138WE/L-70/2019-20

Amount

Surface excavation (not exceeding) 30 cm deep and averaging 15cm deep and getting out as in hard and dense soil, complete all as specified and as directed.

Dewatering the contiminated / waste water from soakage well of 1.80m dia & 3m deep through pumping / manually and dispose off therein open drain or low lying area including cutting holes through slab/ wall as required for inserting pipe and making good the same to match with existing surface complete all as specified and as directed by the Engineer -in-Charge.

Moorum / red bajri filling in pits, floors or pavings, laid in layers n.exc 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches, not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in hard/dense soil, complete all as specified and as directed by the Engineer- in- Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and as directed by the Engineer- in- Charge.

Removing excavated materials/ soils, not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.50 mtrs above the starting point, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate), as in filling and mass concrete in foundation, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for reinforced cement concrete M-30 (Design Mix) using 20 mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams, plint beams, bases for columns etc basement slabs , under reamed piles and mass concrete, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for reinforced cement concrete M-30 (Design Mix) using 20 mm graded crushed stone aggregates as in columns, pillars, piers, posts, and struts, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for reinforced cement concrete M-30 (Design Mix) using 20 mm graded crushed stone aggregates as in beams, cantilevers, bressummers, lintels over 1.5 m span, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for reinforced cement concrete M-30 (Design Mix) using 20 mm graded crushed stone aggregates as in chajjas, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for reinforced cement concrete M-30 (Design Mix) as in slabs supported on walls, beams and columns in floors, roof, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for form work to sides of rough finished surface of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or batter, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overlaps etc, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for form work to sides of rough finished surface of concrete square, rectangular or polygonal in pillars, posts, struts, piers, columns and stanchions, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for form work to soffits of rough finished surface of concrete suspended slabs such as roof slabs, floor slabs, landings and similar work n.exc 200 mm thick horizontal or sloping, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for form work to edges of concrete flats, treads , breaks in floors, window sills, concrete railings, openings in concrete walls, floor and roof n. exc 20 cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide, complete all as specified and as directed by the Engineer- in- Charge.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by the Engineer- in- Charge.

Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for precast cement concrete block masonary type C-1, 1:3:6 ( using 20 mm graded crushed stone aggregates) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for precast cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregates) set in cement mortar 1:4 (with plain or inter locking joints as directed) setting in mortar complete in walls, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for sand filling under floors or in foundation including watering and consolidation, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for hard core of gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface with broken stones, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for plain cement concrete 75 mm thick, 1:4:8 type D2 (using 40mm graded crushed stone aggregates) as in sub base, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for plain cement concrete 25 mm thick, 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in floor, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for plain cement concrete 40 mm thick, 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in damp proofing course, complete all as specified and as directed by the Engineer- in- Charge.

Brushing neat cement slurry with 3.0 kg of cement per square metre, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for 15mm thick screed bed or bedding layer of mortar in CM 1:4 for laying floor finishes, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixtue of pigment to match the shade of granite stone including grinding and polishing, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for 20mm thick granite of any type tiles machine cut, in skirting/dados laid over 10mm thick rendering in cement mortar )1:3) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for Non skid coloured ceramic tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for Glazed ceramic tiles coloured 300 x 200 mm x 7mm thick for works on vertical surfaces such as skirting/dados , set and jointed in neat cement slurry and pointed in coloured cement to match including rendering 10 mm thick on fair faces or other than fair faces of brick work in cement mortar 1:3, finished even and fair as in backing layer, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed by the Engineer- in- Charge

Material and Labour for 15 mm thick cement plaster in cement mortar 1:6 on brick or concrete surface etc. on wall finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer- in- Charge

Material and Labour for 5 mm thick cement plaster in cement mortar 1:3 on brick or concrete surface etc. on ceiling finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer- in- Charge

Material and Labour for rendering 15 mm thick on fair faces of brick work or cement concrete surfaces in cement mortar 1:4, finished fair and even without using extra cement incl mixing of water proofing admixture complete all as specified and as directed by the Engineer- in- Charge. (Note: Water Proofing compound shall be measured and paid for separately)

Supply only liquid water proofing admixture, complete all as specified and as directed by the Engineer- in- Charge. (Makes :Pidilite Industries / Impermo /Snowcem India Ltd / Sika )

Matrial and Labour for plain cement concrete 75 mm thick 1:3:6, type C-1 ( using 20 mm graded crushed stone aggregate ) as in plinth protection, paving finished even and smooth without using extra cement complete all as specified and as directed by the Engineer- in- Charge.

