of existing treatment and preparing old surfaces and applying two coats of water based acrylic weather proof exterior emulsion paint with silicon additives over a coat of exterior primer complete all as specified and as directed.

Material and labour for preparing newly plastered surfaces and applying two coats of water based acrylic weather proof exterior emulsion paint with silicon additives over a coat of exterior primer complete all as specified and as directed.

Material and labour for preparation of new wood or wood base surface of any description over 10cm width or girth and applying two coats of synthetic enamelled paint over one coat of pink primer complete all as specified and directed.

Material and labour for preparing old painted wood and wood based surfaces of any description not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as speciried and as directed.

Material and labour for preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure steam Crude Non Asbestos Fibre Cement plain Board (E-Board Classic) in a grid of GI system duly suspended with 4mm dia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall, Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid and painted with two coats of acrylic emulsion paint of approved shed /make over a coat of cement primer before installing it on the grid complete all as specified and directed.

Materal and labour for Double charged Light shade Vitrified, designed, coloured, tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, as in floors, etc with and including 15 mm thick screed bed in cement mortor 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

All as per item No 36 here-in-before but on vertical surfaces such as in skarting incl. 10mm thick rendering on fair faces of brickwork in CM (1:4) complete all as specified and directed.

Material and labour for ceramic non skid coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Supply and fixing glazed ceramic colour tiles (450 x 300 x 7mm thick ) in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick cement plaster in cement mortar 1:4 complete all as specified and directed.

Material and labour for granite stone slab (of any type) 18 to 20 mm thick, machine cut ,bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortor 1:6 & cutting, polishing and making moulds on edges as in steps, jambs, pillars, window cills, cooking platforms, urinal partition and like complete all as specified and directed.

Materal and labour for heavy duty exterior Vitrified tiles(full charged) of size 300x300x7-10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, as in floors, etc including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws compelte all as specified and as directed.

Supply and fixing pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges , valley gutter etc fixed with self tapping screws complete all as specified and directed.

Material & labour of MS rolled sections as in in roof truss (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) and fixed with angle cleats, Fe-410-W(Gde-E 250) Quality Acomplete all as specified and as directed. Note:- The drawing and design of truss shall be approved by the GE prior to incorporation in the work.

Supply and fixing rolled mild steel sections as in main and cross beams, hip and jack rafters;purlins where connected to common rafters fixed with angle cleats or other connecting plates complete confirming to Fe – 410-W Gde E-250 complete all as specified and directed

Material and labour for Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290(Gde E-165) complete all as specified and as directed.

Supply and fixing of pressed steel door frames (fabricated out of CRLCS sheet 1.6 mm thickness) 125 x 60 mm size with one or more rebates including necessary fixing lugs, hinges, lock striking plate etc. complete all as specified and as directed. Note:- Pressed Steel Frame shall be filled with PCC 1:3:6 type C-0 (Using 12.50 graded stone aggregate) and cost of same shall deemed included in Quoted rate.

All as per item No 47 here-in-before but of frame size 105 x 60mm complete all as specified and directed.

Supply and fixing 35 mm thick, Flush shutters, factory made ,solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to chowkhats complete all as specified and directed.

Material and labour for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut of 11 to 15mm dia, and 22.50 to 30.00cm long complete all as specified and directed.

Supply and fixing Welded steel wire fabric weight not more than 4Kg/Sqm fitted by ms nails complete all as specified and directed.

Supply and fixing 40 mm bore MS Tubes, medium grade' with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fixing 2nd class hardwood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, guaze etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section *, Clause 8.24(a); supplied and fitted to chowkhats as spefied in SSR Part-I 2009 complete all as specified and directed.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as directed and specified .

Supply and fixing solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with MS Square tube complete all as specified and directed.

Supply and fixingr in frame at site factory made solid PVC moulded Door shutter with wood free EPS, 28 to 30mm thick(stiles), with 2, 4 or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet Polyurethane painted on the front face & 2mm prelam PVC sheet on back face, complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth as in brick wall complete all as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

Supply and fixing of tinted sheet glass 4.80mm thick , pin head type and glazing in square exc 0.5 Sqm in each pane complete all as specified and directed.

Material and labour for 1.50mm thick powder coated aluminium(minimum thickness of powder coating 50 micron), three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos, anodised aluminiup snap beading screws etc complete all as specified and directed. Note:- (i) All window member inclluding fitting & fixture i.e. frame, track, shutter frame, etc shall be deem to include in quoted rate. Only measure opening size of window. (ii) Only Glass window & wire mesh shall be measured and paid separately.

