REPAIR TO LEAKAGE SEEPAGE OF BATH TOILET SUNKEN PORTION ROOFS AND POST ATT TO CERTAIN BUILDINGS IN DOMESTIC AREA AT AFS BHISIANA

Amount

Demolition of Cement Concrete (un-reinforced) in Toilet Floors, Sunken Floors including taking out PCC of any description and removing debris, etc. to Outside of MD/AF Land, complete all as specified and as directed by Engineer in Charge.

M&L Screed Bed 15mm thick in Cement Mortar 1:4 on Sunken Portion or on Concrete Surfaces, mixing liquid WPC as per manufacturers instructions by Weight of water proofing compound 3% of cement, Plastered Surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed by Engineer in Charge. NOTE: WPC will be Measured and Paid under appropriate Item.

Supply only Integral Water Proofing Compound, ISI Marked, as approved, complete all as specified and as directed by Engineer in Charge.

M&L applying evenly Two Coats of Hot Blown type Bitumen at the Rate of 1.50 Kg per Square Metre on Concrete Surfaces, complete all as specified and as directed by Engineer in Charge.

M&L Cement Concrete 1:5:10 (40mm graded stone aggregate) as filling in Sunken Floors, Mass Concrete, etc., complete all as specified and as directed by Engineer in Charge.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 25mm thick as in Flooring, finishing Cement Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed by Engineer in Charge.

M&L for 50mm dia GI spout pipe fixed in sunken floors by means of cutting holes in wall bedded in cement mortar and making good the disturbed portion of wal, complete all as specified and as directed by Engineer in Charge. NOTE : Cement Concrete will be Measured and Paid for separately under appropriate Item.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and as directed by Engineer in Charge.

M&L for 15 mm thick plaster in 1:4 cement mortar and finishing the surface even and fair without using extra cement including applying two coat of cement base paint over and a coat of primer after preparation of new plastered surfaces, complete all as specified and as directed by Engineer in Charge.

M&L Rough Cast Plaster on Brick Walls consisting Under Coat of Cement and Sand Mortar 1:3 not less than 10mm thick and while it is still in Plastic state the Rough Cast Mixture consisting of Crushed Stone or Fine Gravel mixed with Coarse Sand and Cement in the Ratio 1:1:1 shall be applied and finish Even and applying two coat of cement base over a coat of primer, complete all as specified and as directed by Engineer in Charge.

M&L for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and fair (without using extra cement) etc including applying two coats oil bound distemper (OBD) over a coat of primer and after preparation of plastered surfaces complete all as specified and directed.

M&L for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and fair (without using extra cement) etc including applying three coats white wash and after preparation of plastered surfaces complete all as specified and directed by Engineer in Charge.

M&L for 5 mm thick cement plaster 1:3 on fair faces of brick work or concrete surfaces in ceiling and finishing the surface even and fair (without using extra cement) etc including applying three coats of white wash and after preparation of plastered surfaces complete all as specified and directed by Engineer in Charge.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed by Engineer in Charge.

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in Flooring, set and jointed in Neat Cement Slurry and pointed in White/Coloured Cement, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed by Engineer in Charge. NOTE : Cost of Screed Bed will deem to be included in the Quoted Unit Rate.

M&L Coloured Glazed Ceramic Tiles 350x250x7 mm/ 450x300x7mm thick in Vertical Surface i.e. Dado, Skirting,etc., set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles, laid over and including 10mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed by Engineer in Charge. NOTE : Cost of rendering will deem to be included in the Quoted Unit Rate.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in Flooring, set and jointed in Neat Cement Slurry and pointed in White/Coloured Cement, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed by Engineer in Charge. NOTE : Cost of Screed Bed will deem to be included in the Quoted Unit Rate.

M&L for Coloured Ceramic/ Printed tiles 7 to 8mm thick (square/rectangular) on vertical surfaces as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in CM 1:3 to receive vertical tiles complete all as specified. NOTE : Cost of rendering will deem to be included in the Quoted Unit Rate.

