SPECIAL REPAIR TO TYPE III ACCOMODATION BLDG NO. 33, 36 and 38 AT ADM AREA CPE ITARSI UNDER GE (I) (P) FYS JABALPUR

Amount

Demolition of Cement concrete (unrein forced) in ground floor and pavings not exc 15 cm tickness (below or above ground level) including removing of debrish from site complete all as specified and directed

Excavating over areas,under floor n exc 1.5m deep and getting out any Type of Soil below floor complete all as specified and directed

M&L 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in Sub base and plinth protection finish the cement concrete surfaces fair and even laid in bays complete all as spciified and directed

M&L for 25mm thick PCC (1:2:4) type BO (using 12.5mm graded stone aggregate) as in sub floor to receive floor finishes complete all as specified and directed.

M&L for Moorum and sand filling under floors or pavings laid in layers n exc 15 cm thick spread, levelled and rammed including watering (Sand and moorun will be mixed in ratio (1:1) in filled under floor) complete all as specified and directed.

Removing excavated material n exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L plain cement concrete cast in situ (1:3:6) type C1 using 20 mm graded stone aggregate as in copings ,hold fast,back filling of pressed steel frame and other similar work water troughs and the like including weathering, slightly rounded or chamfered angles and throating etc including form work and fair finishing the concrate surface all as spcefied and directed

Taking down cement or cement lime plaster on brick walls etc including raking out joints, hacking for key scrubing down with water etc including removing complete all as specified and directed .

M&L for vendering 15 mm thick on internal surfaces of wall in CM 1:6 including finished surfaces even and somooth without using extra cement all as spcefied and directed

M&L for cutting "V" section to cracks in existig roof or terracing/brick wall including cleaning, and grouting with cement sand slurry (1:3) complete all as specified and directed.

M&L for 15 mm thick cement plaster externally in CM (1:4) be with cement mortor mixed with :WPC as per manufacturer instructions with cement ) and finished fair and even complete. (Note :- WPC shall be measured & paid separately) including dubbing coat if required on ground directed (No extra payement will be paid for dubing coat) complete all as specified and directed.

M&L for 10 mm thick cement plaster in CM (1:3) on celing of concrete surfaces and finished the surface even and smooth complete all as specified and directed.

Supply only water proofing compound complete all as specified and directed.

M&L for applying three coat of white wash including preparation of new plaster surface on ceiling complete all as specified and directed.

M&L for two coat oil bound distemper over a coat of primer on new plastered surface including prepration of surface complete all as specified and directed.

M&L for two coat Cement based paint over a coat of primer on new plastered surface including prepration of surface complete all as specified and directed.

M&L for two coats of oil bound distemper on old surface including complete removal , washing, rubbing down and stopping of existing treatment over a coat of JK Birla wall care putty and making the surface even and smooth and filling the uneven and small holes and making the edges of plaster properly by plaster of paris complete all as specified and directed.

M&L for two coats of cement based paint on old plastered surface including complete removal of existing tratment washing down and rubbing and prepration of surface complete all as specified and directed.

M&L prepration of old decorated plastered or un plastered surface including cornices etc and applying two coat of white wash on ceiling complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc 1.5 Sgm each and making good of disturbed surface match the existing surface complete all as specified and directed.

-ditto - but exc 1.5 Sgm but not exc 4 Sgm each complete all as specified and directed.

S&F 125x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates,hinges,hold fast(40x3mm) etc. complete size /profile of frame as per IS complete all as specified and directed.

S&F 105x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates,hinges,hold fast(40x3mm) etc. complete size /profile of frame as per IS complete all as specified and directed.

S&F 30mm thick flush shutters, (Factory made) soild core construction,with black board core and plywood face panels and one face is covered with decorative face veneer with lipping / frame to match complete all as specified and as directed.

S&F 35 mm thick 2nd Class hard wood (Factory made) glazed and skeleton shutters , open rebeted and prepared to receive glass, gauze etc (without sash bars ), edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc , sizes of members of shutters as specified in SSR part-I section 8, clause 8.24 (a) complete all as specified and directed.

S&F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube.fixing as per specification and drawing complete all as specified and directed.

S&F 30mm thick PVC (factory made) panelled door shutter as per IS- 4020 made from MS tube of top and bottom rods. MS frame shall be covered with heat maulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on plain side & as gap insert for top and bottom rail. Pannelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawings complete all as specified and directed.

S&F Framed work as in doors or gates of angle or any type of grill other section with gusset plate rails, braces, etc complete drilled for fixing of steel sheeting or other covering doors etc prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittngs and hanging also fastening and fixing complete of Fe-290 (Gde E-165) all as specified and directed.

