PROVN OF TEMP VEH PARKING SHED, CONSTRUCTION OF SEPTIC TANK AND OTHER SANCTIONED WORKS AT AMRITSAR CANTT

Amount

B/R PORTION Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.50 Sqm but n.exc 4 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified.(15+2)

S&F Framed work confirming to FE- 290 (Gde-E- 165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete(570+34+30+30)

S&F factory made 30-40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specfied and directed. (29+3.20)

S&F 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified. (29)

S&F 300 mm mild steel ordinary rat tail door spring including roller and roller plate complete all as specified. (15)

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed (14+0.50+0.28+0.50+0.30)

S&F 300mm long Aluminium alloy. Anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed (30+1+2)

S&F Aluminium, anodised, barrel tower bolts 150 mm of extruded section and fixed (30+4+4+3+8)

S&F 150mm long Aluminium handles, cast type anodised (60+4+4+1+8)

M&L preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified. (116+6)

m & L preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer on steel surfaces complete all as specified. (27+3.25+1.62+1+50+1.30+25+105)

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 and finishing even and smooth without using extra cement complete all as specified and directed. (20+30+27.79+40+40)

M&L for preparation of new plastered surfaces and applying two coats of cement base paint of shade as approved on wall surfaces complete all as specified. (20+30+26.23+50+25)

Excavating in trenches, exc 1.5 m wide and exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil complete all as specified. (7.15+5.26+7.14+20+20+10+65+2.70)

M & L for hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface in broken boulder complete all as specified and as directed. (0.80+1.29+1+2+3+5+11)

M & L for PCC 1:5:10 type E2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete.

M&L Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified. (10.50+7.18+16+15+12)

M&L for Cutting out bricks, forming toothing for, and bonding new into old work in cement mortar 1:6 including value of new materials entering old walls and jointing and pointing (measured on vertical face in contact with old wall only) complete. (2)

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified. (3.20+5.36+7.92+5+12+5+20+10+1.65)

Removal of surplus soil to a distance not exc 50 metre and depositing where directed at a level not exc 1.5 metre above the starting point complete all as specified. (3.95+1.79+2.60+15+8+45+10+30+0.95+170)

Use and waste of formwork for fair finished flat to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc. (9.15+20.55+10+16+1.50+2.25)

All as per item No 21 above but to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) (10.50+13.22+12+11.50+2.50+11.25)

M&L Reinforced cement concrete (nominal mix) Type B-1 1:2:4 (Using 20mm Graded stone aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed. (1.00+1.86+0.80+2.30)

M&L Reinforced cement concrete (nominal mix) Type B-1 1:2:4 (Using 20mm Graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like (1.30+1.64+2+3+0.90+2.25)

M & L mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips all as specified and directed. (180+22+343.44+250+340+42+150)

M & L mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed. (35+51.10+40+65+50)

M&L for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces etc complete all as specified and directed (10.50)

S&F (minimum) 3mm thick APP film based poly meric membrance minimum weighing 3Kg per Sqm reinforced with polyester non wove fabric (weight not less than 150 gms/sqm) land on primed surface by forced application along the length of 100mm lapping strip to either sides and sealed in after cleaning down the roof by brooms complete all as specified and directed. (10.50)

M&L for 15mm rendering in cement mortar (1:4) on brick/concrete surfaces finished the surface even and smooth without using extra cement. (30+10+26.23+50+50+15+60+25)

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:3 finishing even and smooth without using extra cement complete all as specified and directed (8+7.08+7+10)

M&L for Preparation of Newly Plastered surfaces of Wall / ceiling and applying Two coats of Oil Bound Distemper over a coat of alkali resistant primer all as specified and directed. (10+2.76+22+7+17+10)

M&L for applying two coats of white wash ceiling surface and all as specified as directed by Engr-in-Charge. (8+7.08)

S&F Box type ventilator fixed type with glazing bar as per drawinhg No CE JZ-70/06-07 dated 07.06.07 with guard bars including priming coat complete all as specified and all as directed. (1.62+0.81)

S&F 3 mm thick, figured glass pin head type and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified. (0.50+0.28)

Mild steel framed work of E-165 (Fe 290) as in grills/guard bars shouldered with steel window/ ventilator frames complete all as specified. (30)

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m (0.90)

M&L Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site . Make: Rajshri or equivalent as approved. (3.15+2.46+3+2.20)

S&F 100mm long, butt hinges, medium weight, cold rolled with steel complete all as specified and directed. (6+6+6+12)

