Construction of RCC framed structure for Radio Radar MRO room and Electrical Instrument MRO room and Garrett Engine Dressing or Servicing cell with Controlled Environment Room near Steel Hangar at HAL TAD Kanpur

Name Of Work :“Construction of RCC framed structure for Radio Radar MRO room & Electrical Instrument MRO room and Garrett Engine Dressing/Servicing cell with Controlled Environment Room near Steel Hangar at HAL TAD Kanpur."

CA. No. MW/CIV/958/3/25-26

TECHNICAL BID Appendix ‘A’

PRE-QUALIFICATION DETAILS OF APPLICANTS

Note:1. Vendors may upload a separate sheet in prescribed format along with Annexures name and No., if space provided below is not sufficient.

2.Vendors are requested to write in the yellow shaded portion only.

Section 1: Applicant’s Particulars

Name of the Individual / Firm / Company:

Constitutional or Legal Status of the firm

Registration Number From ROC(If any): Registering Authority Date of Registration

Registered Address:

Contact Person Name & Designation:

Address for correspondence(If different from Regd.Address):

Tel. No. Fax No.

Mobile No. Email Address:

PAN/GIR No. (Copy to be attached) GSTIN (Copy to be attached)

(This declaration should be completed by a proprietor, partner, director or other senior manager who has the authority to do so.)

‘I accept the HAL terms & conditions for this contract and declare that the particulars shown herein are true & correct in every detail.’

Details of persons holding the power of Attorney [If different from above]

(Upload, attested copy of Notarized Power of Attorney)

Name Tel No.: Mob:

Position Fax No.:

Section 2: Applicant’s Profile

2.1 Detail of registration of the firm if available with different following organizations (Attach necessary certificates from the registering authorities):

Company Registration Number Dated Validity Value of Contract for which Registered Class/Type of Registration

HAL or its Division

Others(if any) (Specify).

2.2 Upload Company’s Memorandum of Association and Articles of Association / to be enclosed. Board resolution paper may be enclosed along with the memorandum of association (in case of Pvt.Ltd./Ltd.Co.) / Partnership Deed (in case of Partnership firm). (Write Enclosed / Not Enclosed) .

2.3 Information on litigation history, in which the Bidder is involved (Write Yes/No in Col.5).

Other party(ies) (Dispute involved with) Name of Employer Cause of dispute Amount involved. Remarks showing present status. (Write Yes/No )

Details Attached (if Yes) [Write attached / Not attached].

2.4 In the last 5 years, has your firm, or any firm with which any of your company’s owners, officers, partners were associated, been debarred, disqualified, removed, blacklisted or otherwise prevented from bidding or completing any contract (Write Yes / No).

If yes, state the project and the basis for the action.

Section 3 – Prequalification criteria

3.1 Solvency for a minimum value of Rs. 32.62 Lakh issued within a period of 12 months from the final date of submission of tender. i.e on or after 13.01.2025. In solvency certificate, solvent / solvency word must be mentioned failing which tender are liable to be rejected.

Name of Bank & Branch Bank’s Reference and Date Value Rs. In Lakhs

3.2 Annual turnover in the past 3 years ending 31-03-2025.

Note:- The annual turnover should be supported with audited financial statements and profit & loss statement of the concerned year with UDIN no. The average annual turnover for the last three years (starting from 2022-23 onwards) as above should not be less than 30 (Thirty) % (Rs. 24.46 Lakh) of the estimated cost as indicated in the tender document. It is mandatory to furnish all the three year annual turnovers failing which tender are liable to be rejected.

Financial Year (Assessment year shall not be considered) Annual Turnover (Rs. In Lakh) Average Annual Turnover for last three Years ( Rs. In Lakh)

3.3 Experience details

Experience of having successfully completed similar works during last seven (07) years starting (From 13.01.2019 to 12.01.2026) should either of the following. (Work completed as a whole only shall be considered as experience; Ongoing work / partially Completed works / Work-orders shall not be considered as experience certificate). Scanned copy of experience certificate must be uploaded. (a) ONE similar completed work costing not less than 80% (Rs. 65.23 Lakh) of the amount put to tender.

S. No. Name of the Work Date Of Completion Completed Cost Completion Certificate [Mandatory] Write Enclosed/Not Enclosed Name, address & Phone no. of the client

(b) TWO similar completed works costing not less than 50% (Rs. 40.77 Lakh) of the amount put to tender

S. No. Name of the Work Date Of Completion Completed Cost Completion Certificate [Mandatory] Write Enclosed/Not Enclosed Name, address & Phone no. of the client

(c) THREE similar completed works costing not less than 40% (Rs. 32.62 Lakh) of the amount put to tender.

S. No. Name of the Work Date Of Completion Completed Cost Completion Certificate [Mandatory] Write Enclosed/ Not Enclosed Name, address & Phone no. of the client

Note:- Completion certificate issued by the client should contain Completed value of the work, date of completion, duly supported by Work-order copy & agreement copy. TDS certificate for full completion value is to be enclosed in case the client is a private firm. Tender offer shall be liable for REJECTION if the tenderer has not furnished the Completion certificate.

Similar Works -Experience in carrying out Civil works shall be considered as similar works etc.

Section 4 - Declaration

4.1 I/We declare and confirm that -

a. All information and attachments submitted in this application are true and correct.

b. I/We are aware that any false information provided herein will result in the rejection of my application and suspension of any registrations granted.

c. I/We shall not make refund claims of expenditure incurred in processing this application.

