Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹68.6 LAccepted-AOC | L1 | Accepted-AOC Awarded | |
| 2 | L2₹77.1 L+₹7.1 L (10.2%)Rejected-Finance | L2 | Rejected-Finance 2nd Lowest | |
| 3 | L3₹77.3 L+₹7.3 L (10.4%)Rejected-Finance | L3 | Rejected-Finance 3rd Lowest | |
| 4 | L4₹79.1 L+₹9.1 L (13.1%)Rejected-Finance | L4 | Rejected-Finance 4th Lowest | |
| 5 | L5₹83.0 L+₹13.0 L (18.6%)Rejected-Finance | L5 | Rejected-Finance 5th Lowest |
Tender Value
Refer Docs
EMD Value
₹1.6 L
Closing Date
11 May 2022, 4:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Executive Engineer Division No-IHPPWD Shimla-3
Executive Engineer Division No-IHPPWD Shimla-3
Improvement of Junction Auckland Tunnel on MRR via Lakkar Bazar (SH Widening of Chowk , C/O Rain shelter (Near Proposed sub way)(Near Auckland (Under Shimla Smart city).
2022_PWD_60017_2
SD-I-CTR-Tender-1471 dated 27-04-2022
Open Tender
Civil Works
Item Rate
90 days
Shimla
As per SBD
14 documents required · 14 mandatory
₹2,000
₹1.6 L
8 May 2024
30 Apr 2022
12 May 2022
30 Apr 2022
11 May 2022
30 Apr 2022
75 days
Amount
Cutting and disposal of earth work in by mechanical in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting of to the required lines, levels as shown on the drawing and directed by the Engineer -in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site as per satisfaction of Engineer- in -charge through all modes of transportation including head load ,animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour ( if required ). The recovery for stones, whether use full or not for 25.58.cum(Twenty five point five eight cubic metre) @ 300/-only(Rupees three hundred only) per cubic metre shall be effected on prorata basis in all circumstances. All the surplus excavated earth to be dumped at dumping site(dumping sites will be arranged by the contractor on his own cost). Any loss to the public and private propriety, human being, machinery during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.
Earth work in excavation for structure in all depths as per drawing and technical specification for rural roads August 2004 clause 305.1 including setting out, construction of shoring abd bracing, removal of stumps and other deleterious materials and disposal in all leads and lift including dressing of sides and bottom and back filling in trenches with excavated suitable materials. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion damage to hill side water pollution etc. and to protect stability of hill side rock shall be excavated with chiseling and wedging out rock (where balsting is prohibited) all earth work in cutting/ excavation including rock excavation shall be carried out true to lines grades, side slopes, width , camber super elevation and level as shown on the drawings or as directed by the Engineer-in-charge hauling and stacking of materials useful for construction at suitable sites and safe disposal of unsuitable cut materials in specified dimension or as directed by the Engineer-in-Charge. If the foundation of the structure is in an area with stagnant water or water is met with in the excavation due to spring seepage rain and other causes it shall be remove by suitable diversion bailing out or pumping as directed and the area of the foundation or embankment shall be kept dry. All the surplus excavated earth to be dumped at dumping site(dumping sites will be arranged by the contractor on his own cost).Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be dully compensated by him at his on cost in all cases including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing and Laying cement concrete 1:4:8 for plain/reinforced concrete in open foundations complete as per drawing and technical specification clauses 802, 803, 1202 and 1203 including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Supplying, fitting and placeing HYSD bar reinfocement (Fe-415) in substructure complete as per drawing and technical specification Clauses 1002,1010 and 1202 including carriage of material in all leads and other incidential and as per direction of Engineer-in-Charge.
