ADDITION / ALTRATION OF BUILDING NO P-64, P-65, AND P-71 AT ARTY CENTRE UNDER GE NASHIKROAD CAMP

Amount

Dismantling of brick work or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillers etc ashlar facings, dressed stone work and precast concrete articles without disturbing to adjoining structures

Demolition of reinforced cement concrete above ground floors exc 15 cm thickness as in roofs,floors,beams and staircases,landings chajjas and similar suspended works(cutting of reinforcement as required to facilitate demolition sahll be included in the rate)

Dismantaling of stone slabs of any description or thickness in floors, aprons etc laid bedded & pointed in any mortar complete all as specifed and directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises.

Demolition of cement concrete (un reinforced) of any description and in any position not otherwise specifically provided for.

Taking down cement or cement lime plaster on brick or stone walls etc including racking out joints hacking for key scrubbing down with water etc & removing rubbish out side MD land all as directed.

Excavating in trenches,n exc 1.5 m wide and n exc 1.5m in depth for foundation etc in any type of soils

Returning filling in, including spreading, levelling , watering & well ramming in layer n exc 25 cm as in soft/loose soils

Removing excavated material (soils) n exc 50m & depositing where directed at a level n exc 1.5m above the starting point.

M&L for Hard core of gauge n.exc 63mm deposited spread levelled in layers n.exc 15cm thick watered and rammed to a true surface using broken stones boulder complete all as specified and directed.

M&L for PCC 1:4:8 Type D2 (40 mm graded aggregate)as in foundations,filling and mass concrete

M&L for reinforced cement concrete of M-25(Design Mix) in footings,foundation beams and plinth beams

ditto as Item no 12 above but in columns

ditto as Item no 12 above but in beams and lintel beams over 1.5 m span.

ditto as Item no 12 above but in slabs supported on walls, beams and columns in floors, roofs, landings etc.

M&L for Mild steel TMT bars of 10mm dia and over,cut to length,bent to shape required,including cranking,bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L TMT bars 6 to 8mm mm dia and over cut to length bend to shape required including cranking, bending, and binding with mild steel wire (annealed) not less than 0.9 mm dia.

- ditto - but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders.

M&L for formwork to sides of concrete foundations,footings and plinth beams for flat rough finished surfaces of concrete

M&L for formwork to soffits of suspended slabs such as roof slabs for flat rough finished surfaces of concrete

M&L for formwork to sides of soffits of floor or roof beams,cantilevers,lintels etc for flat rough finished surfaces of concrete

M&L for formwork to sides of pillars,columns for flat rough finished surfaces of concrete square,rectangular or polygonal

M&L for formwork to rough finished surfaces of concrete as in edges of concrete flats n exc 20cm wide

M&L brick work with Fly ash bricks straight or curved on plan exceeding 6 mtr mean radius built in cement mortar 1:6

M&L brick work withFly ash bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4

M&L for rendering 15 mm thick cement plaster (double coat 10mm base coat + 5mm thick finishing coat ) on than fair faces of brick work or concrete surfaces in CM 1:4 rendering is to be finished even and smooth without using extra cement adding water proofing compound 3% by weight of cement (water proofing compound shall be measured and paid separately)

Supply of integral water proofing compound

M&L for cement concrete 1:3:6 Type C1(20 mm graded aggregate) as in plinth protection 75mm thick, finished even and smooth without using extra cement, joints in bays shall be filled with mastic filling comprising 1 part of heated bitumen 85/25 or 90/100 grade and 3 parts of sand (all by weight) complete all as directed.

M&L for rendering 15 mm thick on stone masonry surfaces or surfaces other than fair faces of brick work or on one side of lathing in cement mortar 1:6 & finished the surface even & fair without using extra cement all as specified.

M&L for 5 mm thick rendering in CM 1:4 on ceiling surfaces and rendering is to be finished including one coat of wall care putty all as directed .

M&L for cement concrete type D-2 1:4:8 (40 mm graded aggregate) under floors/sub base

M&L for cement concrete type B-1, 1:2:4(20 mm graded aggregate) 30 mm thick as in floors etc.

