SPECIAL REPAIR TO BLDG NO. BK-29 AND BK-30 OF TRG CELL AT DRC UNDER AGE (I) AYODHYA CANTT.

Amount

Dismantling plain or corrugated Asbestos cement (Corrugated, semicorrugated etc) sheets in roof covering and S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA of AZ 150 as in roof covering/cladding to wall , fixed with self tapping screws, complete all as specified and directed.

Dismantling plain or corrugated Asbestos cement (Corrugated, semicorrugated etc) sheets in roof covering and S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA of AZ 150 as in roof covering/cladding to wall and rain water gutter fixed with self tapping screws, complete all as specified and directed.

Dismantling of framed work timber scantling 40 sqcm and over in section and in any position, complete all as specified and directed.

M&L for steel work in tubular trusses, door frame, column, railing, grills etc incl special shaped washer etc complete using ERW or induction butt welded tube confirming to IS 1161:1979 grade 240, complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in kerbs, PCC block for fixing rungs and coping including necessary form work, complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber pulp insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets,complete all as specified and directed.

S&F powder coated anodised aluminium snap grid frame work of grid size 605x605mm for false ceiling complete all as specified and directed by Engineer-in-Charge. Make:- Armstrong, Hi Steel.

S&F hanger 6mm dia GI (upto 3000mm length) ajusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold of grid size 605x605mm, complete all as specified and directed.

S&F 4mm thick high pressure steam cured Non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/Aluminium frame work with screws complete all as specified.

Dismantling wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises and M&L for glazed ceremic coloured tile in vertical surfaces 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl rendering 10mm thick in cm 1:4 on vertical surface of wall for fixing of wall tile, complete all as specified and directed.

Dismantling of floor tile including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises and M&L for Coloured Non skid Ceramic tile 7 to 8 mm thick 400x400 (Square) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bedding in CM 1:6, complete all as specified and directed

Roughening of stone surface including neat cement slurry @ 3 Kg/Sqm to receive floor finishes, complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20 mm thick laid over & including 15 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab in riser of steps, skirting, dado and pillar laid over & including cement screed 10mm thick in CM 1:4 & jointed with grey cement slurry mixed with pigment to match the smooth of the slab incl rubbing & polishing complete all as specified and directed.

Taking down cement plaster from brick or stone walls any description including raking out joints, hacking for key, scrubbing down with water to receive plaster removal of rubbish off the premises etc and M&L for rendering 15mm thick upto 5m height on fair faces of brick work or concrete surfaces in CM (1:4) finishing the surface even and fair without using extra cement, complete all as specified and directed. Note:- Plastering shall be done using coarse sand (reddish colour) only.

Taking down cement plaster from brick or stone walls any description including raking out joints, hacking for key, scrubbing down with water to receive plaster removal of rubbish off the premises etc and M&L for rendering 10mm thick upto 5m height on fair faces of brick work or concrete surface in CM 1:6 as in internal walls to be finished even and smooth without using extra cement, complete all as specified and directed. Note:- Plastering shall be done using coarse sand (reddish colour) only.

M&L for preparation of new plastered surface and applying two coat of oil bound distemper on walls over a coat of primer incl 1mm thick wall care putty, complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coat of oil bound distemper on walls over a coat of primer and 1 mm thick wall care putty complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings heads, shoes, bends, swan-necks, etc., incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) and S&F 110mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings heads, shoes, bends, swan-necks, etc., incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) and S&F 75mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F in repair 75mm PVC floor trap plain with grating including jointing with solvent cement, complete all as specified and directed.

M&L for Cutting chases pinning in , making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for concealed for water tubing or concealed condute wiring etc and making good, cutting n.exc 10cm girth, complete all as specified & as directed

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 15mm bore pipe and S&F 16 mm outer diameter CPVC Pipes SDR 11 & Plain CPVC SDR 11 fittings on wall/ceiling or laying in floors, complete all as specified and directed.

S&F in repair 15 mm size bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and directed.

S&F in repair 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pedestral pan white, including 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polythylene of low or high density or PVC 32mm dia, Plastic water closet seat, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hanging device, complete all as specified and as directed.