4.2 I/We enclose herewith a pay order / banker’s draft number: drawn on Bank:

Branch & address Name

Date: Designation:

HINDUSTAN AERONAUTICS LIMITED ACCESSORIES COMPLEX TRANSPORT AIRCRAFT DIVISION, KANPUR CIVIL WORKS DEPARTMENT

NAME OF THE WORK: “Construction of RCC framed structure for Radio Radar MRO room & Electrical Instrument MRO room and Garrett Engine Dressing/Servicing cell with Controlled Environment Room near Steel Hangar at HAL TAD Kanpur. " CONTRACT NO. MW/CIV/958/3/25-26

PRICE BID (Schedule A Bill of Quantity )

Name of the Tenderer:

Sl. No Specification Qty. Unit Rate in Figs [Excluding GST & Welfare cess] Rate in words Amount

1 The work in general shall be carried out as per CPWD DAR 2023. For item of works not covered in the CPWD DAR shall be governed as per BIS specification or as per Sound Engineering practice or as specified and directed by the EIC.

2 Contractors shall inspect the site and fully acquaint himself / themselves with the scope and nature of work, access, location and working condition. No claim will be considered later on the ground of ignorance or otherwise of the conditions under which the work will be have to be executed.

3 This BOQ specifications have to be read in conjunction with detailed technical specification and tender drawings if any.

4 The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered.

5 The quoted percentage for the works mentioned below, shall be taken into consideration for evaluation of the tender. The lowest offer (L-1) will be determined considering the total amount including GST & Welfare cess based on the quoted percentage. HAL shall process the bills of contractor for executed work exclusive of GST & Welfare cess. In addition, payment towards GST & Welfare cess as applicable shall be made to the contractor along with the bills as per Bill Amount. The GST & Welfare cess paid by HAL shall be deposited to the concerned Govt. authority by the contractor regularly. Any other tax (as applicable) as imposed by the Govt. on the contract shall be borne by the contractor.

6 Contractors will be solely responsible for any accidents to workmen engaged by them during execution of work.

7 All materials required for the work will be contractors own supply. They shall conform to relevant IS standards and shall be of approved brand /manufacture as specified. If the specified brand/manufacture not available, then only alternative equivalent brand may be produced for approval. However, prior approval of HAL shall be taken before procurement of any material.

8 Any plant and machinery required are contractors own supply. No plant and machinery will be issued by HAL.

9 All the items shall be carried out as per the Specifications and as directed and approved by EIC.

10 The cement used in the work shall be of approved makes such as Jay Pee, Birla, ACC, Prism, Mycem or equivalent as approved by EIC.

11 Rate shall be inclusive of work at any height / level, lead & lift and staging, scaffolding etc.

12 Name & Address of the firm must be filled in the yellow shaded portion on the top of the page

1 Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 em deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil, as directed by EIC. 381.00 Sq.Mt. 28.70 Rupees Twenty Eight and Seventy Paise 10934.70

2 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50metres lead as per direction of Engineer - in- charge. 45.00 Cum 2984.24 Rupees Two Thousand Nine Hundred Eighty Four and Twenty Four Paise 134290.80

3 Earth work in excavation by mechanical means {Hydraulic excavator)/manual means over areas (exceeding 30 em in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, All kinds of soil, as directed by EIC. 222.00 Cu.Mt. 149.16 Rupees One Hundred Forty Nine and Sixteen Paise 33113.52

4 Providing and laying in position cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from naturalsources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) of specified grade excluding the cost of centering and shuttering -All work up to plinth level: as directed by EIC. 80.00 Cu.Mt. 5724.37 Rupees Five Thousand Seven Hundred Twenty Four and Thirty Seven Paise 457949.60

5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. as directed by EIC. 39.00 Cu.Mt. 164.71 Rupees One Hundred Sixty Four and Seventy One Paise 6423.69

6 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level RCC 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) as directed by EIC. 55.00 Cum 7009.12 Rupees Seven Thousand Nine and Twelve Paise 385501.60

7 Providing and laying cement concrete 1:1½:3 (1 cement : 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing as directed by EIC. 90.00 Cu.Mt. 8703.82 Rupees Eight Thousand Seven Hundred Three and Eighty Two Paise 783343.80

8 Steel reinforcement ( Thermo mechenically treated bars of grade Fe 500 D or more ) for R.C.C. work ready to use cut and bend rebars of approve make from factory / work shop to constrction site including placing in position and bending all complete above plith level / upto plith level as directed by EIC. 11000.00 Kg 83.74 Rupees Eighty Three and Seventy Four Paise 921140.00

9 Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete as directed by EIC. 100.00 Sq.Mt. 329.54 Rupees Three Hundred Twenty Nine and Fifty Four Paise 32954.00

10 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers as directed by EIC. 308.00 Sq.Mt. 618.82 Rupees Six Hundred Eighteen and Eighty Two Paise 190596.56

11 Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick as directed by EIC. 292.00 Sq.Mt. 864.20 Rupees Eight Hundred Sixty Four and Twenty Paise 252346.40

12 Providing and fixing 18 mm thick Granite stone slab colour black, Cherry/Ruby red gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab upto 0.50 sqm Granite stone slab colour black, Cherry/Ruby red as directed by EIC. 39.00 Sq.Mt. 4549.16 Rupees Four Thousand Five Hundred Forty Nine and Sixteen Paise 177417.24

13 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with M.S hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (Frame size 50 x 100 mm) Note: (M.S hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/ window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variationin profile dimensions on plus side shall be acceptable but no extra payment \on this account shall be made. as directed by EIC. 25.00 Meter 796.39 Rupees Seven Hundred Ninety Six and Thirty Nine Paise 19909.75