Plain/renforced cement concrete in substructure complete as per drawings and technical specification Clauses 802,804,805,806,807,1202 and 1204 including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. III. P.C.C. grade M 20 ( i) Nominal mix (1:2:4)(one cement: two sand :four graded)upto all height
Stone soling properly hand packed filling interstices with Kharanja stone and including watering and ramming consolidating with hand durmet complete under floor to the requisite gradient and camber including spreading watering and rolling of binding materials complete as per HP PWD specification including carriage of complete as per HPPWD specification including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Stone filling Behind Retaining wall including carriage of materials in all leads and lifts as per the directions of the Engineer-in-Charge
Providing weapholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm(One hundred milimetre) dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 including carriage of materials in all leads and lifts as per the directions of the Engineer-in-Charge.
Providing and Fixing Single "W" Metal beam crash barrier comprishing of cold formed W profiled section having thickness of 3 mm (three milimetre)(uncoated thickness ) with frame width of 311 mm(three hundred eleven milimetre) depth 83 mm (eighty three milimetre)and length 4318 mm(four thousand three hundred eighteen milimetre) (made of ISI marked HR coil conforming to IS : 5986/2011) , to be fixed on cold formed channel section post of size 150x75x5 mm (One hundred fifty into seventy five into five milimetre)( Made from ISI marked Hr Coils conforming to IS 5986/2011) spaced 1.50 metre(one point five zero metre) centre to centre of the post which will be of total height of 1.80 metre(One point eight zero metre) with its height of 1.1 metre(One point one metre) below ground level and 0.70 metre(zero point seven zero metre) above ground level. Metal beam rail to be fixed on the vertical post with spacer channel of cold formed channel section size 150x75x5 mm and 330 mm(One hundred fifty into seventy five into five milimetre) and (three hundred thirty milimetre) long (made from ISI Marked HR coils conforming to IS : 5986/2011 ) , All the above components shall - conform to clause 810 of MORTH & H specifications including all fittings required for erection on road side W-Beams, Posts , Spacers shall be hot dip galvanised with Zinc coating of 550 gm/Sqm(five hundred fifty gramt/swquare metre). All bolts , nuts and washers shall be hot dip galvanised to IS :1367 pt-XIII/1983 ( Reaffirmed 2011 ) for bolts and IS 14394/1996 (reaffirmed 2011 ) for nuts including carriage of materials in all leads and lifts as per the direction of Engineer-in- charge.
Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm(One point five milimetre) thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm (sixty five milimetre)width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 (forty seven milimetre into forty seven milimetre into twelve) SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm(four hundred fifty into four hundred fifty into six hundred milimete,six hundred milimete) below ground level as per approved drawing Clause 1701.2.2 including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i)(600 mm(six hundred milimete equilateral & triangle)
Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm (One point five milimetre)thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm (sixty five milimetre) width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12(forty seven milimetre into forty seven milimetre into twelve) SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm (four hundred fifty into four hundred fifty into six hundred milimete,six hundred milimete)below ground level as per approved drawing Clause 1701.2.2 including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i)( 600 mm (six hundred milimete)circular )
Providing and erecting direction and place identification of semi reflective sign boards as per IRC-67 made of 2 mm(two milimetre) thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm(seventy milimetre) width and required message, letters, figures with reflective tape of engineering grade as per MORD specifications of required shade and colour. Supported and welded on two nos. 47 mm x 47 mm of 12 (forty seven milimetre into forty seven milimetre into twelve) SWG square tube of 3050 mm (three thousand fifty milimetre) height duly strengthened by 25 mm x 5 mm (twenty five milimetre into five milimetre) MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm(four hundred fifty into four hundred fifty into six hundred milimete,six hundred milimete) below ground level as per approved drawing and Technical Specification Clause 1701 including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) Direction and place indentification signs more than 0.9 sqm (zero point nine Square metre)size board
Filling in plinth with sand under floors including watering, ramming , consolidating and dressing complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing and laying cement concrete 1:6: 12(One cement: six sand: twelve graded stone agg.40mm nominal size)and curing complete excluding cost of centring and shuttering including Mixing & Vibrating charges including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) Foundation and plinth.
