Loading
Loading…
Loading…
Tender Value
₹1.5 Cr
EMD Value
₹3.1 L
Closing Date
18 May 2026, 11:00 amClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
45 days
Expenditure
Capital (Works)
DEN/HQ/UBL
24 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payment" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the Previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant / Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) Attested Certificates(s) issued by Executive or Nominated Authority of the government Departments or Semi-Government/Public Sector Undertakings for the value of the work done for them during the qualifying period including current financial year certifying the bill amounts paid Agreement-wise and Date-wise or attested photo copy of such certificate. Such certificates will be accepted only from Govt. / Govt. bodies / PSUs authorities. Certificates issued by Private Bodies will not be considered.
NOTE: (i) Financial Year shall normally, be reckoned as 1st April to 31st March of the Next Year. However, for Turnover Criteria, the Financial Year as applicable to the Company /Tenderer is to be considered, if it defers from the above. (ii) Current Financial year is reckoned as the incomplete Financial year in which the date of tender submission falls. (iii) Chartered Accountant statements duly indicating yearly receipts will not be considered until and unless backed by Audited Balance Sheets or Provisional Balance sheet. (iv) (v) If the tender is not accompanied by the certificate(s) in support of financial eligibility as above, the tender shall be rejected. No post-tender correspondence will be entertained.
If JV firms are allowed to participate; Financial eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.2 of J.V guide lines of IRSGCC April - 2022 [with up to date correction slip].
(a) The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Tenderer shall carefully read clause No. 10 including clause no. 10.1 to 10.5 of IRGCC April 2022.
The total value of similar nature of work completed during the qualifying period and not the payments received within qualifying period alone, shall be considered. In case, final Bill of similar nature of work has not been passed and final measurements have not been recorded, the paid amount including statutory deductions will be considered. If final measurements have been recorded and work has been completed with negative variation, then also the paid amount including statutory deductions will be considered. However, if final measurements have been recorded and work has been completed with positive variation but variation has not been sanctioned, original agreement value or last sanctioned agreement value whichever is lower shall be considered for judging eligibility.
In case JV firms are allowed to participate, Technical Eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.1 of J.V. guide lines of IRSGCC April-2022 [read with up to date correction slip].
The value of work completed will not include the cost of any materials issued free of cost by the Railway/ Department concerned. Price Variation amount, if any; if indicated / incorporated in the experience certificate will also be considered towards eligibility.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organization, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates.
The work experience certificate shall be in the name and style of the tenderer participating or as per provisions under Clause 17.15 of GCC 1.5.1 April-2022 for JV Firm, if eligible to participate. [with up to date correction slip].
The work experience certificate shall be issued by an officer not below the rank of JA Grade or Bill passing Officer in Railways and Bill passing Officer/Executive In-charge of work in other Govt. / Govt. bodies / PSUs. The certificate should bear the signature and seal of the issuing officer, name of the department etc. In case tenderer submits work experience 1.5.2 certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Defination of Similar Work :- Any building work or concrete work
75 conditions · 20 needing a document upload
Proforma-16 for self-certificate in regard to meeting the Minimum Local Content requirements as per Make in India Policy for Procurement order value less than of Rs. 10 Crores. OR Proforma-17 for Certificate from the statutory auditor or cost auditor of the company (in the case of companies) or from a practicing cost accountant or practicing chartered accountant (in respect of suppliers other than companies) giving the percentage of Local Content as per Make in India Policy for Procurement Order Value more than Rs.10 Crores. Provisions of Make in India Policy 2017 (revised during 2024 vide Department for Promotion of Industry and Trade, Ministry of Commerce and Industry's letter No. P-45021/2/2017-PP (BE-II)-Part(4)Vol.II dated 19.07.2024) issued by Govt. of India, as amended from time to time, shall be followed for consideration of tenders
Uploading of Proforma -18 attached with Tender document (Certificate signed by Tenderer and Chartered Accountant), w he n balance sheet for the first previous year is yet to be prepared/ audited.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
(i) The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii) documents shall be submitted according to clause 14 of IRGCC 2022:
The General Conditions of Contract governing the performance of the works covered by this tender are the Indian Railway Standard General Conditions of Contract [IRSGCC] as amended from time to time up to date. A soft copy of the Indian Railway Standard General conditions of Contract is uploaded in the attached documents to the tender for reference. Hard copy of IRSGCC (with up-to-date correction slip) may be perused in the office of the Principal Chief Engineer Officer/ South Western Railway / Hubballi - 580020. The tenderer/s is/are deemed to have kept himself/themselves fully Informed of the provisions of the IRS General conditions of Contract including all corrections and Amendments issued up to date while submission of offer and any claim that he/they is/are not aware of any amendment or correction slip to the IRSGCC shall not be entertained.
