Proposed Construction of New Building and Renovation Work of Existing Building at Government Womens Polytechnic, Dumka for Developing it as a State of the Art Institution.

Amount

Fine Dressing of Ground as per instruction and specification of E/I

Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with disposal upto 1000 metres. (Excavation for roadwork in soil with hydraulic excavator of0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m)

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.Rate per cum for grading-I Material

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing coarse clean sand in filling in foundation trenches or plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts includng cost of all materials, Labour, rotalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume).

Providing designation 75Bwork in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). Roof Slab

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering texes royalty all complete as per building specification and direction of E/I.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto plinth level Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125mm thick reinforced designation 75A brick work in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement0 all complete as per building specification and direction of E/I.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I.

Providing Toe steel reinforcement of 8mm dia to 32mm dia rods as approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (Only Valid for SAIL & TATA STeel)

Add for using extra cement in the items of design mix over and above the specified cement content therein.

S/F M.S. grill made of 20 x 6mm M.S. flat as per approved design and drawing, properly fabricated with joints continous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction ofE/I. (Where materials is not supplied by the deptt.)

Providing and fixing fan hooks of 16mm dia M.S. bar & 1 meter long, bent torequired size and shape, placed in position and fixed in the R.C.C.slab/beam at the time ofcasting all complete as per building specification and direction of E/I.

S/F local make fully glazed steel door, windows or ventilation of standard rolled 'Z' and mullion steel section and size as per IS - 38 joints met welded with 100 x 16 x 3mm M.S. lug fixed in cement concrete (1:2:4) blocks, 15 x 10 x 10cm size including cost of oxidized iron fitting with hinges, handle per step catch springs, 3mm thick plain glass panes with aluminum beads and inner frame fixed with lugs with 20mm long 6.3mm GI. counter sunk machine screw and nuts and applying a coat red lead paint carriage to work site hoisting and plcing in all position in all storys and taxes all complete as per building specification and direction of E/I.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I.

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

Providing 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing two coat of oil bound distemper of approved shade and make over a primer coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding, washing floors and taxes all complete as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over old surface including washing cleaning and preparing the walls scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning removing dirt scales smoke, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

S/F 35mm thick solid core type non-decorative single leaf flush door and windows with black board core banded with high quality phenol formaldehydes synthetic resin both side commercial veneered of standard make with oxidized iron fittings such as hinges, sliding door bolts tower bolts, handles or rings hooks and eyes, cleats sand block as per schedule taxes and royalty all complete as per building and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Providing & Fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/ suede finish with high density protectivesurface layer and reverse side of adhesive bonding quality conformingto IS : 2046 Type S, including cost of adhesive of approved quality.

Structural steel work riveted, bolted or welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position andapplying a priming coat of approved steel primer all complete.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).

Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specificatio).

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down chaukhats in doors including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking sown chaukhats in windows including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Providing 150mm wide brick drain in cement mortar (1:6) with as. 150mm clear depth and 250mm apron including cost of earthwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Water proofing for Old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed ready to use, acrylic modified flexible material applied with brush, roller or spray for water proofing coating as per manufacturer specifications with following steps :- (a) Surface preparation :-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jel including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equivalent. Providing and reparing of all corners and joints such as those between the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer Repairing surface irregularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.

Covering of treated surface wrth PCC :- Providing 25 mm thick Cement Concrete M20 (1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F M 2.5 io 3 including screening,shuttering,and mixing cement concrete in mixer with admixture of integral water proofing and placing in position,striking curing,taxes and royality all complete as per building specification and direction of E/l. Panels that has been left should be casted next day.-There should be 6 mm gap between Panels. Brand- Sika_Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421 ic , Dr Fixit Pidiproof LW+

Providing and filling of 6mm thick Groove between 25mm PCC panels with Polysuplhide sealant (Poring Grade) as per drawing and techinical speicifcation and direction of E/I.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20mm nominal size ) over 75mm bad by dry brick ballast 40mm nominal size well rammend and consolidated and grouted with fine sand including finishing the top smooth.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use ofchequered plate wherever required, all complete In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in?charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement andmatching pigments etc., complete.

Kota stone slab flooring over 20 mm (average) thick base laid over andjointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying vitrified Paring / Industrial tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 4457:2007, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 x 10 mm sizes.

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Labour for laying, fitting and fixing NP2 R.C.C. spu pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complete as per specification and direction of E/I. 150mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.

38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with sea; ring conforming to IS:5382, leaving 10mm gap for thermal expansion, Single socketed pipes

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler - 110mm

Bend - 110mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surfaceto prepare the surface even and smooth complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin-Charge. 80mm thick Cement concrete paver block of M-30 gradewith approved colour, design & pattern.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion - Powder coated aluminium (minimum thickness of powdercoating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) - Powder coated aluminium (minimum thickness of powdercoating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose of measurement the entire treated surface will be measured.

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Providing and supplying aluminium extruded tubular and otheraluminium sections as per the architectural drawings and approvedshop drawings , the aluminium quality as per grade 6063 T5 or T6as per BS 1474,including super durable powder coating of 60-80microns conforming to AAMA 2604 of required colour and shade asapproved by the Engineer-in-Charge. (The item includes cost ofmaterial such as cleats, sleeves, screws etc. necessary forfabrication of extruded aluminium frame work. Nothing extra shallbe paid on this account).

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof.

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm,having NRC (Noise Reduction coefficient) of 0.50 (minimum) as perIS 8225:1987, Light reflectance of 85% (minimum). Non combustibleas per BS:476 (part-4), fire performance as per BS:476 (part 6 &7),humidity resistance of 100%, thermal conductivity < 0.043 W/m Kas per ASTM 518:1991, comprising of a frame made from especiallyfabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.verticalstuds of size 48 x 34 x 36 mm are placed at 600mm center tocenter in a floor and ceiling channel section of size 50 x 32m fixedto the floor and soffit at 600mm centers using 12mm dia,50mm longwedge type expanded zinc alloy dash fastner with 10mm bolt. Thissame channel is then to be fixed in horiziontal direction at 600mmcenter to center so as to form a grid of 600mm x 600mm. Glasswoolof 50mm thickness is then to be inserted in the slots and finallycalcium silicate non combustible panels/tiles are to be screw fixedwith self tapping pan head nickel coated mild steel screws of size13 x 3.2mm on to this grid leaving an even groove of 1 mm betweenthe panels. The joints between the panels are to be duly jointed andfinished using recommended jointing calcium silicate basedcompound and fiber joint tape roll 50mm wide (90 metre )roll andtwo coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete. With 15 mm thick fully perforated square/butt edge lightweight calcium silicate panels/ tiles

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 micronsminimum to avoid scratches during transportation and should besupplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto anypitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Flashings/ Aprons.( Upto 600 mm)

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge

Stainless steel wire guage (Grade-304) aperture 1.4 mm and 0.50mm dia wire

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 150mm dia

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages(2 HP)

FR PVC insulated 3 core 4 sq.mm copper wire

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Direction and Place Identification signs upto 0.9 sqm size board. (Providing and erecting direction and place identification retro-reflectorised sign asper IRC:67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing)

Direction and Place Identification signs with size more than 0.9 sqm size board. (Providing and erecting direction and place identification retro- reflectorised sign asper IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)

Supplying fitting & fixing G.I. pipes (Tata make) or equivalent as per I.S. 1239 (part - I)/2004 ISI marked OR medium quality (50mm dia)

Carriage of materials

Bricks Lead = 1 k+7 P(8km)

Fly Ash Brick - 15km

Sand lead = 10 km

Stone chips lead = 22 km

Stone metal lead = 22 km

Local Sand lead = 3km

Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. not less than 350 gms.) with extra socket all compere as per specification and direction of E/I.

Providing and fixing N.P./C.P. brass/PVC procelain shower rose of 15mm inlet etc. all complete as per specification and direction of E/I.

Shower Rose - 125mm

Providing & fixing 15mm size pillar cock C.I. body brass spindle pillar cock of approved quality as per specification & direction of E/I.

Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I.

15 mm dia

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.

Horizontal - 25 mm dia

Horizontal - 32 mm dia

Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I.

125 mm thick wall

250 mm thick wall

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Mirror (300 x 450mm)

C.P. brass tower rail

C.P. brass soap container medium quality with screw and hinges etc.

Supplying, fitting and fixing viterious white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'p' trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair or viterous white glazed earthenware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 580mm long - With 12.5 lit. low level PVC cistern

Supplying, fitting and fixing 40mm highb viterous white glazed earthen E.W.C. with 'P' trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fitting with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stope cock of approved quality weight not less than 450 grams 15mm PVC alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic soild state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming all complete as per specification and direction of E/I. With 'P' trap - 12.5 lit low level PVC Cistern

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware urinal of 'Hindustan "Parry" or any other approved I.S.S. make with 5 liters capacity C.I. automatic flushing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S., brackets, standard size G.I. flush pipe with fitting clamps, 15mm, C.I. body brass spindle stop cock of approved quality weight not less than 400 grams, 15mm P.V.C./Alkthene pipe 450mm long with brass coupling at both ends and doing plumber joints including painting coat of red oxide cutting wall and floor making good the same etc. all complete as per specification and direction of E/I. (a)Flat back or Standing Cornar

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on pointed C.I. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms. 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 150mm dia

Approved basic rates construction materials for preparation of schedule of rates only, (Material should conform to relevent B.I.S. specification). The rates are inclusive of all taxes, royalty, cess and carraige but exclusive of contractor's profit and overhead charges - Special type of C.P. Bath room fitting for V.I.P. buildings (JAL, Jaguar, Marc or equivalent mark)

Angular Stopcock /2 way bib cock

Telephonic shower flexible pipe

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee without door - 75x75x75 mm

Single tee without door - 110x110x110 mm

75 mm bend

110 mm bend

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Point Wiring in PVC Conduit, with Modular type Switch:- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.