Random rubble masonry/polygonal rubble masonry(un-coursed/brought to courses) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement:Six sand:twelve graded stone aggregate 20mm (twenty milimetre)nominal size) in cement mortar 1:6 (One cement: Six sand) in breast wall and retaining walls including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Second class brick work using common burnt clay building bricks in super structure upto all floor level in cement mortar 1:5(one cement is to five sand) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing and laying damp proof course 38mm(thirty eight milimetre) thick with cement concrete 1:2:4 (one cement:two sand:four stone aggregate 12.5 mm (twelve point five milimetre)nominal size) and curing complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Applying a coat of hot bitumen(mexphalt 80/100 (eighty/one hudnred)or equivalent) using 1.70 Kg.(one point seven zero kilogram) per square metre on damp proof course after cleaning the surface with piece of cloth lightly soaked with kerosene oil including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing form work with steel plates (3.15mm) (three point fifteen milimetre) thick welded with angle iron in frame (30x30x5mm) ( Thirty x thirty x 5 milimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc., with wooden battens and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4mtr.(Four metre) and removal of the same for insitu-reinforced concrete and plain concrete work including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a). Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.
Providing mild steel/tor steel reinforcement for RCC work i/c bending, binding & placing in position including cost of binding wire complete up to all floor level/all heights including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing and laying marble work (table rubbed and polished) in flooring laid over 20mm(Twenty milimetres) thick base in 1:3 (One cement :three sand) including jointed with cement mortar 1:2(one white cement :two marble dust) with an admixture of pigment to match of the shade of marble 20mm (Twenty milimetres) thick makrana marble including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing 25mm(Twenty five milimetres)thick kota stone single slab with round nosing over heads of steps and landings on a bed of 12mm(twelve milimetre) (Average) thickness cement mortar 1:3(One cement :Three sand) and jointed with Grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing and fixing mild steel hollow pipe 100mm(One hundred milimetre) dia heavy grade embedded in cement concrete masonry work and filled with cement concrete 1:3:6 (One cement :three sand :six graded /crushed stone aggregate 20mm(twenty milimetre) nominal size) within all leads and lifts of material and other including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing and fixing 0.60mm(zero point six zero milimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.
Providing and fixing ridges or hips 60 cm (sixty centimetre)overall with 0.60mm (zero point six zero milimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges.
Providing and fixing M.S. BP Sheet 1.66mm to 20mm(One point six six to twenty milimetre) thick in eaves board/facia/ soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)
Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i)In trusses and trussed purlins in buildings.
Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.(i)With ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome.
Painting two coats (excluding priming coats) on new steel and other metal surfaces under coat with ready mixed paint with enamel paint brushing to give an even shade including cleanign the surfaces of all dirt,dust and other foregin matter including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) With enamel paint other than white.
15mm (fifteen milimetre)Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth and finished even and smooth including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) Cement Mortar 1:6 (One Cement:Six Sand).
Applying priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering as required with including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) Readymixed primer
Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Wall painting (wo coats) with synthtic emulsion premium (Komosilky) of Kamdenu emulsion paints of approved brand and manufacture for interior grade on undecorated concrete/stone /plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing under layer for plinth protection of 75mm (seventy five milimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm(forty milimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Providing plinth protection 50mm (fifty milimetre) thick in cement concrete 1:3:6(One cement: three sand: six graded stone aggregate 20mm(twenty milimetre) nominal size) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.
Precast terrazzo chequred tiles 20 mm(Twenty milimetre) thick with out marble chips of specified sizes laid in floors, treads of steps and landings on a bed of 25 mm(twenty five milimetre) average thickness of cement mortar 1:6 (one cement :six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) incliding rubbing and polishing complete with tiles of following shades including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. i)Grey/Red/Yellow ( NTC)
VIKRAM SINGH GOVT. CONTRACTOR
MANTU KUMAR GUPTA
Sandeep Chandel
Hari Bhushan
DASU RAM
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .