REPAIR/MAINT TO BRICK WORK, PLASTERING, TILING, SANITARY ITEMS, PLUMING WORK, PLINTH PROTECTION, SEWAGE DISPOSAL, MECHANIZED PERIODICAL SERVICES AND MISC B/R WORKS AT CMDC, SOI AND MESS, SURYA AUDITORIUM, PUNIT DUTT AUDITORIUM, MP SWIMMING POOL

Amount

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed.

M&L for Brick work with Fly ash brick designation 100 Kg / Sqcm, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, using bricks of size 230 mm x 110 mm x 70 mm confirming to IS 12894, complete all as specified and as directed by Engineer-in-Charge.

M&L for Brick work in half brick thick wall with Fly ash brick designation 100 Kg / Sqcm, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4, using bricks of size 230 mm x 110 mm x 70 mm confirming to IS 12894, complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level), complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone agg, as in florring, finished even and smooth without using extra cement all as specified and as directed.

M&L for plain cement concrete 1:2:4, type B-1, using 20 mm graded stone aggregate as in roof kerbs / padding or similar work or mud stops rounded or chamferred on edges.

M&L for plain cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in coping, padding and bed block, wall through and the like including weathering slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C2, using 40 mm graded stone aggregate, as plinth protection / path and the like, finished even and smooth without using extra cement all as specified and as directed.

M&L for filling joints of size 10 mm x 75 mm between two concreat panels with mix of 85 / 25 bitumen and sand in 1:3 complete all as specified and directed by Engineer-in-Charge

M&L for precast cement concrete Type B0,1:2:4 (using 12.5mm graded stone aggregates) louvres and jallies, 25mm thick (measured solid), including all mouldings and set in CM 1:4 complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for providing precast cement concrete type B0, 1:2:4 (using 12.5mm graded stone aggregates) as in win dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match including set in CM 1:4, complete all as specified and directed.

M&L for type B1 1:2:4 (using 20 mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and chajja and the like incl necessary form work complete all as specified and directed.

M&L for mild steel TMT reinforcement bars of grade FE-500, 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. or securing with clips complete all as specified and directed by Engineer-in-Charge

All as per item No 14 above but 8 mm dia and over upto and including 10mm dia in stirrups, spacers and binders

Taking down chowkhats or frame (wooden/aluminium) n. exc. 1.5 Sqm each with shutters (with out taking off shutters from the frame) and taken as credit complete all as specified and directed.

Taking down chowkhats or frames (wooden/aluminium) with shutters without taking off shutter from the frames exc. 1.5 but n. exc 4 sqm each complete all as specified and directed.

Taking down shutters of any description n exc 1 sq.m each complete all as specified and directed.

Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each complete all as specified and directed.

S&F well seasoned 2nd class hard wood plan, solid, straight chowkat and frames, wrought framed, rebate on the solid rounded or chamfered, put together with glue pinned at joint complete all as specified and directed.

M&L for Pressed steel frames 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, lock strike plates complete, providing mild steel 6 mm dia thresh old bar, thickness of sheet 1.25 mm and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) complete, all as specified.

M&L for Pressed steel frames 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, lock strike plates complete, providing mild steel 6 mm dia thresh old bar, thickness of sheet 1.25 mm and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) complete, all as specified.

S&F for Mild steel work Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 as in small articles like angle iron framing work for manhole, rungs/steps in man hole complete all as specified and directed.

M&L for preparing new surfaces of wood and wood based marterial, steel and iron works of any description and girth treating ends of post back of chowkats or hold fasr etc, area tarred exc 0.1 sqm but n exc 0.5 sqm each with tar or coal tar black paint complete all as specified and directed by Engineer-in-Charge

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.23(b) complete all as specified and directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise desceribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and directed.

S&F 100mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed.

S&F 75mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed.

S&F for PVC door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F for factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F 250 mm aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 100 mm length of bolt complete all as specified and directed.

S&F 150 mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repair for 150 mm floor door stopper of aluminium alloy body and tonge,anodised with hard drawn steel spring, complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone, concrete or bricks round, glazed with putty or fixed with bedds complete all as specified and directed.

S&F for 3.0 mm thick sheet glass ordinary quality and glazing with oil putty nexc 0.5 Sqm each pane, complete all as specified and directed.

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty n.exc 0.5 Sqm each pane, complete all as specified and directed.

S&f for 4.8 mm thick sheet glass odinary qulity and glazing with neosprene beading n.exc 0.5 Sqm in each pane, complete all as specified and directed.