Group A

Group B

Group C

Supplying and fixing batten/ angle holder including connection etc. as required.

Twin Control Point Wiring in PVC Conduit, with Modular type Switch: Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate, suitable size of GI box etc as required.

Power Plug wiring in PVC Conduit (2X4 Sq.mm) :- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.

9/10 Watt LED Bulb

S.I.T.C of following rating LED Street lighting luminaire with pressure die cast housing and toughened glass cover, IP66 protection, luminous efficacy >10LM/W with lens in existing pipe/pole for supply voltage 100-270V AC, 50Hz.Luminaire shall conform to IS:3022 part-5/ section-3 and shall be complete with all necessary accesories as required.

70W LED street light

S.I.T.C of following rating LED floodlight fitting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC, 50Hz. Luminaire shall conform to IS:3022 part-5/ section-5 or IEC:62722 with all necessary accesories as required.

80W LED Flood light

150W LED Flood light

S.I.T.C of following rating recess/surface mounting round/square shape downlight with pressure die cast housing for single phase supply voltage. Luminaire shall conform to IS:3022 part-5/ section-2 or IEC:62722 with all necessary accesories as required.

Supply fitting fixing of Recess Mounting LED Round Down light (12W)

2' X 2' LED Panel Light (34W)

18/20W LED Round Downlight

Supply of LED Street light (45/48W)

Supply and installation of Ceiling fan 48" (1200mm)

S.I.T.C of following rating surface mounted LED tube lightfitting suitable for 230V 50Hz, single phase supply etc. complete as required.

20w/22w LED tube

S.I.T.C of following rating approved make LED bollard fitting with cylindrical shape and inverted cone shape head of height 600 to 850mm power input 8/9 watt with die cast aluminium housing opel with PC diffuser, IP:65/54 protection, conferming to IS:10322 part 5 etc all complete as required. (excluding plinth charges)

SITC of 2x20W LED Tube light.

Supply of 9 metre hot dip galvanised Octagonal pole(BOP-9031) with top dia 70mm, bottom dia 130mm & made of 3 mm thick sheet, base plate dimensions 200 x 200 x 12 mm(LXBXT) including suitable sizes of foundation bolt all complete as reqd. (without arm)

Supply of 1m single arm suitable for 70mm top

Supply of 1m double arm suitable for 70mm top

12" (300mm) Exhaust fan

16" (400mm) Wall fan

Installation, testing & commissioning of 9 mtr high octagonal pole & light fitting with the help of suitable tools and plants, wiring of luminaires with all materials and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity of 10T/sq.mtrs.

Installation of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of he above fan making good the damage, connection, testing, commisionig etc as required.

S/F Modular type electronic fan regulator :- Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

Supply, fitting, fixing and testing of 1200mm Sweep, BLDC, 5Star Fan.32 W

S/F light plug point with modular type accessories :-Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc, as required.

S/F light plug point with modular type accessories :- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

S/F Ceiling Rose:- Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Batten / Angle Holder:- Supplying and fixing batten / angle holder including connection etc as required.

ITC fluorescent fitting directly on surface:- Installation, testing and commissioning of Pre-wired fluorescent fitting /compact fluorescent fitting of all types, complete with all accessories and tube etc.directly on surace or ceiling/ wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supplying and fixing 20 amps 240V, SPN industrial socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP MCB insheet steel enclosure on surace or in recess with chained metal cover for the socket outlet and complete with connections, testing & commissioning etc.

S/F Modular boxes, base & cover plate :- Supplying and fixing following size/ modules G.I. box along with modular base & cover plate for modular switches in recess etc as required.

4 module (78mm x 140mm x 50mm)

6 module (78mm x 205mm x 50mm)

8 module (78mm x 230mm x 60mm)

12 module (135mm x 205mm x 60mm)

S/F Modular type blanking plate :-Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor single core cable in surfacce/ recessed medium class PVC conduit.

4x6 Sqmm +2x6 sqmm earth wire.(to be used for all LDB & UPS DB.)

4 X 10 sq. mm + 2 x 6 sq.mm Earth Wire

4 X 16 sq. mm + 2 x 6 sq.mm Earth Wire

2 X 4 sq. mm + 1 x 4 sq.mm Earth Wire (Sockets)

2 X 2.5 sq. mm + 1 x 2.5 sq.mm Earth Wire (Switch Boards)

2x1.5 Sqmm + 1x1.5 sqmm earth wire(for Single Separate 5A from nearest switch board and wall fans)

Supplying and drawing following pair 0.5 sqmm FR PVC insulated copper conductor unarmored telephone cable in the existing surface/conduit

S/F piano type switch/socket - Supplying and fixing following piano tyep switch/socket on the existing switch box/cover including connections etc. as required.

5/6 amps, one way switch

3 pin 5/6 amps, socket outlet

Supplying and fixing following modular switch/socket on the existing modular plate & switchbox includingconnections but excluding modular plate etc.

5/6 amps, one way switch

3 pin 5/6 amps, socket outlet

Telephone socket outlet

TV antenna socket outlet

S/F light plug point with piano type accessories - Supplying and fixing suitable size G.I./PVC box on surface or in recess with phenolic liminated sheet cover in front including providing and fixing 5 pin, 5/6 amps socket outlet and 5/6 amps piano tyep switch connection, painting etc. as required.

S/F Busbar chamber:-providind and fixing following capacity Busbar chamber with 4 strips of suitable size made of copper,heavy duty, complete with all accessories including connections, earthing the body,etc as required.

S/F 'B' series, S.P. MCB - Supplying and fixing 6 amps to rating, 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commossioning etc. as required. 6/32 amps, single pole "B" series

Copper earth pipe electrode :- Earthing with G.I. earth pipe 4.5mtr. long 40mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt as required.

P/F 25mm x 5mm copper earth strip in surface/ recess :- Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc., as required.

S/L 25 mm x 5 mm G.I. earth strip in ground :- Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including soldering etc.

P/F G.I. lightning conductor finial :- Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

EG.I. earth plate electrode :- arthing with G.I. earth plate 600mm x 600mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

COPPER EARTH PLATE ELECTRODE:- Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required.(2 Nos. for Main Panel,2 Nos. for APFC panel, 4 Nos. for xmer, 4 Nos. for DG set.)

Salt & Cock for plate earth elecrode :- Providing and fixing salt and cock for G.I. & copper plate earth elecrode etc. as required.

S/L 8 SWG copper wire in ground (for main panel and APFC panel) :- S/L 8 SWG G.I. wire in ground :- Supplying and laying 8 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

P/F 25 x 5mm copper earth strip in pipe :- Providing and fixing 25mmx5mm cpper earth strip in 40mm & 4.5Mtr long G.I.pipe for earth electrode etc. as required.

P/ F G.I. Lightning conductor tape in horizontal run :- Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete etc. as required (horizontal run).

P/ F G.I. Lightning conductor tape in vertical run :- Providing and fixing G.I tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete etc. as required (vertical run).

Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 35 sq mm but not exceeding 95 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 95 sq mm but not exceeding 185 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 185 sq mm but not exceeding 400 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

1.1 KV Cable End Termination:- Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.

3.5c x 240 sq.mm (62mm)

3.5c x 185 sq.mm (57mm)

3.5c x 150 sq.mm (50mm)

3.5c x 70 sq.mm (38mm)

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed armoured electrical cable with aluminium conductor for working voltage upto 1.1 KV etc as required.

Supplying PVC/XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor- 3.5 core, 95 sq.mm

3.5c x 150 sq.mm

3.5c x 240 sq.mm

3.5c x 185 sq.mm

3.5c x 35 sq.mm

1 R for each floor separately ,3.5 Core 50 Sq. mm. 1.1 KV XLPE Al. Ar. Cable from Main LT Panel to VTPN L.D.B Panel.

3.5c x 70 sq.mm

4c x 10 sq.mm

4c x 16 sq.mm

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding not 35 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

1.1 KV Cable End Termination:- Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.

3.5c x 35 sq.mm (32mm)

S/F T.P. MCB DB:- Supplying and fixing following way three pole & neutral ,sheet steel, MCB distribution board, 415 volts, onsurface /recess, complete with tinned copper bus bar, neutral bus-bar, earthbar ,dinbar, interconnections, powder painted including earthing etc. as required.

4 Way (4+12) Double Door, Horizontal type

4 Way (4+18) Double Door, Horizontal type

Supplying and fixing 6 amps to 32 amps rating, 240 volts, 10kA 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connection, testing & commissioning etc. as required.

63A rating, TPN MCB, "C" curve 10 KA breaking capacity.

63A rating, TPN MCB, "C" curve 10 KA breaking capacity.

6/32A rating, SPN MCB, "C" curve 10 KA breaking capacity.

