SPL REPAIRS TO BLDG NOS P376 P377 AND P378 OF GE(P) GANGTOK ADDITION ALTERATION TO BLDG NO T35 PROVN OF STORAGE SHED NEAR BLDG NO T39 PROVN OF TANK STAGING FOR BLDG NO PB31 01 TO PB31 08 OR MD ACCN PB27 01 TO PB27 04 AND PB28 01 TO PB28 04 AND PROVN

Amount

Dismantling old PGI/CGI/AC sheeting any gauge, thickness, including Nainital. Sikkim or similar pattern roof/facia etc complete.

Demolition of birck work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc including ashlar facings dressed stone work and precast concrete articles and precast concrete block walling for portions of wall ordered to be dismantled

Demolition of reinforced cement concrete work (reinforcement cut as required to facilitate demolition) as in floors (other than groundfloors) columns, beams, staircases, landing, chajjas and similar suspended work

Separating, scraping and cleaning of reinforcement (Demolition of concrete measured separately)

Dismantling structral steel work including doors, gates but excluding framed truss etc.

Dismantling of unframed timber in fillets, rails, posts, rafters, purlins etc under 40 Sqcm and over in section complete all as specified and directed

Taking down cement plaster of any description on brick or stone walls incl raking out joints hacking for key, scrubing down with water etc complete all specified and directed.

Demolition of concrete in ground floor and pavings n.exc 15cm thick (below or above ground level) complete all as specified and directed.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified and directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing of dismantled materials/rubbish from site complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) each area n exc 1.5 Sqm all as specified and directed.

Taking down chowkats or frames with shutters exc 1.5 Sqm and n.exc 4 Sqm (without taking off shutter from the frames) each area n exc 1.5 Sqm and refixing the same/other opening complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub-base finished the surface fair and even without using extra cement etc complete all as specified and as directed.

S&F roof trusses (framed), trussed, purlins, post, crane grantries, rails and fastenings and heavy bracket framing (Beam, tee angle, channel or flat and hollow sections) including distance pieces, cleats etc conforming to Fe-290 (Gde E-165_

Ditto all as item No 14 above but fixing only

Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and directed by the Engr-in-Charge.

Supply and fix in repair 15mm bore dia angular stop cock, cast copper, fancy type chromium plated, with wall flange screwed down, screwed from iron pipe or union and complete all as directed

Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheets of any colour having tensile strength of 550 Mpa as in ridges, valley, eaves, etc fixed with self tapping screws complete all as specified and directed by the Engr-in-Charge

M&L for lacquer coated precast chequred cement concrete tiles made with grey cement and pigment of size 300 x 300 x 25 mm thick as in pavement / footpath, set and jointed in neat cement slurry and pointed with cement laid over laid over and including screed bed/bedding layer of 15mm thick in cemnt mortar (1:4) compelte all as directed.

Material and Labour for precast cement concrete solid block masonry Type C1 (1:3:6) using 20 mm graded aggregate as per IS 383 exc 10 cm in width and setting in cement mortar (1:6) complete all as specified and as directed by the Engr-in-Charge.

M&L for rendering 20mm thick in cement mortar (1:4) in two layer of 10mm thick each with using WPC shall be mixed with cement mortar in finishing outer layer only as per manufacturer's instruction, on other than fair face of brick/stone masonry (external surfaces) finished surface fair and even without using extra cement complete all as specified and as directed. Note : (WPC shall be measured and paid separately as supply only)

M&L for rendering 15mm thick in cement mortar (1:6) on fair face of brick or concrete surfaces finished surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar (1:4) on fair face of brick or concrete surfaces finished surface even and smooth without using extra cement complete all as specified and as directed.

M&L for applying three coats of white wash on new plastered wall surface including preparation of new and previously untreated surfaces on wall complete all as specified and directed

M&L for applying two coats of white wash on old plastered wall surface including preparation of old surfaces on wall complete all as specified and directed

M&L for preparation of new plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over new wall surface on a coat 1mm wall care putty complete all as specified and directed. (Putty shall be paid and measured separately)

M&L for preparation of complete removal of existing treatment on old plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over old surface on a coat of 1mm thick wall care putty complete all as specified and directed (Putty shall be paid and measured separately)

M&L for providing and applying plaster of paris putty of 1mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed

S&F 9/10mm thick PVC ceiling/wall panels of interlocking types, width 250/255 mm with lamination design and exc 60% of PVC content including necessary H-joints, internal/external corner cove, F/J edge trims where required fixed with hidden screws to steel/wooden frame work complete all as specified and as directed

S&F powder coated GI grid frame work for false ceiling comprising of the following sections for making partition of 600x600mm size fixed to walls with rawl plugs and screws and hanged to roof with and including 1.18 mm dia GI wire suspender of suitable length and buterfly clips, size of main tee shall be 23mmx 28mmx 0.30mm thick, cross tee shall be 24x 23x .30 mm thick and wall angle shall be 20mmx20mmx0.30mm thick complete all as specified and directed.