STUDY OF DRAWINGS AND LOCAL CONDITIONS: The drawings for the works can be seen in the office of the General Manager/Divisional Railway Manager. It should be noted that these drawings are meant for general guidance only and Railway may suitably modify them during the execution of work according to the circumstances without making the Railways liable for any claims on account of such changes. If there is any variation between the description in the tender and the detailed plans, the Engineer-in-Charge will operate the correct description and his decision is final and binding on the tenderer/ Contractor. The Tenderer/Contractor is required to inspect the sites of works and acquaint himself with the site conditions, availability of approaches for transporting of men and materials, space and other factors relating to the works, availability of labour, electricity and water, etc., before quoting his rates. The extent of lead and lift involved in the execution of works and any difficulties involved in the execution of work should also be examined before formulating the rates for complete items of works described in the schedule. The Tender submitted will be deemed to have been made after such inspection.
DRAWINGS FOR WORKS: The percentage rates for the schedule items and itemized rates for the non-scheduled items quoted by the tenderer as may be accepted by the railways will, hold good irrespective of any changes, modifications, alterations, additions, omissions in the locations of structures and detailed drawings, specifications and/or the manner of executing the work. It should be specifically noted that some of the detailed drawings may not have been finalized by the Railway and will, therefore, be supplied to the contractor as and when they are finalized on demand. No compensation whatsoever on this account shall be payable by the Railway Administration. No claim whatsoever will be entertained by the Railway on account of any delay or hold up of the works arising out of delay in approval of drawings, changes, modifications, alterations, additions, omission and the site layout plans or detailed drawings and design and/or late supply of such material as are required to be arranged by the Railway or due to any other factor on Railway Accounts.
Manual tenders, supporting documents etc., sent by Post/FAX/Courier or in Person SHALL NOT BE ACCEPTED.
All requisite documents are to be properly submitted online only and the bidders should ensure that the content of the documents uploaded is distinctly legible /readable.
CORRIGENDUM NOTICE ON IREPS: Railway may modify the tender document by issuing online corrigendum through "www.ireps.gov.in" 15 days prior to the tender closing date. For the purpose of CORRIGENDUM in the tender, NIT period is splitted as under: (a) ADVERTISEMENT PERIOD: The time during which all information pertaining to tender shall be available but offers cannot be submitted (b) OFFER SUBMISSION PERIOD: 15 days prior to closing of tender, during which tenderers can submit their offer.
No Technical and Financial credentials are required for tenders having value up to Rs 50 lakh. For tenders valuing more than Rs. 50.00 lakh: The offer of Tenderer(s) who do not enclose Experience Certificate & Turnover Certificate with requisite details, and supporting documents along with their Tender to establish their credentials shall be summarily rejected, even though they are working contractors or contractors on approved list.
The offer shall be evaluated only from the certificates/documents submitted along with the tender offer.
Any Certificate /Documents offered / submitted /received after the tender opening shall not be given any credit and shall not be considered.
Attestation of documents may be self attested or attested by a Gazetted Officer.
Railwayreservestherighttoverifythe authenticityofthe documents/information furnished.
IRSGCC para 6.0 of part-I (a)(ii) Tenderers will examine the various provisions of The Central Goods and ServicesTax Act, 2017(CGST)/ Integrated Goods and Services Tax Act, 2017(IGST)/ Union Territory Goods and Services Tax Act, 2017(UTGST)/ respective state's State Goods and Services Tax Act (SGST) also, as notified by Central/State Govt.& as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit (ITC) likely to be availed by them is duly considered while quoting rates. (a)(iii) The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/ UTGST /SGST Act to railway immediately after theaward of contract, without which no payment shall be released to the Contractor. The Contractor shall be responsible for deposition of applicable GST to the concerned authority. (a)(iv) In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/ SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism (RCM) and deposit the same to the concerned authority. (b) When work is tendered for by a firm or company, the tender shall be signed by the individual legally authorized to enter into commitments on their behalf. (c) The Railway will not be bound by any power of attorney granted by the tenderer or by changes in the composition of the firm made subsequent to the execution of the contract. It may, however, recognize such power of attorney and changes after obtaining proper legal advice, the cost of which will be chargeable to the Contractor.