M&L for Non Skid Vitirified Coloured Ceramic Tiles 10mm thick (Square/Rectangular), Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc. set and jointed in Neat Cement Slurry and pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed by Engineer in Charge. NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.

M&L for Non Skid Vitirified Coloured Ceramic Tiles 10mm thick (Square/Rectangular),Light shade, Polished, area of each Tile exceeding 0.18 Square Meter but not exc. 0.36 Square Metre in Vertical Surface i.e. Dado, Skirting,etc., set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles, laid over and including 10mm thick rendering in Cement Mortar 1:4, complete all as specified and as directed by Engineer in Charge. NOTE : Cost of rendering shall deem to be include in the Quoted Unit Rate.

Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed by Engineer in Charge.

M&L Machine Cut Kota Stone Slab 20-25mm thick in Flooring over and including Cement Screed 15mm thick in Cement Mortar 1:6, laid and jointed with Grey Cement Slurry mixed with Pigment to match the Shade of the Slab including Rubbing and Polishing, complete all as specified and as directed by Engineer in Charge. NOTE : Cost of Screed Bed will deem to be included in the Quoted Unit Rate.

M&L Machine Cut Kota Stone Slab 20-25mm thick in Riser of Steps, Skirting, Dado and Pillar, laid over and including Cement Screed 10mm thick in Cement Mortar 1:4, laid and jointed with Grey Cement Slurry mixed with Pigment to match the Shade of the Slab including Rubbing and Polishing, complete all as specified and as directed by Engineer in Charge. NOTE : Cost of Rendering will deem to be included in the Quoted Unit Rate.

M&L for 12-15mm thick green marble slab flooring including 15mm thick screed bed in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab one side bullnosed etc complete all as specified and as directed by Engineer in Charge. NOTE : Cost of Screed Bed will deem to be included in the Quoted Unit Rate.

M&L for 12-15mm thick green marble including 10mm thick cement plaster in CM 1:3 in riser of steps, skirting , dado and pillar with one side bullnosed and jointed with grey cement slurry mixed with pigment to match the shade of the slab etc complete all as specified and as directed by Engineer in Charge. NOTE : Cost of Rendering will deem to be included in the Quoted Unit Rate.

Taking up or down Steel Tubing 15mm bore (dia) with Fittings/ Connections, complete all as specified and as directed by Engineer in Charge.

Re-Fixing Steel Tubing 15mm bore (dia) and Fittings in new or old position, (Serviceable Pipes and Fittings obtained from Item here-in-before) after cleaning inner and outer surfaces of Pipes by using of Wire Brush including provision of new GI Fittings (as required), complete all as specified and as directed by Engineer in Charge.

M&L Galvanised Tubes 15mm bore (dia), 'medium grade', with all Fitting and fixed complete to Walls and Ceilings or laid in Floors, complete all as specified and as directed by Engineer in Charge.

Taking up or down Steel Tubing 20mm bore (dia) with Fittings/ Connections, complete all as specified and as directed by Engineer in Charge.

Re-Fixing Steel Tubing 20mm bore (dia) and Fittings in new or old position, (Serviceable Pipes and Fittings obtained from Item here-in-before) after cleaning inner and outer surfaces of Pipes by using of Wire Brush including provision of new GI Fittings (as required), complete all as specified and as directed by Engineer in Charge.

M&L Galvanised Tubes 20mm bore (dia), 'medium grade', with all Fitting and fixed complete to Walls and Ceilings or laid in Floors, complete all as specified and as directed by Engineer in Charge.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall, complete all as specified and directed by Engineer in Charge.

Dismantling/lowering down Rotational Moulded Polyethylene Water Storage Tank of Capacity exc. 250 Litre but not exc. 500 Litre from Roofs after disconnecting Water Pipe Lines, omplete all as specified and directed by Engineer in Charge.

S&F for Rotational moulded polyethylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top) Three layers, hoisted and fixed in position omplete all as specified and directed by Engineer in Charge.

Dismantling/lowering down Rotational Moulded Polyethylene Water Storage Tank of Capacity exc. 500 Litre but not exc. 1000 Litre from Roofs after disconnecting Water Pipe Lines, complete all as specified and as directed by Engineer in Charge.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity (Cylindrical, Vertical with Closed Top), hoisted and fixed in Position all as specified in MES Schedule, complete all as specified and as directed by Engineer in Charge.

S&F Ball Valve 20mm dia (minimum Weight 210 Gram), high pressure of PTMT with Epoxy coated Aluminium Rod and High density Plastic Ball, screwed for Iron Pipe, complete all as specified and as directed by Engineer in Charge.

S&F in repairs Ball Valve 20mm dia (minimum Weight 210 Gram), high pressure of PTMT with Epoxy coated Aluminium Rod and High density Plastic Ball, screwed for Iron Pipe, complete all as specified and as directed by Engineer in Charge.

S&F in repairss Gun Metal Gate Valve 20mm bore (dia) with Iron Wheel Head including Flange, screwed both Ends for Iron Pipe, complete all as specified and as directed by Engineer in Charge.

S&F as repairss 100 mm bore Traps 'P' or 'S' complete all as specified and directed by Engineer in Charge.

S&F in repairs Vitreous China White Squatting Pan of size 580x440mm, 'Orissa' Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces , complete all as specified and as directed by Engineer in Charge. Note: "P" or "S" Traps shall be measured and paid seperately

S&F in repairs Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with Trap including seat cover and Fixing Bolts and Making Good to Floor/ disturbed surfaces, complete all as specified and as directed by Engineer in Charge.

S&F in repairs 75mm dia PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) and Making Good to Floor/ disturbed surfaces, complete all as specified and as directed by Engineer in Charge.

S&F in repairs Flush pipe of polyethylene of low or high density of PVC, 32 mm dia and make a proper connection with water closet and low level cistern with leak proof , complete all as specified and as directed by Engineer in Charge.

S&F in repairs PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 , complete all as specified and as directed by Engineer in Charge.

S&F in repairs Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back) with Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 , complete all as specified and as directed by Engineer in Charge.

S&F in repairs Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe , complete all as specified and as directed by Engineer in Charge.

S&F in repairs 15 mm bore Stop Valve chromium plated with long shank and cup (concealed type) ,cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union , complete all as specified and as directed by Engineer in Charge.

S&F in repairs Angle Valve 15mm bore (dia), Cast Copper Alloy, Chromium Plated, screwed down, high pressure, screwed both Ends for Iron Pipe with Wall Flange , complete all as specified and as directed by Engineer in Charge.

S&F in repairs PVC Connection Pipe 15mm size and 45 Cm in length with Adopter Nuts of PVC , complete all as specified and as directed by Engineer in Charge.

S&F in repairs Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (one Pair) ,complete all as specified and as directed by Engineer in Charge.

S&F in repairs Bib Tap 15mm bore (dia), Cast Copper alloy, Fancy type with Flange Chromium Plated, screwed for Iron Pipe or for Brass Ferrule and Chromium Plated Wall Flange, complete all as specified and as directed by Engineer in Charge.

S&F in repairs Shower Rose 125mm in size, Brass Chromium Plated, Fancy type with Swivel Joints including Flange and suitable for fixing Steel Pipe 15mm bore (dia) or Union , complete all as specified and as directed by Engineer in Charge.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or labo-ratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brack-ets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer in Charge.

Demolition Cement Concrete (un-reinforced) of any description and any position including removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed by Engineer in Charge.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick as in Plinth Protection, finishing Cement Concrete surface Even and Smooth without using Extra Cement, complete all as specified and as directed by Engineer in Charge.

Demolition Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed by Engineer in Charge.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed by Engineer in Charge.

M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in 1:4 cement mortar complete all as specified and as directed by Engineer in Charge.

M&L for Removing of bushes upto 10 cm dia trunk, grass from roof top, racking out joints/pointing to brick tiles laid flat and flush pointing with 1:3 cement mortar compound, all as specified as directed.

S&F in repairs PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints fixed to Walls/ floor, complete all as specified and as directed by Engineer in Charge.

