CLEAN/ REPAIRS TO SEWAGE LINE, SEPTIC TANK, MANHOLES, GULLY TRAPS AND DRAINS, REPAIR TO PLASTER WORK, ROOF SHEDS, STRUCTURAL REPAIRS, ATT, WELCOME MAINT AND CAMOUFLAGE PAINTING, REPAIR/REPL OF INT ELECTRIC WIRING AT MADH ISLAND UNDER GE AF THANE

Amount

M&L for cleaning/clear of blockage of manholes, gully traps, floor traps, vertical soil/waste pipe of different dia and sewage line in the area of AF station Mumbai (Domestic and Tech area) by providing and deployment of 02 (TWO) Nos of Labours per day excluding Sundays and Holidays. Note : a) The labour (02 nos) will report daily at 0845 hrs on all working days excluding Sundays and holidays at complaint cell centre to attend complaints given by Engr -In- Charge . Complaints needs to be cleared within 24 hrs after receiving the complaints. The contractor will deploy requisite labour and supply all T&P ( mechanical Iron rods, knot ropes , bamboo etc.) scaffolding ladders any other materials required to clear the blockages at the site without any extra cost .Labour for cleaning of sludge from sewage lines (any dia) to manhole is included in quoted rates. In case any labour does not report to Engineer In Charge for the whole day or found missing more than half an hour on any day, Panel recovery @ RS.900/- per head per day shall be made proportionally from contractor's dues. b) The recovery will be made from the contractor @250 Rs per complaint which are not cleared within 24 hrs from the date and time of receipt of complaints. Decision of Engr-In- Charge is final in this respect. Two persons will be provided by the contractor at site. The above item includes conveyance cost of labour with their tools to travel from pocket to pocket to attend complaints including removal of sludge from the site outside MOD land to a distance not exc 5km (The department shall not be liable to provide any kind/form of transportation to the labour). (c) Registers of labour attendance and complaints slips shall be maintained by contractor at their own cost, which shall be kept in the custody of MES Department(complaint cell) duly signed by contractor's representative ,JE(civil) and Engineer in charge.

Opening of cover, de-watering and taking out sludge from septic tank of any size and removing sludge out side MD land and cleaning the septic tank as per BMC rules and placing cover in original position, complete all as specified and directed by Engr-in-Charge.

Excavation in trenches n.exc 1.5 m width and not exc 1.5 m in depth for drainage and getting out in hard dense soil, complete all as specified.

Retuning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm and directed by Engr-in-Charge

M&L for Cement Concrete Type D-2 1:4:8 in foundation filling in mass concrete, ,complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , complete all as specified and directed by Engr-in-Charge.

M&L for providing precast cement concrete type B1 1:2:4 (20mm graded stone aggregate) in apex stones,etc including chamfers, weatherings throating etc and setting in mortar 1:4 (for manholes etc.), complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc., complete all as specified and directed by Engr-in-Charge

Supply only integral water proofing compound, complete all as specified and directed by Engr-in-Charge.

M&L for brickwork with subclass 'B' brickwork straight on plan exc 6m mean radius with old SIze bricks built in CM 1:4, complete all as specified and directed by Engr-in-Charge.

M&L for cutting holes in bricks walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar or cement concrete 1:2:4 type B1 as required exc half brick but not exc one brick , complete all as specified and directed by Engr-in-Charge.

M&L for 2nd class hardwood (SAL) plain, solid, straight chowkats and frames, wrought frames rebated on the solid, reunded or chamfered put together with glue pinned at joints , complete all as specified and directed by Engr-in-Charge.

S&F 2nd class hard wood 30mm thick glazed and skeleton shutters to chowkats, open, rebated and prepare to reveive glass, guage etc (with sash bars any numbers) edges of framing plain chamfered or rounded, fitted with out mitred beads for securing glass etc, size of members of shutters as specified supplied and fitted to chowkats , complete all as specified and directed by Engr-in-Charge.

S&F 2nd class HW 35 mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats,complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames n.exc 1.5 sqm with shutters without taking off shutters from the frame, complete all as specified.