14 Providing and fixing 35 mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-15In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). Note: (M.S hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/ window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variationin profile dimensions on plus side shall be acceptable but no extra payment \on this account shall be made. as directed by EIC. 15.00 Sq.Mt. 4214.58 Rupees Four Thousand Two Hundred Fourteen and Fifty Eight Paise 63218.70

15 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineerin-charge. With stainless steel cover plate minimum 1.25 mm thickness as directed by EIC. 3.00 Each 2372.98 Rupees Two Thousand Three Hundred Seventy Two and Ninety Eight Paise 7118.94

16 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. as directed by EIC. 3.00 Each 945.25 Rupees Nine Hundred Forty Five and Twenty Five Paise 2835.75

17 Providing and fixing 300x16 mm aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete as directed by EIC. 3.00 Each 254.83 Rupees Two Hundred Fifty Four and Eighty Three Paise 764.49

18 Providing and fixing 300x10 mm aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessaryscrews etc. complete as directed by EIC. 3.00 Each 109.33 Rupees One Hundred Nine and Thirty Three Paise 327.99

19 Providing and fixing 150x10 mm aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessaryscrews etc. complete as directed by EIC. 3.00 Each 69.37 Rupees Sixty Nine and Thirty Seven Paise 208.11

20 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper as directed by EIC. 3.00 Each 60.80 Rupees Sixty and Eighty Paise 182.40

21 Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete as directed by EIC. 3.00 Each 730.21 Rupees Seven Hundred Thirty and Twenty One Paise 2190.63

22 Providing and fixing 125 mm bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete as directed by EIC. 3.00 Each 100.17 Rupees One Hundred and Seventeen Paise 300.51

23 Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of EIC. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by EIC.Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all wind speeds Fixed window / ventilator with mullion / transom. Using R1 series with frame (33mm & above ) x (35mm & above) & mullion (33mm & above) x (50mm & above). (Height upto 0.90 metre) all complete as directed by EIC. 11.00 Sq.Mt. 7693.45 Rupees Seven Thousand Six Hundred Ninety Three and Forty Five Paise 84627.95

24 Structural steel work riveted, bolted or welded in built up sections of JINDAL/TATA/SAIL/ISPAT/VIZAG for trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as directed by EIC. 1200.00 Kg 112.35 Rupees One Hundred Twelve and Thirty Five Paise 134820.00

25 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete as directed by EIC. 150.00 Sq.Mt. 887.52 Rupees Eight Hundred Eighty Seven and Fifty Two Paise 133128.00

26 Providing and laying Glazed Vitrified tiles 600x600 mm Matt/Antiskid finish of size (Thickness not less than 8 mm) in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. as directed by EIC. 250.00 Sq.Mt. 1230.97 Rupees One Thousand Two Hundred Thirty and Ninety Seven Paise 307742.50

27 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes 110 mm diameterconforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes as directed by EIC. 70.00 Meter 317.14 Rupees Three Hundred Seventeen and Fourteen Paise 22199.80

28 Providing and fixing 110 mm Coupler on wall face unplasticised -PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion as directed by EIC. 10.00 Each 114.41 Rupees One Hundred Fourteen and Forty One Paise 1144.10

29 Providing and fixing 110 mm Coupler on wall face unplasticised -PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water Bend conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion as directed by EIC. 15.00 Each 126.34 Rupees One Hundred Twenty Six and Thirty Four Paise 1895.10

30 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc With average thickness of 120 mm and minimum thickness at khurra as 65 mm. consisting of following operations: (a)Applying a slurry coat of neat cement using 2.75 g/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b)Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c)After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by EIC. (d)Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e)The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the EIC: 238.00 Sq.Mt. 1415.63 Rupees One Thousand Four Hundred Fifteen and Sixty Three Paise 336919.94

31 Making khurras 45x45 cm with average minimum thickness of5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm ) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 20.00 Each 250.63 Rupees Two Hundred Fifty and Sixty Three Paise 5012.60

32 Providing and fixing With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 as per IS 8225:1987, Light reflectance of 85%. Non combustible as per BS:476 (part-4), fire performance as per BS:476, humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on inter-locking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 mm reveal profile (white/ black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. GI perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the EIC. 174.00 Sq.Mt. 2210.42 Rupees Two Thousand Two Hundred Ten and Forty Two Paise 384613.08

33 Providing, rendering, screeding, dubbing out cement plaster in cement mortar 1:6 ( 1Cement : 6 Coarse sand) 12 mm average thickness, work upto at any height/depth on brick or concrete surfaces of any description fair / rough side, finishing fair trowelled to a smooth and even finish without using extra cement, including scaffolding, curing etc. complete as directed & approved by EIC. 627.00 Sq.Mt. 288.78 Rupees Two Hundred Eighty Eight and Seventy Eight Paise 181065.06

34 Finishing walls with water proofing cement paint of required shade .New work (Two or more coats applied @ 3.84 kg/10 sqm) External Surface as directed by EIC. 472.00 Sq.Mt. 98.24 Rupees Ninety Eight and Twenty Four Paise 46369.28

35 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm Internal Surface as directed by EIC. 390.00 Sq.Mt. 162.77 Rupees One Hundred Sixty Two and Seventy Seven Paise 63480.30

36 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture as directed by EIC. 100.00 Sq.Mt. 190.13 Rupees One Hundred Ninety and Thirteen Paise 19013.00

37 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Internal and External Surface as directed by EIC. 627.00 Sq.Mt. 131.13 Rupees One Hundred Thirty One and Thirteen Paise 82218.51

38 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling & dressing & finishing the top smooth as directed by EIC. 86.00 Sq.Mt. 629.66 Rupees Six Hundred Twenty Nine and Sixty Six Paise 54150.76

39 Providing and Fixing make white vitreous china flat back half stall Urinal of size 580x380x350mm with white PVC automatic flushing cistren, white fitting, standerd size CP brass flush pipe, spreaders with unions and clamp (all in CP brass) with waste fitting as per IS: 2556, CI trap with outlet grating and other coupling in CP brass, including painting of fitting and cutting and making good the wall and floor wherever required single half stall Urinal with 5 Litre PVC automatic flushing cistern of approved quality & make Jaquar/ Hindware/ Paryware/ Johnson/ Belmonte/ Kohler all complete.as directed by EIC. 1.00 Each 10144.33 Rupees Ten Thousand One Hundred Forty Four and Thirty Three Paise 10144.33

40 Supply & Fixing of Under Counter Basin wih Fixing Accessories, Size 605 x 410 x 200 MM, Shpae-Rectangular including Bottle Trap (with internal partition)32mm size with 300mm & 190mm long wall connection pipe & wall flange, Waste Coupling 32mm size full thread with 80mm height, bib cock with wall flange, 450mm long braided hose with M10 x 1 nipple, 15mm nut, O-ring & rubber washer (suitable for basin mixer) in all complete as directed by EIC. 1.00 Each 7473.95 Rupees Seven Thousand Four Hundred Seventy Three and Ninety Five Paise 7473.95

41 Providing & fixing ovel shape 450x350mm outer dimensions mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing as directed by EIC. 1.00 Each 1157.23 Rupees One Thousand One Hundred Fifty Seven and Twenty Three Paise 1157.23

42 Providing & fixing of angular stop cock with triangular handle and wall flange, in all complete as directed by EIC. 1.00 Each 530.25 Rupees Five Hundred Thirty and Twenty Five Paise 530.25

43 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as directed by EIC. 1.00 Each 1351.22 Rupees One Thousand Three Hundred Fifty One and Twenty Two Paise 1351.22

44 Providing and fixing C.P. brass toilet paper holder as directed by EIC. 1.00 Each 675.38 Rupees Six Hundred Seventy Five and Thirty Eight Paise 675.38

45 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid approved quality & make Cera / Hindware/ Paryware/ Johnson with all fittings and fixtures complete as directed by EIC. 1.00 Each 6728.24 Rupees Six Thousand Seven Hundred Twenty Eight and Twenty Four Paise 6728.24

46 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.(450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.) as directed by EIC. 1.00 Each 565.88 Rupees Five Hundred Sixty Five and Eighty Eight Paise 565.88

47 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 15 mm nominal outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. as directed by EIC. 30.00 Meter 418.32 Rupees Four Hundred Eighteen and Thirty Two Paise 12549.60

48 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 20 mm nominal outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc as directed by EIC. 30.00 Meter 451.76 Rupees Four Hundred Fifty One and Seventy Six Paise 13552.80

49 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 25 mm nominal outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. as directed by EIC. 30.00 Meter 527.10 Rupees Five Hundred Twenty Seven and Ten Paise 15813.00

50 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 32 mm nominal outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. as directed by EIC. 30.00 Meter 621.26 Rupees Six Hundred Twenty One and Twenty Six Paise 18637.80

51 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 80 mm nominal inner dia., having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work as directed by EIC. 15.00 Meter 1820.46 Rupees One Thousand Eight Hundred Twenty and Forty Six Paise 27306.90

52 Providing and fixing G.I. pipes 32 mm dia nominal bore complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal Work - Exposed on Wall as directed by EIC. 10.00 Meter 560.50 Rupees Five Hundred Sixty and Fifty Paise 5605.00

53 Providing and fixing G.I. pipes 40 mm dia nominal bore complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal Work - Exposed on Wall as directed by EIC. 10.00 Meter 682.27 Rupees Six Hundred Eighty Two and Twenty Seven Paise 6822.70

54 Providing and fixing G.I. pipes 50 mm dia nominal bore complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal Work - Exposed on Wall as directed by EIC. 10.00 Meter 880.97 Rupees Eight Hundred Eighty and Ninety Seven Paise 8809.70

55 Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately). as directed by EIC. 1.00 Each 682.61 Rupees Six Hundred Eighty Two and Sixty One Paise 682.61

56 Providing and fixing 15 mm nominal bore brass stop cock of approved quality as directed by EIC. 1.00 Each 296.85 Rupees Two Hundred Ninety Six and Eighty Five Paise 296.85

57 Providing and fixing gun metal gate valve 25 mm nominal bore with C.I. wheel of approved quality (screwed end) : as directed by EIC. 1.00 Each 523.03 Rupees Five Hundred Twenty Three and Three Paise 523.03

58 Providing and fixing gun metal gate valve 32 mm nominal bore with C.I. wheel of approved quality (screwed end) : as directed by EIC. 1.00 Each 579.50 Rupees Five Hundred Seventy Nine and Fifty Paise 579.50

59 Providing and fixing gun metal gate valve 50 mm nominal bore with C.I. wheel of approved quality (screwed end) : as directed by EIC. 1.00 Each 862.73 Rupees Eight Hundred Sixty Two and Seventy Three Paise 862.73

60 Providing and fixing ball valve (brass) 15 mm nominal bore of approved quality, High or low pressure, with plastic floats complete : as directed by EIC. 1.00 Each 341.89 Rupees Three Hundred Forty One and Eighty Nine Paise 341.89

61 Providing and fixing ball valve (brass) 25 mm nominal bore of approved quality, High or low pressure, with plastic floats complete : as directed by EIC. 1.00 Each 389.96 Rupees Three Hundred Eighty Nine and Ninety Six Paise 389.96