S&F brass chromium plated 2 way bib cock with wall flange 15 mm dia including fixing to pipe, complete all as specified and directed. Make : Jaquar Cat No. F-2008161 or equivalent cat part of make as specified in list of make.

S&F Health faucet brass body with 8 mm dia 1.00 m long flexible tube and wall hook including fixing, complete all as specified and directed.

S&F vitreous china wash hand basin white flat back size 550 x 400 mm excluding taps waste chain and plug but including bracket, waste coupling of 32 mm size fixed in repair, complete all as specified and directed by Engineer-in-Charge.

S&F brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges including brackets fixed to wall complete all as specified and directed

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) Area exc 1.5 Sqm but n exc 4.00 Sqm each, complete all as specified and directed.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete of size 125 X 60 mm complete all as specified.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete of size 105 X 60 mm complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed.

M&L for PCC 1:2:4 Type B0 ( 12.5 mm graded crushed stone aggregate) in filling under pressed steel door frame,lintel upto 1.5m clear span,cill, steps,seismic and other similiar bands, plinth courses,string courses, laacing courses parapets and railings upto 60 cm in height, bed plates, copings, kerbs, etc. water troughs and the like includind weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

S&F 35 mm thick factory made 2nd class hardwood with sash bars glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc edges of framing plain, chamferd or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.24(a), etc complete all as directed by Engineer-in-charge.

S&F 30mm thick factory made solid door with particle board core moulded design engraved moulded with plain sheet or sun mica sheet hydraulic hot pressed pasted with adhesives on both side & edges, complete all as specified and directed.

S&F for 300mm long MS ordinary rat tail rod pattern spring including roller and roller plate, complete all as specified and directed.

S&F 150mm long stainless steel handles for door, complete all as specified as directed by Engineer-in-Charge

S&F 200mm long stainless steel tower bolt complete all as specified as directed by Engineer-in-Charge.

S&F 300mm stainless steel sliding door bolt with hasp, staple (bolt type) and fixing complete set with nut and bolts, complete all as directed by Engineer-in-charge.

S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring, fixed in floor, complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

M&L for preparation of new wooden /wood based materials surfaces of any description , not otherwise described ,over 10 cm width or girth and painting two coats with synthetic enamel over a coat of pink primer, complete all as specified and directed.

M&L for preparation of old painted wooden /wood based materials surfaces of any description , not otherwise described ,over 10 cm width or girth and painting one coat with synthetic enamel including cleaning, stopping and rubbing down and removing all dropings etc., complete all as specified and directed.

Taking down chowkhat or frame (with shutter w/o taking of shutter from frame) n.exc 1.5 sqm each, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour pvc 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails,lock rail and bottom rail on either side and as gap insert for top rail and bottom rail,Panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement supply and fixing in the frame at site as per specification and drawing.

S&F 100mm long butt hinges medium grade stainless steel and fixed, complete all as specified and directed.

S&F 18mm thick PVC sheet minimum 600 Kg Density grade 1 quality of both side plain white colour rigid and glossy finish and fixed with epoxy coated screws solvent cement/adhesive as per manufacturer instructions to make kitchen cabinet/cupboard sides top and bottom shelves inside complete all as spd and directed.

S&F 18mm thick PVC sheet minimum 600 Kg Density grade 1 quality one side decorative lamination and other side plain white colour to make kitchen cabinet/drawer/cupboard shutters fixed with epoxy coated screws solvent cement adhesive as per manufacturer instructions to make kitchen cabinet sides, top and bottom shelves inside complete all as spd and direceted.

S&F auto closing hydraulic (Soft closing) chrome finish steel hinges openable at 110 degree all as specified and directed.

S&F 100mm long stainless steel grade-304 handle fancy type polished bright chrome finish, complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts 100 mm of extruded section and fixed, complete all as specified and directed.

S&F aluminium anodised Hasp and staple 75mm ,safety type brass hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F brass knobs 35mm to 40mm dia with fixing screews, complete all as specified and directed.