S&F in repairs PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints fixed to Walls/ floor, complete all as specified and as directed by Engineer in Charge.

S&F in repairs PVC (SWR) 110mm bore (dia), Bend any type, provided with Access Door, etc. and jointing with Solvent Cement , complete all as specified and as directed by Engineer in Charge.

S&F in repairs PVC (SWR) 75mm bore (dia), Bend any type, provided with Access Door, etc. and jointing with Solvent Cement , complete all as specified and as directed by Engineer in Charge.

S&F 75mm bore( Sand Cast ) Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls/floor but as in repairss complete all as specified and directed.

S&F 100 mm bore (Sand Cast ) Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls but fixed as in repairss complete all as specified and directed.

S&F 75 mm bore CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access door as in repairss complete all as specified and directed.

S&F 100mm bore CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access door as in repairss complete all as specified and directed by Engineer in Charge.

S&F 75 mm dia CI bends (any radius), diminishing pieces or tapers provided with access door in repairs complete all as specified and directed by Engineer in Charge.

S&F 100 mm dia CI bends (any radius), diminishing pieces or tapers provided with access door in repairs complete all as specified and directed by Engineer in Charge.

M&L for Providing, cement concrete type B1 1:2:4 (20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, roof padding complete all as specified and directed

Dismantling wall & ceiling board any type, any thickness including cover fillets complete all as specified & directed by Engineer in Charge.

M&L for Non asbestos fibre cement boards 600x600x4mm thick fixed in ceiling Aluminium frame work with screws complete all as specfied.

S&F Anodised aluminium snap grid frame work 605x605 mm for false ceiling complete all as specfied by Engineer in Charge.

M&L for Shutters of any description exc 1 sq. m, but not exc 2 Sqm each taking down and refix in same opening after easing and cutting in required length and width with necessary screwing and naling if required. all as specified as directed.

Taking down Chowkhats or frames with shutter not exc 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed by Engineer in Charge.

S&F Solid PVC Door Frame of size 50x47 mm made out of 5.0mm having Wood Grain Printed PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening, complete all as specified and as directed by Engineer in Charge.

Supply & fitted to Factory Made Solid Panel PVC Door Shutter 30mm thick (Stile) Plain colour (Ivory shade) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded wood grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and Wood Grain PVC Sheets for Top Rail, Lock Rail & Bottom Rail on either Side and as gap insert for Top Rail & Bottom Rail, Panelling of Wood grain PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable 5mm thick x 15mm wide PVC Sheet Beading used inside Stiles and Rails and decorative PVC Beading of 10mm x 10mm (90°) and jointed together with Solvent Cement and fixing in the Frame and hanging/fixing with Stainless Steel Hinges, complete all as specified and as directed by Engineer in Charge. NOTE : Stainless Steel Hinges will be Measured and Paid under appropriate Item.

S&F Butt hinges 100mm size extruded aluminium alloy with galvanised mild steel hinges pin anodised and fixed complete all as specified and directed by Engineer in Charge.

S&F Aluminium handle 100mm long (weight not less than 120 Gram), cast type anodised complete all as specified and directed by Engineer in Charge.

S&F Aluminium Barrel Tower Bolt 150mm long (weight not less than 180 Gram), Extruded Section, complete all as specified and as directed by Engineer in Charge.

Material and labour for laying 50 micron polythelene film, black in floors of sunkan, complete all as specified and directed by Engineer in Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed by Engineer in Charge.

S&F for Rolled mild steel in Rolled sections as in main and cross beams, hip and jack rafters: purlins where connected to common rafters and running rails and guides for sliding doors: fixed with angle cleats or other connecting plate complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer exposed to view surfaces complete all as specified and as directed by Engineer in Charge.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by Engineer in Charge.

S&F for Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer in Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer in Charge.

S&F in repairs Brass Spindle for Bib tap, Pillar tap, Stop tap, angle cock, Wall mixture and Basin Mixture etc of any description, complete all as specified and directed by Engineer in charge.

Dismantling brick tiles or terracing tiles single layers on roof complete all as specified and directed by Engineer in Charge.