62 Providing and fixing uplasticised PVC connection pipe 15 mm nominal bore and 45 cm length with brass unions : as directed by EIC. 1.00 Each 82.14 Rupees Eighty Two and Fourteen Paise 82.14

63 Providing and fixing C.P. brass shower rose 150 mm diameter with 15 or 20 mm inlet : as directed by EIC. 1.00 Each 186.85 Rupees One Hundred Eighty Six and Eighty Five Paise 186.85

64 Painting G.I. pipes 32 mm diameter and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work : as directed by EIC. 5.00 Meter 30.55 Rupees Thirty and Fifty Five Paise 152.75

65 Painting G.I. pipes 40 mm diameter and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work as directed by EIC. 10.00 Meter 35.84 Rupees Thirty Five and Eighty Four Paise 358.40

66 Painting G.I. pipes 50 mm diameter and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work as directed by EIC. 5.00 Meter 42.86 Rupees Forty Two and Eighty Six Paise 214.30

67 Providing and fixing G.I. Union 15 mm nominal bore in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) as directed by EIC. 1.00 Each 267.52 Rupees Two Hundred Sixty Seven and Fifty Two Paise 267.52

68 Providing and fixing G.I. Union 20 mm nominal bore in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) as directed by EIC. 1.00 Each 291.43 Rupees Two Hundred Ninety One and Forty Three Paise 291.43

69 Providing and fixing G.I. Union 25 mm nominal bore in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) as directed by EIC. 1.00 Each 369.12 Rupees Three Hundred Sixty Nine and Twelve Paise 369.12

70 Providing and fixing G.I. Union 32 mm nominal bore in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) as directed by EIC. 1.00 Each 410.97 Rupees Four Hundred Ten and Ninety Seven Paise 410.97

71 Providing and fixing G.I. Union 40 mm nominal bore in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) as directed by EIC. 1.00 Each 530.50 Rupees Five Hundred Thirty and Fifty Paise 530.50

72 Providing and fixing G.I. Union 50 mm nominal bore in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) as directed by EIC. 1.00 Each 692.27 Rupees Six Hundred Ninety Two and Twenty Seven Paise 692.27

73 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank as directed by EIC. 2000.00 Litre 9.24 Rupees Nine and Twenty Four Paise 18480.00

74 Providing and fixing C.P. brass long body bib cock 15 mm nominal bore of approved quality conforming to IS standards and weighing not less than 690 gms as directed by EIC. 1.00 Each 671.39 Rupees Six Hundred Seventy One and Thirty Nine Paise 671.39

75 Providing and fixing C.P. brass angle valve 15 mm nominal bore for basin mixer and geyser points of approved quality conforming to IS:8931 as directed by EIC. 1.00 Each 482.61 Rupees Four Hundred Eighty Two and Sixty One Paise 482.61

76 Providing and fixing PTMT grating 100 mm nominal dia. Circular type. of approved quality and colour. as directed by EIC. 3.00 Each 31.60 Rupees Thirty One and Sixty Paise 94.80

77 Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms as directed by EIC. 1.00 Each 93.66 Rupees Ninety Three and Sixty Six Paise 93.66

78 Constructing brick masonry manhole with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design: Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) as directed by EIC. 1.00 Each 10731.55 Rupees Ten Thousand Seven Hundred Thirty One and Fifty Five Paise 10731.55

79 Providing M.S. foot rests with 20x20 mm square bar including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design as directed by EIC. 5.00 Each 457.73 Rupees Four Hundred Fifty Seven and Seventy Three Paise 2288.65

80 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 (Rectangular shape 600x450 mm internal dimensions. as directed by EIC. 1.00 Each 1208.11 Rupees One Thousand Two Hundred Eight and Eleven Paise 1208.11

81 Making connection of drain or sewer line for pipes 250 to 300 mm diameter with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete as directed by EIC. 1.00 Each 775.13 Rupees Seven Hundred Seventy Five and Thirteen Paise 775.13

82 Brick work (1:6) with common burnt clay machine moulded moudular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10mm wide 12mm deep complete in cement mortar 1:6 (1 cement: 6 coarse sand) curved on plan for a mean radius not exceeding 6 m. from ground level upto plinth level as directed by EIC. 55.00 Cum 5880.17 Rupees Five Thousand Eight Hundred Eighty and Seventeen Paise 323409.35

83 Brick work (1:6) with common burnt clay machine moulded moudular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10mm wide 12mm deep complete in cement mortar 1:6 (1 cement: 6 coarse sand) curved on plan for a mean radius not exceeding 6 m. Above plinth level upto floor level as directed by EIC. 90.00 Cum 7538.74 Rupees Seven Thousand Five Hundred Thirty Eight and Seventy Four Paise 678486.60

84 Supplying & fixing two track powder coated glazed Aluminium bombay sliding window (Approx. size 1.2m x 1.2m ) of make such as HINDALCO/JINDAL/INDAL with outer frame of 63 x 38 x 2 mm Aluminium section and two track channel (Bottom / top &sides) of size 62 x 32 x 1.2mm, sliding shutters made of special Bombay sliding window section 38 x 19 x 1.2mm, all complete with 5mm thick float glass of MODI /ATUL/ SAINT GOBIN, edges wrapped in rubber beading, two nos roller of flyrail or equivalent make for each panel, powder coated Aluminium Handle & locking arrangement etc. all complete with labour material, wastage etc. Cost also include for P/F powder coated aluminium jali over existing frount weight not less than 2.250 Kg/sqm including & fixing F/Y/H channel all complete as directed & approved by EIC. 11.00 Sqm 6738.00 Rupees Six Thousand Seven Hundred Thirty Eight Only 74118.00

85 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make Kajaria/somani/Johnson in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. as directed by EIC. 150.00 Sqm 1065.50 Rupees One Thousand Sixty Five and Fifty Paise 159825.00

