PROVISION OF 01 X RECORD ROOM IN 155MM GUNANDHOWITZERS CELL, PROVISION OF RAIN WATER SHED IN FRONT OF TSII, PROVISION AND FIXING OF STAINLESS STEEL RAILING AROUND MAIN OFFICE BUILDING, IMPROVEMENT OF STAFF IN QAD-II SECTION, PROVISION AND INSTALLATI

Amount

Excavating in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & getting out in soft/loose soil

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil.

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point

Hardcore of Broken stone/boulders gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface

M&L PCC in foundations, filling and mass-concrete type D2 (1:4:8) using 40 mm graded stone aggregate

Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6)

M&L Nominal mix M20 (1:1 1/2 :3) Type A-1 using 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete

M&L Nominal mix M20 (1:1 1/2 :3) Type A-1 using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span

M&L Nominal mix M20 (1:1 1/2 :3) Type A-1 using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter Rough finished surfaces of concrete flat

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200m thick (Horizontal or sloping) Fair finished surfaces of concrete flat

M&L TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality

M&L TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete. Note : Liquid WPC will be measured and paid separately.

M&L for preparation of new wall surface and applying two coats of cement base paint over a coat of primer including preparation of surface.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 1000 Ltrs Capacity

S&F Ball brass valves 25mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule

S&F Gun-metal, globe or gate valves 25mm bore, with iron wheel head, screwed both end for iron pipe

S&F 15mm bore GI tubes, medium grade galvanised, with all fitting; complete all as specified and directed.

S&F 20mm bore GI tubes, medium grade galvanised, with all fitting; complete all as specified and directed.

S&F 25mm bore GI tubes, medium grade galvanised, with all fitting; complete all as specified and directed.

Supply only Integral water proofing compound all as specified and directed.

Taking up or down steel tubing 15mm dia and connectins, including cleaning for re-fixing or removal to store

Taking up or down steel tubing 20mm dia and connectins, including cleaning for re-fixing or removal to store

Dismantling floor, hearth or wall tiling in-cluding cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceedeing 0.18 sqm but n.exc 0.38sqm, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM (1:6).

Material and labour for Glazed ceramic tiles of size 350x 250x 7mm/ 450X 300X 7mm thick in vertical surfaces such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 all as specified

Dismantling of water tanks of capcity exc 500 and n exc 1000 ltrs and removing to store

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity

S&F Ball brass valves 25mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule

S&F Gun-metal, globe or gate valves 25mm bore, with iron wheel head, screwed both end for iron pipe

Taking down Chowkats or frames with shutter without taking off shutters from the frame exc. 1.5 sqm and n exc 4 sqm each

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 all as spd.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed all as spd.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F in repair vitreous china WHB size 550x400 mm white flat back including pvc waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc complete.

S&F in repairs white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed.

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete.

S&F in repair chromium plated health foucet with 8mm dia and 1.2 m long flexible tubes and wall hook suitable for EWC including nut/washer complete.

S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and as directed.

S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete.

S&F in repair 15 mm dia stop valves, fancy type chromium plated, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe for unions and fixed

S&F in repair 15 mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete.

M&L for PVC (SWR) floor trap of 75mm dia plain with grating including jointing with solvent cement

S&F in repair soap dish, vitreous china white, approximate size 160c160x90mm embedded in the wall

S&F in repair plastic water closet seat cover, Cream / white colour, closed pattern with flat bottom and cover and mild steel chromium plated aluminium hinging device for pedestral pattern WC.

S&F toilet paper holder, vitreous china, coloured, box type fixed to wall with chromium plated (CP) brass screws.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors

S&F PVC (SWR) bends any radius 110mm dia

S&F in repair CP bib taps, cast copper alloy with crutch or butterfly handle, screwed for iron pipe 15mm dia fixed.

Applying two coats of Distemper oil emulsion, white or tinted on old wall surface including preparation of surface.

Applying two coats of Distemper oil emulsion, white or tinted on ceiling including preparation of surface.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in & raming earth/ broken rubble mixed with earth around, in layers n. exc. 25cm, watering, & removing surplus soil to a distance n exc 50m & making good surface in soft/loose soil.

M&L PCC in foundations, filling and mass-concrete type C2 (1:3:6) using 40 mm graded stone aggregate

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in & raming earth/ broken rubble mixed with earth around, in layers n. exc. 25cm, watering, & removing surplus soil to a distance n exc 50m & making good surface in soft/loose soil.

M&L PCC in foundations, filling and mass-concrete type C2 (1:3:6) using 40 mm graded stone aggregate

S&F structural steel work of tubular trusses/verticke post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 rade St.-240 all as specified and directed.

S&F Rolled mild steel Plates (plain or chequered) channels. Square cut or notched (ordinary & counter sunk) forming holes, without any attachment GDE Fe410-0 or Fe 310-O

S&F Rolled mild steel sections as in main & cross beams, hip & jack rafters; purlins where connected to common rafters & running rails & guides for sliding doors; fixed with angle cleats or other connecting plates GDE Fe410-0 or Fe 310-O

S&F Mild steel screw bolts (machine made) with hexagonal / square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut, n exc 5cm long dia of shank 5 to 10 mm

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with 'J' or "L' kooks as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F MS hand rails, half round or other section for wind ties for roof, brackets for valley gutter including securing bolts; , drilling holes, notching all as specified and directed.

M&L for painting steel & iron two coats of synthetic enamel paint over a priming coat of red oxide including preparation of surface all as specified and directed.

Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, n exc 10cm width or girth when unconnected with other painting or when painted in different tint, including preparation of new surface & applying one coat of red oxide, zinc chrome

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed..

Formwork to sides of pillars, posts, struts columns, and stanchions of square, rectangular, polygonal, rough finished surfaces of concrete completed all as specified and directed

M&L brick work with sub class 'B' old size bricks straight or curved on plan exc 6m mean radius built in CM 1:4 all as specified and directed

M&L 15mm thick Renedering on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick surfaces in CM (1:4) finished surfaces even and smooth without using extra cement complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including back side painted with black japan, complete all as specified and directed.

M&L 35 mm thick 2nd class Hard wood (Factory Made) Plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L 35mm thick (2nd class hardwood) (Factory made ) Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, cla-use 8.20 (a); supplied and fitted to chowkats complete all as specified and directed

S&F factory made steel windows with side hung shutters including projecting type hinges with lugs steel handles and steel peg stays, with glazing bars, devetailed or welded complete all as specified and directed.

Ditto all as per item No 79 above but without glazing bars

M&L Mild steel work framed such as grills,gratings etc. with ends of bars souldered or or rivetted or forged into spikes,framed guard bars,frame works of water tanks and similar work complete all as specified and directed conforming to Fe-250 Gde-165.

S&F 100mm long Butt hinges MS cold rolled (medium wight) complete all as specified and directed.

S&F 300mm long aluminium alloy.anodised, sliding door bolt with hasp,staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section and fixed of size 125mm long complete all as specified and directed.

S&F aluminium anodised handle fabricated type of size150 mm complete all as specified and directed.

M&L PCC (1:3:6) Type C1 using 20mm graded agg as in Coping, bed block for hold fast complete all as specified and directed.

M&L for preparation of new plastered surfaces and and applying two coats of cement base paint over a coat of white cement primer on walls complete all as specified and directed

M&L for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces over 10 cm width or girth including preparation of new wooden surfaces complete all as specified and directed.

M&L non skid coloured Ceramic tiles 8 to 10mm thick (square/rectangular) polished, area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over & including 15mm thick screed bed in CM(1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade o floor complete all as specified and directed.

M&L moorum/red bajri filling in floors or pavings laid in layers nexc 15cm thick spread levelled and rammed including watering complete all as specified and directed.

M&L 100mm thick PCC (1:4:8) type D-2 (40 mm graded stone aggregate) as in sub base, finished even and fair complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone agg) as in plinth protection laid to slope in bays and finishing the surfaces of concrete topping fair and even and exposed edges fair or rounding or chamfering laid in panels with and including all necessary form work and filling the joints with mastic filling of one part of hot bitumen 85/25 grade and three part of fine sand (all by weight) complete all as specified and directed.

M&L 40mm thick cement concrete type B-1(1:2:4) (20 mm graded stone aggregate) as in floor finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces and and applying two coats of cement base paint over a coat of white cement primer on walls complete all as specified and directed

M&L for three coats of white wash (lime) on newly plastered surfaces on wall including preparation of new plastered surfaces complete all as specified and directed

M&L 3mm thick wallcare putty on walls complete

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm (Profiled) thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall of mangalore pattern design, fixed with self tapping screws as specified & directed

S & F mild steel flat iron as in wind tie for roof including securing bolts.

Schedule of credit amount of Rs. 1843.00 to be deducted during AOC

m/s R K SETHI