Taking down chowkats or frames exc 1.5 sqm & n exc 4 sqm with shutters without taking off shutters from the frame, complete all as specified.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm each, complete all as specified.

Resecuring or easing & adjusting without taking down shutters of any description exc 1 sqm but n.exc 2 sqm, complete all as specified & directed

Resecuring or easing & adjusting with taking down shutters of any description exc 1 sqm but n.exc 2 sqm, complete all as specified & directed

Resecuring or easing & adjusting without taking down shutters of any description exc 1 sqm and n.exc 2 sqm, complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Squar tube, suppling & fixing in opening as per specification ,complete all as specified

S&F 150mm long aluminium anodized barrel tower bolts of extruded section, complete all as specified.

S&F as in repairs 150mm long aluminium anodized barrel tower bolts of extruded section, complete all as specified.

S&F Aluminium alloy, anodised, sliding door bolt ,300mm length with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed , complete all as specified.

S&F in repair,aluminium alloy anodized sliding door bolt, 300 mm length with hasp & staple (bolt type) and fixing clíps of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified.

S&F 100mm size Butt hinges, extruded stainless steel hinge pin, anodised and fixed, complete all as specified.

S&F as in repairs 100mm size Butt hinges, extruded stainless steel hinge pin, anodised and fixed, complete all as specified.

S&F 30mm width of flaps continuous (piano) hinges mild steel, bright finish or electrogalvanised, complete all as specified & directed

S&F as in repairs 300mm mild steel helical door spring including roller plate complete all as specified and directed

S&F aluminium extruded alloy handle fabricated type anodized 150mm long, complete all as specified.

S&F as in repairs aluminium extruded alloy handles fabricated type anodized 150mm long, complete all as specified.

S&F as in repairs curtain rods mild steel, chromium plated with fixing brackets, stops, rollers etc including brackets, complete all as specified.

S & F in repairs Curtain rods, anodised aluminium alloy with fixing brackets, etc. complete all as specified.

S&F as in repairs Aluminium anodised Tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, 140mm overall length of cover plate, complete all as specified.

S&F as in repairs 100mm length of Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn rubber at bottom, fixed in doors, complete all as specified

S&F in repairs aluminium body door closer hydraulically regulated designation No 3 universal type, suitable for door shutter of 851mm to 1000mm in width and wt. between 61 to 80 kg, complete all as specified.

S&F as in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples ,complete all as specified.

S&F as in repairs double action floor spring hydraulically operated made up of miniumum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty ,complete all as specified.

S&F MS bands, straps, supports of stays, hold fast, wall ties etc and similar articles etc confirming to Fe-410-310m ,complete all as specified.

M&L for TMT steel bars 6mm dia to 8mm dia & over cut to length bent to shape required including cranking bending spirally for hoping for columns and binding with MS wire not exc than 0.9mm dia. ,complete all as specified and directed by Engr-in-Charge.

S&F Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type , including taking down old shutter , complete all as specified and directed by Engr-in-Charge.

S&F as in repairs Plain black mild steel sheet of 1.00 mm thick as in hood of the rolling shutter all as specified and directed by Engr-In-Charge.

S&F as in repairs Prelaminated particle board 18/19mm thickness, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work , or for cup board shelves, complete all as specified.

M&L for machine cut cuddappa stone slab 20 to 25 mm thick pre-polished as in cills/jambs/soffits of window & in door openings in one length, in shelves, etc, set jointed and pointed in cement mortar 1:4 and slurry with grey cement slurry mixed with pigment to match the shade of the slab, complete all as specified

M&L for 40mm thick cement concrete type B-1 (1:2:4) by using 20mm graded stone aggregate as in floor, complete all as specified

Dismantling floor hearth or wall tiling including cement morter bedding (but not backing) and subbish of premisses, complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster on brick/stone or concrete surface including racking out joints, hacking for key, sorubbing down with water to receive plaster, including removing debris/rubbish materíals off the site ,complete all as specified and directed by Engr-in-Charge.