M& L moorum/ red bajri filling in floors or pavings,laid in layers n exc 15 cm thick ,spread,levelled and rammed including watering

M&L non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile over and including 15mm thick cement screed bed in CM 1:6 all as directed Engr-in-Charge (The tiles shall be matt finish , shade of the tile shall be as approved by the GE and as per the latest catalogue of the Manufacturer)

M&L glazed coloured ceramic tiles 300 x 450 x 7-8mm thick over and including backing coat 15mm thick in cm 1:4 on vertical surface such as skirting , dados and risers to steps etc. (Tiles shall be approved by the GE and as per the latest catalogue of the manufacturer)

M&L for machine cut kota stone slab 20-25mm thick over 20mm thick cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed. Note: screed bed layer shall be measured and paid seperately

M&L for machine cut Kota stone slab 15-18mm thick in riser of steps, skirting, dado and pillar laid over backing coat and jointed with pigment to match the shade of the slab including rubbing and polishing complete

M&L for hand cut cudappa stone slab 16 -18 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete Note: screed bed layer measured seperately complete all as specifed and directed

M&L granite (of any type)work (table rubbed and polished) 18 mm thick in steps,jambs,pillars, platforms,shelves and like over cement mortar screed bed in CM 1:6 incl pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite

M&L for heavy duty high traffic pavement tiles 10 mm thick of size 600X600 mm over cement mortar screed bed, laid and jointed with gray cement and pointed with coloured cement mixed with pigment to match the shade of tiles complete all as specifide.(Screed bed shal be paid separatly.)

ditto but as in skirting, steps etc in vertical surfaces

M&L screed bed or bedding layer 10mm thick in cement mortar (1:4) on or concrete surfaces

M&L for 20mm thick Screed bed or bedding layer in CM 1:6 for laying floor finishes

M&L for 15mm thick rendering in CM 1:4 as backing coat

Rounding to edges of stone slabs one edge and including making 6-7 mm thick double line anti skidding grooves wherever necessary such as in steps, platform, shelves and other similar work

M& L for Cutting out concrete blocks, slabs, brickwork or stone masonry (in alter nate course), forming tooth-ings for and bonding new work using precast cement concrete bolcks type B1 1:2:4 ( using 20mm graded stone aggregate) set in cement mortar 1:4 into old work, including new materials entering old wall all as specified and directed by Engr-in-charge

Taking up or down tubes galvanized iron and connections and removing/shifting from site incl cleaning for refixing where directed complete all as specifed and directed

(a) 25 mm dia

(b) 20 mm dia

(c) 15 mm dia

Re-fixing only tubes galvanized iron and connections fixed to walls or laid in floor supplying & fixing new fittings such as socket, bends, elbows nipple, union etc all as specified and directed of size complete all as specified and directed

(a) 25 mm dia

(b) 20 mm dia

(c) 15 mm dia

S/F for tubes medium grade, galvanized with iron all fittings fixed to walls, ceiling and laid in floor of sizes complete all as specified and directed :-

(a) 25mm dia

(b) 20 mm dia

(c) 15 mm dia

S&F in repair vitreous china urinal flat back snow white including grating, spreader and union and discharge pipe complete all as specifed and directed (Make ISI marked : Cera - CARMINA Cat No. S4020102/Hindware-Starwhite cat No 60002/Parryware-New Magnum cat No C-0575)

S&F for waste fittings,brass,chromium plated 40 mm dia for urinals

M&l marble work 18-20 mm thick Makrana white (table rubbed and polished) in steps, jambs, pillars, window cills, coocking platforms, floors, and like laid and bedded in gray cement pointed with white cement 1:2 using marble dust and pigment to match with shade of marble complete all as specifide and directed by Engineer in Charge.

S&F in repairs bib taps standard of PTMT 15mm bore dia any colour high presure screwed for iron pipe (minimum weight 90 gms) complete all as specified and directed

M&L for Disconnecting existing tanks,setting aside(or lowering if required)for repairs,cleaning,etc and hoisting if required reconnecting and refixing in position.

S&F in repairs Ball brass valves, high pressure, with polythene float and flynut for 25 mm bore dia pipe complete,screwed for iron pipe or brass ferrule and fixed

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 ltr ISI Marked of approved make.