Matrial and Labour for plain cement concrete 1:3:6, type C-1 ( Using 20mm graded aggregate) as in surface channels and drains, complete all as specified and as directed by the Engineer- in- Charge.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, dimnishing pieces, caps and plugs, unions etc) of nominal bore dia 15 mm, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, dimnishing pieces, caps and plugs, unions etc) of nominal bore dia 20 mm, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing Tubular Towel rail 600mm long of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing Stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20mm bore, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing Fancy type, Pillar taps, cast copper alloy, with capstan heads , chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing Bib taps,short body, fancy type, cast copper alloy, brass chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing PVC connections 15 mm size with PTMT nuts of length 450 mm, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing gun metal globe or gate valve with iron wheel 20 mm dia, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for Vitreous china wash hand basin with pedestal, coloured, flat back of size 550 x 400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450mm length with PTMT nuts, fixed in repairs, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for Low density polyethylene pipes, 32 mm dia (LDPE) of pressure rating 6 kgf/cm2 complete, fixed to sink/wash hand basin complete all as specified and as directed by the Engineer- in- Charge.

Soap dish, vitreous china white approximate size 160x160x90 mm fixed to plugs chromium plated brass screws, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing rotational moulded polyethylene water storage tank heavy duty PUF insulated 5 layers storage tank ideally suitable for extreme temperature +35 degree centigrade to -45 degree centigrade conditions and the outer FRP (Fibre glass reinforced plastic) layers withstand vagaries of nature and prevent erosion/damages of the tank of capacity 500 ltrs complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for 12 mm thick prelaminated particle board interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw as in palmet boxes, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for 12mm thick Veneered decorative plywood grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with nails to timber frame work in wall, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing anodised aluminium snap grid frame work for false ceiling ( grid size 605 X 605 mm) fixed to walls with rawl plugs and screws and hang to roof members with 6 mm dia GI wire (upto 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size 60 mm long, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing second class hardwood plain fillets, square, rectangular or triangular in section clean sawn secured with nails sectional area exc 13 and not exc 25 Sqcm complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for 2nd class hardwood n. exc 6 sqm moulding as in cornices, picture rail, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for 2nd class hardwood timber plain fillets square,rectangular or tringular in section clean swan scured with nails n.exc 3 Sqcm complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing aluminium extruded section Door closer hydraulically regulated, designation no 2 universal type, suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 kg and fixed, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing 140mm long Floor door stopper of aluminium alloy body and tounge, anodised, with hard drawn steel spring fixed in floor, complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing 25mm dia aluminium anodised alloy curtain rod including wooden ornamental/decorative bracket and end cap, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for powder coating minimum thickness 50 micron Anodised aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for powder coating minimum thickness 50 micron Anodised aluminium door shutters sliding type, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for powder coating minimum thickness 50 micron Anodised aluminium window and ventilator shutters sliding type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and as directed by the Engineer- in- Charge.

Supply and fixing sheet glass 5.5 mm thick, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for SDC Laminated flooring 8mm thick of any colour manufactured by direct pressure laminated (DPL) wherein the empty Abrasive aluminium oxide overlay along with metamine impregnated decorated film is directly fused with the back with flooring locking profile in design with double click looking system on the length and single locking width along with desire locking strength, complete all as specified and as directed by the Engineer- in- Charge.

Material and Labour for Preparing plastered new surfaces of walls and applying two coats of cement base paint, complete all as specified and as directed by the Engineer- in- Charge.