M&L for 12 mm thick pre-laminated Medium Density board, both side decorative lamination interior grade, fixed in aluminium / wooden frame work, complete all as specified and directed.

Taking down Neoprene rubber beading with glass from aluminium joinery and refixing of glass in same opening with new Neoprene rubber beading complete.

S&F 12 mm thick toughened glass ordinary quality and fixed to aluminium joinery with and including neoprene beading, SS clip or cleats of any size any position including taking down of existing unserviceable glass.

M&L for Repairing of existing aluminium door single / double leaf (area of each leaf exc 1 Sqm but n.exc 2.0 Sqm) by taking down tightening of joint, tightening of top & bottom patch, replacement of cleat, screw, oiling and greasing of floor springs, & refixing in same opening for smooth functioning complete all as specified. Note:- Floor door springs where renewed shall be measured and paid separately under appropriate item of BOQ.

M&L for Repairing of existing toughened glass door single leaf (area of each leaf exc 1 Sqm but n.exc 2.0 Sqm) by taking down tightening of joint, tightening of top & bottom patch, oiling and greasing of floor springs, & refixing in same opening for smooth functioning complete all as specified. Note:- Floor door springs where renewed shall be measured and paid separately under appropriate item of BOQ.

S&F in repair Double action floor spring hydraulically regu-lated made up of minimum 1.25 mm thick alu-minium alloy sheet foun-dation box,main body with stainless steel cover, governing pivot made of mild steel heavy duty fixed, complete all as specified and directed.

S&F in repairs Aluminium body ( extruded section ) body Door closer hydraulically regulated, designation No. 2 , universal type , suitable for door shutters 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed, complete all as specified and directed.

S&F in repair for 100 mm mild steel 4 lever mortice lock vertical type of size of brass body, complete all as specified and directed.

S&F for anodised aluminium frame for doors, windows, ventilators, partition section with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F for anodised aluminium work for doors, windows any type sliding or fixed, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge, complete all as specified and directed.

S&F for powder coated aluminium frame for doors, windows, ventilators, partition section with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.

S&F for powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge, complete all as specified and directed.

S&F in repairs aluminium anodized grill with suitable aluminium anodized frame of F/H section with suitable fixing screws/attachment etc complete all as per M/S Deco Grill Design No DG -102 , 7.5mm size grill i.e. made out of 75mm thick aluminium plate all as per manufacturer's specifications, complete all as specified and directed.

S&F in repairs powder coated aluminium grill 3.13 Kg per Sqm (min) with grill frame of 0.297 Kg per meter (min), (Design as approved by Engr-in-charge), complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and directed.

M & L for Super heavy series PVC Wall panelling/Lining consisting of 5mm thick Plain/wood colour PVC sheet as approved inclusive of solvent cement and fixing at site on PVC frame including complete fixing arrangments on wall complete all as per manufactures specifications, complete all as specified and directed.

S&F for providing and fixing of E-board 600 x 600 x 4 mm thick white prelaminated seif embosed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24 mm wide T-section / Angle section complete all as specified and directed.

M&L Suspended ceiling, comprising 12.5 mm thick reinforced gypsum plaster boards Conforming to IS-2095 , GI perimeter channels, intermdiate channels, etc. including finishing the exposed surfaces with Oil bound distemper two coats complete all as specified and directed.

M&L false ceiling, with and including GI powder coated frame work and mineral fiber ceiling tiles , suspended with ceiling in and including of dismantling of ceiling boards (fiber, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, (Working up to 10 mtr height), complete all as specified and directed.

S&F for 3mm thick aluminium composite panel with aluminium frame and glazing clip and neosprene rubber beading complete all as specified and directed.

M&L for taking down, chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC Columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement and quartz sand mortor in CM 1:3 mix , 40mm thk in two coats, using polymer @ 10 to15% by weight of cement complete & finally finishing the surface complete all as specified and directed. (Note :- New reinforcement and MS Sections will be measured and paid separately)

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified and directed.

M&L for Rendering 15 mm thick in cement and sand mortar 1:4 on brick work or cement concrete wall surfaces, finishing the surface even and smooth without using extra cement including mixing only liquid water proofing compound as per manufacturers instruction complete all as specified. (WPC will be measured and paid separately)

M&L for Rendering 15 mm thick in cement and sand mortar 1:6 on brick work or cement concrete wall surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

M&L for Rendering 10 mm thick in cement and sand mortar 1:6 on brick work or cement concrete wall surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surface of ceiling, finished even and smooth without using extra cement.