S&F in repairs Gun metal,globe or gate valves,with iron wheel head,screwed both ends for 20mm bore iron pipe and fixed

Dismantling of PVC rain/vent/ waste pipe any bore

S&F PVC (SWR) pipe single socketed 110mm bore any length with rubber ring joints fixed to wall complete all as specified & directed bore of pipe in mm complete all as specifed and directed

S&F of PVC(SWR) bends of any radius

(a) 75 mm bore

(b) 110 mm bore

S&F of PVC(SWR) branch piece,single(single Y) equal or unequal

(a) 75 mm bore

(b) 110 mm bore

S&F of PVC(SWR) junction single,(single T),equal or unequal

(a) 75 mm bore

(b) 110 mm bore

S&F of PVC(SWR) branch piece,Double (Double Y) equal or unequal

(a) 75 mm bore

(b) 110 mm bore

S&F of PVC(SWR) junction Double ,(Double T),equal or unequal

(a) 75 mm bore

(b) 110 mm bore

S&F of PVC(SWR) 'P' trap of 125/110 mm bore

Blank

S&F of PVC(SWR) vent cowl of 110 mm bore

S&F of PVC(SWR) vent cowl of 75 mm bore

S&F Vitreous china squatting pan ,'Orissa' pattern, size 580x440 mm snow white,with integral foot rests including P trap.( Make ISI Marked: CERA -Calina Cat No S3010102& S9030101/Hindware- Eco Cat No20042/Parryware Cat No C-0117

S&F in repair stainless steel sink made of stainless steel 1mm thick with out drainage board including plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing contilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size410mmx330mmx160mm complete all as specifed and directed

S&F counter wash hand basin vitreous china ( Snow White) of size 560 x 400 mm incl CP waste coupling, waste pipe brackets (Make: Cera ( Snow White Cat No. S2030103) / Hinware (White Cat No 10017)/ Parryware (Leeds N Over countertop Cat No C-0483) complete all as specified and directed by Engr-In-charge

S&F CP pillar tap with extended body Make Cera-TWISTER series (Cat No. F9010101 ) or Jaquar (Cat No 83011) complete all as specified and directed

S&F in repair cast iron Nahani trap with grating including jointing to waste pipe fixed in cement concrete type (1:2:4) B-1 dia of outlet 75mm complete all as specifed and directed

S/F PVC connections 15mm size with PTMT nuts of length 300mm.

S&F in repair stop valve, 15mm bore dia PTMT of any colour high pressure screwed for iron pipe and fixed (Minimum weight 90 gms) complete all as specified and directed

S&F for Low density polyethylene pipes of Bore 40 mm of pressure rating 6 kgf/cm2 fixed complete to walls ,ceilings or in floors

S&F PVC(SWR) floor trap,plain with grating including jointing with solvent cement

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required.

M & L for reinforced concrete pipes class NP-2 and of dia 150mm bore of pipe laid and jointed complete with collars (RCC pipes shall be of approved make with ISI mark as approved by GE)

Drilling and tapping of exisisting CI water mains in position for branch connection of internal dia 20 mm

M&L for providing precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded aggregate) set in CM (1:6)as in landings, manhole covers etc complete all as specifed and directed

M&L PCC 1:3:6 type C1 (using 20mm graded aggregate as in surface channels and drains including necessary form work complete all as specifed and directed

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in coping including necessory formwork.(straight or curved)

Repairing broken edges of RCC chajjas, roof projections, fins, facia and similar works by dismantling of loose and damaged/ disintegrated portion of edges (cross sectional area not exceeding 150 sqcm) and making good with cement mortar 1:4 or cement concrete 1:1½:3 type A0 and chicken wire mesh with nails (to hold fresh mortar/concrete) including necessary formwork etc. and scaffolding for work upto four storied buildings and finishing the surface by white wash or cement base paint to match the surface with existing work.

