6 TH FINANCE COMISSION 2022 - 23 And 2023-24

Amount

Earth work open excavation and depositing on bank with in the initial lead of 10m and a lift of 2m in hard stiff clay, stiff block cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc., as per SS 20 A. TNDSS NO: 23 & 24 VI (S2) VI,VII 9,10 with standard specifications.

Earth work open excavation and depositing on bank with in the initial lead of 10m and a lift of 2m in hard stiff clay, stiff block cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc., as per SS 20 A. TNDSS NO: 23 & 24 VI (S2) VI,VII 9,10 with standard specifications.- Grade Beam.

Plain Cement Concrete 1:4:8 Mix (one Part of cement, four Part of M- Sand and Eight Part of aggrigate) using 40 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc., complete as per TNDSS NO : 28 & VI (S2) VI (S5A) VII standard specifications as directed by Engineer incharge.

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requirements of IS standards.

A)Upto basement

B)Ground Floor

Supplying and erecting centering to sides and soffits including supports and strutting with necessary cross bracing for plain surface such as RCC slabs rectangular beams all beams lintels etc., centering for soffits upto 3 meter height using mild steel sheet of size 90 cm x 60 cm x 10 mm gauge with MS angles of size 25mm x 25mm x 3mm laid over silver oak (CW) joists of size 10cm x 6cm spaced upto 90cm c/c and casurina props or 10 cm to 13 cm dia spaced at 0.750 cm c/c complying with standard specifications as per TNDSS NO : 30 & 86.

For Square, Rectancular column

For Grade beam

For Roof Beam & Slab

Supplying and fabrication of steel and placing in position of TMT steel rods for RCC works as per design given including cost of steel and GI binding wire in all floors etc., complete complying with standard specification in TNDSS NO:97 V,VI (S6) VII (S6), VII-3.

Brick Work in Cement Mortor 1:5 Mix (one cement, five M- Sand) using new best II Class Bricks of size 9 ” x 4 3/8 “x 2 3/4 ” from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.(For 10 M3)

Foundation &Basement

Above basement

Plastering in Cement Mortor 1:5 Mix (one cement, five M- Sand) 12mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.

Special ceiling Plastering in Cement Mortor 1:3 Mix (one Cement, Three M- Sand ) 10mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications-10 m2.

Plastering in Cement Mortar 1:3 Mix (one Cement, Three M- Sand ) 20mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete . complying with std. specifications

Supplying and fixing of M.S grill of approved design for doors, windows and ventilators using necessary mild steel flats for inner and outer memebers which should be fixed to window frames inclusive of priming coat of best approved quality red oxide primer etc., complete complying with standard specifications.

Painting Two Coats on new Iron works with best synthetic enamel paint of approved colour and quality – 10m2.

Finishing the top of roof with one course of machine pressed tiles 23 C.m x 23 C.m x 2 C.m size using cement mortor 1:3 mix mixed with 2% by weight of Crude Oil and pointing with Cement Mortor 1:3 mix Cost of all materials and labour charges and brick jelly concrete etc., complete as per standard specifications.

Exterior Emulsion paint Two coats with good quality of approved Emulsion paint including cost of all materials to site and all labour charges for mixing applying and proper curring etc., Complete as per Standard Specifications for 10 sqm

Supplying and fixing in Position of Indian Oriya pan type water closet with “P’’ or “S’’ trap to set in brick jelly concrete 1:4:8 Mix concrete 10 cm thick using 20mm brick jelly and top finished with c.m. 1:3 mix 20mm thick without any leakage etc. complete.

Supplying and fixing in position colour glazed EUROPEAN WATER CLOSET with 'P' or 'S' trap and double flapped seat cover, 10.00 litres capacity P.V.C. low level FLUSHING TANK including all internal fittings fixed on C.I. brackets, 12mm PVC or brass nipple, chromium plated brown headed stopcock, 12mm nylon connection with necessary teakwood plugs, clamps, screws to the portion coming with walls and floors, including dismantling masonry and redoing the same to the original condition.

Fabricating, supplying and fixing in positon of SOLID PVC DOORS with frames of different sizes as per the specifications given below: PVC door frames made out of best quality PVC extruded section of 40mm * 58 mm * 2.50 mm +/- 0.3 mm thick, having multichamber cross section and duly reinforced with steel to be mitre cut at the corners and welded including providing tie rod at the bottom and necessary weather seal etc., and PVC door shutters made out of extruded plastic section of 60 mm * 24 mm size in the configruation of an "A" section for shutter frames and multi-chamber hollow plastic section of 200 mm *200 mm*1 mm (average thickness) with tongue and groove section for panels etc., with necessary holdfasts, rubber beedings, furniture fittings, locking arrangements etc., complete including dimantling the masnery, making chippings, holes in the RCC column, beam etc., wherever necessary with power drill to the extent required and redoing the same to the original condition after fixing etc., complete as per specifications and as directed by the departmental officers.