S&F ordinary sheet glass 3mm thick and glazing with oil putty/beddings in square n exc 0.5 sq, in each panes complete all as specified and directed by Engr-in-Charge.

S&F ordinary sheet glass 4mm thick and glazing in aluminium frame work, complete all as specified

S&F for ordinary sheet glass 4.8mm thick and glazing with oil putty/beddings in square exc 0.5 sq, in each panes , complete all as specified and directed by Engr-in-Charge.

S&F figured glass 3mm thick and glazing in aluminium frame work , complete all as specified and directed by Engr-in-Charge.

Hacking out broken glass any thickness size and quality or description form wooden, concrete, aluminium steel frames glazed with oil putty fixed with nails, complete all as specified

M & L for preparation of new treated steel surfaces of any description over 10 cm width & girth not otherwise described and applying two coat of epoxy paint over a coat of primer complete all as specified and directed.

M & L for preparation of old treated wood surfaces of any description over 10 cm width & girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces and apply two Coats of Synthetic enamel paint over a coat of pink primer, complete all as specified.

S&F GI tubing 20mm dia bore, medium grade including all fittings fixed in floor/ walls/ ceilling etc , complete all as specified.

S&F GI tubing 15mm dia bore medium grade including all fittings fixed in floor /walls / ceilling etc, , complete all as specified.

Taking up or down steel tubing and connections 20mm bore, including cleaning for re fixing or removal to store, complete all as specified.

Taking up or down steel tubing and connections 15mm bore, including cleaning for re fixing or removal to store, Complete all as specified.

S&F as in repairs 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed , complete all as specified.

S&F in repair 15mm bore Chromium plated stop valves, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified.

S&F 20mm bore dia ball brass valve, high pressure, with ploythene float and flynut complete, screwed for iron pipe or brass ferrule , complete all as specified.

S&F as in repairs PVC connections 15mm size with PTMT nuts of length 450mm, Complete all as specified

S&F Stack clamps for 75mm bore of pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or root, complete all as specified

S&F Stack clamps for 110mm bore of pipe out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or root, complete all as specified

S&F in repair PVC SWR pipes 110mm dia, single socketed, in any length with rubber ring joints laid in trenches or in floors , complete all as specified and directed by Engr-in-Charge

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors and fixed as in repairs, complete all as specifled.

S&F in repair, 75mm bore PVC (SWR) pipes single socketed, in any leength with rubber ring joints, fixed to walls and fixed, complete all as specified

S&F,in repair, 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls and fixed , complete all as specified

S &F in repair PVC SWR bends of 110mm bore, complete all as specified and directed by Engr-in-Charge

S & F in repair 75 mm PVC(SWR) bends of any radius, complete all as specified and directed by Engr-in- Charge

S & F in repair PVC SWR branch piece single Y equal or unequal for 110 mm bore dia, complete all as specified and directed by Engr-in-Charge.

S &F in repair PVC SWR branch piece (doule Y) equal or unequal 75 mm bore dia , complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) Nahani trap plain of dia 75mm with grating including jointing with solvent cement ,complete all as specified and directed by Engr-in-Charge.

M&L as in repairs 75mm dia of outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified

S&F as in repairs PVC (SWR) floor trap plain of 75mm outet Dia with grating including jointing with solvent cement, comple all as specified and directed

M&L concrete bed of cement conorete 1:3:6 type C2 (using 40 mm graded stone aggregate) to drain pipes including packing under, and hunching against the sides of pipe after they are laid and tested for bore of pipe is 150mm ,complete all as specified and directed by Engr-in-Charge.

M&L Concree bed of cement concrete 1.3:6 type C2 (using 40 mm graded stone aggregate) to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for bore of pipe is 100mm ,complete all as specified and directed by Engr-in-Charge.

S&F 150mm dia Reinforced concrete pipes, class NP2, laid and jonted complete with collars laid in trenches and jointed as specified ard directed by Engr-in-Charge, complete all as specified and directed by Engr-in-Charge.