S&F in repairs vitreous china squatting pan, Orissa pattern, size 580 X 440 mm white, with integral foot rests (excluding cistern and flush pipe) but including connection to trap, and to flush pipe, anti-Syphonge pipe,and incl trap set in lime concrete etc complete including making good to floor complete all as specified and directed.

S&F in repair for 10ltrs PVC valveless,syphonic action type flushing cistern low level white with inlet,ball valve,float and handle including brackets complete all as specified and directed.

S&F for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for concrete bed to drain pipes of 100 mm dia including packing under and completely surrounding pipes with concrete after they are laid and tested in cement concrete 1:4:8 type D-2 complete all as apecified and directed

M&L for concrete bed to drain pipes of 150 mm dia including packing under and completely surrounding pipes with concrete after they are laid and tested in cement concrete 1:4:8 type D-2 complete all as specified and directed

Demolition and breaking up 150mm dia in bore drain pipes (salt glazed ware, AC or Reinforced concrete) set in cement mortar in any description complete all as specified and directed and M&L for Reinforced concrete pipes class NP2 of 150 mm dia laid and jointed complete with collars complete all specified and directed

All as per item No. 63 above but of 100 mm dia

M&L for Cutting into existing manholes for removing existing branch drain, making good to pipe and rendering cutting out branch channel, and making good benchings for 150 mm bore pipe, complete all as specified and directed.

M&L for pre-cast RCC 1:2:4 type B1 using 20mm graded stone aggregrate in cover slab for manhole or similar works set in CM 1:6 complete all as specified and directed by Engineer-in-charge. Note :- reinforcement shall be measured and paid separately.

Demolition of Brickwork/Stone masonary built in cement mortar including all quoins,arches,pillars etc but excluding ashlar facings,dressed stonework and precast concrete articles, complete all as specified and directed.

M&L for Brickwork with sub- class ‘B’ bricks straight or curved on plan exc 6 m mean radius in CM 1:6, complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on brick masonry surfaces to be finished fair and even, complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in plinth protection, finishing cement concrete surface even and fair complete all as specified and directed. Note:- Plinth protection will be laid in outward slope of 1in 12 and in alternative bays/panel. Length of panel shall not exceed 2.5 m and joint between two panel shall be filled with mastic filling comrimising mixture of one part of hot blown bitumen 85/25 penetration and two part of heated sand, complete all as specified and directed.

M&L for 4.8 mm thick sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for 4.8 mm thick frosted sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane, complete all as specified and as directed.

M&L for preparing new plastered or unplastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of not less than 01 mm thick wall care putty and including a coat of exterior wall primer, complete all as specified and directed.

M&L for complete removal of existing treatment of old plastered or unplastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of not less than 01 mm thick wall care putty and including a coat of exterior wall primer & complete removal of existing surface complete all as specified and directed. 1-Note-Exterior primer & acrylic emulsion paint to be applied on wall surface by using Airless spray technology with working pressure of 3300 PSI and capable of operating single spray gun with max material hose length of 30 mtr.The spray machine shouild be of reputed manufacturer with pro gaurd technology and capability of tracking pressure.2-Allow 6-8 hrs to dry the surface for painting of subsequent coat, complete all as specified and as directed.

S&F stainless steel curtain rod of 20 mm dia with fixing brackets, incl side brackets, finals, complete all as specified and as directed.

Providing and fixing factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. N exc 2.00 Sqm Each, complete all as specified and as directed.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid seprately).

S&F 1000 Ltr capacity white colour triple layer, rotational moulded polythene water storage tank hoisted and fixed on Roof/tank staging in position including all fitting such as connection pieces with GI tank nipple for inlet, outlet and overflow etc and including 20mm size ball valve high pressure of PTMT with appoxy coated aluminium Rod and high density plastic ball screwed for iron pipe complete and including dismantling of PVC water tank complete all as specfied and directed.

S&F 20mm dia Gun metal, globe of gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete all as specfied and directed.

S&F in repiar vitreous china urinal half stall complete incl providing and fixing plugs bedding urinal against wall in CM 1:2 securing urinal to plugs with and incl 60m long brass screws pointing around urinal in back in cement, fixing with flush pipe, grating and union for discharge pipe complete all as specfied and directed.

