Providing Upgradation LT outdoor feeder at E Type D Type C type old B type Block II and Old B Type Block III Qtrs at IISc

Amount

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts and wiring complete. Protection of Overload and Short circuit with thermal Magnetic/Micro processor release and Earth Fault as per IS-13947. ( Icu = Ics).250Amps 35kA.Three Pole

Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts and wiring complete. Protection of Overload and Short circuit with thermal Magnetic/Micro processor release and Earth Fault as per IS-13947. ( Icu = Ics).400Amps 35kA.Three Pole

Supplying ......... amps rated 3phase with neutral bus bar using required capacity electrolytic aluminum strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., complete.100Amps 4x30x6mm Aluminum Strips

Fabricating supplying and mounting MS box made out … SWG suitable for floor / wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enameled metal paint etc., complete.16SWG

Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. flat … with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. 50x50x6mm

Supplying and fixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only).32mm dia

Supplying and fixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only).100mm dia

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes.240 sqmm Long Barrel

Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes.10 sqmm Long Barrel.

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve , indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IES 60898.40-63Amps TPN

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve , indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IES 60898.100 A TP&N (MR) D'Mak Energia make:Havells

Supplying fixing and wiring earth electrode for grounding of lifts, transformers, DG sets etc. using 40mm dia 2.9mm thick 2.5 mtr long GI pipe with GI funnel with mesh and suitable size reducer fixed on the top of the earth electrode. The funnel should be enclosed in a CC chamber of 400x400x400mm with a cast iron cover. The earth electrode shall have staggered holes of 12mm dia and the electrode should be covered 150mm all-round with alternate layers of salt and charcoal from the bottom of the CC chamber. The connection from the electrode is to be established through GI strip using GI bolts and nuts.

Supplying and running GI/Copper conductor for grounding and (along with other wires in conduit system of wiring) using necessary suitable size clamps, nails, guttas/spacers etc.GI strip.25x3mm

KSRB 2-2 : Earthwork excavation by manual means for foundation of buildings,water supply and sanitary lines and electrical conduits etc, either in pit or in trenches 1.5m and above in width, in soil not exceeding 1.5m in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation with lead upto 50m. including breaking of clods complete as per specification:2.2.2:-do-in hard soil.

Providing and laying in position plain cement concrete of mix M 1:4:8 with OPC cement @ 240 kgs, with 20mm and down size graded granite metal coarse aggregates @ 0..69cum and fine aggregates @ 0.45cum machine mixed, concrete laid in layers not exceeding 15cms thick, well compacted, in foundation including cost of all materials, labour, HOM of machinery, curing complete as per specifications.

Providing 18mm thick cement plaster on walls in single coat with cement mortar to brick masonry including rounding off corners wherever required smooth rendering, : Providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications. cement mortar 1:4

Supplying of 1.1 KV LT UG cable having aluminum conductor PVC insulated, extruded inner sheathed, galvanized, steel strip (except 2CX10Sq.mm wire armoured) confirming to IS-3975:1990 (No. of Strip indicated in GTP) & extruded PVC outer sheathed armoured cable with specified IS-1554 Part-1:1988 & confirming to GTP of GROUP-A.3.5 core 95 sqmm.

Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required.In existing trench/duct.95sqmm to 150Sqmm.

Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., complete.Asphalt Cutting

Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., complete.In soil (hard).

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Providing and fixing to wall, ceiling and floor, high density polyethylene pipes 6.00 kgf/sq.cm working pressure32mm outside diameter with special flange, compression type fittings, wall clips, making good the wall, ceiling and floor, including cost of all materials, labour charges, HOM of equipments and testing complete as per specifications.-63mm dia

Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 220v A.C. 50 Hz 12/24v D.C.

BASIC RATES OF LABOUR & HIRE CHARGES for Existing Old Panel dismentaling work DELHI SCHEDULE OF RATES (E&M) .Beldar/ coolie

BASIC RATES OF LABOUR & HIRE CHARGES for Existing Old Panel dismentaling work DELHI SCHEDULE OF RATES (E&M) Electrician

Manjunatha Electricals

POWER AND LIGHT CONTROLS

G R Electricals

classic eletricals and egineers

M/S Chaya & Co