Supplying and fixing following rating four pole, (three phase and neutral) 415 volts, residual circuit breaker (RCCB) having a sensitivity current 30 milli amperes in the existing MCB DB complete with connection, testing & commissioning etc. as required.

Supply of 9/10 Watt LED Bulb

Supply fitting fixing of Bulk head fitting with 9/10 watt CFL/LED

1.5Tr. 5 Star split A.C (Inverter Type) I91391-part-I

Copper Tube of size 7f 2" for split ac tl;:ritT/7.S/2/3 tr capacity includins nitride rubber insulation

4 KVA wall mounted automadc voltage stablizer from range 140V to 280V

Drain Pipe for AC

Outdoor stand for 1.5Tr Split AC

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/1S 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required

200mm dia

150mm dia

100mm dia

80mm dia

65mm dia

50mm dia

40mm dia

32mm dia

25mm dia.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 a)mplete with rubber qasket. Gl bolts, nuts, washers etc.as required 100mm dia.

80mm dia.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of I .6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 MM

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 100mm dia

80mm dia

65mm dia

Supplying and fixing Single headed extemal yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/StainIess Steel and chain as reauired • a) Single Headed

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe With 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. conforminq to IS 636 (type-A) as required Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe couolinq as required: Gun Metal

Supply, erection, testing & commissioning of electrical motor driven main pump of horizontal In Line Type end suction pump capable to deliver 2850LPM against head of 60M (to ensure a minimum pressure of 3.5 Kg/Sqcm at the farthest or topmost Hydrant) . Fire pump shall have C.I. casing, bronze impeller (hard finished and dynamically balanced) and S.S. (304) Shaft with mechanical seal. The installation shall be complete with necessary pressure gauge with gun metal shut off cock on delivery side. (The pump should be tested for bench mark at factory and shall be gotten approved by the Local fire Authority). (HYDRANT PUMP) HYDRANT PUMP 2280LPM,60M HEAD

Supply, Installation, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supplywith IP 55 protection for enclosurewith F class insulation confirming to IS: 325 includingcommon base frame fabricated from min. 75X50 mm M.S channel, coupling with guard foundation bolts, pressure gauge, anti-vibration pads, cement concrete foundation etc. complete in all respect as required or as directed by engineer incharge. JOCKEY PUMP 180 LPM, 60 M head

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle, Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 mtr.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : 18.21.1 Pendent Sprinkler

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way-100 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. Air Release Valve 25mm

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Supplying, fixing, testing & commissioning Of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304,sheet with 3 mm dia holes with stainless steel flange.

Providing & fixing of pressure switch in MS, pipe line including connection etc. as required.

(A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting Of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump Of iron body & bronze impeller With stainless steel shaft, confirming to IS : 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply With IP55 class Of protection for enclosure, horiziontal foot mounted type with Class-'F insulation, to IS-325. (D) M.S. fabricated common base plate, guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. Terrace pump 450 lpm, 30 M head

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated Of approved shade after 7 tank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50HzAc Supply with enclosure protection class IP42 as required :

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, as reauired. 4 Zone

Supplying installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed Tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged a)ver plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Supplying, Installing, Testing & Commisioning cost of Main LT Panel for Principal quarter building all complete with all necessary items as per direction of E/I.

Lift Panel : The panel includes 415V, 100A, 3Ph, 35kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character:

Supplying, Installing, Testing & Commisioning cost of Main Distribution Board for SRC cum Library building all complete with all necessary items as per direction of E/I.

Supplying, Installing, Testing & Commisioning cost of Main Distribution Board for 500 Capacity Auditorium building all complete with all necessary items as per direction of E/I.

Supplying, Installing, Testing & Commisioning cost of HVAC Board for 500 Capacity Auditorium building all complete with all necessary items as per direction of E/I.

Supplying, Installing, Testing & Commisioning cost of Main Distribution Board for 700 Bedded Hostel building all complete with all necessary items as per direction of E/I.

Supply, fitting, fixing, commissioning and testing of 500 kVA( level-2) , 11 or 6.6 kV/0.433 kV Deta/Star, vector group DYn11, outdoor mounting, Oil Cooled Type ONAN off circuit Star Rating Transformer with copper wound Transformer and civil foundation work along with required size & length of MS channels as per the norms 1000 kVA outdoor transformer with all accessories as per IS- 1180 of 2014, air filled cable box suitable for 11kV or 6.6 kV 2 run , 3C 120sqmm XLPE Al. armoured cable for 1.1kV, 3Run, 3.5Cx300sqmm XLPE Al. armoured cable as required. ( Make:-ABB/Voltam/ GTB/ Kirloskar / Bharat Bijlee)

Main LT Panel: Supplying, designing, manufacturing, installation, testing, fitting, fixing and commissioning in correct alignment position, effecting proper connection of all incomers and outgoing of LT panel of 14 SWG CRCA Sheet (2mm) steil IP-54 floor mounting cubical type LT Panel suitable for operation on 415V, 50Hz, 3Ph, AC supply and fault level 50kA. Apporexmate size (Shall be given at the time of work order ) with front operated construction including seperate fabrication arrangement for fixing of switchgears and meters.

Outdoor Feeder Panel ( for street light and High mast): Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of outdoor type cubical feeder pillar of suitable size not less than 30 cm and up-to 45 cm deep made out of M.S. sheet 2 mm thick (14 SWG) duly compartmentalized, double door with locking arrangement (IP-54), duly fixed on MS angle iron frame work of suitable size ,earthing with two nos. earth studs, powder coated with rain shed structure etc as reqd. All inter connections shall be made with 2.5, 4 , 6 Sq mm PVC Cu. wire. The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs

Capacitor Panel 150 kVAr

15 Passenger elevator with 5 stops without machine room as per specification - 282 - KONE I MonoSpace R22.1 - 2 (a. price validity 12 months from date of signing order, b. Warranty 12 months from date of handing over)

15 Passenger elevator with 7 stops without machine room as per specification - 282 - KONE I MonoSpace R22.1 - 2 (a. price validity 12 months from date of signing order, b. Warranty 12 months from date of handing over)

Supply & fitting of ShyamJyoti™ LED Based Solar Street Lighting System Luminary : 12W LED Luminary Luminary Housing- Weather Proof Housing Structure- Hot Deep Galvanized Module Pole : Hot Deep Galvanized MS Pole (4.5 Mtr.) Battery Box : Corrosion Resistant Painted Power Coated Metal Battery Box Other : Suitable Cable, Et Battery : 19.8Ah 14.8V Lithium-Ferro Battery of MNRE Approved Module : 75Wp of HBL / Gautam Solar/IEC Equivalent (Cost includes 10% CP & 5 % OHC)

KOXTANS Iron Fixed with Sleeves Volleyball Pole, Height 96 inch KOXTANSR (VOLLEYBALL POLE FIXED) Pole Diameter - 3.5 millimeter Height adjustable - 3.5 meter Number of plate 2

GB INTERNATIONAL Cotton ( 9.5 meter Volleyball Net GB INTERNATIONAL (VLN 39)

baspo Transparent acrylic materia (for competition) Basketball Backstop With Installation baspo (P777) Backboard type For training Provision of adjustable mountings for minor height adjustment - Yes Thickness 25 mm Transparent acrylic material (for competition) - Length 1800 mm Width - 1050 mm

Devraj Mild Steel sheet Double Door with locking arrangment(4) Fire Hose Cabinet, Warranty 1 Year

fireteks Portable Fire Extinguishers as per IS 15683 (2018) High Pressure Extinguisher (Service Pressure >19 bar) Carbon Dioxide Based (as per IS 15222) Class -B fireteks Portable Fire Extinguishers as per IS 15683 (2018) High Pressure Extinguisher (Service Pressure >19 bar) Carbon Dioxide Based (as per IS 15222) Class -B

Ecofire Portable Fire Extinguishers as per IS 15683 (2018) Low Pressure Extinguisher (Service Pressure ≤19 bar) Powder Based (as per IS 4308 ) Class -A a) Capacity 6 kg ISI Marked

PALEX 10 liter GALVANIZED MILD STEEL FIRE BUCKET (Fire suppression hand tools) PALEX (FBSTAND10LTR)

Powder Coated MS 4 Seater Restaurant Table-Table Top 25mm Thick MDF+Membrane Top as per Approved Shade. Over All Size Of Table 1200W x 600D x 750H . Understructure Made Of Prime Quality CRCA 40 x 40 mm Square Metal Pipe Duly Powder Coated. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used. All Metal Shall Be Coated. After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process. Thickness Of Coating (60 – 80) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Restaurant / Cafeteria Chair with frame of Teak Wood and Teak Wood seat-Wooden Frame, Fabric cushioned seat & back. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

FOYER

bansal 3 Seater Public Place Seating Chair of mild steel with arm and backrest WITHOUT CUSHION

Wooden Almirah,

superior Non-Revolving and Non-Tilting chair without Armrest-1)SEAT/BACK ASSEMBLY: The seat and back should be made from 1.0±0.1cm. thk. hot pressed ply and should be true resistant tant commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H) SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) 2)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. 3)UNDERSTRUCTURE ASSEMBLY: The assembly should be a mainframe made of 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube and a welded leg tube made of dia. 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube to the form the complete assembly which should be black powder coated (DFT 40-60 microns).