S&F for 4mm thick Non asbestos fibre cement building board (E-board) of approved texture for insulation and acoustic purpose of size 595x595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surface and applying one coats of oil emulsion distemper over a coat of primer including preparation of surfaces complete all as specified and directed.

Hacking out of old broken glass any thickness size quality or description from metal frame including punching or drilling out old glazing pins.

M&L for second class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded on chamfered put together with glue pinned and joints complete all as specified and directed.

S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying & fixing in opening as per specification and drawing complete all as specified and directed.

Supply and fix factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F of flush shutters 35 mm thick, solid core construction, with particle board core commercial type on one side and one face covered with decorative face veneer wtih lipping/frame to match omplete all as specified and directed.

S&F second class hardwood, glazed and skelton shutters 25 mm thick open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I Section8, Clause 8.20 (a) supplied and fitted to chowkats omplete all as specified and directed.

S&F MS but hinges 100mm long complete

All as per item No 38 above but 75mm long complete

S&F 200mm long aluminium, anodised, barrel tower bolts of extruded section complete

All as per item No 40 above but 150mm long complete

S&F 150mm long aluminium handles, cast type, anodised complete

All as per item No 42 above but 100mm long complete

M&L for 250 mm long mild steel sliding door bolts, plate type, stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed..

M&L for preparation of new or previously untreated wooden surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

S&F and in repair Mild steel framed work such as grills, gratings etc, with ends of bars, shoulded and/or riveted or forged in spikes, framed guard bars, walk ways, railings, frame work of water tanks and similar works conforming to Fe 290, Gde-E-165 all as specified and directed incl taking down old scrap iron grill.

M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of old or previously treated steel surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint over old steel surface complete all as specified and directed

S&F 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane

M&L for preparation of old or previously treated wooden surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint over wooden surface complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and not exc 1.5 m in depth for and getting out in soft / loose soil for foundation etc complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in foundation and mass concrete complete all as directed.

Returning filling in soil/back filling of retaining walls using approved earth obtained from excavtion including watering, well ramming in layers etc complete all as specified and as directed.

Removing excavated materials (soil) not exc 50 m complete all as specified and as directed.

M&L non skid ceramic colured tiles 7 to 8mm thick, area of each tile exceeding 0.11 sqm but n.exc 0.36 sqm, in floors etc. set & jointed in neat cement slurry & pointd in coloured cement to match incl 15mm thick screed bed with CM 1:6 complete all as specified and as directed.

Ditto all as item No 55 above but on vertical surface of wall like skerting/dado etc over and incl 15mm thick rendering complete

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed.

M&L glazed ceramic coloured tiles 350x250x7mm/450x350x7mm thick on vertical surfaces such as skirting, dados, set & Jointed in neat cement slurry & pointed in colour cement to match incl 10mm thick screed bed with CM 1:4 complete all as specified and as directed.

S&F virified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer in CM (1:6) all as specified and as directed

Ditto all as item No 59 above but on vertical surface of wall like skerting/dadoi etc on 15mm thick rendering complete

M&L for applying two coat of exterior acrylic emulsion weather proof paint over a coat of primer over a coat of primer on new/old plastered surface including preparation of old/new plastered surfaces of wall complete all as specified and directed

S&F 18-20mm thick granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite granite stone including cutting and polishing etc including 20mm thick screed bed in CM 1:6 including dismantling old existing stone/slab complete all as specified and directed

Supply and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators etc weight n.less than 0.55 Kg/RM with one or more rebates including joining cleat for fixing etc. Complete all as specified

Supply and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sceitons of approved make conforming to IS:733 and IS:1285 fixing with dash fasterners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with requried EPD rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free straght, mitred and jointed mechanically wherever requried including cleat angle, aluminium snap beading for glazing/ panelling CP brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F 5.5mm thick glass pane area exc 0.5Sqm but n exc 1 Sqm fixed on aluminium frame work of appropriate section as directed by Engr-in-Charge.