S&F 100mm dia Reinforced concrete pipes, class NP2, laid and jonted complete with collars laid in trenches and jointed as specified ard directed by Engr-in-Charge, complete all as specified and directed by Engr-in-Charge

S&F as in repairs 10 litres PVC valveless, syphonic action type, flushing cistern ,low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified.

Demolition of brick masonary built in cement mortar including all quions, arches, pillars etc but including ashlars facings, dressed stone work and pre cast concrete articles other all as specified and directed by Engr-in-Charge.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc, complete all as specified.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified.

Demolition of reinforced cement concrete of any description as in any position & removing Demolition materials , complete all as specified and directed.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified

Demolition PCC and taking up break/decayed drain pipe (Salt glazed ware, AC or Reinforced concrete) 150 mm dia pipe from Cement mortor and depositing the debries where as directed to a distance exc. 50m ,complete all as specified and directed by Engr-in-Charge

Demolition PCC and taking up break/decayed drain pipe (Salt glazed ware, AC or Reinforced concrete) 100 mm dia pipe from Cement mortor and depositing the debries where as directed to a distance n exc. 50m, complete all as specified and directed by Engr-in-Charge.

Taking down the unserviceable Aluminium glass door shutter of any size and description and refixing the same after resecuring the shutter by using aluminium 'L' section at the joints and refixing the glass in the shutter complete all as specified and directed (Note : All accessories required for repairs shall be measured seperately under other respective items)

Taking down aluminium sliding windows of any description and any size and repalcing the wornout , broken wiremesh, aluminium sections, glass, grill,, rubber beading, rollers, locks, etc as required and refixing back into the same opening for easy movement of shutters including necessary fittings and fixtures ( Note : items such as wirmesh, Glass, grill, rubber beading, rollers, locks, aluminium section etc will be paid seperately under respective items as supply only.

Supply only PVC Star lock for Aluminium windows.

Supply only Nylon / PVC Rollers for Aluminium Windows.

Supply only Rubber beeding suitable for aluminium door/window shutters.

M&L for Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make , complete all as specified and directed by Engr-in-Charge.

S&F in repair Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings , complete all as specified and directed by Engr-in-Charge.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed by Engr-in-Charge.

M&L for machine cut cuddappa stone slab 20 to 25 mm thick as in cills/jambs of window & door openings, set jointed and pointed in neat cement slurry with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete including 15mm thick backing coat in cement mortar 1:4 , complete all as specified and directed by Engr-in-Charge.

M&L for 40mm thick cement concrete type B-1, 1:2:4 ( using 20mm graded stone aggregate) as in floors & finishing even and smooth without using extra cement, complete all as specified.

M&L Coloured Glazed Ceramic tiles 300 x 200 and 6-7mm thick on vertical surfaces such as skirting, dados and risers to steps etc including 10mm thick backing coat in CM 1:4 complete all as specified and directed Note : Tiling work is carried out in patches

M&L non skid ceramic tiles(Coloured) 7 to 8mm thick (square/rectangular) area of each tile exc 0.06sqm but n.exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed 15mm thick in CM 1:6 complete all as specified and directed Note : Tiling work is carried out in patches

M&Lfor rendering 15mm thick in cm 1:6 finished with neeru finish as specified on fair faces of brick work or concrete surfaces , complete all as specified and directed by Engr-in-Charge. Note : Height factor upto15m of watch tower shall be considerd while quoting the rate,nothing extra shall be paid on this account.

M&L for rendering 15mm thick on other than fair faces of brick work/stone surface in cement mortar 1:4 mxed with water proofing compound including finished even and smooth with using extra cement for manholes ,complete all as specified and directed by Engr-in-Charge. Note :- WPC will be measured and paid separaterly.2.Note: Plaster work is carried out in patches n.exc1 Sqm

M&L preparing newly plastered surfaces ,and applying 2 coats of Oil Bound Distemper over a coat of alkali resistent primer on walls , complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old treated plastered or un-plastered surfaces of wall and applying one coat of oil bound distember etc complete all as specified and as directed by Engineer-in- Charge.