Supply and fixing powder coated (minimum thickness of powder coating 50 micron) aluminium ventilators with louvers and glazing including frame of section over all size of window 600 x 450mm complete with following specifications:- (a) Aluminium frames of size 45x45x1.2mm (b) Rail & Stile 45x45x1.2mm thick (c) 5.00mm thick frosted sheet glass Note:- All ventilators / louvers member including fitting & fixture shall deem to include in quoted rate. Only measure opening size of ventilators / louvers.

Supply and fixing of end finials for drapery rod and including closed type stainless steel all brackets fixed on wall complete all as specified and directed. Make:- SOFFIO-II model of VISTA or equivalent model of NOVA.

Material & labour for drapery rod made of electric resistance welded MS pipe of 21mm dia having a coating of corrugated virgin PVC extrusion and cover with ABS plastic complete all as specified and directed. Make:- SOFFIO-II model of VISTA or equivalent model of NOVA.

Supply and fixing mild steel framed work such as grills, grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-410-0 Gde E-250 complete all as specified and directed.

Supply and fixing Aluminium (extruded section body) door closer hydraulically regulated,designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg complete all as specified and directed .

Supply and fixing for 40mm dia cupboad knobs , brass polished fixed with nut screws and washer complete all as specified and as directed.

Material and labour for 18/19 mm thick Medium density fibre board, exterior grade, fixed to timber framed work with screws complete all as specified and as directed.

Supply and fixing stainless steel sliding door bolt 300mm long with haps and staples (bolt type) and fixing clips of sheet and fixing bolts and sliding bolts complete all as specified and directed.

Supply and fixing stainless steel door stopper with hard drawn steel spring, overall length of cover plate 150 mm fixed in floor complete all as specified and directed

Supply and fixing stainless steel handle "D" type 150mm long complete all as specified and directed

Supply and fixing stainless steel barrel tower bolt 200mm long complete all as specified and directed

Supply and fixing 100mm butt hinges stainless steel complete all as specified and directed.

Supply and fixing 30mm width of flaps continous (Piano) hinges, brass, bright finish or electrogalvanised complete all as specified and directed.

Supply and fixing for 20mm outer diameter CPVC pipes SDR 11 and Plain CPVC SDR 11 fittings on walls / ceiling or laying in floors complete all as specified and directed.

All as per item no 74 here-in-before but 25mm outer diameter CPVC Pipes

Supply and fixing 110 mm bore PVC (SWR) pipe, single socketed in any length with rubber ring joints, fixed to walls with stack clamp every one mtr apart complete all as specified and as directed.

All as per item no 76 here-n-before but double socketed complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) bends of any radius without door complete all as specified and as directed.

Supply and fixing 110mm PVC(SWR) junction single, (single T) equal or unequal including jointing with solvent cement complete all as specified and directed.

Supply and fixing triple layer PVC water storage tank cylindrical, verticle with closed top, hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for 25mm outer diameter for CPVC pipe & making connection for inlet and outlet including dismental of old water tank and removing from site complete all as specified and directed .

Supply and fixing vitreous china (coloured) wash down water closet pan (pedestal pattern) including fixing with trap including fiixing with trap including matching PVC seat cover complete all as specified and directed.

Supply and fixing vitreous china light coloured pedestal pattern wash hand basin of size 550mm x 400mm incl providing 32mm dia CP wasted coupling, CP bottle trap bracket, 32mm dia PVC waste pipe and making all necessary connections complete all as specified and directed.

Supply and fixing in repair 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets conection to WC and making good disturbed surfaces complete all as specified and directed.

Supply and fixing 15mm bore fancy type chromium plated wall mixer for over head shower with 115mm long bend pipe on upper side,connecting legs & wall flange for mixing hot & cold water screwed down for CPVC pipe complete all as specified and directed. Make :- Jaquar model no CQT-23273 UPR or equivalent model of make Parryware ,Cera, Marc .

Supply and fixing in repair 15mm dia brass CP sink mixer with swivel spout wall mounted for mixing hot & cold water screwed down for CPVC pipe complete all as specified and directed. Make :- Jaquar model no CQT-23309 or equivalent model of make Parryware ,Cera, Marc .

Supply and fixing in repair 15mm dia chromium plated central hole wash hand basin mixer without popup waste system with 450mm SS flexible hose scewed down high pressure screwed for CPVC pipe complete all as specified and directed. Make :- Jaquar model no CQT-23167B or equivalent model of make Parryware ,Cera, Mark .

Supply and fixing in repair brass CP angle stop cock 15mm dia single way with wall flange screwed for CPVC pipe complete all as specified and directed. Make :- Jaquar model no CQT-23059 or equivalent model of make Parryware ,Cera, Marc.