S&F non skid ceramic light coloured tiles 7 to 8mm thick (square/rectangular) (colour & shade as approved by GE) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6 & complete all as specified and directed. (10+7.08)

S&F glazed ceramic coloured tiles 450x300mm x 7-8 mm thick, etc. (colour & shade as approved by GE) on vertical surfaces such as skirting , dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface complete all as specified and directed. (25+34.82+25+10)

S&F rotational moulded polythene, triple layers, water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in position including S&F 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod complete all as specified and directed (2)

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified. (10+20+20+35)

S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified. (15+12)

Supply & fix vitreous china wash down water closet pan (padestal pattern) connection to drain and to flushing pipe, anti-syphonage pipe, etc. with flush pipe 32mm dia for low level flushing cistern including plastic water closet seat cover white , closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device ,complete as directed. (excluding flushing cistern). (2+1+2)

S&F 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve flush handle including bracket and flush pipe of polythylene of low or high density or PVC,32mm dia complete all as specified and directed. (2+2+1+2)

S&F in repair 100mm bore Cast iron floor trap, with grating including jointing to waste pipe in run lead. (2+4)

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified. (2+2+1+2)

S&F Pillar taps 15mm bore, cast copper alloy , with capstan heads, chromium plated , screwed down high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe and fixed.

S&F PVC connection 15mm size with PTMT nuts of length 600mm. (2+4+2+4)

S&F Brass Chromium plated Tubular towel rail, 20 mm dia. D type, 60 cm long between flanges (2+1+2)

S&F in repairs chromium plated angle valve 15mm bore fancy type screwed down for high pressure complete all as specified and directed. (10+6)

S&F brass cromium brass plated fancy type bib taps 15 mm bore long nose screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed (4+3+4)

S&F 15mm bore Stop valves, cast copper alloy, screwed down , high pressure, with crutch or butterfly handles , screwed both ends for iron pipe or for unions, fancy type, chromium plated with long shank and cup ( concealed type) and fixed. (2+4+2+4)

All as per item No 54 above but of concealed type. (1+2)

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as concrete bed, laid to falls in trenches in any depth including packing under, and haunching against the sides of SGSW pipes 150mm bore, after the pipes have been laid and tested including complete all as specified and directed. (14+10+15+175)

M&L SGSW drain pipes 150mm bore laid in trenches and jointed incl demolition and breaking up drain pipes ( salt glazed ware, AC or Reinforced concrete ) set in cement mortar. as specified and directed. Incl deomlition of existing line (14+10+15+175)

Cutting into existing manhole for connecting new drain pipe (150mm dia),making good to pipe and rendering, cutting out existing benching for and forming brench chennel in cement concrete 1:2:4 type B-1 smooth finished etc. (1)

M&L Brick work with sub class 'B' old size brick straight or curved on plan exc 6m mean radius built in cement mortar 1:4 (2+6+30)

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as cover slab for manhole and similar work etc complete all as specified and directed. (0.35)

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregates as in benching for manholes, bands holdfast coping, bed plate etc including slightly chamfered or rounded angles including including necessary form work, if any, and finishing exposed surface even and smooth using extra cement complete. (0.50+0.10+0.10+1+2)

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil. (8.34+3+5)

Demolition of brickwork, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed. (0.68)

Spreading and levelling in layers n exc. 25 cm thick including well ramming including watering as required. (0.71)

M&L 75 mm thick Cement concrete type D-2 , 1:4:8 using 40 mm graded aggregate as in sub base (7.83+253)

S & F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing. (9.80)

M&L for PCC (1:3:6) type C1 (20mm graded aggregate) filling in frames (0.01)

M&L 50mm thick Cement concrete type C-1 , 1:3:6 (20 mm graded aggregate) as in plinth protection (6.55+8+10)

S&F Vitreous china squatting pan, 'Orrisa' pattern , size 580x440 mm white, with integral foot rests ( excluding flushing cistern and flush pipe) including provision of lime concrete bedding and Cast iron 'P' or 'S' traps (2)

S&F 15mm bore bib taps, cast copper alloy with crutch or butterfly handle , screwed down , scrwed for iron pipe or for brass ferrule and fixed (6)

S&F 110mm bore PVC(SWR) pipes single socketed in any length laid in trenches including all fittings complete all as specified and directed by Engineer-in-charge Make:-supremo,Finolex,Jyoti. (10+5+20+5+5)

S&F 110mm bore PVC (SWR) bends any radius With access door (4)

M&L 110 mm bore PVC (SWR) floor trap ,plain with grating including jointing with solvent cement (4+3+4)

S&F for 500ltr cap rotational moulded polyethylene water storage tanks ( cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I. (2)

S&F 20mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. .(Minimum weight 15mm-142gms/ 20mm-210 gms./25mm-455gms/ 40mm - 690 gms) (2+1+1)

S&F in repairs 125mm CP shower rose fancy type with CP arm complete all as specified and directed. (2+4)

M&L Damp proof course in CM 1:2:4type B-0 to horizontal or vertical surfaces including necessary formwork complete all as specified and directed. (2.50+6.50)

M&L for Vitrified ceramic light shade tiles 10mm thick (Square/ rectangular) polished, area of each tiles n.exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including screed bed or bedding layer of cement mortar(1:6) 15mm thick for laying floor finishes complete all as specified and directed. (7+12)

Supply and fixing Chromium plated Health faucet with 1.5 metre long chain. (1+2)

S&F for 1000ltr capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed. (1+1)

S&F soap dish, vitrous china white, approximate size 160 x 160 x 90 mm embedded in the wall complete all as specified and directed. (1+2)

S&F Vitrous china white (Box type) toilet paper holder fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. (2)

Excavation over areas Exc 1.5m in depth and getting out in soft / loose soil. (56+125)

Material and labour for brick work with sub-class 'B' bricks straight or curved on plan to any radius in half thick brick walls built in CM 1:4 complete all as specified and directed (11+22)

M&L for Brickwork, with subclass 'B' bricks in full brick thick honey comb walling in CM 1:4 complete all as specified and directed. (5.50+12)

M&L for Loosing filling with aggregates of broken bricks of gauge 80 to 150 mm in soakage pits, soakage wells (8+16)

All as per item No 86 above but of gauge 40 to 80 mm (7+15)

S&F Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers , stop valve boxes, gate stops, parts of ranges , balusters and similar articles exc 5 kg each. (90+150)

S&F Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers , stop valve boxes, gate stops, parts of ranges , balusters and similar articles not exc 5 kg each. (5+5)

Excavating in post holes( or similar holes) in soft/loose soil each n exc 0.5 cu.m. getting out, surplus soil to a distance n.exc 50 m and making good surface. (12+36)

M&L for Moorum/ red bajri/ loose soil filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering. (20)

S&F mild steel Gde Fe-410-W as in roof trusses, (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee,angle,channel or flat sections) including distance pieces , cleats etc. (1250+3440)

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified. (60+250)

M&L for black bituminous paint with two coat of surfaces of any description wood, steel,iron,concrete,brick,stone etc exceeding 10 cm in width or girth all as specified and directed. (1.50+7)

M&L for 100mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in path and finishing the surface even and smooth without using extra cement complete all as specified and directed. (70)

M & L Chequered cement concrete tiles 30cm x 30cm x 22mm thick over and including 20mm thick bedding layer in cement mortar 1:6,set and jointed in neat cement slurry and pointed in grey cement and pigment to match the colour of tiles complete all as specified and directed by Engr-in-charge. (250)

E/M PORTION Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, sockets, lamp holders, brackets, bulk head fittings, tube light fittings etc. and making good disturbed surfaces of walls etc. as per existing finishes by plastering, repairs and white / colour wash etc. complete all as specified and directed.

S & F point wiring for one light point / fan point / bell point / 5 Ampere socket outlet point, controlled by one, one way switch with 1.50 sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FR) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated 1.50 sqmm size copper conductor cable as in earth wire and connected to common earth dolly complete all as specified and directed, are as follows :-Make RR Kabel/Polycab/Havells (a) One light/one fan/one bell point controlled by one, one way switch. (3+4+4+8)

All as per item No 98 but one socket outlet 5 pin 5 Amp controlled by one, one way switch on same board. (1+1+1+2+1)

All per item No 98 but one socket outlet 5 pin 5 Amp controlled by one, one way switch on indipendent board. (1+1+1)

Supply and fixing of switch piano flush button single pole one-way 5 Ampere complete all as specified and directed. Make Anchor/Plaza/SSK (11+6+15+6)

Supply and fixing of socket outlet 5 Ampere, 2 and 3 pins (TOTAL 05 PINS), flush type 250 volts AC complete all as specified and directed. Make Anchor/Plaza/SSK (2)

Supply and Fixing Ceiling rose, surface bakelite 3 terminal, 240 volts, 5 Amps with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size ,complete ,all as specified. Make Anchor/Plaza/SSK (1+2+4)

S & F lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed. Make Anchor/Plaza/SSK (1+4)

S & F MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘C’ curve type complete all as specified and directed. Make Legrand/Schneider/Siemens (1+2+2+2)

S & F MCB double pole, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, ‘C’ curve type complete all as specified and directed. Make Legrand/Schneider/Siemens (1+2)

S & F sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 4 ways with 200 ampere rated bus bar, 240 volts fixed sunk / flush to the wall with IP-43 and IK-09 protection complete all as specified and directed. Make :- Legrand/ C&S /Schneider (1)

M & L for sub main wiring with 1100 volt grade two single core FR Wire PVC insulated and unsheathed cable with stranded copper conductor 4 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 4 sqmm multi - stranded copper conductor as earth wire in green colour complete all as specified and directed. Including taking down old unserviceable sub main wiring .NOTE: 2 single core 4 sqmm and one 4 sqmm cable and PVC conduit shall be measured as one RM. Make RR Kabel/Polycab/Havells (8)

S & F wall /ceiling mounting LED 18 Watt pride plus/smart line tube light fitting complete with all acessories 1x18 Watt LED , suitable for domestic application, 240 Volts, 50 Hz, and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete as per or its equivalent approved make inj complete all as specified and directed. Make :- Havells/Philips/Wipro (1+2+2)

S & F fan regulator electronic step type socket size and making all necessary connections complete all as specified and directed.Make Anchor/Plaza/SSK (1)

S&F energy saving new generation 10 watt LED, 6000k bulk head luminaire with opal diffuser light fitting complete with all acessories and connection complete. Make Philips/Wipro/CG (1+1)

S&F Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s etc complete all as specified. (Note : cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc is included in quated rate) Make Schneider/Legrand/Siemens (1+1+1)

S & F in repair MCB double pole, 240 volts, 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed. Make Schneider/Legrand/Siemens (1+1)

Material and labour service connection PVC cable 6 Sqmm 2 Core incl GI wire and PVC conduit for fixing in wall /pole incl connection completed all specified and directed. (50+40)

Supply and fix Socket outlet 2 in 1, 3 pin 5 Amps Flush type. Make Anchor/SSK/Plaza (2+11)

S & F in repair MCB double pole, 240 volts, 16 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed. Make :- Legrand/ C&S / Schneider (1)

M & L for sub main wiring with PVC insulated, 1100 volts grade single core multistranded copper conductor cable conforming to IS specifications, 2 runs of 2.5 sqmm including 1 run of 2.5 sq mm single core multistranded copper conductor, PVC insulated cables as earth continuity conductor drawn through and including one run of 25 mm dia rigid PVC conduit and conduit accessories fixed on wall/ceiling etc., or concealed in wall and connecting to common earth dolly all as specified and directed including taking down all sub main wiring . Make of FRLS wire; Polycab/Havells/RR Cable,Make of PVC Pipe - Polycab/FInolex/Kalinga premium. Note : 2 Run of 2.5 sqmm, 1 Run of 2.5 sq mm and 1 run of PVC conduit will be mesuared as 1 unit. (20)

S&F exhaust fan 230 mm sweep metal body including cutting of wall /window/lowers and fixing arrangement complete all as specified and directed.Make Crompton/ Greaves Havells/Bajaj (2)

M & L for laying of LT cable of 1100 volt XLPE insulated and PVC sheathed armoured cable of size 6 sqmm 2 core with cable gland including taking down old unserviceble cable complete all as specified and directed by Engineer-in-Charge.Make Havells/ Glostar/ polycab. (15)

M & L for brick protection to cable using old size sub class 'B' bricks, laidflat, dry butt jointed, laid lengthwise perpendicular to the axis of cable all as specified & directed. (0.08)

M&L for sand cushioning with layer of sand 8 cm thick before laying of cable and 15 cm after lying of calbe in trenches complete all as specified & directed. Note : Thickness after punning down shall be measured (0.90)

Supply and fixing /laying galvanised pipe 50 mm bore medium grade fixed to pole with clamps nuts, bolts and washers or laid under road crossing or fixed to wall complete all as specified and directed. (3)

Supply, laying and fixing of 20 mm bore tubes (medium grade) galvanised with all fitting and fixed to walls and ceiling or laid in floors and made a proper connection with existing pipe line incl necessary excavation and reutrning filling of soil all as specified and directed by Engr-in-Charge. (20)

Supply and fixing of PPR Gate valve (Brass insert) of size 20mm complete all as specified and directed by engr in charge. (1)

MAAN ENTERPRISES

BISHAN DASS

NU DOLPHIN ENTERPRISES