M&L for preparation of old treated plastered or un-plastered surfaces of wall and applying two coat of oil bound distember etc complete all as specified and as directed by Engineer-in- Charge.

M&L for preparation of old treated plastered or un-plastered surfaces of ceiling surfaces and applying one coat of oil bound distember on ceiling etc complete all as specified and as directed by Engineer-in- Charge.

S&F in repair bib taps for 15 mm bore, fancy type cast copper alloy chromium plated with crutch or butterfly handle, Screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engr-in-Charge.

S&F as in repairs Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified.

S&F as in repairs Vitreous China wash down water closet pan (pedestal pattern), including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified.

S&F as in repairs vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests , complete all as specified and directed by Engr-in-Charge.

M&L as in repairs Vitreous China wash basin, white, flat back, size 550x400mm and S&F brackets including cutting for and pinning in ends of brackets or erecting stand including waste pipe , 32mm Waste fittings, brass, chromium plated for glazed basins, with long screwed shanks and fly-nuts, flange end bedded in red lead cement, and other end fixed , complete all as specified and directed by Engr-in-Charge.

S&F as in repairs health faucet (ABS Body mild steel chromium plated suitable for 15mm dia pipe with 1.25meter long flexible tube and ABS wall hook including making connectíons and fixed in position , complete all as specified and directed by Engr-in-Charge.

Removing excavated material (Soil) exc. 500m but n exc. 1.50 km distance and depositing where directed ,complete all as specified and directed by Engr-in-Charge.

M&L Granite slab work 18 to 20mm thick in floors steps, platforms, shelves etc and fixed over cuddappa stone by using aerolite adhesive complete all as specified and directed

S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, both face is covered with decorative face veneer with lipping/frame to match

S&F as in repairs Hasp and staple 100mm size mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws, complete all as specified.

S&F as in repairs 125mm size Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified

S&F 100mm size stainless steel Butt hinges 1.75 mm thickness, with matt finish, complete all as specified

S&F as in repairs 100mm size stainless steel Butt hinges 1.75 mm thickness, with matt finish complete all as specified

Taking down aluminium sliding windows of any description and any size and replacing the wornout, broken wiremesh, aluminium sections, glass grill, rubber beading, rollers, locks etc as required and refixing back into the same opening for easy movement of shutters including necessary fittings and fxtures (Note: Items such as i) Wiremesh, ii) Glass, ii) Grill, iv) Rubber beeding, v) Rollers, vi) Locks, vi) Aluminium sections etc will be paid seperately under respective items as supply only)

Supply only PVC Star lock for Aluminium windows

Supply only Nylon / PVC Rollers for Aluminium Windows

Supply only Rubber beeding suitable for aluminium door/window shutters

M & L For cleaning of OH PVC Service Tank internally by bailing out of water/sludge from bottom of sump, removing all scale, dirt, alges and other growths from entire surfaces of tank and from mouths of Circulating pipes by rubbing with wire brushes and by high pressure cleaning method with roatary sets with approved detergents and sucking all dirty water by avaccum cleaners, disinfecting the tank with approved chemical/bleaching powder for making the surfaces bacteria free and cleaning with fresh water, all as direced by Engg-in-charge. (a) Overhead Pvc water tank upto 500 Liters of capacity NOTE- cleaning of OH PVC service tanks are safely to be handled Damage and bracking of tanks are on Contractors OWN risk.

Ditto as per Srl Item No 127.00 above but exc 500ltr and n.exc 1000 Itrs capacity

M&L for rendering 10mm thick CM 1:4 on brickwork or concrete surface of walls and rough cast plaster in whike under coat is in plastic state in the ratio 1:1:1(1 part fine gravel of size between 6 to 12mm, 1 part cement, 1 part coarse sand), and finished even, complete all as specified and directed.

M&L for rendering 10mm thick CM 1:3 on fair faces of concrete surface and finised surfaces even and smooth without using extra cement complete all as specified and directed.