Supply and fixing in repair 15 mm bore bib taps, two way fancy type screwed for CPVC pipe complete with wall flange all as specified and directed Make :- Jaquar model no CQT-23041 or equivalent model of make Parryware ,Cera, Mark .

Supply and fixing in repair CP sink cock with swinging spout (Wall mounted model) screwed for CPVC pipe complete all as specified and directed Make :- Jaquar model no CQT-23347 or equivalent model of make Parryware ,Cera, Marc .

Supply and fixing in repair 15mm fancy type chromium plated overhead shower, square of size (200x200) mm , with or without swivel joints, including CP shower arm and union complete all as specified and directed Make :- Jaquar model no 276017 or equivalent model of make Parryware ,Cera, Marc .

Supply and fixing PVC bathroom cabinet (white) of size 430 x 330 x 100 mm (approx) with one single shutter and built in mirror in front of shutter including taking down old unserviceable one complete all as specified and directed Make:- Prayag(Cat no 551) or equivalent model of make Parryware, Cera, Polytuff

Supply and fixing stainless steel kitchen sinks without drainage board made of 1 mm thick steel sheet for kitchen with plugs, washers, including bedding in cement mortar for fixing cantilever bracket and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including taking down old unserviceable one complete all as specified and directed

Supply and fixing PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Supply and fixing in repair chromium plated towel ring round with round flange complete all as specified and directed . Make :- Jaquar model no ACN-1121BN or equivalent model of make Parryware , Cera, Marc .

Supply and fixing in repair 600mm long towel rod complete all as specified and directed .Make :- Jaquar model no ACN-1111SM or equivalent model of make Parryware , Cera, Marc

Supply and fixing in repair health faucet with 1.2 m long PVC tube & wall hook complete all as specified and directed. Make :- Jaquar model no ALD-563 or equivalent model of make Parryware , Cera, Marc

Supply and fixing in repair corner glass shelf with brackets complete all as specified and directed. Make :Jaquar model no ACN-1173 or equivalent model of make Parryware , Cera, Marc

Supply and fixing stainless steel utencil plate rack (size 24" x 30' x 10") using 0.8mm thick sheet including taking down old unserviceable one complete all as specified and directed .

Material and labour for diameter of outlet 75mm UPVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed .

Taking down carefully existing aluminium/copper point wiring on batten or in PVC conduit or in MS conduit with GI earth wire etc (for light, fan, socket or power ) complete and making good the disturbed surfaces of walls, Floors, ceilings etc to match with existing all as specified and directed.

Material and labour for concealed point wiring with FRLS PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with FRLS PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC conduit terminated in switch boards for fixing of switches, sockets, fan regulators etc for One light / Ceiling fan / exhaust fan/ call bell controlled by one switch complete all as specified and directed

All as per item No 101 here-in-before but one 3 pin switch socket outlet 5A on independent board complete all as specified and directed

All as per item No 101 here-in-before but using 2.5 Sqmm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board complete all as specified and directed by Engineer-in-Charge.

All as per item No 101 here-in-before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-Charge.

Material and labour for switch socket combination 2 in 1, 3 pin switch socket outlet 5A on independent board complete all as specified and directed

Supply and fixing switch socket combination multi-purpose 3 pin, 15 amp and 5 amp controlled by one switch, flush type complete all as specified and directed

Supply and fixing socket outlet 2 in 1, 3 pin 5 Amps on the same board with other switch complete all as specified and directed

Supply and fixing switch paino flush type single pole one way 5 Amp complete all as specified and directed

Supply and fixing ceiling rose, surface bakelite 65 x 50mm three terminals complete all as specified and directed

Supply and fixing Bell push switch, fllush type 5 Amp complete all as specified and directed.

Supply and fixing Bell ding dong, AC 230 volts, single pole complete all as specified and directed.

Supply and fixing lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Refixing LED lamps of any capacity after taking down old serviceable one complete all as specified and directed .

Refixing LED light fittings of any capacity suspended type / wall mounted type complete with LED tube lamp and fitting with copper flexible PVC cable of 0.50 Sqmm twin core not more than one metre in length after taking down old serviceable one complete all as specified and directed .

Supply and fixing ceiling fan enery saving and fancy type 1200 mm sweep three blade, , 50 watt maximum,Air delivery 210 Cum per Mintus (minimum),, colour /white , BEE starshall not be less than 3 as per latest notification of BEF and conform to IS 374: 2019 without regulator including hanging rod, canopy, writing the MES fan numbers with paint and including 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed. Make: Model- ES 40 of Havells or equivalent model of USHA/ BAJAJ/CROMPTON GREAVES/ORIENT as approved by GE.