86 Consultancy for Architecural and structural work as per the following details:- 1. SITE ANALYSIS & FEASIBILITY STUDY (A) Assessment of the proposed site and other factor . 2. WORKING AND DETAILED ARCHITECTURAL DRAWING (A) 3D elevetion view (B) Architecural plan (C) Civil working layout (D) Dimension architectureral plan (E) Column layout plan (F) Details and shop drawing (as per requirement.) (G) Flooring laying plan (H) Excavation plan for footing (I) Sections (J) Elevations (K) Door windows chedule (if any required.) 3. WORKING AND DETAILED STRUCTURAL DRAWING (A) Column size drawing (B) Footing size drawing and laout plan (C) RCC roof plan (D) Beam layout plan 4. STRUCTURAL ANALYSIS (A) Calculation of load-bearing capacities and structural analysis 5. ESTIMATION (A) Revised estimate (if any) required after consultancy / during execution. 6. SITE VISIT (A) Site visit as per requirement to ensure the work as per architecture and structure 7. SUPPORT (A) Structural analysis report for structural stability 8. The Contractor has to submit duly vetted drawing from Government department or Government recognized Agency. 1.00 Job 95000.00 Rupees Ninety Five Thousand Only 95000.00

Sub-Total (Excluding GST & Welfare cess) Rupees Sixty Eight Lac Fifty Two Thousand Ninety and Eighty One Paise 6852090.81

The Tenderer has to Quote Percentage Above / Below as Specified and Percentage Shall be Quoted in Figures. Approximate Amount Put to Tender State Above or Below Quoted Percentage in Figures [Excluding GST & Welfare cess] Quoted Amount

Tenderer's Quote (Excluding GST & Welfare cess) 6852090.81 BELOW % 6852090.81

Add 18% GST Rupees Twelve Lac Thirty Three Thousand Three Hundred Seventy Six and Thirty Four Paise 1233376.35

Add 1% Welfare Cess Rupees Sixty Eight Thousand Five Hundred Twenty and Ninety Paise 68520.91

Grand Total (Including GST& Welfare cess) Rupees Eighty One Lac Fifty Three Thousand Nine Hundred Eighty Eight and Six Paise 8153988.06

Note: The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered.

WARNING: PLEASE ENTER PERCENTAGE QUOTE

HINDUSTAN AERONAUTICS LIMITED

ACCESSORIES COMPLEX

TRANSPORT AIRCRAFT DIVISION

CIVIL WORKS DEPARTMENT

ISSUED TO MR/MESSRS. SCHEDULE ‘A’ BILL OF QUANTITIES Sub: “Construction of Oil & Lubricant/ Chemical/ Consumable store at HAL Factory Kanpur.” Cont. No. : MW/CIV/370/1/14-15 Note : Sqm. denotes Square Meters Cum denotes Cubic Meters MT denotes Metric Tonnes Rm denotes Running Meters Ltr denotes Litres Kgs denotes Kilograms.

1. The work in general shall be carried out as per MES SSR 2010 . For item of works not covered in the SSR shall be governed as per BIS specification or as per Sound Engineering practice or as specified and directed by the Engineer-in-Charge.

2. The quoted rates shall be for the net finished work / item inclusive of cost of all necessary materials, machinery, tools and plant in all the operations described in the BOQ at all heights etc. All the required tests shall be carried out by the contractor at their cost in the presence of Engineer-in-Charge or his authorized representative and shall submitt the test results to the Engineer-in-Charge. If the test are carried out at an outside laboratory, the cost of such tests, materials, transportation, etc., shall be borne by the Contractor.

3. Contractors shall inspect the site and fully acquaint himself / themselves with the scope and nature of work, access, location and working condition. No claim will be considered later on the ground of ignorance or otherwise of the conditions under which the work will be have to be executed.

4. Contractors will be solely responsible for any accidents to workmen engaged by them during execution of work.

5 The rates quoted shall be inclusive of all taxes such as Sales Tax/VAT, Turnover Tax, Entry Tax, Service Tax (Contractor's portion as per the existing or amended rules from time to time), Sales Tax on Works Contract and all duties and levies like royalty, cess etc. HAL shall not reimbuse any taxes to the contractor under any circumstances. 5.1 RECOVERY OF SALES TAX/VAT AT SOURCE Sales Tax on works Contract will be recovered as per the rates indicated in UP Sales Tax act. The applicable sales Tax of the Gross value shall be deducted as per the provision of Law and the same will be remitted to the Tax Authorities on monthly basis. A certificate to this effect will be issued to the Contractors.

6. All materials required for the work will be contractors own supply. They shall conform to relevant IS standards and shall be of approved brand /manufacture as specified. If the specified brand/manufacture not available, then only alternative equivalent brand may be produced for approval. However, prior approval of HAL shall be taken before procurement of any material.

7. Bull dozers, power shovel, graders, loaders, Power road rollers, vibratory rollers, sheep foot rollers, and any other plant and machinery required are contractors own supply. No plant and machinery will be issued by HAL.

8.The Contractor may use Ready Mixed Concrete (R.M.C) without claiming for any extra cost subjected to satisfying the following conditions. The agency, which supplies R.M.C to be got approved by HAL.

9. For antitermite treatment and water proofing work contractor's has to furnish performance guarantee bond for five years on non judical stamp paper of Rs 100.00. Defect laibility of such items will be released after completion of guarantee period.

10. All the items shall be carried out as per the Specifications and as directred and approved by EIC.

HINDUSTAN AERONAUTICS LIMITED

TRANSPORT AIRCRAFT DIVISION-KANPUR

Sub: “Construction of Oil & Lubricant/ Chemical/ Consumable store at HAL Factory Kanpur.”