Hacking out old broken glass (any thickness, msize, quality or description) from metal frame including punching or drilling out old glazing pin and supply and fix 3mm thick glass in square n.exc 0.5 Sqm each pane with putty complete all as specfied and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors,and making good disturbed portion / surface of wall/ floor/ ceiling etc by using cement mortar (1:4) including white / colour wash / distempering etc as required to match with the existing surfaces / location, complete all as specified and as directed.

M&L for new concealed type point wiring with PVC insulated PVC unsheathed electric (FRLSH) copper wire of size 1.5 Sqmm nominal cross sectional area, 1100 Volt grade, single core having multi stranded copper conductor with 1.5 Sqmm green colour PVC insulated unsheathed electric (FRLSH) having multistranded copper conductor as earth wire connected to earth dolly by providing lugs including non-modular type GI sunken boxes suitable for non-modular switches/sockets etc with 3mm thick hylam sheet with glossy finish including necessary cutting for fixing switches, sockets, regulators etc, drawn through and including non metallic rigid PVC conduit (ISI marked) medium grade not less than 20mm dia with all conduit accessories in concealed wiring system including cutting chases in wall and making good in cement mortar (1:4) with all necessary surface finishes such as white / colour wash / distempering etc to match the existing surfaces complete all as specified for the following:-

All as per Srl item No. 79 above but for one light/fan point controlled by one, one way switch

All as per Srl item No. 79 but for One socket outlet point 6 A on same board

All as per Srl item No. 79 but for one socket outlet point 6 Amps on independent board

All as per Srl Item No. 2.00 here in before but concealed point wiring with 2.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed (FRLSH) cable and 2.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed (FRLSH) cable, green colour as earth continuity wire for 16 Amps power socket point controlled by one, one way 16 Amps non-modular switch on independent board complete all as specified and directed.

S&F switch piano flush type polycarbonate single pole one way 6 Amps complete all as specified and directed.

S&F switch piano flush type polycarbonate single pole one way 16 Amps complete all as specified and directed.

S&F socket outlet polycarbonate 2 in 1, 3 pin 6 Amps flush type complete all as specified and directed.

S&F socket outlet polycarbonate 2 in 1, 3 pin 6/16 Amps flush type complete all as specified and directed.

M&L for ceiling rose in polycarbonate 3 terminal brass flush type 6 Amps, 250 Volts, AC supply (ISI marked), fixed on & including 3 mm thick 75mm dia sunmica hylum plastic laminated round sheet complete all as

S&F electronic fan regulator 230 Volts, stepped type hum free 100/300 watt, complete all as specified and directed.

Taking down Old unserviceable sub main wiring any size, complete all as specified and as directed.

M&L for sub main wiring with two runs of 10.00 Sqmm (nominal cross-sectional area) FRLSH PVC insulated & unsheathed 1100 Volts grade multistranded copper conductor single core drawn through and including PVC concealed conduit of adequates size and fittings and accessories concealed in walls, floors and ceilings complete including one run of FRLSH PVC insulated & unsheathed single core multistranded copper conductor cable of size 10.0 Sqmm green in colour as earth continuity conductor connected to common earth dolly from main DB to Sub DB including cutting chases and making good in cement mortar (1:4) with all necessary surface finishes such as white / colour wash / distempering etc to match the existing surfaces complete all as specified. Note:- (i) Two runs of cable, one run of earth wire and one run of PVC non metallic conduit shall be measured as one run length. (ii) Cable required for connection to DBs and MCBs shall be deemed included in quoted rates. (iii) Earth wire shall run inside the conduit pipe.

Taking down unserviceable main switch, DB’s insulators, DB for MCB and board etc of any type and any capacity and further disposal including making good the disturbed surfaces in cement mortar (1:4) including applying white/colour wash / paint / distemper as required to match the existing surfaces complete all as specified and as directed.