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying three coats white wash complete all as specified and directed.

M&L for Preparation of newly plastered surfaces and applying two coat of oil bound disemper over one coat of primer all as specified on walls surface.Incl a coat of 3 mm wall care putty, complete all as specified and directed.

M&L for preparation of new plastered surafce of walls and applying two coats exterior emulsion weather coat paint of make Apex (Asian Paint) / Weather coat (Berger) / Excel Top Guard (Nerolac) over one coat primer including 1 mm thick wall care putty complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint of any tint/shade complete all as specified and directed.

Demolition of existing roof treatment of any type, complete all as specified and directed.

M&L for 15 mm thick screed bed in cement mortar 1:4 over RCC roof slab including mixing olnly liquid water proofing compound as per manufacturer instruction complete all as specified and directed by Engineer-in-Charge. (WPC will be measured and paid separately)

Supply only Liquid water proofing compound.

M&L for water proofing treatment on roof surfaces in the following manner:- (a) The surfaces shall be painted with hot bitumen grade 30/40 confirming to IS-73 @ 1.20 kg / sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 ltr /sqm. (b) Supply & lay 3 mm thick APP water proofing membrane reinforced with non woven polyster matt laid using butane torch by torch application with a side lap of 10 cm & 15 cm end lap weinghing not less than 3.5 kg / sqm. Note: - (i) Work to be carried out through authorised applicators of the manufactures and work will be carried out in complete / in patches in roofs (ii) Contractor shall submit written gurantee of 10 years from date of completion & submit security deposit @ 2.5% of executed amout or Rs 6250.00 which ever is more.

M&L for applying two coats of aluminium paint over APP membrain including preparation of surfaces and primer.

M&L for 40 mm thick brick tiles laid over & including screed bed 15 mm thick in cement mortar in 1:4 and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement.

Demolition of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debries to a distance exc 1.5 km but n.exc 5 Km

M&L for non skid ceramic tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles laid over and including 15 mm thick screed in CM 1:6, complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surfaces, of size 450 mm x 300 mm x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles laid over and including 10 mm thick screed in CM 1:3, complete all as specified and directed.

S&F for glazed ceramic tiles 6-7 mm thick in swimming pool floor & vertical surfaces set matching with previous size and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles laid over and including 15 mm thick screed in CM 1:3 complete all as specified and directed.

M&L for vitrified ceramic tiles 10 mm thick (square /rectangular ) polished dark shade, area of each tiles not exceeding 0.36 sqm, in floor etc. set and jointed in neet cement slurry and pointed white or coloured cement to match the shade of the tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

All as per item No 84 above but as in skirting but laid over and including 10 mm thick rendering in CM. 1:4 as backing coat etc

Dismantling stone slab and tiles of any description or and thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 18-20mm thick machine cut Kota stone slab flooring with marble stone strips / slab / tiles as per design approved, laid over and including cement screed bed 20 mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, & polishing complete all as specified and directed.

M&L for 18-20 mm thick machine cut Kota stone slab as in skirting /riser laid over and including backing coat 10 mm thick in CM 1:3, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

Grinding of old kota stone flooring with floor grinding machine upto mirror finish level including polisihig etc complete all as specified and directed.

M&L for 18 to 20 mm thick granite (of any type) tiles machine cut & machine polished, set & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone laid over and including screed bed 15 mm thick in cement mortor 1:4 complete all as specified and directed.

Taking up or down 15 mm bore steel tubing including all fitting & fixture complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20 mm bore steel tubing including all fitting & fixture complete all as specified and directed by Engineer-in-Charge.

Refixing old steel tubing and connections in new or old position (walls, ceiling , floors, etc) 15 mm nominal bore complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) 20 mm nominal bore complete all as specified and directed.

M&L for 15 mm bore mild steel galvanised water tubing, medium grade, with all fittings and fixture, fixed to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm bore mild steel galvanised water tubing, medium grade, with all fittings and fixture, fixed to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Supply and fix 500 litres capacity double layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc including taking down old tank complete.

Supply and fix 1000 litres capacity double layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc including taking down old tank complete.

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete all as specified and directed.

S&F in repairs Chromium plated fancy long body Bib taps with cup, cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair brass chromium plated shower roses with swil joints, 80 mm size in square with long shank arm including fixing to steel pipe or union, complete all as specified and as directed.

