Internal Electrification and Cable Carrier System for Building no.105, 206, 210-A and 301 at FRFCF, Kalpakkam.

Amount

Supply and installation of Surface mounting Powder Coated TPN 250A,3ph,415V,50Hz, 12Way Vertical DB with 1no of I/C-4P, 250A MCCB and 12 no's of O/g's-3P, 63A MCB with all accessories as per the scope of work.

Supply, Installation, testing and commissioning of the following MCBs/RCBOs on Distribution Boards as per the detailed specification. (Refer Sec VI, Clause No.14.2).

6-32 Amps SP MCB (Type-C)

6-32 Amps DP MCB (TYPE-C)

40-63Amps, DP MCB (TYPE-C)

RCCB DP 40A sensitivity 30mA, TYPE AC

40-63Amps, FP MCB (TYPE-C)

125Amps FP MCB (TYPE-C)

RCBO FP 63A sensitivity 30mA 4Module

Supply and external installation of following sizes of Heavy Duty, Hot Dip Galvanised MS ERW Conduits for Electrical & Communication System with all the required accessories like round JBs, Solid Long Bends, Check Nuts, Nipples, Couplings, Reducers, Copper Clips, Copper Conductor, GI Wire etc. as per the detailed specification. .(Refer Sec VI, Clause No.27).

25 mm Dia 1.8mm, wall thickness Heavy Duty ERW Conduits with 50mm deep junction boxes

25mm GI Flexible Hose

Wiring for lights/fans/sensors/Timer/Power point with 1100V grade FRLS insulated copper conductor wires in existing concealed/Exposed ERW hot dip GI conduits as per the detailed scope of work, including supply of Wires, switches/sockets, termination of copper wires at both the ends by crimping, including supply of rubber bushes, PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification.(Refer Sec VI, Clause No.18).

Wiring for Light/Sensor/Fan Points with 2 Runs of 1.5 Sq.mm copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm copper wire for Earth from MCB Distribution Board to Primary light/sensor/fan point through Control Switch Box including 10Amps modular switch. (Average Length 25Mtrs)

Wiring for Light point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch box to switch box and further to Light point including 1 No 10A modular switch.(Average Length 17Mtrs)

Wiring for Light point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch box to Light point/Ceiling fan including 1 No 10A modular switch. (Average Length 17Mtrs)

Wiring for Light point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Light point to Light point /sensor/contactor. (Average Length 4Mtrs)

Wiring for Light point with 2 Runs of 4 Sq.mm Copper wires for Phase, Neutral and 1 Run of 2.5 Sq.mm copper wire for earth from MCB Distribution Board Earth from Distribution Board to Light point through MCB Switch Box including supply of one No. of 10A, SPMCB (more than 5.5 meter height). (Average Length 52Mtrs)

Wiring for Light point with 3 Runs of 2.5 Sq.mm Copper wires for Phase, Neutral and Earth from Light point to Light point (more than 5.5 meter height) (Average Length 10Mtrs)

Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from MCB Distribution Board to Power point through Control Switch Box including supply of 16A modular switch, 6/16 Amps combined shuttered type Socket, 3Modular plate 1No. (Average Length 15Mtrs)

Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from MCB Distribution Board to Power point through Control Switch Box including supply of 16A modular switch, 6/16 Amps combined shuttered type Socket, Modular plate.(More than 19mtr height)

Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase, Neutral and Earth from MCB Distribution Board to Power point through Control Switch Box including supply of modular plate, one No. of 16A modular switch & one No. of 6/16 Amps combined shuttered type Socket and Three Numbers of 10A modular switch & Three numbers of 3 pin, 6A shuttered type Socket, Modular plate. (Average Length 18Mtrs)

Wiring for Power point with 2 Runs of 1.5 Sq.mm copper wire for Phase & Neutral and 1 Run of 2.5 Sq.mm copper wire for Earth from MCB Distribution Board to Power point through Control Switch Box including 10A modular switch, 3 pin 6A shuttered type Socket, Module Plate. (Average Length 30Mtrs)

Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from MCB Distribution Board to Power point through Control Switch Box including 16A modular switch, 6/16 Amps combined shuttered type Socket and 10A modular switch & 3 pin, 6A shuttered type Socket, Modular Plate. (Average Length 20Mtrs)

Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from MCB Distribution Board to Power point through Control Starter Switch Box including supply of 16A modular Starter switch, 6/16 Amps combined shuttered type Socket, 2 Modular plate 2 Nos. (Average Length 22Mtrs)

Wiring for Exhaust fan point up to 3Mtr height with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from MCB Distribution Board to Power point through Control Switch Box including supply of 3 pin 6A shuttered type Socket, 2Nos. 2 Modular plate and 1 No 10A modular switch. (Average Length 12Mtrs)

Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from Control Switch Box to control switch box including supply of 16A modular switch, 3 pin 6/16 A combined shuttered type Socket, Modular plate. (Average Length 3Mtrs)

Wiring for Power point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm copper wire for earth from Control Switch Box to control switch box including 10A modular switch & 3 pin 6A, shuttered type Socket, Modular plate. (Average Length 5Mtrs)

Wiring for Power point with 2 Runs of 1.5 Sq.mm copper wire for Phase & Neutral and 1 Run of 2.5 Sq.mm copper wire for Earth from MCB Distribution Board to Power point through Control Switch Box including 10A modular switch 3 pin, 6A shuttered type Socket, Module Plate. (more than 5.5mtr height)

Wiring for Exhaust fan point up to 3 Mtr height with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch board to Power point including supply of 3 pin 6A shuttered type Socket, 2Nos. 2 Modular plate and 1 No 10A modular switch. (Average Length 8Mtrs)

Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from Control Switch Box to control switch box including 10A modular switch & 3 pin 6A, shuttered type Socket and 16A modular switch & 6/16A combined shuttered type Socket, Modular plate. (Average Length 9Mtrs)

Wiring for lights / fans /sensors/ Power point with 1100V grade FRPVC insulated copper conductor wires in existing concealed/ Exposed PVC / ERW/Flo-coated Metal conduits as per the detailed scope of work, including supply of Wires and termination of copper wires at either end by crimping including supply of PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification.(Refer Sec VI, Clause No.18).

Wiring with 1 Run of 1.5 Sq.mm Copper wire

Wiring with 1 Run of 2.5 Sq.mm Copper wire

Wiring with 1 Run of 4 Sq.mm Copper wire

Supply and Embedment of 50mm Deep, Square/Rectangular Concealed type and GI double earthed modular metal boxes of the following types and as specified in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification. (Refer Sec VI, Clause No.15.12).

1/2 Module

3 Module

4 Module

6 Module

Supply and fixing of following front Modular cover plate on existing modular metal/plastic boxes etc. as required. (Refer Sec VI, Clause No.15.7).

1/2 Module

3 Module

4 Module

6 Module

1 Modular dummy plate

Supply and embedment of concealed type MS boxes of the following types and as specified in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification. (Refer Sec VI, Clause No.15.10).

150(W)X150(H)X80(D)mm, 1.6mm thick sheet MS Box

200(W)X200(H)X120(D)mm,1.6mm thick sheet MS Box

300(W)X300(H)X120(D)mm,1.8mm thick sheet MS Box

Supply, transportation, installation, testing and Commissioning of the following type of Recess mounted luminaires. (Refer Sec VI, Clause No.16.1).

2*2 feet Recess Mounted LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 2500, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

2*2 feet Recess Mounted LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 3600, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

4 feet Recess Mounted LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 4300, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

Recess Mounted LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 1200, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit for 110/220V DC and complete with all accessories including mounting arrangements with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

Supply, fabrication and embedment of Junction/Termination Box with MS Body, 6mm thick bottom MS Plate, Stainless Steel Top & Bottom Flanges for mounting of Bollard & LED luminaire with CCT of 5700K, having a minimum CRI of 80, lumen output of minimum 880, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP65, supply of cable termination arrangements,2.75mtr 50NB GI pole and 32NB dia single arm GI pole PU painting, as per Drawing No.IGC/ESD/4013/1001/R1, including providing of 1:4:8 mudmat and 1:3:6 foundation PCC conforming to the detailed specification 1mtr 16mmDia SS rod with SS wire (2 runs) equivalent to 8SWG and as per Drawing No:IGC/ESD/4013/1001/R1.

Supply, transportation, installation, testing and Commissioning of the following type of Surface mounted luminaires.(Refer Sec VI, Clause No.16.1).

2 feet Surface Mounted LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 1200, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements required to mount on wall/ suspended from 5 meter ceiling with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

SCEL Surface Mounted, Portable non-maintained emergency LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 1200, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing with minimum 8hrs battery back-up, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements required to mount on wall/ suspended from 5 meter ceiling with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

4 feet Surface Mounted LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 4300, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements required to mount on wall/ suspended from 5 meter ceiling with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

Wall/Surface Mounted LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 10000, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements required to mount on wall/ suspended from 5 meter ceiling with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

Wall/Surface Mounted LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 15000, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements required to mount on wall/ suspended from 5 meter ceiling with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

Supply, transportation, installation, testing and Commissioning of the 4 feet Surface Mounted 2*20W LED twin tube flame proof luminaire with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 4400, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP65, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuitand complete with all accessories including mounting arrangements required to mount on wall/ suspended from 5 meter ceiling with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

Supply, transportation, installation, testing and Commissioning of the following type of Suspended LED mounted luminaires.(Refer Sec VI, Clause No.16.1).

4 feet Suspended LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 4300, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements required to mount on wall/ suspended from 5 meter ceiling with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

Suspended LED Luminaires with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 25000, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements required to mount on wall/ suspended from 5 meter ceiling with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

Supply, transportation, installation, testing and Commissioning of LED luminaries on Metalic poles with CCT of 6500K, having a minimum CRI of 80, lumen output of minimum 4300, minimum lumen efficiency of 110 lm/w, ingress protection minimum of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminium housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements requiredon Metalic poles of height from 2.5 M to 4 M with provision and connection for 2.5 sq.mm flexible copper conductor of PVC insulation wire, etc., as per the detailed specification and instruction of Engineer-in-Charge.

Supply, installation, testing and commissioning of following sizes of Wall Mounting Exhaust Fans including supply of Aluminium grill bracket with Stainless Steel Bolts for mounting of Exhaust Fan & Aluminium grill bracket and 3 Core, 1.5 Sq.mm (14/0.3) PVC insulated & FRLS sheathed copper flexible cable of required length as per the detailed specification. (Refer Sec VI, Clause No.17.2).

300 mm Dia Turbo Heavy Duty Exhaust Fan

450 mm Dia Turbo Heavy Duty Exhaust Fan

Supply, installation, testing and commissioning of 450 mm Dia Industrial Wall Mounting Fans as per the detailed specification.. (Refer Sec VI, Clause No.17.4).

Supply, Installation, Testing & Commissioning of OPC Drum, Cleaning Blade & Developer for PlotWave 340 & 360 Printer(Plotter) as per the detailed specification and instruction of Engineer-in-Charge.

Supply and installation of 70 Sq.mm multi Stranded tinned copper Earthing conductor with test link in Walls, Floors, Built in Trenches including supply of GI spacer and clamps, fixing fasteners etc as per detailed specification. (Refer Sec VI, Clause No.12.5).

Supply & Installation of 185 Sqmm multi Stranded tinned Copper Earthing Conductor direct in ground including excavation, and back filling the trench as per detailed specification. (Refer Sec VI, Clause No.12.5).

Supply and installation of the 8 SWG copper wire in built in trench as per the detailed specification.(Refer Sec VI, Clause No.12.8).

End Termination of the following sizes of annealed, tinned, stranded Copper conductor including supply of copper crimping lugs etc. (Refer Sec VI, Clause No.12.6).

70 Sqmm stranded tinned Copper conductor

185 Sqmm stranded tinned Copper conductor

Jointing of following size of the tinned standard Copper conductors by Exothermic Welding (CAD Welding) joint complete with all components and accessories as per the scope of work and drawings.

T -Type joint 70 Sq.mm conductor

T -Type joint 185 Sq.mm conductor

Cross (+) -Type joint 70 Sq.mm conductor

Supply installation and testing of Maintenance free earthing system (1x10feetx5/8inch copper bonded steel rod, 22 kg Ground Enhancing Material (GEM) ) as per IS: 3043 including RCC Chamber and RCC cover slab as per Drawing No.IGC/ESD/5060/1008/1 enclosed. (Refer Sec VI, Clause No.12.12).

Supply, installation, testing and commissioning of SDFU TPN 63A, DIN FUSES with 3Nos 63A HRC fuse links, Sheet steel factory made enclosure with MS frame work as per the scope of work. (MS item will be measured separately). (Refer Sec VI, Clause No.14).

Supply Embedment Assembling testing and commissioning of following type Metra plug and socket DB and RCBO in sheet steel enclosure including chipping and finishing as per the detailed specification. (Refer Sec VI, Clause No.15.4).

16A 2P+E-DP Metra plug and socket DB and 16A DP 30mA sensistivity RCBO

32A 3P+N+E-FP Metra plug and socket DB and 32A FP 30mA sensistivity RCBO

63A 3P+N+E-FP Metra plug and socket DB and 63A FP 30mA sensistivity RCBO

Supply, fabrication and installation of the following size of Hot dip Galvanised GI Flats in Built in trenches on walls, poles, RCC Concrete and through embedded pipes as per the detailed specification. No cutting or drilling permitted after galvanisation. (Refer Sec VI, Clause No.12.9).

25 X 6 mm GI flat

50 X 6 mm GI flat

Fabrication, Supply and installation of the following size of hot dipped galvanized (average weight of zinc coating per unit area - 610 gm/Sq.m and coating thickness minimum of 75 microns) steel (IS:2062 Grade-BR), "Ladder type cable trays" with GI coupler plates, SS bolts, nuts & washers as per drawings, scope of work and as directed by the Engineer-in-Charge.

150 mm width x 100 mm depth x 2.0 mm thickness

300 mm width x 100 mm depth x 2.0 mm thickness

600 mm width x 100 mm depth x 2.0 mm thickness

Fabrication, Supply and installation of the following size of hot dipped galvanized (average weight of zinc coating per unit area - 610 gm/Sq.m and coating thickness minimum of 75 microns) steel (IS:2062 Grade-BR), "Perforated type cable trays" with GI coupler plates, SS bolts, nuts & washers as per drawings, scope of work and as directed by the Engineer-in-Charge.

150 mm width x 100 mm depth x 2.0 mm thickness

300 mm width x 100 mm depth x 2.0 mm thickness

600 mm width x 100 mm depth x 2.0 mm thickness

Fabrication, Supply and installation of the following size of hot dipped galvanized (average weight of zinc coating per unit area - 610 gm/Sq.m and coating thickness minimum of 75 microns) steel (IS:2062 Grade-BR), "Solid type cable trays" with GI coupler plates, SS bolts, nuts & washers as per drawings, scope of work and as directed by the Engineer-in-Charge.

150 mm width x 100 mm depth x 2.0 mm thickness

600 mm width x 100 mm depth x 2.0 mm thickness

Fabrication, Supply and installation of 150 mm width x 100 mm depth x 2.0 mm thickness of hot dipped galvanized (average weight of zinc coating per unit area - 610 gm/Sq.m and coating thickness minimum of 75 microns) steel (IS:2062 Grade-BR), "Cable tray Cover" with GI coupler plates, SS bolts, nuts & washers as per drawings, scope of work and as directed by the Engineer-in-Charge.

Supply and Installation of MS Brackets, Supports, Frame work, Clamps, Base Channels, etc. fabricated out of angle / Channel / Rods etc. The rate quoted shall include the cost of fabrication / welding, cleaning and painting/ galvanising as follows including supply of required, fasteners, nuts, washers, etc.(Refer Sec VI, Clause No.11).

MS fabrication 1 coat primer & 2 coats synthetic enamel paint

GI: MS fabrication With hot dipped galvanising.

Loading, Transportation, Unloading at site, installation, Testing and Commissioning of 1100 Volts Grade PVC/HRPVC/XLPE insulated, Stranded Aluminium/copper conductor cables of following sizes in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification (Note: Cable will be issued free of cost by the department).(Refer Sec VI, Clause No.3)

3/3.5/4core X Upto 25 sqmm

3/3.5/4Core X above 240 & up to 400 sqmm

End Termination of 4C x 2.5 Sq.mm Copper Conductor PVC/XLPE Insulated and FRLS sheathed armoured UG Cable using Single Compression, Heavy Duty, Siemens type Brass Gland connecting the cable to the equipment such as Switches/Panel Boards etc. using Copper crimping lugs as directed by Engineer-in-Charge. The rate shall include the cost of supply of Cable Gland and Lugs. The Contractor shall arrange for making holes wherever necessary for fixing cable gland. (Refer Sec VI, Clause No.10.1).

End Termination of the following sizes of Aluminium Conductor PVC Insulated and sheathed armoured UG Cable using Single Compression, Heavy Duty, Gland connecting the cable to the equipment such as Switches/Panel Boards etc. using Comet or equivalent make Aluminium crimping lugs as directed by Engineer-in-Charge. The rate shall include the cost of supply of Cable Gland and Lugs. The Contractor shall arrange for making holes wherever necessary for fixing cable gland. (Refer Sec VI, Clause No.10.1).

4 Core X10 Sq.mm

4 Core X 16 Sq.mm

3.5 Core x 400 Sq.mm

Supply and Installation of laminated Hylam sheet of 3mm thickness over the boxes and as per the detailed specification.

Supply and installation of 150 mm Dia. 2 Mtrs Long, NP 2 Class Hume Pipes Direct in ground at a depth of 1200 mm including supply of Collars and fixing them with1:1 cement mortar and curing, including excavation in all types of soil, backfilling complete as directed by the Engineer-in-Charge. (Refer Sec VI, Clause No.8.1).

Design, supply, installation, testing and commissioning of the 415 V Indoor Motor Control Centre with form 4B and drawout type 4 Pole Air Circuit Breakers for incoming feeders, Buscoupler and 3/4 Pole MPCB/MCCB's for outgoing feeders with associated accessories as per the detailed specifications and scope of work as directed by the Engineer-in-Charge.

Excavation of soil including refilling with excavated earth and disposing surplus earth at places as directed with in a lead of 10 Mtrs. and initial lift upto 1.5 Mtrs. including neat banking as per detailed specification. (Refer Sec VI, Clause No.2).

Post top Lantern pole including supply and embedment of Cast Aluminium Junction Box with FRP cover as per the drawing No: - IGC/ESD/2021/6001/1-R1. 3.75mtr 50NB GI pole with PU painting, cable entry pipe, cable termination arrangements etc. including providing of 1:4:8 mudmat and 1:3:6 foundation PCC conforming to the detailed specification 1mtr 16mm Dia SS rod with SS wire (2 runs) equivalent to 8SWG and as per Drawing No. - IGC/ESD/2021/6001/P2-R1. (Refer section VI Clause 13.6)

Supply, fixing and wiring of 2mm MS Powder coated junction boxes with elmax connector fo 20nos of 2.5Sq.mm, size 200mm * 200mm * 150mm will elmax connector of 20nos including cable lugs and custom printed ferruls with C-chennel as directed by the Engineer-in-Charge.

Fabrication, Supply, transporting, unloading, shifting and installation of digital equipment table 750 mm (H) x 1000 mm (W) x 500 mm (D) key board tray and drawer at required places as instructed by Engineer-in-Charge.

Fabrication, Supply, transporting, unloading, shifting and installation of S type chair with arm rest Made of Polythene Cane as instructed by Engineer in-charge.

Fabrication, Supply, transporting, unloading, shifting and installation of non-revolving with full desklet chair made up of 25 mm Mild steel pipe and wall thick ness 1.1mm with foldable writing pad on one side and arm rest on other side and poly urethane form Cushioned seat with Paper tray made of MS Wire spot welded to make mesh as instructed by Engineer in-charge.

Fabrication, Supply, transporting, unloading, shifting and installation of Wooden top equipment table with 750 mm (H) x 1200 mm (W) x 600 mm (D) with steel stand, one side storage 3 racks with lock and foot rest as instructed by Engineer in-charge.

Fabrication, Supply, transporting, unloading, shifting and installation of Conventional File storage unit of 1981 mm (H) x 916 mm (W) x 486 mm (D) five loading levels with accessories like cradle, instadex file hard cartboard etc and locking system as instructed by Engineer in-charge.

Supply & laying of 1 pair, 1.5 sq.mm Stranded copper conductor, flexible un-armored cable, insulated Class-A, FRLS cable for FDAS as per the scope of work and as directed by the Engineer-in-Charge.

Supply & laying of 1 Pair, 1.5 sq mm Stranded copper conductor, flexible un-armored cable, FRLS PVC sheath, insulated cores, twisted pair, Overall screened with Al-Mylar tape, voltage grade 1100V, applicable standard IS 1554 for PA system as per the scope of work and as directed by the Engineer-in-Charge.

Supply & Laying of CAT-6 UTP Cable through embedded conduit / cassing-capping for Telephone system, CCTV System and LAN System as per the scope of work and as directed by the Engineer-in-Charge.

power system

EC Enterprises