M& L for Box type steel window double (glazed & gauged) emade of ERW tube P- section of size 60 mm x 25 mm double rebated outer frame comprise glazed skelton shutter door frame of ERW tube P-section size 50 mm x 20 mm with two Nos openable leaf cnsisting of two Nos of sash bar of T-sec 20 mm x 3 mm welded to frame with one No vertcale mullion of ERW of ERW box type T-section size of 60 mm x25 mm FI 2 mm thick welded / screwed to frame for fixing of wire guage/glass including fixture and fitting like as handle, tower bolt stopper , cleat, pintal hinges, holdfast primer etc, complete all as specified and directed.( Window will be measured single side only) NOTE : The unit rate quoted is inclussive of following :- (i). One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrte surface (ii) 4 nos MS steel lugs made of 20X5 mm Iron flat 200 mm long (iii) PCC block for embedding lugs

S&F 100mm size MS butt hinges medium wt cold rolled complete all as specified and directed.

S&F 150mm long aluminium handles cast type, anodised, complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of etruded section and fixed complete all as specified and directed.

S&F in Aluminium sliding door bolts 300mm long plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bold plate and two on staple plate and fixed complete all as specified and directed.

S&F of 300mm long mild steel ordinary rat tail rod pattern springs including roller & roller plate complete all as specified and directed.

S&F100mm long hasp and staple,mild steel,wire type, stove enamelled black,including bolt to hinges plate and fixed with screws complete all as specified and directed.

S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed.

S&F of wire netting as chicken wire mesh of galvanised steel wire 0.71mm dia and size of mesh 25mm for cracks fixed with nails etc complete all as specified and directed.

M&L for mild steel wire cloth 0.36mm nominal dia of wire & avg width of aprature 1.40mm & fixed with stinless steel wire staple complete all as specified and directed.

M&L for prepration of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for prepration of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide on new steel surfaces of any description over 10cm width or girth complete all as specified and directed.

Demolition of any type of floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non skid coloured ceramic edge cut tiles 7-8mm thick (square/rectangular) area of each tile not exceeding 0.11sqm as in floors set & jointed in neat cement slurry & pointed in white or coloured cement to match the tiles over including screed bed 15mm thick in cement mortar (1:4) for laying floor finished complete all as specified and directed.

M&L for non skid coloured ceramic edge cut tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but n.exceeding 0.18sqm as in floors set & jointed in neat cement slurry & pointed in white or coloured cement to match the tiles over including screed bed 15mm thick in cement mortar (1:4) for laying floor finished complete complete all as specified and directed.

M&L for glazed ceramic coloured edge cut tiles 450x300x7mm thick on vertical surfaces such as skirting dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in CM (1:4). Complete all as specified & directed

M&L 20-25 mm thick cuddapa prepolished stone over and including 10 mm thick cement mortar (1:4) bedding laid & jointed with slurry cement mixed with pigment to match the shade of the slab including rubbing and polishing,rounding to edge of stone slab one edge,such as steps,cooking plateorm and similar situtions complete all as specified and directed. (Note-Hole in stone slab for accomodate the gas pipe where required complete including taking out old stone slab all as specified & directed.

S&F PVC water storage tank of 500 ltr capacity anti bactrial, tripple layer manufactured ISI marked with rotated lid including S&F 20mm dia PVC float valve assembly including dismantling of existing PVC water tank of any capacity complete all as specified and directed.

S&F in repair Gun metal, globe or gate valves for 15 mm dia bore pipe with iron wheel head, screwed both ends for iron pipe and fixed in repair etc complete all as specified and directed.

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F 15 mm GI nipple suitable for HDPE water tanks including necessary driling holes etc fixed complete all as specified and directed.

S&F sinks in repair without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plug washers and waste pipe including fixing contilever bracket and connecting union to pipe over all size 495 mmx 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair pillar taps 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipes complete all as specified and directed.

Taking down GI tubing 15mm bore of any description including cleaning for refixing complete all as specified and directed.

Taking down GI tubing 20mm bore of any description including cleaning for refixing complete all as specified and directed.

M&L GI tubing 15 mm dia medium grade galvanized, with all fittings fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L GI tubing 20mm bore medium grade galvanized, with all fittings fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for Refixing old GI pipe 15 mm bore & connections in new or old position to walls and ceiling or laid in floor complete all as specified and directed.

M&L for Refixing old GI pipe 20 mm bore & connections in new or old position to walls and ceiling or laid in floor complete all as specified and directed.