Removal of existing concrete including loose/weak concrete from the concrete structure i.e. beams/ columns/ deckslab etc upto beyond corroded steel reinforcements to a depth of minimum 10mm behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippers including high pressure water jetting and removal of debris. Concrete around the corroded reinforcement shall be removed properly. The edges of the repair locations of concrete should be saw cut to depth of at least 10mm to avoid featheredging and to provide a square edge complete all as specified and directed by Engr-in- Charge. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation.

M&L for Preparation of surface and removal of rust in the loosely bonded concrete of the RCC deckslab, beam / girder and piles shall be chipped out using the mechanical cutter exposing the bars and applying Rust Remover using small brush and allow to react it for 16-24 hrs. Before applying protective coating,the surface should be wire brushed and thoroughly cleaned for dust with dry cloth complete all as per manufacturer instructions and directed by Engr- in- Charge. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation.

M&L for applying two coats of Anti-Corrosive Primer two component (epoxy anticorrosive zinc rich coating) on reinforcement steel surfaces uniformely. Coating shall be applied by the brush to the exposed and cleaned rebars with an interval of 45 minutes to 1 hour @ 40microns DFT / coat and allowed to completely dry for 24 hours complete all as per manufacturer instructions and directed by Engr- in-Charge. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation.

M&L for preparation of concrete surfaces by removing loose concrete, dust, dirt etc, cleaning the surface properly and applying one liberal coat of epoxy bonding agent ( two component agent) by brush application complete all as per manufacturer instruction and directed. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation.

M&L for 50mm thick polymer modified mortar ( average thickness) modified single component, alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortar on conrete structure. Applying the mortar arround the reinforcement and finishing to bring it in line with existing concrete surface complete all as per manufacturer instructions and directed by the Engr-in- Charge. Note :- The contractor Quoted rate should includes necessary scaffolding and form work both for new work as well as for protection of existing structure during rehabilitation.

M&L for preparation of new plastered or unplastered surfaces of walls including scrapping and applying two coats of distemper oil emulsion over a coat of 1mm thick wall care putty, complete all as specified and directed.

M&L for Preparation of new plastered surfaces of wall and apply two coats of Acrylic emulsion exterior paint of required shade : (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) and upto ht of 15m from GL, complete all as specified.

M&L for preparation of new plastered or unplastered surfaces of ceiling and apply two coats of distemper oil emulsion over a coat of 1mm thick wall care putty, complete all as specified.

M&L for preparation of old surface of walls and applying 1 coats of Oil Bound Distemper on walls, complete all as specified.

M&L for Preparation of old wall surfaces and Fiinishing walls with Acrylic Smooth exterior paint of required shade : New work (Two coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) and upto ht of 15m from GL , complete all as specified.

M&L for preparation of old plastered or unplastered surfaces of ceiling and apply one coats of distemper oil emulsion, complete all as specified.

M&L for providing and injecting chemical emulsion for post constructional antitermite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete all as specified.

M&L for providing and injecting chemical emulsion for post constructional antitermite treatment At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same, complete all as specified.

M&L for providing and injecting chemical emulsion for post constructional antitermite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete all as specified.

Dismantling timber scantling in fillets, rails, posts, rafters, purlins etc under 40 sqcm in section, complete all as specified.

Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as pecified.

S&F rolled sections as in main & cross beams , columns/vertical posts, rafters, purlins where connected to common rafters and running rails & any other places with angles cleats or other connected plates, brackets, wind ties etc confirming to Fe 410 -W (Gde-E-250) quality A, complete all as specified.

S&F plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attahment, confirming to Fe 410 -W (Gde-E-250) quality A, complete all as specified.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified.

Supply and fix Pre-painted Galvalume Aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified.

Supply and fix Pre-painted Galvalume Aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to walls/in chajjas, fixed with self tapping screws , complete all as specified.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing , complete all as specified.

M&L for preparation of new Steel surface synthetic enamel paint of two coats in any description, over 10 cm in width or girth, not otherwise described, over a coat of Red oxide, zinc chrome, complete all as specified.