S&F in repairs Chromium plated,Concealed stop cock Reduced body ISI Marked, , cast copper alloy, screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repair CP Angle stop cock (one way) long thread with wall flange , fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repairs Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed.

S&F in repairs PTMT( Polytetra Methyllene Terephthalate )Bib taps suitable for 15 mm bore pipe standard of PTMT any colour screwed, for iron pipe and fixed (Minimum weight 15 mm-90 gms) complete all as specified and directed.

S&F in repairs CP Angle stop cock( two way) long thread with wall flange , screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repairs, 100 mm dia stainles steel chromium plated grating, fixed in position with white cement Complete.

S&F in repairs Chromium plated Brass Tubular towel rod, of 24" (60 cm long) complete all as specified and directed.

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, including all connection complete.

Supply and fix in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580 mm x 440 mm white with integral foot rests with ‘P’ or ‘S’ trap, front or back inlet including all connection and provision of lime concrete base complete all as specified and as directed..

S&F in repair PVC low level flushing cistern, valveless, syphonic action type, double push botton, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 32 mm dia of required length and making connection complete complete all as specified.

S&F in repairs Plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs PTMT connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white ( minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe, and waste pipe), fixed in repairs including connections to flushing pipe complete all as specified and directed.

Supply and fix in repair white vitreous China wash hand basin (Flat back) of size 550 x 450 mm fixed on and including new brackets complete including, 32 mm size brass chromium plated waste coupling, chain and plug and porcelain stopper, etc complete.

S&F in repair 32 mm bore flexible pipe of PVC fixed to WHB / urinals as waste pipe (not less than 600 mm) including PVC coupling complete all as specified and directed.

S&F in repairs 32 mm waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repair 20 mm size Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm size Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repair white vitreous china floor mounted coupled EWC of size 380 mm x 725 mm x 690 mm including UF soft close slim seat cover, hinges, fixing accessories, accessories set and Cistern with fittings complete all as specified and directed. Make of Cistern & EWC: Jaquar model No-ONS-WHT-10853S300UFSM or equivalent cat No of make mention under list of make.

S&F in repair cast iron floor trap with chromium plated grating including jointing to waste pipe wih cement mortar (75 mm bore of pipe), complete all as specified and directed.

S&F in repair brass chromium plated Health faucet fixed with spring action and lever along with Flexible hose with brass nut of length 1 m to 1.2 m fitted in the existing water connection in the toilets, Complete all as specified and directed by Engineer-in-Charge.

S&F in repairs overhead shower of 100 mm dia round shape single flow (ABS Body Chrome Plated with Gray Face Plate) with rubit cleaning system complete all as specified and as directed

S & F in repairs 15 mm size single lever wall mixer with provision for hand shower, for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for 15 mm size bib taps, two way, fancy type, cast copper alloy chromium plated, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repair for chrominium plated towel ring of circular / oval / rectangular shape with complete fixing arrangments to wall, complete all as specified and directed.

S&F for corner sheet glass shelf of 4.8mm thick fixed with Stainless steel clamps and other necessary fittings suitable for holding in wall corner with minimum 200 mm length in front circular shape, complete all as specified and directed.

S&F for sheet glass shelf of 4.8mm thick fixed with Stainless steel clamps and other necessary fittings suitable for holding in wall of minimum size 300x150mm, complete all as specified and directed.

Taking down pipes (any sizes) including all fittings, complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls, with PVC clamp all as specified.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth,and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old painted surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint / shade complete all as specified and directed.

M&L for preparation of old painted surfaces of walls by washing, rubbing down & stopping etc, and applying two coats of cement base paint of any tint / shade complete all as specified and directed.

M&L for preparation of old painted surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade complete all as specified and directed.

M&L for preparation of old painted surfaces of walls by washing, rubbing down & stopping etc, and applying two coats of distemper oil emulsion of any tint/shade complete all as specified and directed.

M&L for preparation of old painted surfaces of ceiling by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint / shade complete all as specified and directed.

Excavating in post holes each not exc. 0.5 cum getting out in soft / loose soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc. 25 cm, watering and removing surplus soil to a distance not exc. 50 m and depositing where complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 as in foundation and mass concrete using 40 mm graded stone, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

S&F steel work in tubular trusses/posts including special washers etc complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St-240, complete all as specified and directed.