Laying with new C.C. Laminated tiles (Like Dora tiles Eurocon tiles etc),(anti skid) of 20mm thick of approved spl quality and set in Cement Mortar 1:3 (1 of cement and 3 of M- Sand ) 20mm. Thick using river M- Sand and pointing with colour cement using at the rate of 0.40 kg/M2 and mixing with colour pigment at the rate of 0.3 Kg/M2 including finishing complete with Standard Specification and as directed by the DePart ofmental Officers etc.,

Supplying and fixing over the floors best quality of scratch ceramic tiles of 30 c.m x 30c.m x 6mm size of approved colour laying with cement mortor 1:3 mix pointing the joints with colour pigments etc. Complete.

Paving the floor with descrgned coloured vitrified tiles of size 600 x 600 x 8mm of best quality and approved variety complying / confirming ISI specification land over cement mortar 1:3 (one cement and three M- Sand) 20mm thick and pomted with same coloured cement neatly etc., complete.

Collection supply and filling of well gravel filling approved quarry including cost and Conveyance of all materials to site and all labour charges for filling etc., Complete.

Supplying and fixing of Cuddapah Slab 20/30 mm Thick Including Cost and Conveyance.

Dadooing the walls with glazed tiles of 30 c.m x 20 c.m 6mm size laid in cement mortor 1:2 mix 10mm thick and pointing with 0.40 kg white cement per m2 etc.

Wiring with 2x1.50 sq.mm(22/0.3) PVC unsheathed SC Copper conductor of 1100V grade insulated PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with Hylum sheet of 3mm thick cover with T.W switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good ot concealed portion with suitable colour for PVC concealed Light point / fanpoint (For electronic regulator). (PWD standard data No.22).

Wiring with 2x4 sqmm (56/0.3) PVC insulated Cu. Conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mmx100mmx113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non Inter locking CS plug with continuous earth wire connection of 14 SWG TC wire. And making good of the concealed portion. With suitable colour for concealed power plug point. (PWD standard data No.SD 38.)

Drilling of 150mm dia borewells in allivual soil or sedimetary strata using rig by first drilling a pilot bore of 150mm dia direct rotary and circulation method using rig tools, fuel, labour drilling, benotonite mud and water required for drilling at th

Reaming from 150mm dia pilot bore to 300mm dia bore as directed by departmental officer upto 60m below ground level

Supply and delivery of 150mm blue plain PVC casing pipe (165mm dia OD -CS) as per standard specification(Cost including Excise duty

Labour charges for inserting PVC casing with or without slots into drilled hole including welding the joints etc complete and supplying and packing the annular spaces with pebbles of size and quality as approved by departmental officers for 150mm dia cas

Charges for developing the borewell with air compressor of 600 cfm capacity (Minimum 8 hours) including transportation and fuel charges for compressor as directed by the departmental officers and conducting yield test by 'V' notch method etc complete

Drilling of 150 mm bore well in Hard rock formation using rig including transportation and fuel charges of Rig to site and all labour charges etc complete

Supply and delivery of 2000 litres capacity HDPE tank of ISI mark including transportation charges to site and all labour charges etc complete(Asper TWAD Board Rate-2022-2023)

Supply and delivery of following materials as per ISI specification including cost and conveyance to site and all labour charges etc complete

1.5H.P submersible motor 15 lpmX90m head Single Phase (IS 8034.(Asper TWAD Board Rate-2022-2023)

Panel board for 1.5HP submersible motor)

2.5 sq.mm PVC insulted copper flat cable(IS-690/1990)

MS Bore clamp set using MS flat 10 x 3 mm for 5" bore pipe

M.s Bore cover

40mm UPVC Pipe

Nylon Rope

Errection for labours charges up to 5 HP submersible motor and pump set etc., completed

Supplying and Fixing of Good quality EB box (Size 0.75mX0.45mX0.75m using 50x50x4mm M.S.angle and 16Gauge M.S.Sheet and 25X3mm M.S.Plate)including cost and conveyance to site and all labour charges etc complete

Supply and run of 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade on 7/20 GI bearer wire for service connection mains.(PWD standard data No.SD. 64).

Supply and run of 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 25mm dia GI pipe (Class ‘B’) suitably bent at both ends with necessary angle iron upright and end supports for mains(PWD standard data No.SD. 69).

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings.The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.

Supply and fixing of 16A DP Switch with metal clad of 500V with F&N (Side Handle) on suitable TW Board with earth connection only. (PWD standard data No.SD. 141).

M/s. KK CONSTRUCTION (BID ID -1105600)