S&F as in repairs PVC coated ultraviolet resistant chain link fencing of any mesh size, including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire, complete all as specified.

M&L for Writing letters or figures (Block, Roman, Italic or Indian) n.exc 30cm high, complete all as specified.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) , complete all as specified.

M&L for 75 mm thick cement concrete type C-2 (1:3:6) as in plinth protection and finishing cement concrete surface even and smooth without using extra cement, complete all as specified.

M&L for 75 mm thick cement concrete type B-1 (1:2:4) as in floor /hard stading and finishing cement concrete surface even and smooth without using extra cement and spike rolling to surface or making impressions of expended metal, while the concrete is green, complete all as specified.

M & L for complete removal of existing treatment on surface of wall etc in any position washing down with water and clearing the surface from all loose dirt, chalk, grease, fungi, algai, flakes etc, and applying two coats of weather proof acrylic paint over a coat of weather proof primer with camouflage pattern complete all as specified and directed by Engr - in - Charge.

M & L for preperation of old surface by bio wash, scrapping and cleaning etc of slope roof of concrete, asbestos cement sheet and applying two coats of weatherproof acrylic paint over a coat of weather proof primer with camouflage pattern complete all as specified and directed by Engr - in - Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Taking down carefully point wiring and removing from site such as (Light,fan socket or power) Complete including fitting and fixtures,fan regulators switch boards,switches,ceiling rose's lamp holder from existing batten PVC conduit/steel conduit wiring complete excluding light fittings and fans all as specified and making good to the disturbed surfaces to match with existing ,complete all as specified and as directed.

M & L for point wiring repair complete for light on independent /combine board with cable 1.5 sqmm (Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC casing & caping, hooks , elbows, juction covers and junction boxes and sinking's for sunken GI terminal boxes Min 50mm deep ,suitable length and 1. 6 mm thickness for mounting, switches, sockets,fan regulator with 3 mm thick plastic laminated sheet cover fixed with cadmium plated screwed and cup washers, duly grouting and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and directed.

Ditto as per Srl item No -164.00 above but for one socket outlet 5/6 amp on independent board complete all as specified and directed

Ditto as per Srl item No -164.00 above but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed

Ditto as per Srl item No -164.00 above but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed

Ditto as per Srl item No -164.00 above but for one light point controlled by two 2 ways switches complete all as specified and directed

Ditto as per Srl item No -164.00 above but for call bell point complete all as specified and directed

S & F in replacement switch piano flush type 5/6 Amps single pole one way complete all as specified and directed.

S & F in replacement switch piano flush type 5/6 Amps single pole two ways complete all as specified and directed .

S&F bell push flush type 5 Amp complete all as specified and directed.

S&F Electronic bell AC 230 Volt single pole ding dong type complete all as specified and directed.

S & F in replacement switch socket combination 5 pin, type 5/6 Amps flush type complete all as specified and directed.

S & F in replacement switch socket combination 6 Pin, 15/16 Amps flush type complete all as specified and directed.

S & F in replacement Socket outlet 5 pin 5 Amps flush type complete all as specified and directed.

S & F in replacement Industrial socket metal clad plug and socket with MCBs single pole 20 Amp complte all as specified and directed.

S & F in replacement modular switch 5/6 Amps single pole one way,one module including modular cover plate with frame and metal flush box complete all as specified and directed .

S & F in replacement modular switch socket combination 5 pin, type 5/6 Amps5 in 1 flush type including modular cover plate and metal flush box with frame complete all as specified and directed .

S & F in replacement modular switch socket combination 6 Pin, 5/16 Amps flush type including modular cover plate with frame and metal flush box complete all as specified and directed.

S & F in replacement modular switch 5/6 Amps single pole two ways including modular cover plate with frame and metal flush box complete all as specified and directed

S & F in replacement modular socket outlet 5 pin 5 Amps flush type including modular cover plate with frame and metal flush box complete all as specified and directed

S&F in replacement modular bell push 5 Amp including modular cover plate with frame and metal flush box complete all as specified and directed.

S & F in replacement modular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete including modular cover plate with frame and metal flush box all as specified and directed.