Material and labour for point wiring with 1.5 Sqmm copper conductor (Multi-standard) PVC insulated and unsheathed electric cable 1100 volts in and including PVC casing and capping of 25 mm and above (as per conductor run )with all fittings/ accessories and including PVC insulated and unsheathed electric cable 1100 volts1.5 Sqmm ( multi-stranded) copper conductor single core( Green co lour) cable as continuous earth wire connected to common earth dolly including 50 mm deep box made of 2nd class hard board of required size and shape etc all covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point independent controlled by one, one way switch complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 72 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 72 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 72 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

All as per serial item No. 72 here-in-before, but for one socket outlet 15 Amps on independent board with 4 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing switch piano flush button single pole one way 5 Amps complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing switch, socket combination 2 in 1, 5 Amp, flush type complete all as specified and as directed by Engr-in-charge.

Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5A/16A, 5 in 1 flush type complete all as specified and as directed by Engr-in-charge.

Supply and fixing angular lamp holder, PVC/Polycaronate type with back plate suitable for 10/15/18 watt LED bulb for batten fittings complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing LED bulb 10 Watt , complete all as specified and as directed by Engineer-in-Charge. Make: Havells.

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply & fixing batten for LED tube light 1x20 Watt Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver including making suitable connection of tube light fitting to ceilling rose by 23/0.0076 copper flexible wire complete all as specified and as directed by Engineer-in-Charge. ENDURA LINEAR Neo Model No - 20W LED 3000K (1144 mm) LHEWEBP5IN1W020 Diffused Make- Havells or equivalent in Philips .

Supply & fixing LED tube light 1x20 Watt LED suited for installation for LED Batten LHEWEBP5IN1W020 Diffused alll as specified and as directed by Engr-in-charge ENDURA LINEAR Neo Model No - 20W LED LHLDCLXNUK8Z020 Diffused Make- Havells or equivalent in Philips as directed by Engineer-in-Charge.

Supply and fixing Recess mounting LED 2X2 luminaries,ultra modern design architectural 2x2 LED luminiries soft light and glare free symmetrical illuminate 34 watt LED 4000K and making appropriate connection to false ceilling of the appropriate size including suitable connection light fitting to ceilling rose by 1.5 sq mm 2 runs copper flexible wire, complete all as specified and as directed by Engr-in- Charge. Model No-LHEWDRP6PLIW034 Make- Havells/ Philips/ or Eqiv approved make.

S&F decorative ceiling/wall mounted "Bulkhead" luminaire 10 watt LED IP 65 protection with engineering plastic housing and top frame with opal diffuser as per cat part No. "LHEOAOP7UZ6W010" suitable for and incl 1X10W LED of make Havells or equivqlent in bajaj/philips complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 4 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing MCB single pole and neutral 32 to 63 Amps , 240 volt, 10 KA, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing MCB single pole 6 to 16 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 16 Sqmm, 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and as directed by the Engr-in-Charge

Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified and as directed by Engineer-in-Charge.

Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cm thick, complete all as specified and directed Note: Punned thickness shall be measured.

Supply and fixing Exhaust fan plastic body 250 mm Sweep , 230 volt 50 Hz, with louvers and shutters complete all as specified and as directed by Engr- in- charge. Make- Bajaj or Equiv as per approved make.

Earthing complete with galvanized steel earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected with galvanized iron wire 4.0mm dia as earth lead means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 15 mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1(using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test point etc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and as directed. Note: The cost of excavation and earth work, PCC pit and pit covers, funnel and watering pipe, wire mesh, charcoal dust and common salt, 15mm dia, medium grade, GI pipe as protection to earth lead and earth lead as 4.0mm dia GI wire (main earthing lead from earth electrode to test point length not less than 7.5mtrs) shall be deemed included in the unit rate for earthing.

HORIZON CONSTRUCTION COMPANY

M/S TRADE LINK

M/S GLOBAL ENGINEERS