Increase/decrease of TAXES: if rates of existing GST or cess on GST for Works Contract is increased or any new tax /cess on Works Contract is imposed by Statute after the date of opening of tender but within the original date of completion/date of completion extended under clause 17 & 17A and the Contractor thereupon properly pays such taxes/cess, the Contractor shall be reimbursed the amount so paid. Further, if rates of existing GST or cess on GST for Works Contract is decreased or any tax/cess on Works Contract is decreased / removed by Statute after the date of opening of tender, the reduction in tax amount shall be recovered from Contractor's bills/Security Deposit or any other dues of Contractor with the Government of India.
Fixed Deposit Receipts (FDRs) submitted after award of tender towards Security Deposit/Performance Guarantee should be with automatic renewal facility only.
CONSORTIUM AGREEMENTS AND MOUS SHALL NOT BE CONSIDERED FOR PARTICIPATING IN THIS TENDER.
Tenderer(s) shall note that conditional/alternate offer will not be considered and will summarily be rejected, even though such condition makes them as the lowest tenderer.
Shramik kalyan While processing payment of any 'On Account Bill' or 'Final Bill' or release of 'Advances' or 'Performance Guarantee / Security deposit', contractor shall submit a certificate to the Engineer or Engineer's representatives that "I have uploaded the correct details of contract labours engaged in connection with this contract and payments made to them during the wage period in Railway's Shramikkalyan portal at 'www.shramikkalyan.indianrailways.gov.in' till ____Month, ____Year.
Date of inviting tender shall be the date of publishing tender notice on IREPS website if tender is published on website or the date of publication in newspaper in case tender is not published on website.
Hubballi Division: Hubballi-Improvements to old hospital old building at Gadag road, Hubballi (Balance work) (Maintenance Period- 03 Years)
03UBL26-27DT240426ITEM01
03UBL26-27DT240426ITEM01
Open
Works - General
8 Months
Dharwad, Karnataka
₹0
₹3.1 L
18 May 2026
24 Apr 2026
4 May 2026
115 items across 2 schedules · ₹16,02,109.55 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 600 | 177.5 | 1,06,500 |
| 2 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum | 20 | 2,123.75 | 42,475 |
| 3 | Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared. | Sqm | 600 | 8.95 | 5,370 |
| 4 | cum | 2 | 6,658.25 | 13,316.5 | |
| 5 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 20 | 7,878.5 | 1,57,570 |
| 6 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 167.91 | 7,294.7 | 12,24,853.08 |
| 7 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources). | Sqm | 150 | 495.75 | 74,362.5 |
| 8 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 190 | 392.15 | 74,508.5 |
| 9 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. | Sqm | 50 | 842.5 | 42,125 |
| 10 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 610 | 927.25 | 5,65,622.5 |
| 11 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 644.85 | 736.4 | 4,74,867.54 |
| 12 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 256.68 | 961.3 | 2,46,746.48 |
| 13 | Stairs, (excluding landings) except spiral- staircases | Sqm | 85.55 | 764.95 | 65,441.47 |
| 14 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 160 | 9,504.75 | 15,20,760 |
| 15 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 214.05 | 9,860.4 | 21,10,618.62 |
| 16 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 150 | 9,105.95 | 13,65,892.5 |
| 17 | Providing and laying Autoclaved Aerated Concrete (AAC) blocks masonry with 150 mm to 300 mm thick with Grade -1 AAC blocks of density 551 to 650 kg/cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in- Charge. (The payment of RCC band and reinforcement shall be made for separately). | cum | 25 | 8,333.65 | 2,08,341.25 |
| 18 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 60.8 | 7,311.25 | 4,44,524 |
| 19 | Area of slab over 0.50 sqm | Sqm | 300 | 3,078.4 | 9,23,520 |
| 20 | Each | 10 | 978.7 | 9,787 | |