Cont. No. : MW/CIV/370/1/14-15

S.N. Description of Item Freak Item Qty. Unit Rate per unit in Figures Rate per unit in Words Amount (In Rs.)

1 Earth work in excavation in ordinary soil in trenches, not exc.1.50m depth and of any width, for foundation & other similar allied works etc. including cost of dressing / trimming sides and leveling / grading and ramming of bottoms of excavation, dewatering etc if required, getting out and return filling with excavated earth in layers of not exceeding 25cm thick including watering consolidating etc. & disposing the surplus excavated earth in the low lying area of factory within a lead of 500 mtrs etc. complete as directed &approved by EIC. (-) 275.00 Cum 100.00 Rupees One Hundred Only 27500.00

2 Providing and laying Plain cement concrete in 1:4:8 (1Cement : 4 Coarse sand: 8 stone aggregate of 40 mm nominal size) in foundation, floor or any description of work including cost of all operations such as manual / mechanical mixing, placing, compacting, scaffolding, side shuttering, curing etc . Complete as directed by EIC. 25.00 Cum 4000.00 Rupees Four Thousand Only 100000.00

3 Providing and laying brick work in walls, pillars, fascia, drain etc. in cement mortar 1:6 (1 cement : 6 coarse sand) in well burnt clay bricks, First class bricks, straight or curved in plan of any radius, in foundation and super- structure, work up to any height or depth including cost of scaffolding , raking out joints up to 1 cm depth as the work proceeds, curing etc. complete in all repect as per specification and direction of EIC. (+) 100.00 Cum 5000.00 Rupees Five Thousand Only 500000.00

4 -- do-- but half brick thick wall in CM 1:4. All complete as directed and approved by EIC. (+) 50.00 Sqm 700.00 Rupees Seven Hundred Only 35000.00

5 Providing, rendering, screeding and dubbing out plaster in cement mortar 1:3 (1cement: 3 Coarse Sand) of 5 mm thick on concrete surfaces at any height / depth of ceilings, column, beams, staircase, fins, fascia , drop etc. including trowelled to smooth and even finish without using extra cement, including cost of surface preparation, required scaffolding, curing etc. complete as directed & approved by EIC. 105.00 Sqm 150.00 Rupees One Hundred Fifty Only 15750.00

6 Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirting, drip moulds and similar work not exceeding 15cm in width or grith; including cutting to edges, all mitres and stopped ends etc. all complete as directed and approved by EIC. 120.00 RM 40.00 Rupees Forty Only 4800.00

7 Supplying and fixing in position steel reinforcement (TMT bars) conforming to IS-1786-1985 of any dia of approved make such as TATA/SAIL/ISPAT/VIZAG for slabs, beams, columns, footing or any other similar description of work, including cut to length, bent to shape as required, cranking bending , spirally or hooping, hooking ends and binding with mild steel wire soft drawn of not less than 0.9 mm dia, securing with chairs, placing in position and maintaining firmly so that placing and ramming of concrete will not displace it, removing rust and scales if any, wastage, etc. complete as directed & approved by EIC (Test report of manufacturer is to be submitted along with the supply). 12500.00 Kg 62.00 Rupees Sixty Two Only 775000.00

8 Providing and laying R.C.C 1:1 1/2:3 (1Cement : 11/2 Coarse sand: 3 stone aggregate of 20 mm nominal size) for foundation, beam, columns, lintels etc. or any description of work including manual / mechanical mixing, placing, compacting, lead & lifts, curing etc . Complete as directed by EIC. 70.00 Cum 6000.00 Rupees Six Thousand Only 420000.00

9 Providing and laying Ready Mixed cement Concrete ( Design Mix M-25 grade ) in slab, floor, pavments or simlar items, RMC (Ready Mixed Cement Concrete M- 25 grade, using 20mm graded granite aggregate and consolidated with mechanically vibrated needle and surface /screed vibrators and curing. Design mix to be got approved from EIC. If any additional quantity of cement over and above the minimum quantity of 300 Kgs per Cum is required as per the design mix/trial mix to achieve the specified strength, cost of the same shall be borne by the contractor. Note: Design Mix to be got approved by EIC before the work. 70.00 Cum 7000.00 Rupees Seven Thousand Only 490000.00

10 Providing and laying Plain cement concrete 1:2:4 (1 cement :2coarse sand : 4 stone coarse 12.5mm aggregate downgraded) 25mm thick in drain foundations, floors or in any description of including manual / mechanical mixing, placing, compacting, curing scaffolding, form work finishing the surface even and smooth using extra cement all complete as directed & approved by EIC. (+) 65.00 Sqm 300.00 Rupees Three Hundred Only 19500.00

11 Supplying & fixing two track powder coated glazed Aluminium bombay sliding window all complete with outer frame of 63 x 38 x 2 mm Aluminium section and two track channel (Bottom / top &sides) of size 62 x 32 x 1.2mm, sliding shutters made of special Bombay sliding window section 38 x 19 x 1.2mm, All complete with 5mm thick float glass of MODI/ SAINT GOBAIN, edges wrapped in rubber beading, two nos roller of flyrail , including providing and fixing powder coated aluminium grill , powder coated Aluminium Handle & locking arrangement etc. all , complete with labour material, wastage etc. all complete as directed & approved by EIC. (-) 25.00 Sqm 4000.00 Rupees Four Thousand Only 100000.00