Supply and fixing exhust fan 240V, 300 mm sweep, 1400 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on ball bearings and conforming to IS: 2312 and including aluminium louers and shutters fixed to wall and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan after taking out old unservceable one and deposit to E/M store complete all as specified and directed by Engr-in-Charge.

Supply and fixing five star rated Storage water heater 25 ltrs cap 2 KW AC 230 Volts vertical mounting,white colour including connecting cord and 15 Amp 3 pin plug, safety valve, nuts and bolts, complete including grouting of nuts and bolts in wall and making good the disturbed surface also depositing the old one to MES store yard complete all as specified as directed. Make : Havells Senzo GHWASESWH025 Ltrs or equivalant model of make Bajaj,Venus

Taking down unserviceable / rusted / damaged MCB DB of any type along with MCB any type and keeping serviceable MCB in safe custody in re-use in the work and making good to the disturbed surfaces of walls etc complete all as specified and directed.

Supply and fixing MCB DB made up with sheet metal, phosphorised, power coated, neutral link, earth bar and din rail, 8 way TPN with 200 Amps rated bus bar, 240 volts complete all as specified and directed .

All as per item No 119 here-in-before but MCB's to be used 8 Way single pole neutral with 200 amps rated bus bar complete all as specified and directed.

All as per item No 119 here-in-before but MCB's to be used 4 Way single pole neutral with 200 amps rated bus bar

Supply and fixing MCB 'C' series single pole (SP) 6 to 32 Amps, breaking capacity 10KA. ,240 volt complete all as specified and directed.

Supply and fixing MCB 'C' series SPN 6 to 32 Amps, breaking capacity 10KA. ,240 volt complete all as specified and directed.

Supply and fixing MCB TPN 63 Amps, 415 Volts, C-Curve breaking capacity 10 KA complete all as specified and directed.

Material and labour for electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed.

Supply and laying in trenches or fixing on wall or passing through pipe, connecting and testing, 11000 volts grade, stranded aluminium cunductor of cross sectional area 35 Sqmm 3.5 core , XLPE insulated ,screened, heavy duty electric cable with , galvanised steel strip or wire armoured with aluminium conductor after taking out old unserviceable cable complete all as specified and directed

All as per Item No 126 here-in-before but 16 Sqmm 2 core complete all as specified and directed.

Material and labour for Sub main wiring with two runs of 6 sqmm (Nominal area) single core cable FRLS PVC insulated, multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through PVC conduits/casing-caping of suitable size, fixed to wall/ceiling etc including one run of 6 sqmm (nominal area) single core, FRLS PVC insulated, multistranded, unsheathed, copper conductor as earth wire and duly connected to common earth point including PVC conduits/casing-caping of suitable size including taking down old sub main wiring complete all as specified and as directed by Engineer-in-charge. Note : PVC Conduits/Casing-caping, two run cables and one run of earth wire will be measured as one length.

Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to 4.0mm GI wire (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no 5 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm long reinforcement, watering funnel, 40 mm dia light grade for protection of earth electrode 20 mm dia for watering all as specified and directed and tested on completion including dismantling old one.

Excavating in trenches, not exceeding 1.5 metres wide and not exceeding 1.5 metres depth for laying of cables / foundation of poles and getting out in soft / loose soil complete all as specified and directed

Returning, filling in incl spreading, levelling, watering and well ramming in layers not exceeding 25cm in soft / loose soil complete all as specified and directed

Removing excavated n.exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soft / loose soil complete all as specified and directed

Material & labour for providing sand cushioning for protection of underground cable with dry (coarse) sand approved quality including filling, spreading and punning down to desired thickness complete all as specified and as directed.

Supply and layng well burnt bricks sub class "B", laid, breath wise along the length of cable in trenches for underground cable protection complete all as specified and directed.

Material and labour for 40mm bore GI tubes light grade for cable protection supporting to poles with all fixing accessories (clamps, nut, bolt and washer etc) complete all as specified and directed.

Cutting roads / hard standing to a depth not less than 45cm and not less than 40cm wide for laying of GI pipe to draw the UG cable and making good the disturbed surfaces by filling of PCC(1:3:6) type C-2 using 40mm graded stone aggregate and finished the surface even and smooth without using extra cemenbt and disposed off the surplus debris and soil to a distance not exc 50m complete all as specified and directed.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

MS SHRI B.C. DAS

PEARL CORPORATION

R.K.TRADING CO. INDIA