| 21 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | Sqm | 350 | 1,267.95 | 4,43,782.5 |
| 22 | Second class teak wood | cum | .05 | 1,42,949.7 | 7,147.49 |
| 23 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 34.96 | 3,167.95 | 1,10,751.53 |
| 24 | 5 mm thick solid foam PVC panel of required size with moulded/ extruded beading of appropriate design shape and size as per manufacturer's specifications ( to secure the panel insert tight in place within the style and rails of shutter) matching the colour and shade of shutter frame. Non decorative type | Sqm | 3.57 | 3,754.2 | 13,402.49 |
| 25 | 1.5 mm thick | Sqm | 350 | 1,045.95 | 3,66,082.5 |
| 26 | Providing and Fixing factory made uPVC door frame, made of uPVC extruded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm ( +/- 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm ( +/-0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fasteners, all complete as per manufacturer's specification and direction of Engineer-in-charge. | Metre | 60 | 623 | 37,380 |
| 27 | Using R2 series with frame (40 mm & above) x (40 mm & above) & sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 metre). | Sqm | 35 | 8,298.85 | 2,90,459.75 |
| 28 | Using R1 series with frame (33mm & above ) x (35mm & above) & sash /mullion (33mm & above) x (50 mm & above). (Height upto 0.90meter). | Sqm | 43.28 | 13,201.2 | 5,71,347.94 |
| 29 | Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete. | Each | 8 | 204 | 1,632 |
| 30 | Providing and fixing steel (white powder coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete. | Each | 28 | 198.3 | 5,552.4 |
| 31 | Providing and fixing 19 mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails, screws etc. complete as per direction of Engineer-in-charge. | Sqm | 175 | 2,593.15 | 4,53,801.25 |
| 32 | 200 mm | Each | 50 | 186.65 | 9,332.5 |
| 33 | Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. | Each | 20 | 272 | 5,440 |
| 34 | Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in- charge. | ONE SET | 20 | 885.1 | 17,702 |
| 35 | Providing and fixing 2 mm thick 16 to 19 mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in- charge. | Metre | 150 | 43.8 | 6,570 |
| 36 | Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete. | Each | 30 | 226 | 6,780 |
| 37 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 46.47 | 772.4 | 35,893.43 |
| 38 | Ordinary cement without any pigment | Sqm | 200 | 1,056.35 | 2,11,270 |
| 39 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | Sqm | 150 | 1,096.55 | 1,64,482.5 |
| 40 | Size of Tile 600x600 mm | Sqm | 230.32 | 1,553.45 | 3,57,790.6 |
| 41 | Size of Tile 800x800 mm | Sqm | 494.36 | 1,885.5 | 9,32,115.78 |
| 42 | Size of Tile 600 x 1200 mm | Sqm | 7.2 | 1,798.8 | 12,951.36 |
| 43 | Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red | Sqm | 100 | 3,071.05 | 3,07,105 |
| 44 | 12 mm thick | Sqm | 100 | 924.35 | 92,435 |
| 45 | 110 mm diameter | Metre | 45.8 | 377.4 | 17,284.92 |
| 46 | 110 mm | Each | 10 | 136.15 | 1,361.5 |
| 47 | 110x110x110 mm | Each | 8 | 234.15 | 1,873.2 |
| 48 | 110 mm bend | Each | 9 | 150.35 | 1,353.15 |
| 49 | 110 mm Shoe | Each | 6 | 131.85 | 791.1 |
| 50 | 110 mm | Each | 50 | 371.3 | 18,565 |
| 51 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) | Sqm | 600 | 1,355.8 | 8,13,480 |
| 52 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 50 | 738.65 | 36,932.5 |
| 53 | 1:4 (1 cement: 4 fine sand) | Sqm | 1850 | 347.05 | 6,42,042.5 |
| 54 | 1:3 (1 cement : 3 fine sand) | Sqm | 600 | 300.45 | 1,80,270 |
| 55 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm | 2600 | 262.7 | 6,83,020 |
| 56 | Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm | Sqm | 3500 | 193.7 | 6,77,950 |
| 57 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture | Sqm | 400 | 176.25 | 70,500 |
| 58 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture | Sqm | 250 | 170.7 | 42,675 |
| 59 | With cement mortar 1:4 (1 cement : 4 fine sand) | Sqm | 400 | 547.4 | 2,18,960 |
| 60 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 40 | 2,434.25 | 97,370 |
| 61 | In cement mortar | cum | 30 | 2,060.2 | 61,806 |
| 62 | Of area 3 sq. metres and below | Each | 20 | 143.5 | 2,870 |