M&L for special treatment to sunken portion with 10 mm thick plaster in CM 1:4 with WPC liquid conplast 421 and applying one coat each of Nitoproof 100 & Nitopro 120 on plastered surface . Rendering again 10 mm thick plaster in CM 1:4 mixed with complast 421 in sunken portion of WC & CI/PVC pipes joint shall be filled/jointed with mixture of cement fine sand and nitoproof 130 and provided hole in the wall & fixed 600 mm long 20 mm dia spout light grade & 1:3:6 C2 filling , floor area of wc upto 1.5 Sqm etc complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) fromwooden frame metal frame inculding punching or drilling out old glazing pins / spring clips

S&F Sheet glass ordinary quality 3 mm thick not exc 0.5sqm each pane complete all as specifed and directed

-Ditto- above item No.88 but exc 0.5 sq. m in each pane

S&F 3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square n. exc. 0.5 Sqm in each panes.

S&F 5.50mm thick Sheet glass, ordinary quality and glazing with aluminium beading and size n exc 0.5 sq. m in each pane as specified and directed

M & L for screed bed or bedding layer 15mm thick in cement mortar 1:6 for laying floor finish

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm fixed with stainless steel wire stapples complete all as specifed and directed

S & F Solid PVC frame of size 50mm x 95mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, with necessary arragement for fixing of glass for louvers type window/ventilator and additional PVC beading around the frame for fixing of wiremesh, S & F in opening all as specified and directed by Engr-in-Charge

Taking down shutters of window any description n.exc. 1.00 Sqm each removal from site by contractor at his own expense complete all as specified & directed.

All as per item No.95 above but exc. 1.00 Sqm and n.exc. 2.00 Sqm each

Taking down chowkat or frames with shutters (without taking off shutters from the frame not exc. 1.5 Sqm each &removing from site

All as per item No.97 above but exc. 1.5 Sqm and n.exc. 4.00 Sqm each.

S&F II nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed to walls complete all as specified and directed.

S&F Flush door shutters,30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F (IInd class hard wood) Glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (divided in to square with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mi-tred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Sec-tion 8, cla-use 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

ditto- all as above item no.101 but thickness of shutter 30mm for windows and ventilators etc complete as specified in SSR Part-I Section8, clause 8.24 (b) all as specified and directed.

S&F 100 mm Butt hinges,medium weight cold rolled stainless steel all as specified & directed.

S&F stainless steel butt hinges 75mm size medium weight complete all as specified and directed

Ditto as per item No.104 above but fixed in repairs

S&F MS barrel tower bolts stove enameled black with bright bolt – 150mm long fixed complete all as specified and directed.

Ditto as per item No.106 but fixed in repairs

S&F MS sliding door bolt plate type, stove enameled black with bright bolt not less than 12mm dia with and incl. a minimum of 6 bolts and nuts,four on bolt plate and 2 on staple plate – 300 mm long complete all as specified and directed.

Ditto as in item No. 108 but fixing in repair

S&F MS pressed handles oval type stove enameled black fixed – 125mm size complete all as specified and directed.

Ditto as item No.110 but fixing in repair.

S&F floor door stopper of aluminium alloy body & tongue, anodised, with hard drawn steel spring of 140mm size fixed in floor complete all as specified and directed.

M&L for spot welding in repair for MS work, trusses ,etc. each continous run of weld not less than 100mm in length including necessary scaffolding upto the height of 10 metre and including safety measures at site as directed by Engr In Charge

S&F aluminium alloy barrel tower bolt 150 mm long

S&F 150 mm aluminium alloy handels cast/plate type

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L Preparation of old/ previously treated or untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint)

M&L for two coats of synthetic enameled paint over a coat of red oxide including prepration of new steel or steel bases surfaces of any description over 10cm in width or girth all as specified

-ditto- all as per above Item No. 119 But one coat on old steel surfaces

-ditto- All as per above Item No. 119 but n.exc 10 cm in width or girth.

-ditto- all as per above Item No. 120 But one coat on old steel surfaces

M&L for preparation of newly plastered or unplastered , concrete surfaces and applying three coats of white wash all as specified and directed

M&L Preparation of new plastered surfaces and applying two coats of white wash on ceiling surfaces all as directed

M&L for complete removal existing treatment, washing rubbing down and applying twocoats of oil bound distemper over a coat of chalk whitening including Birla White wall care putty on wall surfaces complete all as specidfied and directed.