Demolition of mud in roofs, any thickness including plastering/pcc padding and leaping (where full thickness removed or only a part thereof) complete all as specified and directed by Engineer in Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc including dismantling existing membrane complete all as specified and directed by Engineer in Charge.

Brushing neat cement slurry with 3.0 kg of cement per sqm complete all as specified and directed by Engineer in Charge.

M&l for providing cement concrete type B1 (1:2:4) 20 mm graded stone aggregate for providing slope, roof kerbs or mud stops rounded or chamfered edgescomplete all as specified and directed by Engineer in Charge.

M&L for 10mm thick Screed bed or bedding layer in cement mortar 1:4, laid on roof, mixed with water proofing compound when concrete is green, as per manufacturere instructions complete all as specified. (Note - Water proofing compound shall be measured and paid separately).

M&L for APP based polymeric membrane of minimum 3 mm thick and minimum weight not less than 3.0 Kg/sqm, reinforced with polyster non woven fabric matt (weight not less than 150 gm/sqm), laid with forced application over roof surface with a coat of hot blown bitumen conforming to IS-3384-1965 of grade 85/25 @ 1.2 kg/Sqm at bottom of the membrane as bonding material, including one coat of aluminium paint complete all as per manufacturer's instructions all as specified and directed by Engineer-in-Charge.

M&L for UV stable single component fibre reinforced elastomeric liquid applied waterproofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in three coats. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must. (Make: Asian paints or equivalents). Note: The work shall be executed by the authorized applicator of the manufacturer only.

M&L for racking out joints/pointing to brick tiles and flush pointing with 1:3 cement mortar with water proofing compound, complete all as specified and directed by Engineer in Charge.

S&F Roof trusses (framed), Trussed, Purlins, Crane Gantries, Rails and Fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed by Engineer in charge Fe 410-W(Gde-E- 250), Complete all as specified and as directed by Engineer in Charge.

Disconnecting existing tanks Exc 250 Ltr and not exc 500 Ltr, setting aside (for lowering if required) for repairs, cleaning, etc and hoisting if required reconnecting and re fixing in position after and including cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc, complete all as directed by Engineer in Charge.

Disconnecting existing tanks Exc 500 Ltr and not exc 1000 Ltr, setting aside (for lowering if required) for repairs, cleaning, etc and hoisting if required reconnecting and re fixing in position after and including cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc, complete all as directed by Engineer in Charge.

M&L for 15 mm thick plaster in 1:4 cement mortar and finishing the surface even and fair without using extra cement including applying two coat of Premium Acrylic Emulsion Exterior Paint over and a coat of primer after preparation of new plastered surfaces, complete all as specified and as directed by Engineer in Charge.

Taking up or down Steel Tubing 25mm bore (dia) with Fittings/ Connections, complete all as specified and as directed by Engineer in Charge.

Re-Fixing Steel Tubing 25mm bore (dia) and Fittings in new or old position, (Serviceable Pipes and Fittings obtained from Item here-in-before) after cleaning inner and outer surfaces of Pipes by using of Wire Brush including provision of new GI Fittings (as required), complete all as specified and as directed by Engineer in Charge.

M&L Galvanised Tubes 25mm bore (dia), 'medium grade', with all Fitting and fixed complete to Walls and Ceilings or laid in Floors, complete all as specified and as directed by Engineer in Charge.

M&L for post constructional anti termite treatment along the external and internal wall below concrete or masonry apron or below tiles using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed by Engr-in-Charge

M&L for post constructional anti termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cementmortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed by Engr-in-Charge

M&L for post constructional anti termite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed by Engr-in-Charge

yogesh kumar contractor (BID ID -3111718)

REYANSH GARG AND COMPANY (BID ID -3109849)

GUPTA AND ENGINEERS (BID ID -3110142)

M/s Luxmi Constructions (BID ID -3105427)

STELLAR PROJECTS (BID ID -3111615)

Aman Enterprises (BID ID -3104147)

Rasvinderpalandco (BID ID -3106110)

M/s BALDEV SINGH (BID ID -3109748)