S & F ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified and directed .

Taking down carefully existing serviceable LED Tubelight/ bulkhead/ security light/ recess mount fitting of any size and refixing the same to respective location after carrying out cleaning all the components of fittings, including replacement of nuts, bolts and connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connectorcomplete all as specified and directed .

S & F in replacement LED Tubelight fitting with aliminium housing and integrated electronic driver, 20 watt having input voltage AC90-300V, 50 Hz , 6500K,surge protection min 4 KVA and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed.

Supply and fixing in replacement LED building security light fitting outdoor type 35 Watt 230 V AC surge protection 10 KVA outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.& Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 1 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed.

S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed

S&F LED lamp 9W for angle holder complete all as specified and directed

S & F timer switch with astronomical timer switch min 8KW, 3 pole, 230 V suitable for street light control including all assessories complete set all as specified and directed.

S & F in replacement LED Water tight bulk head fitting 10 W,comprision of connector galvanised cast iron back plate,weather proof enamelled gallery ,glass well,and including 10 watt LED all as specified and directed.

S&F in replacement LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.all as specified and directed.

S & F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. all as specified and directed.

S & F speed regulator for ceiling fan 1200/1400mm sweep complete all as specified and directed

S & F in replacement for Sub Main wiring with two single core 6 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade drawn in through flexible non metallic PVC casing caping with and including PVC insulated 6 Sqmm multi strand copper conductor as continuous earth wire in green colour connected to common earth dolly ,complete all as specified and as directed (Note : PVC cable and PVC casing caping shall be ISI marked) Note :- Two length of 6 Sqmm cable and one length of 6 Sqmm earth cable along with PVC casing caping will be measured as one running length

S & F in replacement for Sub Main wiring with two single core 4 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade drawn in through flexible non metallic PVC casing caping with and including PVC insulated 4 Sqmm multi strand copper conductor as continuous earth wire in green colour connected to common earth dolly ,complete all as specified and as directed (Note : PVC cable and PVC casing caping shall be ISI marked) Note :- Two length of 4 Sqmm cable and one length of 4 Sqmm earth cable along with PVC casing caping will be measured as one running length

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof IP 42 suitable for incorporation MCBs and isolators etc including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 12 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof IP 42 suitable for incorporation MCBs and isolators etc including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed

S & F in replacement MCB ‘B’ series type suitable for 240 volts, AC supply 6 to 32 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed.

S & F in replacement MCB ‘B’ series type suitable for 240 volts,10 KA, AC supply 6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed.

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted TP & N 4 ways, 415 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof, IP42 suitable for incorporation MCBs and isolators etc including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed

S & F in replacement MCB ‘B’ series type suitable for 415 volts, 10 KA, AC supply 40 to 100 Amps, triple pole and neutral (TPN) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed

Supply & fixing in replacement of meter box of size (0.9mX0.9mX0.2m) made of Polycarbonate shall have Transparent cover,should be weather/ vermin proof, anti-acid, anti corrosive, UV resistance, fire retardant, thickeness 2.25 mm double door,single opening with lock arrangement suitable for fixing 04 Electric meter & TPN DB box including taking down existing electric meters , refixing them with two single core PVC copper conductor unsheathed wire multistranded 4 sqmm,properly painting complete and fixing in wall with suitable cutting,cement & brick work etc all as specified and directed

S&F exhaust fan made of sturdy engineering plastic of 250mm sweep ,240 volt, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc.

Supply and fixing in replacement anti suicide ceiling fan rod (12"/18"/24") white/brown, others including metallic as per need, MS pipe zinc plated pipe OD-19mm, thickness 1.8+/-0.05mm, Spring set grade 3 Carbon spring steel material, zinc plated, MSME tested, load of 22 kgs come on the anti sucide impact fan rod, the rod will get open from centre, spring inside will be expanded, fan clamp with rubber reel nut bolt & safety pin as suitable for ceiling fan complete all as specified and directed

venus enterprises (BID ID -3154609)