S&F prelaminated particle board of 12mm thick interior grade, prelaminated both side with decorative choise laminations fixed with aluminum frame work of any sections as directed by Engr-in-Charge

Supply anf fix in repair, one piece vitreous china EWC of size 635mm x 350mm x 740mm with soft close seat cover and twin flush fittings incl 'S' or 'P' trap Make CERA-CREATTLE, Cat No S1013190 incl necessary connections complete all as specified and as directed

S&F in repair counter sunk wash hand basin of size 560mm x 470mm x 190mm incl all accessories Make- CERA

S&F chromium plated single lever basin mixer with 305 mm (12") extended body and 600mm braided connection pipe (without pop-up) Make - CERA Cat No : F1016452

S&F in repair one/two way bib tap, long body cast copper alloy, chromium plated with cructh or butterfly handle with healthfuceset, screwed down for 15mm bore GI pipe or for brass ferrule. Make : ESSCO Cat part No.SQT-512KN or equivalent.

Supply and fix in repair 75mm dia PVC floor trap of outlet, with gratings, including jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) complete all as specified and as directed.

M&L for non skid ceramic outdoor coloured tiles 8-10mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified and directed

M & L RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in foundation, including raft footings, foundation beams, plinth beams, bases for columns, lintel beam, cover slab etc basement slabs, under reamed piles and mass concrete incl necessary form work complete all as specified and as directed. (Note : Re-inforcement shall be measured and paid separately)

M & L RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in Columns,pillars, piers, posts and struts complete all as specified and as directed.

M & L RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed. (Note : Re-inforcement shall be measured and paid separately)

M & L RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. (Note : Re-inforcement shall be measured and paid separately)

M&L mild steel bars 10mm dia & over cut to length bent to shape required, including carcking, bending spirally to proper for columns, hooking end & binding with and inch mild steel wire not less than 0.9mm dia securing with clips quality conforming to TMT bars complete all as specified and directed.

M&L mild steel bars 6 to 8 mm dia cut to length bent to shape required, including carcking, bending spirally to proper for columns, hooking end & binding with and inch mild steel wire not less than 0.9mm dia securing with clips quality conforming to TMT bars complete all as specified and directed

Material & labour for Mild steel TMT bars 5mm to 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required, including cranking , bending spirally for hooping for columns , hooking ends and binding with and including mild steel wirenot less than 0.9 mm dia (annealed) or securing with clips complete all as specified & as directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for flat rough finished surface of concrete

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions etc for square or rectangular rough finished surface of concrete

Use and waste of formwork (flat) to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, Lintel, cantilevers, shelves including supports, overhangs etc also splays between floor and beam etc complete for flat rough finished surface of concrete

Use and waste of formwork to formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or slopping) etc complete for flat rough finished surface concrete

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but not exc 10cm wide for rough surface

M&L Sand filling in layers under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63mm deposited spread and levelled in layers n exc 15 cm thick watered and rammed to true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection/path/hardstanding finished the concrete surfaces even and smooth without using extra cement etc complete all as specified and as directed.

S&F decorative type curtain rod, chromium plated 25mm dia with fixing btackets stops and complete fittings including making good the surface were damaged all as directed by Engr-in-Charge

S&F for PVC (SWR) pipes 110mm dia, single socketed, in any length with rubber ring joints fixed to wall, Floor as drainage complete all as specified and directed.

Supply only liquid water proofing compound.

M&L for Excavating in post holes (or similar holes) each n exc 0.5 cu.m, getting out soft/loose soil, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm complete all as specified and directed.

M&L for framed work as in door or gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing complete.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 all as directed by the Engr-in-charge.

M&L for PCC 1:2:4 type B1 (20mm graded aggregate) as in coping, bed plates, parapet, plinth course including weathering, slightly rounded or chamfered angles and throating all as specified and as directed

Supply and fix 20mm Bore steel water tubing medium grade,galvanised fitting fixed complete to walls and ceiling or floor complete all as specified and directed.

Supply and fix galvanished steel water tubing 25mm bore, medium grade with all fittings and fixed complete to walls/ceilings or laid in floors complete all as directed by the Engr-in-Charge.

S&F Gun-metal, globe or gate valves 25mm bore ISI marked with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F Gun-metal, globe or gate valves 20mm bore with iron wheel head screwed both ends for GI pipe complete all as specified and directed.

Diconnecting existing tanks, of capacity exc 500 Ltr but n. Exc 1000 Ltr setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position. (cleaning repairing etc measured separately)

M&L for 100mm thick PCC 1:2:4 type B2 (using 40mm graded stone aggregate) as in hardstanding/flooring/path etc finished the concrete surfaces even and fair without using extra cement etc. complete all as specified and as directed.