S&F in repair 15mm bore bib tap chromium plated fency type. cast copper alloy with crutch or butterfly handle ,screwed down ,screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15mm bore angle valve /stop valve chromium plated fency type.cast copper alloy screwed down high pressure,crutch or butterfly handle, ,screwed both end for pipe or for unions complete.chromium plated with suitable type as complete all as specified and directed.

Supply and fixed in repair stop valves, 15mm dia, cast copper alloy,CP fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S&Fin repair PVC low level 10 litre capacity valveless syphonic action type white flushing cistern with inlet ball valve float and handle including brackets and necessary fittings etc fixed in repairs complete all as specified and directed.

S&F in repair viteress china squtting pan "ORISSA PATTERN" size 580x440mm white with integral foot rest and flush pipe complete including provision of concrete bedding (1:2:4) type B-0 complete all as specified and directed.

S&F in repair WHB white size 550x400mm vitreous china(flat back or angle back type) any size,including cutting for and pinning end of bracket or eracting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F (in repair) towel rail 600mm long of PTMT fixed with and including chromium plated brass screw and wooden/plastic cleats.(minimum weight 190grms) complete all as specified and directed.

S&F PVC connection 15mm bore size with PTMT nuts of length 450mm long complete all as specified and directed.

S&F 32 / 40mm dia PVC pipe low density (LDPE) of pressure 6kg/CM2 fixed to wall or laid in floor as waste pipe complete all as specified and directed.

S&F 100mm dia size CP shower rose fancy type with or without joint including fixing to steel pipe or union complete all as specified.shower arm 195mm long complete all as specified and directed.

S&F 75 mm out let PVC floor trap with chromium plated grating including Jointing to waste pipe and fixed in cement concrete B1 (1:2:4 ) using 20 mm graded stone aggregate complete all as specified and directed.

Demolition and breaking up or down PVC /AC/CI /Cement rain pipe fixed in any position complete all as specified and directed.

S&F 110mm dia PVC(SWR) pipes single soketed in any length with rubber ring jointed fixed to wall complete all as specified and directed.

S&F 75mm dia PVC(SWR) pipes single soketed in any length with rubber ring jointed fixed to wall complete all as specified and directed.

S&F PVC (SWR) bends 110 mm dia provided with access door complete all as specified and directed.

S&F PVC (SWR) bends 110 mm dia complete all as specified and directed.

S&F PVC (SWR) bends 75 mm dia complete all as specified and directed.

S&F PVC (SWR) bends 75 mm dia provided with access door complete all as specified and directed.

S&F PVC (SWR) cowl 110 mm dia complete all as specified and directed.

Demolition of reinforced cement concrete in floors, beams, chajjas, chimney, landing slab in any position orany height and similar suspended works complete all as specified and directed.

M&L RCC (1:2:4) type B1 (using 20 mm graded stone aggrigate)as in slab, etc complete all as specified and directed.

M&L for Form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work n.exc 200mm thick horizontal or sloping complete all as specified and directed.

S&F of MS 10mm dia and over TMT bar, cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire(annealed not less than 0.9mm dia) including welding,rivetting etc complete all as specified and directed.

Demolition brick work or stone / boulder masonry built in cement mortar as in wall etc complete all as specified and directed.

M&L for brick work with sub class 'B' brick modular size in CM (1:4)straight or curved on plan exc 6m mean radius as in wall etc complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including necessary forms mould mitred /stopped ends etc complete all as specified and directed.

M&L PCC (1:3:6) type C2 in using 40mm graded stone aggregate Surface channel or drains including necessary form works, stops, moulds etc complete all as specified and directed.

S&F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in chajja roof covering/cladding to wall, fixed with self tapping screws suitable screw complete all as specified and directed

S&F of MS Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe 290 Gde E - 165 complete all as specified and directed.

M&L chequered cement concrete tiles 20 cm x 20cm x 20 mm thick set jointed with grey cement pigment and pointed in neat cement slurry fixed door 20 mm thick screed bed in CM(1:6) in floors complete all as specified and directed.

S&F 18 MM thick prelaminated MDF Board exterior grade fixed to timber/steel frame work with screwsas in cubboard shutter colour and design as approved Make Panelmax of Green Ply, Greenply, Novapan, Bhutan board complete all as specified and directed.

S & F Continuous (piano) hinges mild steel bright finish or electro galvanised width of open flaps 30mm complete all as specified and directed.

M&L pressed steel frames for cup board chokhat of size 60x40mm with one or more rebates incl necessary fixing lug, hold fasts etc and one coat of redoxide primer complete all as specified and directed.

S&F 40mm thick precast cement concrete louvres and jallies,Type C0 PCC (1:3:6) (using 12.5mm stone graded aggregate)(measured solid),(Set in Cement Mortar 1:4) ( including all mouldings , framing etc complete all as specified and directed.

M&L for Cutting holes in brick wall,concrete walls built in cement mortar or cement lime mortar for inserting hold fasts and making good dismelted portion in cement mortor (1:3) or cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as required.Area exc half brick but n.exc one brick complete all as specified and directed.

Taking down/removing the existing roof treatment including backing and dispose off exc 100m as directed complete all as specified and directed

Taking down/removing the existing roof treatment including backing coat if any and disposal of debris to a distance not exc. 100m as directed by Engr-in-Charge and brushing neat cement slurry with 3.0 Kg/Sqm over roof slab and priming the surface of plaster using bitumen primer @ 0.4 Ltr/Sqm and applying water proofing treatment using 3mm thick Acetic poly propylene (APP) Membrane modified pre fabricated with non woven polyester reinforced established Weight not less than 3.6 kg /sqm laid over a coat of bitumen 85/25 @ 1.2 Kg/ Sqm as per manufactures instructions complete all as specified and directed.

M&L for 15 mm thick cement screed bed in CM (1:4) on roof surfaces and incl benching and coving or concrete surfaces mixed with WPC @ 03% by weight of cement and finished the surface even and smooth with out using extra cement complete. (Note :- WPC shall be measured & paid separately)

M&L for Cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished with grey cement and no pigment complete all as specified and directed

E/M Portion :- Excavation in trenches in any type of soil n. exc 1.5 mwide and n. exc 1.5 m in depth and getting out for foundation of pole, laying under ground cables etc and getting out complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm in soil complete all as specified and directed.

Material and labour for river washed and screened dry sand for filling in trenches below and around the cable for cushioning including punning down as specified in relevant clause of SSR Part I complete all as specified and directed. Note: Punned thickness shall only be measured and paid.

Material and labour for well burnt brick sub class 'B' old size bricks laying in trenches perpendicular to axis of the cable complete all as specified and directed.

Material and labour for GI tubing light grade, 50mm dia with all necessary fittings, laid in trenches, under floor/road crossing, fixed on poles for cable protection fixed with the clamps made out of FI 25 x 3mm duly painted with two coats of aluminium paint over a coat of approved primer etc. complete all as specified and directed.

Supply, lay, connecting and testing cable of size 25 Sqmm. 4core, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty), 1100 volts grade with earthed system, stranded aluminium conductor including making input and output connections with using suitable size of thimbles and glands including taking down unserviceable UG cable all as specified and directed.

Taking down carefully aluminium / copper point wiring with surface/ concealed PVC conduit or wooden batten ( light, fan, socket, bell or power ) including sunk in cast iron / pressed steel terminal boxes except fitting such as switches, ceiling roses, lamp holders, sockets, regulators, call bell, light fitting any sketch etc and making good disturbed surfaces of walls, floors etc complete all as specified and directed.

M & L for Point wiring with PVC insulated 1.5 Sq mm multi stranded copper conductor cable 1100 Volts grade drawn into and including concealed PVC Conduit medium grade not less than 19/20 mm ( ISI marked ) with all fitting and fixing accessories including sunk in cast iron / pressed steel terminal boxes ( duly painted with two coats of anti corrosive paint outside and two coats of aluminium paint inside ) with 2.8 mm thick hylum brand laminated white bakelite sheet cover for mounting switches, sockets, fan regulators etc and 1.0 Sq mm multi stranded copper conductor cable as continuous earth wire complete including taking down unserviceable one for the following :- (a) One light point/fan pont controlled by one switch

(b) One socket outlet 5 Amps controlled by one switch on the same board.

(c) One socket outlet 5 Amps controlled by one switch on independent board.

(d) One bell / buzzer controlled by one bell push.

(e) One light point controlled by two way switch.

All as per item No. 106 above but with 4.0 sq mm multi stranded copper conductor cable for one 15 Amps socket outlet controlled by one switch on independent board and 2.5 sq mm PVC insulated multisranded copper conductor cable as continuous earth wire complete all as specified and directed.