M&L preparation of old decorated plastered or unplastered surfaces, brooming down moulds and efflorescent salt and trading oil and greasy spot and applying one coat of white wash on walls.

All as per item No .125 above but on ceiling.

M&L for preparation of old decorated plastered or unplastered surfaces and applying one coat of colour wash on walls

M&L for cleaning of existing wall surfaces including preparation (i.e. brooming down plastered / unplastered surfaces complete) and applying one coat of Acrylic weather proof exterior paint (Make: APPEX of Asian Paint or equivalent) complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of Acrylic weather proof exterior paint (Make: APPEX of Asian Paint or equivalent) including and over one coat of white cement as primer complete all as specified and directed.

M&L for preparing plastered surfaces and applying two coats of oil bound distemper over one coat of primer including preparatory work with including and applying wall care putty to distempering on surfaces of walls.

M & L for preparation, priming of old stone surfaces of walls and applying two coats of white cement including cleaning and removing all dust of stone wall surfaces with watering etc. all as directed by Engr-in-charge

Taking down PVC chowkat or frames with shutters (without taking off shutters from the frame) not exc. 2.0 Sqm each. Complete including removing from site by contractor at his own expense all as specified & directed.

S&F factory made WPC door frame, 100% solid wood plastic composite (WPC) door frame 90mm x 45mm made from wood plastic composite (Single extruded process) material with density 780 Kg/Cum all as specified by manufacturer and directed by Engineer-in-Charge.

S&F 28 mm thick 3-Layer solid PVC flush shutter, 100% solid made from co-Extruded three layer rigid PVC foam sheet (single extruded) with density not less than 600 Kg/Cum outer layer 1 mm thick should be rigid upvc with density of not less than 1400 Kg/Cum all as specified by manufacturer and directed by Engineer-in-Charge.

S&F in repairs SS Peg set of six including fixing with necessary srews and nails all as directed

S&F in repair SS drapery rod 25mm dia plain of good quality, sample as approved by GE and all as specified and directed by Engineer-in-charge.

S&F for SS Brackets fancy type for drapery rod all as specified and directed by Engineer-in-charge.

M&L for providing precast cement concrete1:2:4 type B-1, (20 mm graded aggregate) in cover slabs including chamfers,weatherings,throatings etc and setting in CM 1:4

M&L for cement concrete 1:2:4 Type BO using 12.5 mm graded aggregate for filling up the undulation in floors to maintain slope complete all as specified and directed

Shutters of any description area exc 1 sqm but not exc 2 sqm each resecuring or easing and adjusting without taking down

-ditto-= above Item No. 140 but area exc 2 sqm each

Dismantling single layer Mangalore pattern or similar tiles incl ridges in roofing all as specified and directed.

Dismantling battens for tiles shingles etc of any size incl tilting fillets spaced exc 15cm

M&L clean sawn battens of 2nd class hard wood at 30 cm centres of sectional area exceeding 5 and not exceeding 15Sq cm any position.

S&F Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe-410-0 or Fe -310-0 complete all as specified and directed

S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S & F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutter, drip and straight flashing fixed with sif tapping screws..

Dismantling wall and ceiling boards( Fibre, pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified & directed.

M&L for coloured seamless PVC sheets as in false ceiling of size 3.05m x 0.25m x 8-9mm thick including aluminium grid of "H", "U" & "L" section ( 40mm x 25mm) of 1mm thick in ceiling fixed with screw or solvent cement as per manufacturer's instruction all as directed by Engr-in-charge and as specified by the manufacturer.

S&F Machine pressed precast concrte interlocking with gray cement no pigment paver block any shape and size confirming to IS 15658-2006 of 60mm thick , M-35 Grade, laid over and includding 25 mm thick layer of sand cushioning all as specified & directed by Eng-in- Charge. (Make ISI Marked as approved by GE)

Taking down carefully existing bitumen tarfelt incl. screed and cleaning of surfaces of roof etc. with wire brush incl. flashing and junctions of parapets / kerb walls etc. and removing of the rubbish to a distance exc. 500 metres but not exc. 1.5 km and depositing where directed

M&L for keyed pointing of CM 1:4 to random or polygonal rubble;uncoursed or brought upto course

M&L for polygonal rubble, uncoursed well bonded bedded and solidly hearted built in CM 1:6

Extra over polygonal rubble walling, uncoursed or brought upto courses for hammer dressing to face stones with maximum depression on face from a straight edge held agianst the dressed surface not exc 20mm granite or trap stone all as specified.