M&L for 25mm thick PCC type B-2 1:2:4 type B-1 (using 20mm graded stone agg) finished concrete surfaces even and smooth complete all as specified and directed

Dismantling of unframed timber scantling 40 Sqcm and over in section complete all as specified and directed

Surface excavation n exc 30 cm deep and averaging 15cm deep and getting out in soft /loose soil complete all as specifed.

M&L for PCC 1:3:6 type C2 (using 40 mm grade stone aggregate), as in surface channels/drain including necessary formwork complete all as specified and directed.

Demolition of bamboo framing any type in roof or wall including attached whole bamboo or bamboo trellis work

M&L for mild steel framed work such as grills, gratings etc.. With ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders framed balusters, walk ways railings framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and as directed incl taking down old scrap iron grill.

Taking down 15mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as directed

Taking down 20mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as directed

Supply and fix galvanished steel water tubing 15 mm bore, medium grade with all fittings and fixed complete to walls/ceilings or laid in floors complete all as directed by the Engr-in-Charge.

Supply and fix galvanished steel water tubing 20 mm bore, medium grade with all fittings and fixed complete to walls/ceilings or laid in floors complete all as directed by the Engr-in-Charge.

Refixing of old 15mm bore steel tubing and connections in new or old position (wall, ceiling or floor etc) complete all as directed

Refixing of old 20mm bore steel tubing and connections in new or old position (wall, ceiling or floor etc) complete all as directed

S&F in repairs of vitreous china wash down water closet pedestal pattern white with all fittings fixed as in repairs (excluding flushing cistern and flush pipe) including plastic water closet seat,white closed pattern with flat bottom and cover and MS CP aluminium/ PVC hinging device of Make: ESSCO Cat Pat No ECS-WHT-551PS

S&F in repairs for wash hand basin, vitreous china, white, flat back (550x400mm) cutting for and pinning ends of brackets,Indus Basin (white) or equivalent including 32 mm dia waste pipe with or without padestal all as specified and directed by Engr-in-charge of Make:ESSCO Cat Part No ECS-WHT-803 or equivalent.

M&L for Cutting chases, pinning in, making good to facing where required and pointing in CM 1:3 for concealed water tubing conduit wiring etc and making good, cutting n.exc 10cm girth as in stone or concrete block walls complete all as specified and directed.

S&F in repairs 10 litre capacity low level PVC flushing cistern (white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32mm dia PVC flush pipe and making all necessary connections complete as specified. Make: ESSCO Cat Part No WHE-WHT-183L or equivalent complete all as directed

Supply & fixing in repair of pillars taps,fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, scewed for iron pipe 15 mm bore of Make : ESSCO Cat part No SQT- 508KN or equivalent.

S&F of factory made steel windows with side hung shutters openable type including friction/box type hinges, steel handle and peg stay complete with glazing bars including a shoap coat of primer including complete all as directed

Taking down carefully the old unserviceable Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete including fixtures and fittings such as switches, ceiling rose pendants, regulators, sockets, light fittings etc and removing materials for taking credit and making good disturbed surfaces of wall floor etc all as specified and as directed

M & L for point wiring with 1.5 Sqmm PVC isulated unsheathed single core stranded copper conductor (FRLS) cable of working voltage 1100 Volts grade conforming to IS-694 pt-I & II of 2000 drawn in and including 25 mm size PVC casing caping (Double lock) with all casing capping fittings & accessories with 1.60 mm thick pressed steel or mild steel sheet sunk box covered with 3mm thick backelite sheet fixed with brass screws & cup washers including 1.5 sqmm PVC insulated unsheathed single core stranded copper conductor (FRLS) cable as earth continuity conductor connected to main switch/ DB's or common earth dolly complete for light point/ fan point/ exhaust fan point / call bell point controlled by one switch 5/6 AMP one way complete all as specifed and directed.

One light/ Fan point controlled by one, one way switch 5/6 Amps

One switch socket outlet point 5/6 Amps on independent board

One call bell/buzzer point controlled by one bell push

All as per item No 121 here-in-before but for one 3 pin 15 Amps power point on independent board with 4 Sqmm size FRLS PVC insulated unsheathed multistranded copper conductor cable with 2.5 Sqmm FRLS PVC insulated unsheathed solid copper conductor as earth wire complete all as specified and directed.

S &F switch piano flush button, single pole, one way, 5 amps (ISI marked) complete all as specified and directed.