S&F epoxy powder coated MCB distribution box double door TPN 4 way vertical type for MCBs alongwith provn of MCB as incomer with common bus-bar at incoming end of outgoing MCCBs grouted / flush to wall including necessary cutting and making good disturbed surfaces in cement mortar (1:4) and applying white/colour wash / paint / distemper as required to match the existing surfaces complete all as specified and directed.

S&F of MCCB 4 Pole, 415 V, adjustable type thurmal magnitic ICS100%, 125 Amps with breaking capacity 36 KA as per existing MCB suitable of size with connected assosieries etc. Complete all as specified and as directed.

S&F MCB SP 40 Amps, 230 Volts C curve 10 KA, including necessary connection complete all as specified and as directed.

Supply and fix epoxy powder coated MCB, DB, double door SPN 8 way for MCBs with copper rated bus bar and IP 43 protection at incoming end of outgoing MCBs grouted/ flush to wall, Complete all as specified and as directed.

S&F MCB SPN 32 Amps, 230 Volts 'c' curve10 KA, including necessary connection complete all as specified and as directed.

Supply and fixing MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position all as specified and as directed.

S&F lamp holder PVC/ Polycarbonate type with 9 W Led Bulb back plate suitable for batten fittings complete all as speicfied.

Taking down old unserviceable light fitting any type, complete all as specified.

S&F LED batten Tube Light surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption <20W (4 feet 20 W) luminaire lumen >2000 lm, system efficiency of >120 lumens /W, with LED binning as per ANSI Bin C78.377A, photo biological safety report as per IEC624718 & electrical insulation class I, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 450C, driver efficiency>85%, power factor>0.9, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV, 50000 burning hrs (min) as per L70 criteria, two stages isolated constant current operated driver with range 150-270V AC and safety extra low voltage safe level <60V DC as per IEC standard with LM70 & LM80 certification. complete all as specified and directed.

S&F LED batten Tube Light surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption <10W (2 feet 10 W) luminaire lumen >1000 lm, system efficiency of >120 lumens /W, with LED binning as per ANSI Bin C78.377A, photo biological safety report as per IEC624718 & electrical insulation class I, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 450C, driver efficiency>85%, power factor>0.9, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV, 50000 burning hrs (min) as per L70 criteria, two stages isolated constant current operated driver with range 150-270V AC and safety extra low voltage safe level <60V DC as per IEC standard with LM70 & LM80 certification. complete all as specified and directed.

Supply and fixing inverter batten with square profile and polycarbonate channel lithium ion 1 battery with charging time 08hrs-100hrs and backup time up to 4 hrs indoor luminaire batten for wall / ceiling mounting box type energy efficient saving led batten light 20 watt including twin twisted copper conductor flexible wire from ceiling rose to connected complete all as specified and directed

Taking down fan, ceiling cable end,dismantling blades and removing fan and blades to MES store complete all as specified.

Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and as directed.

S&F Exhaust fan steel body AC single phase 230 V of size 300mm switch with blades and frame and louvers including making hole in wall, complete all as specified and as directed.

S&F electric water heater storage type steel body with heating element up to 2 KW capacity 50 liters five star ratings, complete all accessories such as safety valve thermostate, NRV, connection pipe etc, complete all as specified and as directed.

Taking down existing earthing of any description and M&L for new earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to GI earthing wire 4mm dia size by means of GI bolts, nuts, check nuts and washers, earthing wire protected by GI pipe 20 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6) type C1 in chamber of size not less than 300x300x300mm (internal diamentions) with cover made of RCC (1:2:4), type B-1, reinforced with 8 mm dia TMT bars @ 15 cm C/C both ways and angle iron 40X40X5mm frame etc duly painted with two coats of synthetic enamel paint over a coat of red oxided primer on exposed surfaces complete all as specified and directed by Engineer-in-Charge. Note: The unit rate includes earthing wire and protection pipe upto maximum 7.5 metre from earth plate, earth point / test point.

M/s R.S. Enterprises (BID ID -3405530)

Channa Brothers and Co. (BID ID -3405268)

M/S CHANDRIKA PRASAD AND SONS (BID ID -3404619)

M/S A P CONSTRUCTION (BID ID -3403256)

Ashirwad Contractor and Supplier (BID ID -3402676)