S&F in repairs CP shower rose Make CERA ( Cat Part No. F7020501) or Hindware (Cat No F160025) Or Jaquar (Cat No EOS538N) all as directed by Engineer-in-Charge

S&F 4mm dia Plain mild steel wire, galvanised class 3, in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc.

S&F powder coated Anodised aluminium frame, shutters for doors, windows, ventilators with one or more rebates including joining cleats, glazing clips,screws, rubber packing, neopranes, fittings and fixtures etc. complete all as specified and directed by Engr in Charge

M&L for cleaning the newly plastered surfaces of concrete with wire brushes and applying water for washing/cleaning etc on the dried roof surfaces apply one coat of bituminous primer @ 0.2 kg/sqm Laying torch applied APP Polymer modified bituminous membrane 3mm thick not less than 3.50 Kg/Sqm with non woven polyester mat as reinforcement weighing not less than160Gms/Sqm thermo fusion process & one coat of alluminum paint 0.15 kg/Sqm

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc (Note - Old serviceable switch/socket/regulater/switch-socket shall be taken on charge for reuse)

Taking down carefully by unscrewing from boards / outlet boxes, fitting and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carring to the store (To be measured only when found serviceable in all respects complete for reuse)

Dismantling unserviceable main switch/DBs with MCBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surfaces.

Material and labour for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC casing caping and accessories surface on wall / roof / floor etc, ISI marked with valid CML No.(IS-9537-1983 for PVC casing caping and IS:3419:1976 for accessories), with mild steel / pressed steel sunken boxes (with earth dolly) duly painted with two coats of anti corrosive paint / aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:- MAKE OF CABLE - STANDARD/ PLAZA / HAVELLS/POLYCAB/FINOLEX & MAKE OF PVC CASING/CAPING - PRICISION/PRESSFIT/MODI

(a) One light point controlled by one, one way switch

(b) One ceiling /exhaust fan point controlled by one switch and regulator

(c) One 3 pin 5 amp socket out point on the same board with other switches.

(d) One3 pin 5 amps socket out let point on independent board

All as per same in item No 164 above but for one socket outlet 15 amp on independent board with 2.5 Sq. mm cable and 2.5 Sq.mm. earth wire.

S & F Switch piano flush type single pole one way 5 amps.

S & F Socket out let 2 in one, 5/3 pin 5Amp

S & F Switch socket combination 5 Amps 5 pin flush type

S & F Switch socket combination 5 in 1, 5 pin 5/15 Amps flush type universal .

S & F Ceiling rose, surface bakelite 65x50 mm three terminal

S & F Electronic regulator 120 Watt step type

S&F in repair 20 Watt Batten (4 feet) suitable for LED T8 lamps decorative luminaire designed for LED Tube comprises of CRCA pre coated housing with two colored plastic End cap. Crompton Cat Ref : DMLN1LT8-16 , Havells Cat No: REGALBATTENT 8UPTO1X22WDSBSWH, or eqvt of Bajaj/Philips.

S&F 20 Watt LED Tube Light (4 feet) comprises of extruded Strip in thermally conductive material & extruded housing in Optically efficient material milky white with inbuild split LED driver at the end of LED tube & FR grade engineering plastic End. Make : Crompton Cat Ref :LT8-20-865-2, Havells Cat No: CRYSTAL 1213T8DSTL20WLED865SGLASS or eqvt of Bajaj/Philips.

Refixing of serviceable tube lighting fitting any type/size. (Note : Serviceable fittings obtained from item No 160 above will be reused.)