| 63 | For thickness of tiles 10 mm to 25 mm | Sqm | 300 | 73.4 | 22,020 |
| 64 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer- in-charge, beyond 50 m initial lead, for all leads including all lifts involved. | cum | 100 | 263.95 | 26,395 |
| 65 | Moorum | cum | 586 | 768.25 | 4,50,194.5 |
| 66 | W.C. pan with ISI marked white solid plastic seat and lid | Each | 2 | 6,515.55 | 13,031.1 |
| 67 | One urinal basin with 5 litre white P.V.C. automatic flushing cistern | Each | 11 | 6,258.75 | 68,846.25 |
| 68 | White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap | Each | 1 | 1,879.2 | 1,879.2 |
| 69 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. | Each | 12 | 1,683.35 | 20,200.2 |
| 70 | White glazed fire clay kitchen sink of size 600x450x 250 mm | Each | 5 | 3,892.75 | 19,463.75 |
| 71 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. | Each | 2 | 349.15 | 698.3 |
| 72 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. | Each | 12 | 1,034.8 | 12,417.6 |
| 73 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality and make as approved by Engineer in charge.(a) 15 mm nominal dia | Each | 12 | 6,940.75 | 83,289 |
| 74 | Size 600x450x200 mm | Each | 2 | 4,077.65 | 8,155.3 |
| 75 | 40 mm dia | Each | 3 | 119.55 | 358.65 |
| 76 | Providing and fixing 100 mm sand cast Iron grating for gully trap. | Each | 4 | 53.25 | 213 |
| 77 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | Each | 12 | 1,607.95 | 19,295.4 |
| 78 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. | Each | 12 | 1,083.5 | 13,002 |
| 79 | C.P. brass | Each | 12 | 803.7 | 9,644.4 |
| 80 | Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms | Each | 2 | 122.4 | 244.8 |
| 81 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. | Each | 12 | 168.35 | 2,020.2 |
| 82 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. | Each | 12 | 231.95 | 2,783.4 |
| 83 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. | Each | 12 | 708.95 | 8,507.4 |
| 84 | 15 mm nominal dia Pipes | Metre | 318.2 | 497.8 | 1,58,399.96 |
| 85 | 50 mm nominal dia Pipes | Metre | 200 | 794.25 | 1,58,850 |
| 86 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Per Litre | 25000 | 11 | 2,75,000 |
| 87 | 15 mm nominal bore | Each | 24 | 506.8 | 12,163.2 |
| 88 | 15mm nominal bore | Each | 15 | 574.3 | 8,614.5 |
| 89 | 150 mm dia. R.C.C. pipe | Metre | 50 | 556.45 | 27,822.5 |
| 90 | 250 mm dia. R.C.C. pipe | Metre | 50 | 899.8 | 44,990 |
| 91 | Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) | Kg | 260 | 539.85 | 1,40,361 |
| 92 | Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side | Sqm | 110 | 1,139.3 | 1,25,323 |
| 93 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) | Sqm | 77 | 1,176.8 | 90,613.6 |
| 94 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. | Sqm | 150 | 617.05 | 92,557.5 |
| 95 | P r o v i d i n g and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric water proofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric water proofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. | Sqm | 480 | 563.1 | 2,70,288 |
| 96 | 50mm average thickness | Sqm | 100 | 256.35 | 25,635 |
| 97 | Bars upto 12 mm diameter | Metre | 100 | 8.25 | 825 |
| 98 | Upto and including 12mm dia. | Each | 40 | 141.2 | 5,648 |
| 99 | Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make | Sqm | 100 | 285.2 | 28,520 |
| 100 | Epoxy injection grout in concrete/RCC work of approved make | Kg | 50 | 553.4 | 27,670 |
| 101 | Wooven PVC cloth | Sqm | 200 | 54.25 | 10,850 |
| 102 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 36.04 | 7,387.25 | 2,66,236.49 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TenderDocument6.1new.pdf
ATTACHMENT
IRGCCApril2022.pdf
ATTACHMENT
JPOCirculardated22.05.2024.pdf
ATTACHMENT
NEFTFORM.pdf
ATTACHMENT
AnnexureVGCCcorrespondence.pdf Annexure V
ATTACHMENT
ACSItoXI_compressed.pdf
ATTACHMENT
BUILDINGCONDITION.pdf
ATTACHMENT
BGverificationletter_compressed.pdf BG Verification Letter
ATTACHMENT
AnnexureVGCCcorrespondence.pdf
ATTACHMENT
BGverificationletter_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .