Construction of Temporary Shed for Workers at Marine Workshop Betim.

Earthwork in surface excavation not exceeding 30 cm depth(but exceeding 1.5 m width as well as 10 sq.m on plan) including disposal of excavated earth beyond work site for all leads lift disposed earth to be leveled and neatly dressed in:

Ordinary soil

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m.

All kinds of soil

Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete.

Moorum

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded granitic or basaltic stone aggregate 40 m nominal size) excluding cost of centering, shuttering and finishing :

All works upto plinth level

Providing and fixing cement sheet 25mm thick in partitions fixed to MS frames with brass srews etc. Complete (frame to be paid separately) as per the instruction of Engineer in Charge.

Providing and fixing Mosquito netlon with welcrow.

Providing and fixing Seat in wood including finishing as per the drawing and direction of Engineer In Charge. Rate is inclusive of dismantling and disposal of the same.

Proving and fixing anodised alluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Window with two or three sliding shutters using 14.5/15 mm series shutters section.

Plain glass

Providing and fixing anodized aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Adjustable louvered windows.

Figured glass

Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section

Providing and fixing flush doors shutters commercial type, core of block board construction with frame of first class hard wood and well matched commercial ply veneering and vertical grains or cross bands and face veneers on the both other faces of shutters.

40 mm thick including anodized aluminium butt hinges with necessary screws:

Providing & fixing colour coated Alluminium (PUF) sandwich panel roofing systems of approved make adhering to Aluminium 3105 grade for top & bottom sheet of thickness 0.40 & 0.35 respectively including PUF insulation betewwn the top & bottom sheet of Denslity 40 (+/-2) Kg/m3 inclusive of S.S.304 grade self tapping fastneres, complete as directed by Enigneer incharge (frame work for roof, roof accesorries to be paid seperately) for tile Design PUF roof panel, Gutter width should be atleast 25% more than the Crest width. Minimum height at heighest point of Crest should be minimum 65mm. Minimum thickness at anygiven point should not be below 30mm.

PUF Insulated tile roof 30mm thick of trapezoidal design

Providing & Fixing Alluminium Barge Board of approved make adhering to Alluminium 3105 grade of 0.71mm thickness & 60 cm wide inclusive of SS304 grade self tapping fastners, to match the Alluminium roofing system & as directed by Engineer in charge complete

Providing & Fixing Alluminium Corner flashing/ Gutter Valley of approved make Alluminium 3105 grade of 0.71mm thickness & 60 cm wide inclusive of SS304 grade self tapping fastners, to match the Alluminium roofing system & as directed by Engineer in charge complete

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm.

80 mm thick in all colours except grey (M40 grade)

Providing and fixing M.S. door latch with screws etc. Complete

Providing and fixing M.S. tower bolts (barrel type) with necessary screws etc. Complete

Providing and fixing M.S. handles with necessary screws etc. complete.

Providing and fixing oxidised M.S. pressed butt hinges bright finished with necessary screws etc. complete.

Steel work in single sections (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only) including cutting, hoisting fixing in position and applying a priming coat of red lead paint.

In R.S. joists, channels, angles, tees

Providing and and laying vitrified floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete

600x 600 mm Dark Shades

12mm cement plaster 1:3 (1 cement : 3 fine sand)

Wall painting (one or more coats) with plastic emulsion paint of approved brand and manufacture on old work to give an even shade.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Painting one or more coats of acryllic exterior paint of approved brand and manufacture(Such as Dulex/ Asian Paints/ Sherwin Willians) on old work including cleaning the surface with water etc. complete.

Painting (two or more coats) with black anticorrosive bitumastic paint of approved brand and manufacture on new work to give an even shade.

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleats with C. P. brass screws and washers.

Providing and fixing brass bib cock (heavy) of approved quality :

15 mm nominal bore

Providing and fixing C.P. bras or M. I. Trap for wash basin and sinks:

32 mm dia

Providing and fixing brass stop cock (heavy) of approved quality :

15 mm nominal bore

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality :

20 mm nominal bore

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996.

1000 lit. Capacity

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:

110 mm dia

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door :

100 mm dia

Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door :

110 mm dia

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 pipe).

15 mm outer dia CPVC pipe

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 pipe).

20 mm outer dia CPVC pipe

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work.

SCH-40(blue)/(white)

32mm outer dia.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 including cutting of stone and making good the walls wherever required : Kitchen sink with drain board with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete

Overall size 1040mmx510mm (41"x20") bowl size 460mmx410mmx200mm (18"x 16"x 8") depth 200 mm. Glossy. 1.0mm thk,

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm

Jet Black

Providing and laying 20mm thick cuddapah in shelves over 20 mm thick base of cement mortar 1:3 complete

Providing 25 mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer-in-charge

Making soak pit. 2.5 m dia 3 m deep with 45x45 cm dry brick honey comb shaft and S.W. drain pipe 100 mm diameter, 1.8 m long complete filled with laterite stone aggregate 125 to 180 mm surrounded by laterite stone aggregate of 40 mm and down gauge as per standard design.