Material and labour in repairs for sub main wiring with two single core 6 sqmm multi stranded copper conductor, FRLS PVC insulated, unsheathed cable including rigid non metallic PVC conduit medium grade, ISI marked, 25 mm dia for sub main wiring including 6 sqmm FRLS PVC insulated and unsheathed stranded copper conductor as earth wire in conceled in wall of make & maching the existing surface make & maching the existing surface and making good to the disturbed surfaces to match the existing surfaces complete all as specified and directed. Note :- Two runs of 6 sqmm copper conductor cable, one run of 6 sqmm copper conductor and one run of PVC conduit will be measured as one unit length.

S&F Modular switch 1 way 6A, 240 Volts 1 module complete including taking down unserviceable one all as specified and directed.

S & F Modular Switch piano flush type 5 Amps single pole two way complete.

S & F Modular Socket 6A/16A - 2/3 pin combined 2 module 230 Volts complete including taking down unserviceable one all as specified and directed.

S & F Modular switch 1 way 16A, 240 Volts 1 module 230 Volts complete including taking down unserviceable one all as specified and directed.

S & F ceiling rose surface bakelight two to three terminal.

S & F Modular Bell push 6A 1 module complete including taking down unserviceable one all as specified and directed.

S & F Modular Socket, 6A - 2/3 pin combined 2 module complete including taking down unserviceable one all as specified and directed.

S & F Modular Fan step regulator, 120W, 240 Volts 2 module complete including taking down unserviceable one all as specified and directed.

S & F Decorative Endura Linear Neo LED lighting fixture 10 Watt, 6000K, (581mm) with extruded Al. heat sink, environmental friendly, energy efficient ready to use pack.housing with reflector cover channel, with electronic driver, holder, inclding LED tube 10 Watt connector block, etc. complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including taking down unserviceable one all as specified and directed. Make - Havells cat Part No. LHEWEBP7IN1W010 /Wipro/Bajaj/Crompton/Philips

S & F Electronic step type Fan regulator 120/280 Watt capacity including connecting up complete.

S & F Decorative ultra slim linear LED lighting fixture 20 Watt with extruded Al. heat sink, environmental friendly, energy efficient ready to use pack housing with reflector cover channel, with electronic driver, holder, inclding LED tube 20 Watt connector block, etc. complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including taking down unserviceable one all as specified and directed. Make - Havells cat Part No. LHEXBHP7PN1W020 /Wipro/Bajaj/Crompton/Philips

S & F Sheet metal enclosure MCB DB single pole and neutral, 8 way 240 Volts with 200 Amps rated bus bar double door type with blanking plates wherever reqired complete.

S & F MCB double pole 240 Volts 16 to 40 Amps complete including taking down unserviceable one all as specified and directed.

S & F MCB single pole 240 Volts 6 to 32 Amps complete including taking down unserviceable one all as specified and directed.

Earthing complete with glavanised steel earth plate elactrode 600x600x6.0 mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below ground leves)with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nut , bolt, check nut and washer of galvanised iron or of steel, earth lead protected by 15 mm dia GI pipe light grade watering pipe 20 mm dia GI light grade GI wire meshed funnel alternate layer of charcoal and salt PCC chamber , reassed for and including RCC cover including all necessary excavation and earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate no 5 of MES SSR Pt-I 1991 print and as directed.

S & F sheet metal enclosure MCB DB double door 4 way tripple pole and neutral 415 Volts complete including taking down unserviceable one all as specified and directed.

Supply and Fix Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP/DP 10A- 20 Amps with complete accessories all as specified and as directed and directed by Engr in Charge as per site requirement. Make :- Havells Cat Part No - DHDPUDP020/Legrand/C&S/Siemens/Standered

S & F MCB TPN 63 Amp 440 volts complete including taking down unserviceable one all as specified and directed.

Repair and Replacement for LED street light fitting made out of pressure dia cast aluminium housing with highn power LED as lighting source and lens embedded PC cover having TOP OPENING seperate driver compartment with IP66 protection and impact resistance of IK07 with10KV Built-in Surge Protective Device (LED lamp suitable for 60 Watts, 240 Volts, AC, 50Hz) and GI pipe 40 mm dia, light grade for mounting bracket bent to shape 1.50 RM and fixing arrangement with two Nos of MS clamps set, nut bolts, washers of suitable size complete including taking down unserviceable one all as specified and directed. Make- Havells cat part No ENDURAPEARLPLUSSL60LED 757SASYTOPC/Wipro/Bajaj/Crompton/Philips

Taking down electric meter any type up to 40 Amps capacity keeping in safe custody and fixing the same after rewiring work completed including disconnecting and connecting up complete all as specified and directed.

M/s SHIVRATAN CONSTRUCTION

TANUJ CONST. CO.

Dashmesh Enterprises