Supply and fix ceiling rose, three terminals 230 volt (ISI marked) surface bakelite suitable for batten fitting complete all as specified and as directed. (Make : Havells Cat No AHLHXCW000 or equivalent in list of make)

S&F switch socket combination, 5-in-1, 5/6 Amps complete

S&F switch socket combination, 5-in-1, 15/16 Amps complete

S&F in repairs stepped type electronic fan regulator flush type on the existing phenolic laminated sheet/PVC etc as red 240 volts, ISI marked complete all as specified and directed. Make : Anchor Product Code No 38660 or equivalent of approved make

Supply & fix lamp holder angular/straight insulated body, with back plate suitable for battern futtings, white/ivory finish complete all as directed.

S&F 250mm sweep exhaust fan modular type, ventilus 10" model 240 volts, AC 50 Hz with all accessories such louvers, three core single core PVC insulated copper conductor of size 0.5 Sqmm from ceiling rose to fan, including cutting brick/block walls for fixing of fan and finishing the cutting surfaces even and smooth as per existing complete all as specified and as directed

Supply & fixing LED light fitting 1 x 18 W, 220 V AC decorative box type with dirver, holder including LED tube light connecting up with three core flexiable copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

M&L for concealed sub-main wiring along with earth wire of size of 2 x 6.0 Sqmm + 1 x 6.0 Sqmm earth wire, ISI marked FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and incl PVC rigid conduit (medium grade) with all fittings and accessories ISI marked including cutting chases for conduits and sinkings for sunken boxes and making good to walls, floors etc complete including taking down old unserviceable one all as specified and as directed.

S&F in repairs sheet metal enclosure for 4 way distribution Boards (DB's) single pole and neutral double door with IP-43 protection suitable for fixing MCB's/Isolators complete all as specified and as directed

Supply and fix in repairs MCB, single pole and neutral 63 amps, 240 volts, 'C', 10KA complete all as specified and as directed.

S&F MCB single pole 6 to 32 Amps 240 volts, 10KA rapturing capacity, C curve complete all as directed by Engineer-in-Charge

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.3mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level with top edge of the plate not less than 1.5 mtr below ground level connected to galvanised iron or steel earth lead wire 4mm dia size by means of nut/bolt and washer of galvanised iron or steel as shown in electrical plate No. 3 of SSR Part-I 2009 incl necessary excavation and earth work, GI pipe 20mm dia medium grade ISI marked for watering and GI pipe 15 mm dia medioum grade ISI marked pipe for protection of GI earth wire etc, PCC chamber with PCC (1:3:6) type c-2 precast RCC cover with reinforced cement concrete (1:2:4) type B1 (20 mm graded stone aggregate) reinforced with 8mm dia TMT bar @ 150mm c/c both way with provision of 10mm dia MS bar handle funnel, wire mesh, charcoal dust, salt etc connected to DB as indicated including testing complete

Supply anf fix modular switch 1 way 6 A, 1 module 230 volts, 50 Hz, ISI marked all as specified and directed

Supply anf fix Socket, 6A-2/3 pin combined 2 module 230 volts, 50 Hz, ISI marked all as specified and directed

Supply anf fix modular switch 1 way 16A, 1 module 230 volts, 50 Hz, ISI marked all as specified and directed

Supply anf fix socket, 6A/16A-2/3 pin combined 2 module 230 volts, 50 Hz, ISI marked all as specified and directed

Supply anf fix modular bell push 6A 1 module 230 volts, 50 Hz, ISI marked all as specified and directed

Supply and fix bell, AC, 230 volts single pole all as specified and as directed.

Supply and fixing round shape LED light fittings 1 x 12 W, 220 V, AC recessed type with high efficiency PMMA diffuser soft glare free light complet with drivers suitable for roof ceiling connecting up with three core flexiable copper conductor cable of suitable size complete all as directed.

Supply and fix decorative wall light made up of high grade engineering plastic material suitable for 9 watt LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed (Make : Havells Cat No PLUTOSURFACE4X1PLS34WLED857S or equivalent of approved make)

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300m

S&F MCB DB SPN 8 ways double door, IP-42, IK-09 with metal door, rated bus bars, earth bar neutral links complete incl blanking plates as required & fixed flush to wall /other surface compete all as specified and as directed

S&F MCB single pole neutral 5 to 32 Amps, 240 volts, 10 KA rupturing capacity, C curve complete all as directed by Engineer-in-Charge.

S&F bell push, flush type 5 Amps complete

Taking down existing Geyser 25 Ltrs capacity and keeping in safe custody and refixing in new or old position complete after repair works including replacing hot & cold PVC connection pipes (01 No each) etc all as specified and as directed

M/S ANIL KUMAR THAKUR

M/S S. S CHETTRI AND SONS

KAMLESH ENTERPRISE

BIJAY MITTAL

KARMA SHERPA