S&F rolled mild steel section as in main and cross beams, hip and jack rafters; purlin where connected to common rafters and running rails and guides for for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410-W (Gde-E-250 quality A).

M&L for preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling of roof sheet (any descriptions) including ridges in roof covering complete all as specified and directed.

S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F 2mm thick fibre glass reinforced transclucent corrugated sheeting with two corrugations side lap fixed with L type or J- type or cranked hook bolts and washers in roof, wall etc complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement including taking down, complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8, type D-2,(using 40 mm graded stone aggregate) as in Sub base for path / flooring complete all as specified and as directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L Chequered cement concrete coloured tiles 30 cm x 30 cm x 20 mm thick with gray cement and pigment, set, jointed and pointed in neat cement slurry laid over and including 15 mm thick screed bed in CM 1:4 as in floors complete all as specified and directed.

M&L for exterior grade outdoor coloured floor tiles (heavy duty) of tactile series of size 300 x 300 x 10 mm of Make Johnson endura or equivalent make mention in list of amke, laid over and including 15 mm thick screed bed in CM 1:6 and jointed in cement mortar to match the colour of floor complete all as specified and directed.

Temporarily blocking and cleaning of inlet of septic tanks/manhole with suitable wooden plugs/gunny bags and pumping/bailing out effluent and taking out/removing the accumulated sludge soil sewage/any other foreign/foul materials etc (solid/semisolid) from the septic tanks/manholes. complete and cleaning the septic tank/manholes with water by mechanically including taking out the blocking arrangements of inlet and making the system functional complete all as specified and directed. NOTE: (i) Depth of manhole/SOAK WELL/SEPTIC TANK exc 0.5 to 1.5M from below GL (ii) Size of tank upto water level shall be measured

Temporarily blocking and cleaning of inlet of septic tanks/manhole with suitable wooden plugs/gunny bags and pumping/bailing out effluent and taking out/removing the accumulated sludge soil sewage/any other foreign/foul materials etc (solid/semisolid) from the septic tanks/manholes. complete and cleaning the septic tank/manholes with water by mechanically including taking out the blocking arrangements of inlet and making the system functional complete all as specified and directed. NOTE: (i) Depth of manhole/SOAK WELL/SEPTIC TANK exc 1.50M to 4.50M from below GL (ii) Size of tank upto water level shall be measured

Temporarily blocking of sewage line with suitable wooden plugs/gunny bags and cleaning the same by rod-ding and removing the sludge alongwith brick bats/stones/broken bottles/any other foreign materials etc complete and cleaning the sewage line with water by mechanilly as directed by EIC, and taking out the blocking arrangements of inlet and making the system functional for 150 mm bore size of pipe lines, complete all as specified and directed.

All as per item No 158 above but 200 mm bore

All as per item No 158 above but 250 mm bore

Excavating in trenches, n exc 1.5m wide and n exc 1.5 m depth; for foundation, etc. or for shafts, wells, cesspits, manholes,pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out as in soft/loose soil, complete all as specified and directed.

Demolition and breaking up 150 mm dia bore sewage / drain pipe / RCC hume pipe including PCC packing under haunching against the sides of pipe bed and complete PCC of bed all specified and directed.

M&L for 150 mm bore SGSW drain pipe (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as specified and directed.

M&L for PCC 1:3:6, type C2 using 40mm graded stone aggregate as in bed to drain pipes of 150 mm bore dia including packing uner , and haunching against the sides of pipes after they are laid and tested in, complete all as specified and directed.

Returning, filling in, including spreading, levelling , watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed.

M&L preparation of old painted surface of walls and applying one coat exterior emulsion weather coat paint of Apex (Asian Paint) / Weather coat (Berger) / Excel Top Guard (Nerolac) complete all as specified and directed.

Complete removal of existing treatment on wall / roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour complete all as specified and directed. (Note :-Rate included for necessary scafolding and arrangement for working up to 15 mtrs height).

M&L for Providing and applying minimum 1mm thick wall care putty over prepared surface to achive the surface even and smooth for painting complete all as specified and directed. (Note :- Rate included for necessary scafolding and arrangement for working up to 15 mtrs height).

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. Note- (i) Primer and emmulsion to be carried out through air less spray machin ( Mechanical means). (ii) Rate included for necessary scafolding and arrangement for working up to 15 mtrs height.

Removal of excavated materials exc. 1.50 Km but n. exc. 5 Km and deposited where complete all as specified and directed.

M/S SWATI CONSTRUCTION

M/S Reliance Construction