METHODEX- Powder Coated MS 4 Seater Restaurant Table--Table Top 25mm Thick MDF+Membrane Top as per Approved Shade. Over All Size Of Table 1200W x 600D x 750H . Understructure Made Of Prime Quality CRCA 40 x 40 mm Square Metal Pipe Duly Powder Coated. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used. All Metal Shall Be Coated. After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process. Thickness Of Coating (60 – 80) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Sofa Sets, Number of seats 3 +2

Restaurant / Cafeteria Chair with frame of Teak Wood and Teak Wood seat-Wooden Frame, Fabric cushioned seat & back. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

METHODEX Plastic Moulded Chair With Arms With Cushion Single Piece Plastic Moulded

Revolving Chair With Arm-Medium Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed Supported Back Inner PP Structure . Upholstery PVC Structure Moulded With Prime Quality High Stretch Fabric . PHA ( Gas-Lift ) 105mm ( TDC 171mm & BDC 66 ) . Understructure Base Revolving Pedestal Steel Inserted PP Base With PP Hub Cap . Machanism Torsion Bar Adjustment Can Be Operated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Chair Max Height 980 & min Depth 715 . 470W x 430D Base Seat 70mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 & 430W x 470H Back Seat 50mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 . Base Seat Shell ABS Cover At Underside . Back Seat Shell ABS Cover At Back Side . L - Patta Mild Steel . Beading Finish NA . 440/540 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest PP . Arm Rest Height From Seat 170mm . Height From Seat To Ground 440mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 715mm With Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Almirah Steel shelving cabinets-Overall Size 915W x 485D x 1980H . Office Almirah Made Of Prime Quality CRCA Ms Sheet Panels 0.8mm Thick Powder Coated Finish With Approved Shade . Each Shelve Made Of 0.8mm CRCA MS Sheet Powder Coated . Each Shelve Shall Be Formed Such The Edges Are Bend Two Times At Right Angle. Front Shutter 1mm Thick CRCA Ms Sheet Powder Coated Riveted With Hinges. . No Sharp Edges Of Almirah Ends . All Shelve Rack Divided Into Equal Parts . Leg Shall Be 125 x 90 X 452MM 2 Nos With 1mm Thick CRCA Metal Sheet Powder Coated . Door Die Cast Chrome Plated Handles Fitted With Washer & Double Nut . Handles Ring Made Of PVC Cap . Locking Bright Bar 10mm Dia . Almirah All Metallic Panels Screw With Nut & Bolt . Bottom Shelve 125mm High Up To Ground . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating almFor Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for STORAG FURNITURE range for ergonomic design.

FURNHARDT THREE SEATER Class Room Desking / Seating THREE SEATER 1500W x 915D x 750H Table Top 18mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish As Per Approved Laminate Shade . Thick CRCA Ms Sheet Welded With Round Pipe Leg . 200H 18mm Thick PLPB Modesty Panel . Understructure CRCA Round Metal Pipe 38mm Dia With 1.6mm Thick All Side Welded With Vertically & Horizontally Metal Pipe powder coated . School Desk Provided with Both Side Bag Hooks. All Joints Screw With Nut & Bolt . All Frames Round Pipe Closed With Pvc Caps. Legs Of The Table Hard Rubber Shoes. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used. All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for EDUCATIONAL FURNITURE range for ergonomic design.

METHODEX - POWDER COATED MS 6SEATER RESTURENT TABLE-Table Top Designed With 25 mm PLPB . Top Size 1800W x 900D. Understructure Leg Designed With combination of 50x50 and 40X40mm Square CRCA 16 Guage Thick Duly powder Coated . Legs Of The Table Hard Rubber Shoes. Wooden Panels Prime Quality Board With ISI Marked . MIG Welding All - Around The Weld Joints Using Inert Gas (Argon.) The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

superior Non-Revolving and Non-Tilting chair without Armrest-1)SEAT/BACK ASSEMBLY: The seat and back should be made from 1.0±0.1cm. thk. hot pressed ply and should be true resistant tant commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H) SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) 2)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. 3)UNDERSTRUCTURE ASSEMBLY: The assembly should be a mainframe made of 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube and a welded leg tube made of dia. 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube to the form the complete assembly which should be black powder coated (DFT 40-60 microns).

Revolving Chair - NYLA - HB H : 1250 ±10 W : 720 ±10D : 720 ±10 High Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat & Back Plywood Made Of 15mm Hot Pressed Supported . Upholstery Structure Moulded With Prime Quality Leatherite . PHA ( Gas- Lift ) 85mm (TDC 152mm & BDC 67) . Understructure Base Revolving Pedestal Chorme Plated Steel Base With PP Hub Cap . Machanism Tilt Adjustment Can Be Operated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Chair Max Height 1250 & min Depth 730 . 500 x 490 Base Seat100mm Thick Moulded With PU Foam , D -45 kg/m3 , H- 18 & 520W x 690H Back Seat 100mm Thick Moulded With PU Foam , D -45 kg/m3 , H-18 . 470/580 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest Height From Seat 200mm . Arm Rest PU Moulded . Height From Seat To Ground 500mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 720mm With Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Methodex - Executive Table with Both side pedestal unit- LEGEND - 04 -Table Top 25 mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade.Understructure 1320W X 655D X 725H Made Of Prime Quality 1.2 mm Thick CRCA 25x25mm Square Metal Pipe. Understructure CRCA Square Metal Pipe 25X25mm With 1 mm Thick Four Side Welded With Vertically Metal Pipe & 7 tank treatment with minimum 45-50 micron powder coating, . Metal 1st Storage (3D ) & Other 2nd Storage ( 1S ) Made Of Prime Quality 0.8mm Thick CRCA Metal Sheet Tank Treatment With Minimum 45 - 50 Micron Powder Coating With Locking Facility . All Frames Rectangular Pipe & Square Metal Pipe Closed With Pvc Caps . Legs Of The Table Hard Rubber Shoes . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² .

METHODEX Almirah Steel shelving cabinets- Overall Size 915W x 485D x 1980H . Office Almirah Made Of Prime Quality CRCA Ms Sheet Panels 0.8mm Thick Powder Coated Finish With Approved Shade . Each Shelve Made Of 0.8mm CRCA MS Sheet Powder Coated . Each Shelve Shall Be Formed Such The Edges Are Bend Two Times At Right Angle. Front Shutter 1mm Thick CRCA Ms Sheet Powder Coated Riveted With Hinges. . No Sharp Edges Of Almirah Ends . All Shelve Rack Divided Into Equal Parts . Leg Shall Be 125 x 90 X 452MM 2 Nos With 1mm Thick CRCA Metal Sheet Powder Coated . Door Die Cast Chrome Plated Handles Fitted With Washer & Double Nut . Handles Ring Made Of PVC Cap . Locking Bright Bar 10mm Dia . Almirah All Metallic Panels Screw With Nut & Bolt . Bottom Shelve 125mm High Up To Ground . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for STORAG FURNITURE range for ergonomic design.

METHODEX Sofa Sets, Number of seats 3+2- 3 SEATER Sofa Made Of Good Quality Products Of MSPL Standard Models . 12mm Ply Used Made Of Back & Base . Upholstery Made Of Prime Quality Rexine Black . Base Seat Moulded With Foam , ( 90mm + 21mm ) Thick , D - 28KG/m3 . Back Seat Moulded With Foam , 45 Thick , D - 28KG/m3 . Arm rest Moulded With Foam , 45 Thick , D - 28KG/m3 . Back Inserted Foam , 21 Thick , D - 28KG/m3 . Ends Of The BJ 3S Sofa Structure PVC Caps . Sofa L Brakets & Base Frame Made Of Prime Quality MS . Fastners Nut Bolt 4Nos . Size M8 x 38mm . Sofa Structure Shall have MS Spring Base . Understructure Made of Base Frame 20 x 20 Square SS Pipe 1.2mm Thick . Support Frame Made Of 12mm Dia Round SS Pipe 1.2mm Thick . Side Frame Made Of 25mm Dia Round SS Pipe 1.6mm Thick . Pinewood 25W x 25mm Thick Seat Height From Bottom To Base 458mm .Back Height From Base Seat To Top 356mm . Hand Rest Width 150mm . All SS Pipes Shall Be Welded Properly Strongly and conformity with regulations . Sofa Structure Stailness Steel Pipe Shall Be Abrasive Polished External Finished . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. 2 SEATER -Sofa Made Of Good Quality Products Of MSPL Standard Models . 12mm Ply Used Made Of Back & Base . Upholstery Made Of Prime Quality Rexine Black . Base Seat Moulded With Foam , ( 90mm + 21mm ) Thick , D - 28KG/m3 . Back Seat Moulded With Foam , 45 Thick , D - 28KG/m3 . Arm rest Moulded With Foam , 45 Thick , D - 28KG/m3 . Back Inserted Foam , 21 Thick , D - 28KG/m3 . Ends Of The BJ 3S Sofa Structure PVC Caps . Sofa L Brakets & Base Frame Made Of Prime Quality MS . Fastners Nut Bolt 4Nos . Size M8 x 38mm . Sofa Structure Shall have MS Spring Base . Understructure Made of Base Frame 20 x 20 Square SS Pipe 1.2mm Thick . Support Frame Made Of 12mm Dia Round SS Pipe 1.2mm Thick . Side Frame Made Of 25mm Dia Round SS Pipe 1.6mm Thick . Pinewood 25W x 25mm Thick . Seat Height From Bottom To Base 458mm . Back Height From Base Seat To Top 356mm . Hand Rest Width 150mm . All SS Pipes Shall Be Welded Properly Strongly and conformity with regulations . Sofa Structure Stailness Steel Pipe Shall Be Abrasive Polished External Finished . The product should bear IGBC Green Pro certificate for product categFory. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Unbranded Plastic Moulded Chair With Arms With Cushion Single Piece Plastic Moulded

Wooden Book Case made up of Flat single layer MDF board of grade SBG II of IS 12406/Latest and 2 shelves

Unbranded Rectangular CENTRE TABLE with Flat glass Top of 1219mmX711mm- Specification:- Centre Table MS LIVON 2448, Made up of engineering wood. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design.

METHODEX - Powder Coated MS 6 Seater Restaurant Table-Table Top Designed With 25 mm PLPB . Top Size 1800W x 900D. Understructure Leg Designed With combination of 50x50 and 40X40mm Square CRCA 16 Guage Thick Duly powder Coated . Legs Of The Table Hard Rubber Shoes. Wooden Panels Prime Quality Board With ISI Marked . MIG Welding All - Around The Weld Joints Using Inert Gas (Argon.) The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

METHODEX- furnitures Computer Table consists of Computer table with key board drawer and table top- Computer Table Top 18mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade. Top Supported Understructure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board. Top Size 800W X 450D. 18mm Thick PLPB Wooden Shelve Fix In Table under Table Top . Right Hand Side Provided L Shape Shelve Use For CPU & UPS . Shelve Used Sliding Telescopic Channel With All Fittings. Table , Shelve & Sides Panels Flat Edge Duly Sealed With Pvc Beading . 50mm High Wooden Panel Skirting Provided in Computer Table . 7mm High Pvc Bofurs Screw With Gable . All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment . Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Unbranded Portrait/ Landscape Not applicable Fabric Pin Up Notice Boards-Surface:4x3 Magnetic white board marker surface. Inner Core: Hard smooth particleboard. Back: Laminated sheet. Frame: Anodized aluminum. Corner: ABS Plastic, Mounting Hardware

AUDITARIUM CHAIR

Table 900W x 450D, 18mm thick PLPB top, 40x40x1.2mm CRCA powder coated frame. Table Top 18 mm Thick PLPB Board as Per Approved Laminate Shade. Understructure Made Of Prime Quality CRCA 40 x 40 x 1.2mm Square Metal Pipe. Table Top Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Understructure CRCA Metal Pipe 25X25mm With 1.2mm Thick Four Side Welded With Vertically Metal Pipe. Table Understructure 850W X 550D In 25 X 25 Square Pipe With 1.2mm Thick. Height Of The Understructure 700mm. Legs Of The Table Hard Rubber Shoes. All Metal Shall Be Powder Coated After Being Treated With at Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . Metal Storage ( 1D + 1S ) Made Of Prime Quality 22guage CRCA Metal Sheet Tank Treatment With Minimum 45 - 50 Micron Powder Coating. Legs Of The Table Hard Rubber Shoes. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design

METHODEX- Table Top 25mm Thick PLPB Board as Per Approved Laminate Shade. Total Height Of The Library Table 770mm. Metal Structure Width 1150mm & 850mm Depth. Understructure Made Of Prime Quality CRCA 25x25mm Square Metal Pipe. Perforated Modesty Panel 0.8mm Thick CRCA Metal Sheet with 25 mm square pipe boundry. Upper Wooden Panels 18mm Thick PLPB Board Used For Book Shelve. Table Top & Upper Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Upper Wooden partition/storage size : 300 mm H x 300 mm D. Understructure CRCA Metal Pipe 25X25mm With 1.2mm Thick Four Side Welded With Vertically Metal Pipe. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. All Metal Shall Be Powder Coated After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust. Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Coating thickness must be between 60 to 80µ. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for EDUCATIONAL FURNITURE range for ergonomic design.

METHODEX -Non-Revolving and Non Tilting chair with Armrest-Metal Chrome frame, Leatherete seat & back. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

- MODULAR TABLE L X D & H 1500 millimeter X 900 millimeter 750 millimeter

METHODEX - Revolving Chair With Arm Centre pivot mechanism- Medium Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed Supported Back Inner PP Structure . Upholstery PVC Structure Moulded With Prime Quality High Stretch Fabric . PHA ( Gas-Lift ) 105mm ( TDC 171mm & BDC 66 ) . Understructure Base Revolving Pedestal Steel Inserted PP Base With PP Hub Cap . Machanism Torsion Bar Adjustment Can Be Operated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Chair Max Height 980 & min Depth 715 . 470W x 430D Base Seat 70mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 & 430W x 470H Back Seat 50mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 . Base Seat Shell ABS Cover At Underside . Back Seat Shell ABS Cover At Back Side . L - Patta Mild Steel . Beading Finish NA . 440/540 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest PP . Arm Rest Height From Seat 170mm . Height From Seat To Ground 440mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 715mm With Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

METHODEX - Modular Work Stations with Four Seater Plus Shape Cluster with Curvilenear Top-Top to be made up of ISI mark 25 mm thick pre laminated Particle Board finished with 2 mm thick PVC edging applied on Through Feed Edging Machine UNDERSTRUCTURE- The under structure to be made up of CRCA, C shaped legs shall be of pipe of size 50x50 mm and 40x40 cross member for support and stability finished with powder coating. SCREEN- Divider screen of size1500x300mm to be fixed above the table top level. The fabric screen to be in 30/32mm thickness having aluminium sections all 4 sides. Race way – CRCA raceway for carrying electrical and data wiring are provided below the table top with provision for fixing switches. Each cluster to be provided with wire riser from floor to wire raceway and aluminium access flap on worktop for easy access to electrical switches . PEDESTAL, KEY BOARD AND CPU TROLLEY ARE NOT CONSIDERED IF REQUIRE COST WILL BE EXTRA. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for LAB FURNITURE range for ergonomic design.

METHODEX -Almirah Steel shelving cabinets- Overall Size 915W x 485D x 1980H . Office Almirah Made Of Prime Quality CRCA Ms Sheet Panels 0.8mm Thick Powder Coated Finish With Approved Shade . Each Shelve Made Of 0.8mm CRCA MS Sheet Powder Coated . Each Shelve Shall Be Formed Such The Edges Are Bend Two Times At Right Angle. Front Shutter 1mm Thick CRCA Ms Sheet Powder Coated Riveted With Hinges. . No Sharp Edges Of Almirah Ends . All Shelve Rack Divided Into Equal Parts . Leg Shall Be 125 x 90 X 452MM 2 Nos With 1mm Thick CRCA Metal Sheet Powder Coated . Door Die Cast Chrome Plated Handles Fitted With Washer & Double Nut . Handles Ring Made Of PVC Cap . Locking Bright Bar 10mm Dia . Almirah All Metallic Panels Screw With Nut & Bolt . Bottom Shelve 125mm High Up To Ground . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for STORAG FURNITURE range for ergonomic design.

BHUMITI Wooden Almirah, Height 2100

METHODEX - Non-Revolving and Non Tilting chair with Armrest-Metal Chrome frame, Leatherete seat & back. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

LIBRARY TABLE SIZE - 1200W x 900D x 770H , Table Top 25mm Thick PLPB Board as Per Approved Laminate Shade. Total Height Of The Library Table 770mm. Metal Structure Width 1150mm & 850mm Depth. Understructure Made Of Prime Quality CRCA 25x25mm Square Metal Pipe. Perforated Modesty Panel 0.8mm Thick CRCA Metal Sheet with 25 mm square pipe boundry. Upper Wooden Panels 18mm Thick PLPB Board Used For Book Shelve. Table Top & Upper Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Upper Wooden partition/storage size : 300 mm H x 300 mm D. Understructure CRCA Metal Pipe 25X25mm With 1.2mm Thick Four Side Welded With Vertically Metal Pipe. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. All Metal Shall Be Powder Coated After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust. Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Coating thickness must be between 60 to 80µ. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for EDUCATIONAL FURNITURE range for ergonomic design.

METHODEX - Non-Revolving and Non Tilting chair with Armrest- Metal Chrome frame, Leatherete seat & back. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

MODULAR TABLE L X D & H 1500 millimeter X 900 millimeter 750 millimeter

Revolving Chair With Arm Centre pivot mechanism-Medium Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed Supported Back Inner PP Structure . Upholstery PVC Structure Moulded With Prime Quality High Stretch Fabric . PHA ( Gas-Lift ) 105mm ( TDC 171mm & BDC 66 ) . Understructure Base Revolving Pedestal Steel Inserted PP Base With PP Hub Cap . Machanism Torsion Bar Adjustment Can Be Operated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Chair Max Height 980 & min Depth 715 . 470W x 430D Base Seat 70mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 & 430W x 470H Back Seat 50mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 . Base Seat Shell ABS Cover At Underside . Back Seat Shell ABS Cover At Back Side . L - Patta Mild Steel . Beading Finish NA . 440/540 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest PP . Arm Rest Height From Seat 170mm . Height From Seat To Ground 440mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 715mm With Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

METHODEX - Almirah Steel shelving cabinets-Overall Size 915W x 485D x 1980H . Office Almirah Made Of Prime Quality CRCA Ms Sheet Panels 0.8mm Thick Powder Coated Finish With Approved Shade . Each Shelve Made Of 0.8mm CRCA MS Sheet Powder Coated . Each Shelve Shall Be Formed Such The Edges Are Bend Two Times At Right Angle. Front Shutter 1mm Thick CRCA Ms Sheet Powder Coated Riveted With Hinges. . No Sharp Edges Of Almirah Ends . All Shelve Rack Divided Into Equal Parts . Leg Shall Be 125 x 90 X 452MM 2 Nos With 1mm Thick CRCA Metal Sheet Powder Coated . Door Die Cast Chrome Plated Handles Fitted With Washer & Double Nut . Handles Ring Made Of PVC Cap . Locking Bright Bar 10mm Dia . Almirah All Metallic Panels Screw With Nut & Bolt . Bottom Shelve 125mm High Up To Ground . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for STORAG FURNITURE range for ergonomic design.

SYSTEMS MODULAR TABLE L X D & H 1500 millimeter X 900 millimeter 750 millimeter

Non-Revolving and Non-Tilting chair with Armrest-1)SEAT/BACK ASSEMBLY: The seat and back should be made from 1.0±0.1cm. thk. hot pressed ply and should be true resistant tant commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H) SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) 2)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. 3)UNDERSTRUCTURE ASSEMBLY: The assembly should be a mainframe made of 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube and a welded leg tube made of dia. 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube to the form the complete assembly which should be black powder coated (DFT 40-60 microns).

Unbranded Steel Bookcase having 4 Doors and three way bolting device controlled by lock

OFFICE TABLE CUM LIBRARY READING TABLE SIZE- Table Top 25mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade.Understructure Made Of Prime Quality CRCA 25x25mm Square Metal Pipe. Metal Structure Width 850mm & 550mm Depth. Understructure CRCA Metal Pipe 25X25mm With 1.2mm Thick Four Side Welded With Vertically Metal Pipe. Legs Of The Table having Hard Rubber Shoes. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. All Metal Shall Be powder Coated. After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt UsingSpecial Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Thickness Of Coating (60 – 80) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for hostel FURNITURE range for ergonomic design.

METHODEX -Non-Revolving and Non Tilting chair with Armrest-Metal Chrome frame, Leatherete seat & back. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

METHODEX , Almirah Steel shelving cabinets- Overall Size 915W x 485D x 1980H . Office Almirah Made Of Prime Quality CRCA Ms Sheet Panels 0.8mm Thick Powder Coated Finish With Approved Shade . Each Shelve Made Of 0.8mm CRCA MS Sheet Powder Coated . Each Shelve Shall Be Formed Such The Edges Are Bend Two Times At Right Angle. Front Shutter 1mm Thick CRCA Ms Sheet Powder Coated Riveted With Hinges. . No Sharp Edges Of Almirah Ends . All Shelve Rack Divided Into Equal Parts . Leg Shall Be 125 x 90 X 452MM 2 Nos With 1mm Thick CRCA Metal Sheet Powder Coated . Door Die Cast Chrome Plated Handles Fitted With Washer & Double Nut . Handles Ring Made Of PVC Cap . Locking Bright Bar 10mm Dia . Almirah All Metallic Panels Screw With Nut & Bolt . Bottom Shelve 125mm High Up To Ground . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for STORAG FURNITURE range for ergonomic design.

BHUMITI Wooden Almirah, Height 2100

Wooden Book Case made up of Flat single layer MDF board of grade SBG II of IS 12406/Latest and 2 shelves

METHODEX - THREE SEATER TUBULAR STEEL SOFA SET -BJ Made Of Good Quality Products Of MSPL Standard Models . 12mm Ply Used Made Of Back & Base . Upholstery Made Of Prime Quality Rexine Black . Base Seat Moulded With Foam , ( 90mm + 21mm ) Thick , D - 28KG/m3 . Back Seat Moulded With Foam , 45 Thick , D - 28KG/m3 . Arm rest Moulded With Foam , 45 Thick , D - 28KG/m3 . Back Inserted Foam , 21 Thick , D - 28KG/m3 . Ends Of The BJ 3S Sofa Structure PVC Caps . Sofa L Brakets & Base Frame Made Of Prime Quality MS . Fastners Nut Bolt 4Nos . Size M8 x 38mm . BJ Sofa Structure Shall have MS Spring Base . Understructure Made of Base Frame 20 x 20 Square SS Pipe 1.2mm Thick . Support Frame Made Of 12mm Dia Round SS Pipe 1.2mm Thick . Side Frame Made Of 25mm Dia Round SS Pipe 1.6mm Thick . Pinewood 25W x 25mm Thick . Seat Height From Bottom To Base 458mm . Back Height From Base Seat To Top 356mm . Seat 585 Depth . Hand Rest Width 150mm . All SS Pipes Shall Be Welded Properly Strongly and conformity with regulations . BJ Sofa Structure Stailness Steel Pipe Shall Be Abrasive Polished External Finished . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

STEEL CHAIR SINGLE SEATER -1)SEAT/BACK ASSEMBLY: The seat and back should be made from 1.0±0.1cm. thk. hot pressed ply and should be true resistant tant commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H) SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) 2)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. 3)UNDERSTRUCTURE ASSEMBLY: The assembly should be a mainframe made of 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube and a welded leg tube made of dia. 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube to the form the complete assembly which should be black powder coated (DFT 40-60 microns).

Non-Revolving and Non Tilting chair with Armrest-Metal Chrome frame, Leatherete seat & back. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Dual Seating 36 Mm Thick Flat Single Layer MDF Board Of Grade SBG-II Of IS:12406/Latest Modular Extendable Conference Table

methodex -furnitures Computer Table consists of Computer table with key board drawer and table top-Computer Table Top 18mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade. Top Supported Understructure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board. Top Size 800W X 450D. 18mm Thick PLPB Wooden Shelve Fix In Table under Table Top . Right Hand Side Provided L Shape Shelve Use For CPU & UPS . Shelve Used Sliding Telescopic Channel With All Fittings. Table , Shelve & Sides Panels Flat Edge Duly Sealed With Pvc Beading . 50mm High Wooden Panel Skirting Provided in Computer Table . 7mm High Pvc Bofurs Screw With Gable . All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment . Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Revolving Chair With Arm Centre pivot mechanism- Medium Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed Supported Back Inner PP Structure . Upholstery PVC Structure Moulded With Prime Quality High Stretch Fabric . PHA ( Gas-Lift ) 105mm ( TDC 171mm & BDC 66 ) . Understructure Base Revolving Pedestal Steel Inserted PP Base With PP Hub Cap . Machanism Torsion Bar Adjustment Can Be Operated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Chair Max Height 980 & min Depth 715 . 470W x 430D Base Seat 70mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 & 430W x 470H Back Seat 50mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 . Base Seat Shell ABS Cover At Underside . Back Seat Shell ABS Cover At Back Side . L - Patta Mild Steel . Beading Finish NA . 440/540 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest PP . Arm Rest Height From Seat 170mm . Height From Seat To Ground 440mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 715mm With Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Newspaper Reading Stand -News Paper Stand Made out of 25 mm x 25mm CRCA pipe U/S with Hut Style Design For Keeping Daily News Paper and steel strips are Provided for locking News Paper Height Of Stand is 1100 mm ( can be Done As Per Requirement). Base pipe used from 50 x 25 mm. All Steel Parts Are Duly Powder Coated With 40 to 50 Microns.This Versatile Newspaper Reading rack is Meant For Two News Papers One on Each Side And Two Persons Can Read The Newspaper At Convenient Standing Height . All Frames Square Pipe Closed With Pvc Caps . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for EDUCATIONAL FURNITURE range for ergonomic design.

Wooden Podiumdesign Gable end and modesty panel and top material Teak wood- Top Designed With 18 mm Thick Commercial Board Affixed With 0.6mm Mica . Support Structure Of Podium Designed With Solid Wood . Modesty Panel Having Affixed With Veneer Pressed With Polish . Modesty Panel Design With Solid Wood And Beading . All Edge And Structure Finished With Proper Color Combination Matched To Laminated Shade. Front & Side Designed By 25mm Commercial Board With 3mm Shisham Vineer Duly Wallnut Polish Finish . Table Made By Joint Of Two Wooden Parts . Legs Of The Podium Hard Rubber Shoes. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Portrait/ Landscape Not applicable Fabric Pin Up Notice Boards-Surface: Magnetic White Board 3'x4'-Magnetic white board marker surface. Inner Core: Hard smooth particleboard. Back: Laminated sheet. Frame: Anodized aluminum. Corner: ABS Plastic, Mounting Hardware

Auditorium Chair Made Of Good Quality Products Of MSPL Standard Models . Upholstery Made Of Fire Retardant Fabric Passed With P.U Foam . Black Powder Coated Scissor Machnism Synchronous Movement Of Back And Seat With Sliding Movement Of Back & Seat With Sliding Movement Of Seat Auto Tip - Up . 440W x 450D Base Seat 150mm Thick CRCA Round Pipe 2mm Thick Pipe Frame Moulded With PU Foam (D-50KG/m3 , H-20) Having Ply At The Underside & Covered With PP . 450W x 700H Back Seat 130mm Thick CRCA Round Pipe 2mm Thick Pipe Frame Moulded With PU Foam (D-50KG/m3 , H-20) . 125W x 395D x 555H 1.6mm HRCA Sheet Side Panel Metallic Strucuture Made Of HRCA Sheet Fastened With Machanism . 440/620 Arm Rest Handles PU / Cup Holder . The Metal Part Scratch Resisitant . Foot Made Of HRCA Sheet Powder Coated . Understructure Fixed Type Back & Base Structure Having Grouted Side Panel , Fastened With Machanism . 38W x 78D 1.6mm Thick Grouting Support Pipe . Writing Pad Made Of Solid Wood . Height From Seat To Ground 485mm . Arm Rest Height From Seat 230mm . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . Thickness Of Coating (40 – 50) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for AUDITORIUM FURNITURE range for ergonomic design.

PODIUM-Top Designed With 18 mm Thick Commercial Board Affixed With 0.6mm Mica . Support Structure Of Podium Designed With Solid Wood . Modesty Panel Having Affixed With Veneer Pressed With Polish . Modesty Panel Design With Solid Wood And Beading . All Edge And Structure Finished With Proper Color Combination Matched To Laminated Shade. Front & Side Designed By 25mm Commercial Board With 3mm Shisham Vineer Duly Wallnut Polish Finish . Table Made By Joint Of Two Wooden Parts . Legs Of The Podium Hard Rubber Shoes. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Sofa Sets, Number of seats 3+2- 3 seater -Sofa Made Of Good Quality Products Of MSPL Standard Models . 12mm Ply Used Made Of Back & Base . Upholstery Made Of Prime Quality Rexine Black . Base Seat Moulded With Foam , ( 90mm + 21mm ) Thick , D - 28KG/m3 . Back Seat Moulded With Foam , 45 Thick , D - 28KG/m3 . Arm rest Moulded With Foam , 45 Thick , D - 28KG/m3 . Back Inserted Foam , 21 Thick , D - 28KG/m3 . Ends Of The BJ 3S Sofa Structure PVC Caps . Sofa L Brakets & Base Frame Made Of Prime Quality MS . Fastners Nut Bolt 4Nos . Size M8 x 38mm . Sofa Structure Shall have MS Spring Base . Understructure Made of Base Frame 20 x 20 Square SS Pipe 1.2mm Thick . Support Frame Made Of 12mm Dia Round SS Pipe 1.2mm Thick . Side Frame Made Of 25mm Dia Round SS Pipe 1.6mm Thick . Pinewood 25W x 25mm Thick . Seat Height From Bottom To Base 458mm .Back Height From Base Seat To Top 356mm . Hand Rest Width 150mm . All SS Pipes Shall Be Welded Properly Strongly and conformity with regulations . Sofa Structure Stailness Steel Pipe Shall Be Abrasive Polished External Finished . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. Sofa Made Of Good Quality Products Of MSPL Standard Models . 12mm Ply Used Made Of Back & Base . Upholstery Made Of Prime Quality Rexine Black . Base Seat Moulded With Foam , ( 90mm + 21mm ) Thick , D - 28KG/m3 . Back Seat Moulded With Foam , 45 Thick , D - 28KG/m3 . Arm rest Moulded With Foam , 45 Thick , D - 28KG/m3 . Back Inserted Foam , 21 Thick , D - 28KG/m3 . Ends Of The BJ 3S Sofa Structure PVC Caps . Sofa L Brakets & Base Frame Made Of Prime Quality MS . Fastners Nut Bolt 4Nos . Size M8 x 38mm . Sofa Structure Shall have MS Spring Base . Understructure Made of Base Frame 20 x 20 Square SS Pipe 1.2mm Thick . Support Frame Made Of 12mm Dia Round SS Pipe 1.2mm Thick . Side Frame Made Of 25mm Dia Round SS Pipe 1.6mm Thick . Pinewood 25W x 25mm Thick . Seat Height From Bottom To Base 458mm . Back Height From Base Seat To Top 356mm . Hand Rest Width 150mm . All SS Pipes Shall Be Welded Properly Strongly and conformity with regulations . Sofa Structure Stailness Steel Pipe Shall Be Abrasive Polished External Finished . The product should bear IGBC Green Pro certificate for product categFory. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Executive Table with Both side pedestal unit-Table Top 25 mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade.Understructure 1320W X 655D X 725H Made Of Prime Quality 1.2 mm Thick CRCA 25x25mm Square Metal Pipe. Understructure CRCA Square Metal Pipe 25X25mm With 1 mm Thick Four Side Welded With Vertically Metal Pipe & 7 tank treatment with minimum 45-50 micron powder coating, . Metal 1st Storage (3D) & Other 2nd Storage ( 1S ) Made Of Prime Quality 0.8mm Thick CRCA Metal Sheet Tank Treatment With Minimum 45 - 50 Micron Powder Coating With Locking Facility . All Frames Rectangular Pipe & Square Metal Pipe Closed With Pvc Caps . Legs Of The Table Hard Rubber Shoes . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special ThermalControl Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² .

Offer for Supply & Installation of DUCTED SYSTEM

SITC of 220"(16:9) Tubular Motorized screen with LVC, I.R Remote & Matte White Fiber Glass Fabric Matt White along with all supporting accessories. Make:- Grandview/Da-lite/Drapper/Suvira

SITC of Projection system with Projector & Lens : [Projection size],Aspect ratio: 16:10(WUXGA),Diagonal: 5.660 m / 222.85 in / 18.57 ft,Height: 3.000 m / 118.11 in / 9.84 ft Width: 4.800 m / 188.98 in / 15.75 ft,[Projection distance] L: 4.785–6.438 m / 188.38–253.45 in / 15.70–21.12 ft,[Optical shift range],VS1: 1.500 m / 59.06 in / 4.92 ft VS2: 0.480 m / 18.90 in / 1.57 ft,HS1: 1.344 m / 52.91 in / 4.41 ft,HS2: 0.480 m / 18.90 in / 1.57 ft,[Brightness], Projector output: 9,400 lm,Screen illuminance: 653 lx and should also comply that it is having DLP™ chip Panel size-17.0 mm (0.67 in) diagonal (16:10 aspect ratio),Display method-DLP™ chip × 1, DLP™ system,Pixels-2,304,000 (1920 × 1200) × 1, total of 1,024,000 pixels,Lens-Powered zoom/focus lenses,Light Source-Laser Diode Laser class 1,Illumination of Life Set- Should be Vary depending on operation mode setting. 20,000 hours at half luminance NORMAL /QUIET1/ QUIET2)/24,000 hours at half luminance (ECO)* Temperature: 30°C (86°F), Altitude 700m (2,297 ft),Dynamic Contrast3,Under conditions of 0.15 mg/m3 of particulate matter Lumen maintenance rate(rough estimate) : 5000 hours 80% / 10000 hours 70%,43,800 hours at constant luminance (LONG LIFE1),61,320 hours at constant ,luminance (LONG LIFE2),87,600 hours at constant luminance (LONG LIFE3). Preffered Make- Panasonic, Hitachi,Sony

SITC of Celing Mount Kit for Projector with accessories; Make Custom

SITC of 4K Transmitter HDMI bidirectional RS232 and IR over high definition base1, Make-Prefferred Make-Crestron/Lightware/Key-Digital/Kramer

SITC of HD Scaling Auto-Switcher & HDMI® over CATx Extender with Wall Plate Transmitter and surface mount receiver Black in colour to be installed at Podium(Transmitter) and Control Room(Receiver); Prefferred Make- Crestron/Lightware/Key-Digital/Kramer

SITC of High Power 2-Way Flyable Loudspeaker with 1 x 15” LF & Rotatable Horn, Coverage Pattern: 120° x 60° or better, rotatable waveguide, Frequency Response (±3 dB): 40 Hz – 18k Hz or better, Maximum SPL: 130 dB Peak or better, Sensitivity: 96 dB SPL or better, Power: 600 W or better; Should be Bi- amp/passive switchable, High Frequency Driver: 1.5" or better.

Installation accessories for mounting the above FOH arrayable speaker, i.e. eye bolt, rope wire and claimp etc as per site condition.

SITC of High Power Subwoofer 18"dual subwoofer; Frequency Range: 28 Hz – 1 kHz; Power Rating :9600W Peak; Maximum SPL 30 to 500HZ =142 dB Peak; Sensitivity 30 to 500HZ =102 dB Peak; Nominal Impedance: 4 ohms; Input Modes: Drivers Parallel / Drivers Discrete

SITC of 12" Two-Way Floor Monitor; Frequency Range (-10 dB) 55 Hz – 20 kHz; Frequency Response (+3 dB) 68 Hz – 19 kHz; Coverage Pattern 90° x 50°; Maximum SPL-120 db; System Sensitivity (1w @ 1m): 95 dB SPL; Nominal Impedance: 8 ohms; Power Handling (Continuous/Program)- 300 W / 600 W

SITC of Advanced Feedback Suppression; Stereo or Dual Independent Channel Processing; 2In 2 Out; Max input line level = +20 dBu; A/D Conversion =24-bit; THD+Noise 0.003%; Should have Wizard Setup Function; Should have Full LCD Display; 24 Programmable Filters per Channel; Live and Fixed Filter Modes; 24 LED per Channel Filter Metering; Input Impedance: Balanced 50kΩ, Unbalanced 25kΩ; Frequency Response: 20Hz – 20kHz, +/- 0.5dB; Crosstalk input to output: >80 dB

SITC of Four Channel Digital Power Amplifier, 600W@4 Ohms, On-board Digital Signal Processor and includes these integrated features: Input Router , Input Delay – Up to 1000ms , Input Parametric EQ – 8 band , Crossover , Output Parametric EQ – 8 band ,Output Delay – Up to 100ms , Limiter, "Should be controllable, configurable and monitorabe through standard TCP/IQ network."; "Each output channel should be capable of providing either 70V or 100V for high impedance applications."; Completely configure the amplifier using an intuitive front-panel interface. Should have GPIO/AUX Port to Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined; Digital Signal Processing :96kHz, 32-bit floating point; Voltage Gain : 34dB; Frequency Response (8Ω, 20Hz - 20kHz): +/-0.25dB; THD : 0.35%; SNR: >104dB; Damping Factor : >1000; Crosstalk: >80dB; 4x600 W at 4 Ohm ,8 Ohm 70V , and 100 V

SITC of Volume Controller, Should be Compatible with supplied DSP, Should support PoE (Power Over Ethernet); 8 Programmable Buttons (Multicolored) Capable to trigger any DSP logic; Multicolored 2 Programmable 64x128 Pixel LCDs; Sleep Function; Security: Remote Lock/Unlock and Local Unlock via PIN Entry; Should have knob and capable to control 8 zones separate

SITC of Analog Audio Mixer with 16 mono microphone channels , 4 stereo returns , 4-bus architecture, with sub-group routable to mix , Built-in 24 bit digital effects processor , 32 FX settings , Tap Tempo , 3 FX parameter adjust rotaries , User FX settings store function , Direct outputs for multi-track recording individually switch-able for pre-post-fade operation ,Inserts on all mono channels , Inserts on stereo mix output , Classic Soundcraft 3-band EQ with swept mid-band , Stereo 18dB/octave 100Hz high-pass filter , Dual global +48V phantom power split channels 1-8 and 9-16 , Channel Mute control , 10-segment tri-coloured metering , Two sub-group outputs , Separate mono sum output , Integral universal power supply

SITC of Wired Dynamic Instrument Microphone; Cardioid Dynamic Instrument Microphone; Audio frequency bandwidth =40 - 20000 Hz; Sensitivity at 1000 Hz 2.5 mV/Pa (–52 dBV re 1 V/Pa; Max. SPL for 1 % THD = 47 dB SPL

SITC of Wireless Handheld Microphone System; Wireless Microphone system with MHZ carrier frequency band, Up to 16 pre-programmed frequencies within the same frequency band; Audio bandwidth 35 - 20,000 Hz; THD at 1 kHz: <0.3% (Receiver); Signal-to-noise: 120 dB(A) ( Receiver); Wideband FM Modulation; Up to 48 Simultaneous channels; Upto 14 hours operation with one single AA battery or better; Pilot Tone transmission to know the transmitter battery status; Receiver should have microphone level and line level output; Transmitter should have display to show the battery and LED to show the Muted /Unmuted status; Sensitivity 6.3 dB V / -100 dBm; Should have Microprocessor-controlled diversity; T.H.D. 0.7 % (Transmitter); Infrared programmable; RF output power: 10 or 50 mW

19" 26 U , 800mm X 600mm Equipment rack with complete fan, tray, rack rails, etc. (Approved Makes: Standard as per Direction of EIC)

SITC of Patch box with 08 connector options for mic & stage monitor

2.5 Sq. mm Speaker Cable, 100 M roll (Approved Makes: Bandridge, Klotz, Belden, Krystal)

23/0.2 mm Mic Cable, 100 M roll (Approved Makes: Bandridge, Klotz, Belden, Krystal)

Control Cable STP Cat 5e (Approved Makes : D-Link, 3C3, Belden, MX or equivalent)

SITC of Connectors & Patch Cables. (Approved Makes : Neutrik, MX or equivalent)

Mic Stand (Approved Makes: Standard make)

Wooden Podium alongwith Cable Cubby (One HDMI Cable, Two LAN Cable, Two unswitched AC outlet,One 3.5 mm Mini Stereo Audio Jack,Compact size with square bezel Black color

Supply, Installation, Testing and commissioning of CE Certified 95W LED PARCAN light, 3200K, CRI > 90, Manual & DMX Control, fully RDM compliant when in DMX mode, 9° - 30° Manually Adjustable Beam Angle, Light Output @ 2 Meter > 40,000 Lux @ 9°, complete with 1 Gel Filter Frame & 3 Meter cable, Spun Aluminum housing, duly epoxy polyester black powder coated finish as per the details provided in the

Supply, Installation, Testing and Commissioning of Die cast Aluminium C Clamp with safety chain duly epoxy polyester powder coated in black matt texture finish as per the details provided in the Technical Specifications sheet.

Supply, Installation, Testing and Commissioning of Safety bond with lock clip as per the details provided in the Technical Specifications

Supply, Installation, Testing and Commissioning of 79mm Round Identification name plate duly epoxy polyester powder coated in matt texture finish as per the details provided in the Technical Specifications

Supply, Installation, Testing and commissioning of Customised MS Suspenders with fish plate & L angel with black epoxy polyester powder coated as per the details provided in the Technical Specifications sheet.

Supply, Installation, Testing and commissioning of MS C-Track with black epoxy polyester powder coated to create square grid matrix on the stage area as per the details provided in the Technical Specifications

Supply, Installation, Testing and commissioning of CE Certified fixed Light bar used as Stage Light Bar with Suitable Length, with black epoxy polyester powder coated as per the details provided in the Technical

Supply, Installation, Testing and commissioning of of Motorised Main curtain track 19 Mtrs mechanism arrangement with 1.1 KW 2pole motor and gearbox black epoxy polyester powder coated but without fabrics as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of of fixed Rear curtain track 19 Mtrs mechanism arrangement with black epoxy polyester powder coated but without fabrics as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of MS Fabricated 4 way IEC Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX male plug made up of 22SWG CRCA, black epoxy polyester powder coated as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of MS Fabricated Auxilliary marshalling box with suitable connectors & Glands made up of 22SWG or lesser SWG CRCA, black epoxy polyester powder coated as per as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of MS Fabricated Motor Cable Termintion box with suitable connectors & Glands made up of 22SWG or lesser SWG CRCA, black epoxy polyester powder coated as per as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of MS Fabricated Direct Light Distribution board duly epoxy polyester powder coated as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of MS Fabricated 1 Way Motor Control Center Panel for light bars only duly epoxy polyester powder coated as per the technical specification provided in the data

Supply, Installation, Testing and commissioning of MS Fabricated 2 way IEC Junction box with rocker switch to power splitter and console made up of 22SWG CRCA, black epoxy polyester powder coated as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of bare copper for internal earthing system as per the technical specification provided in the data sheet.

Installation hardwares such as clamps, connectors, glands, lugs, ferruels, welding rods etc.

Supply, Installation, Testing and commissioning of Perforated 75mm Wide, black epoxy polyester powder coated as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of 5 Pin XLR Termination Connectors for DMX network as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of Black valcro tape for Cable dressing as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of Fire retardent cotton fabric with 50% Gathering for frills duly stiched as per the technical specification provided in the data sheet.Size: 10x1.5m

Supply, Installation, Testing and commissioning of FRLS 3 Core 1.5 SQMM Cable with ISI mark as per the technical specification provided in the data sheet. Make : Fenolex / Polycab / Walna / SBEE / KEI

Supply, Installation, Testing and commissioning of FRLS 4 Core 4 SQMM Cable with ISI mark as per the technical specification provided in the data sheet. Make : Fenolex / Polycab / Walna / SBEE / KEI

Supply, Installation, Testing and commissioning of FRLS 7 Core 1.5 SQMM Cable with ISI mark as per the technical specification provided in the data sheet.

Supply, Installation, Testing and commissioning of FR DMX Signal Cable with CE/ISI mark as per the technical specification provided in the data sheet. Make : Falcon / Beldon / Deepcab

Supplying, installing, testing and commissioning of Dome camera 1/2.8" CMOS, F1.6~F3.3, Fixed Iris, 120dB, 50m IR, 0.001Lux, 1920x1080@30fps, 512 GB SD card slot, IP67, IK10, PoE, Built-in Mic, Audio 1/1, Alarm 2/1, Reset button, Smart VCA function, Face capture mode, Full Metal Housing Make : Pelco/Birdeye/Axis

Supplying, installing, testing and commissioning of Bullet camera 1/2.8" CMOS, F1.6~F3.3, Fixed Iris, 120dB, 80m IR, 0.001Lux, 2592x1944@30fps, 2MP@60fps, 512 GB SD card slot, IP67, PoE, Built-in Mic, Audio 1/1, Alarm 2/1, Reset button, Smart VCA function, Face capture mode, Full Metal Housing. Make : Pelco/Birdeye/Axis

Supplying, installing, testing and commissioning of PVC Junction Box

Supply, Installation, Testing & Commissioning of 43" Commercial display built in Android OS

Supply ,Installation, Testing & Commissioning of Server Grade Machine with Minimum 3 Ghz Processor, 8GB RAM, 1 TB Hard disk along with necessary as required.

Supply of Surveillance Hard Disc Drive 6TB, Make : Seagate/WD/Toshiba

Integrated Solid Waste Management

Add GST 18 %

Add Labour cess 1%

SUBHAS SINGH CHOUDHARY (BID ID -636138)

Manish Kumar (BID ID -636134)

RAJBIR CONSTRUCTION PVT. LTD. (BID ID -636223)