S & F 15 Watt LED streetlight fitting luminaire comprises of pressure die cast aluminium housing powder coated in silver grey and toughnedglass. This luminaire is recommended for illuminating access roads, Garden ways, small streets etc. IP65 protection , including coneecting up with 2/3 core flexible coppper conductor cable , compete all as specified and directed by Engr-in-Charge. Make : Crompton Cat Ref : LSTS-15-CDL, Havells Cat Part No- ENDURAPEARLSL15WLED757SASYTOPC or equivalent of Wipro / Bajaj / Philips)

Fabrication ,supply & fixing of GI pipe bracket up to 40 mm dia- 0.9m long & 2 set of clamps made out of 30x5mm ms flat & fixed with anchor bolt suitable for LED security light fitting of any size and type.

S & F 4 way MCCB powerline vertical DBs in double door suitable for TP/FP MCCB SKB 1/2 as incomer bus bar with current rating capacity upto 250A, complete all as specified and directed by Engr-in-Charge, of make Standard Cat Part No-DSDLVDRBAOFO04, Legrand, Cat part No. 5077 25, or eqvt of L&T/Havells/ABB.

S & F MCB DB made of sheet steel, powder painted with bus bar 200 A, neutral link, earth bar and Din rail , 240Volts SPN with 4 way Double door IP-43-IK09 protection grade. (Make : Standard, Cat No. DSDNSHODIW04 / L&T Cat. No. LTSD04GN/ / Legrand Cat No.- 607710 / equivalent of ABB / L&T / Havells)

S & F MCB DB made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, earth bar and Din rail ,240Volts SPN with 8 way Double door , IP-43-IK09 protection grade. (Make : L&T Cat No.-LTSD08GN/ / Legrand Cat No.-607711 / equivalent of ABB / L&T / Havells)

Note for item No. 176 - 178 : (1).The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall. DB to be fixed on wall including frame made out of MS flat 40x5mm. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface (3) Make of DB & MCB - Standard/Legrand / ABB / L&T/Havells (4) (Note : Rate is inclusive of cutting chases & flush to wall & making good to the disturbed surfaces of walls etc to macth with existing surfaces including white washing/colour washing/distempering to match with existing wall/floor/ceiling finishes making good disturbed surfaces of walls, etc )

Supply and fix in repair for MCB SPN 240 Volts, 'C' series, breaking capacity 10 KA of rating 6-40 Amps (Make: Legrand/ABB/L&T/Havells/Standard)

Supply and fix in repair for MCB SP 6-32 Amps 'C' series, breaking capacity 10 KA of rating (Make: Legrand/ABB/L&T/Havells/Standard)

S & F in repair MCCB TPN 63 Amps , 415Volts, 25KA ,4 pole, (Make - Legrand , Cat Part No. 4200 53, or equivalent of Havells/Standard/L&T/ABB)

Taking down ceiling fan / Exhaust Fan of any size or make.

Hanging only ceiling fan 1200mm Sweep by providing fan hooks in proper manner and making connection withT 3 core copper cable including painting all as per specified and directed.

Supply & fix heavy duty exhaust fan 450 mm sweep metallic type including 3 core copper cable & cutting holes if required etc. Make - Havells Cat Part No-Turbo Force SP 1400 RPM or eqvt in Bajaj/Usha/Crompton/Orient.

M & L for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through and including PVC casing caping / conduit not less then 32mm dia medium grade fixed on walls / roof / floors all as directed. (Note ; Two wires of 6 sqmm and one wire of 6 sqmm for earthing and one run of PVC casing caping / conduit shall be measured as one unit.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in gound (Earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connecting to the galvanised iron earth lead wire of 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and earht strip protected by provision of GI light grade pipe 15 mm light grade bore including provision of pit in PCC (1:2:4) type B-1 using 20 mm graded of stone aggregate with PCC cover including 20mm bore pipe for wetering perforated at bottom 1.75 mtr long placed on top edge of earth plate common salt and charcoal (not less than 40 Kgs, 80 Kgs each) filling with fixing arrangement funnel wire mesh and earth work in hard dense soil returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electircal plate No 03 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion.

Samruddhi Construction

M/S G.S RAWAL

AGRAWAL ASSOCIATES

SHYAM CONSTRUCTION

M/s M R MAHANA