12 Providing and fixing powder coated Aluminium grill having weight not less than 2.0 Kg/m2 of approved make such as (HINDALCO/JINDAL/INDAL) of approved design to the existing outer frame of Bombay sliding window including required fittings such as 'Y' channel all around the frame for properly securing the aluminium grill including circular cutting wherever directed for provision of Air cooler, all complete with cutting wastage etc. compete in all respect as per specification and direction of EIC . (+) 5.00 Sqm 3000.00 Rupees Three Thousand Only 15000.00

13 Providing, manufacturing and erecting partly glazed and partly panelled powder coated Aluminium parititions using standard sections of JINDAL, HINDALCO or equivalent as per approved design and drawing with bottom panel of 12mm thick prelaminated exterior grade particle board of reputed manufacturers such as Archid, Kitlam, Century confirming to 12823 and top panels with 5mm thick float glass as detailed below including necessary cleats, Screws, fastners etc., a) Top, middle, vertical and bottom members -100x 44 x2mm of weight 1.519Kg / RM forming grid not exceeding 1.00 Sqmt panel as approved. b) Glass - 5.00mm thick plain float glass of MODI / SAINTGOBAIN or equivalent c) Bottom Panels 12mm thick prelaminated exterior grade in top panal particle board. d) Rubber gaskets - Good quality of approved make e) Glazing clips - Weight of 0.097Kg/RM. (+) 10.00 Sqm 3500.00 Rupees Three Thousand Five Hundred Only 35000.00

14 Providing, manufacturing & fixing partly glazed partly panelled powder coated Aluminum hinged single doors with door frame shutter of approx. size 1.00 x 2.00 m of extruded section of JINDAL/HINDALCO with door frame section 100 x 44 x 2mm, vertical members, top and middle rails of door shutter of 83 x 44 x 2mm, bottom rail of door shuter of 114 x 44 x 2mm section, fixing the door to the wall with rawplugs and screws incluiding providing and fixing MS tie rod of 8mm for the door shutter, all as directed and approved be EIC. The quoted rate shall be inclusive of supplying and fixing following fixtures for each shutter. a) Aluminium body hydraulic door closer universal type of Everite / Hardwin or equivalent. 1 No. b) Powder coated Aluminium towerbolt of 200 mm long of extruded section (ISI marked only) 2 Nos. c) -----------do -----------Aldrop 250mm long 1 No. d)Internal locks of approved make 1 No. e) Powder coated Aluminium alloy handles fabricated type American 150mm ISI marked only 2 Nos. f) Aluminium powder coated butt hinges 100 mm long ISI marked 4 Nos. g) 5mm thick float glass of MODI/ SAINT GOBAIN for the upper portion of the door with good quality rubber beadings, powder coated Aluminum glazing chips. h) 12mm thick both sided pre-laminated exterior grade particle board confirming to IS 12823 of NOVAPAN/GREENLAM/FORMICA/SANDIK/SWARAJ or equivalent (ISI marks) for the lower portion of door shutter (approx. 1.00 mtr height) using powder coated Aluminium glazing clips, beading etc.as directed & approved by EIC. 25.00 Sqm 5000.00 Rupees Five Thousand Only 125000.00

15 Supplying & fixing acid proof non skid ceramic tiles of size 400x400mm x 9 mm thick (Approx size) in floor etc of Kajaria, Johnson & Johnson, Orient Bell, Somany, Nitco make etc of first quality (tiles sample as approved by EIC) for floors including providing and laying 15 mm nominal thick cement mortar screed bedding layer of CM 1:4 ( 1 cement : 4 coarse sand ) and fixing tile with cement slurry, over the existing floor, and preparation of surface by wire brush cleaning and wetting the surface with water and spreading cement slurry, including cost of raking the joints and pointing with tinted white cement, curing, cleaning including cutting of tiles, wastage and disposal of debris at directed place etc. complete as directed by EIC. [Note:- Tile sample to be got approved by EIC before laying]. (-) 250.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 325000.00

16 Supplying and fixing glazed ceramic wall tiles of first quality of reputed manufacturers such as Kajaria, Johnson & Johnson/ Orient Bell/ Somany/ Nitco tiles in dado and skirting of size (450x350x 7)mm thick or bigger size with 10 mm thick cement mortar screed bedding layer 1:4 ( 1 cement : 4 coarse sand ) cost of raking the joints and pointing with white cement mixed with matching tint finishing wall ( matching with floor tiles colour) / make all complete as directed & approved by EIC. (+) 50.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 65000.00

17 Providing & laying ultra tiles VENTURA-T of size 300 x 300 mm of approved design and shade in Treads and laid over 15mm thick cement mortar 1:4 bedding layer jointing with cement slurry matching the shade & pointing with white cement & pigment complete with labours, material wastage etc. as directed & approved by EIC. 10.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 13000.00

18 --do-- but VENTURA-R of size 152 x 300 mm for staircase risers over 15mm thick cement mortar in CM 1:4 complete all as directed & approved by EIC. (+) 5.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 6500.00

19 Providing & applying two coats oil bound distemper of approved colour with one coat of alkali resistant primer all of approved make such as Asian / Berger/ ICI or equivalent conforming to IS 428-1969 to walls, ceiling or of any description at any height, including providing and applying Birla white/Latafinish/JK white wall putty as per requirement of site for making surface even and smooth complete with cost of all materials, labour, wastage, safety measures, scaffolding, staging etc. as directed & approved by EIC. (+) 580.00 Sqm 150.00 Rupees One Hundred Fifty Only 87000.00

20 Providing & Applying two coat of premium acrylic silicon based weather resistant exterior paint including one coat of exterior primer such as weather coat long life / weather shield / Apex of reputed manufacturer including providing and applying Birla white/Latafinish/JK white/Myklatirat wall putty @ 0.40 Kg / Sqm for making surface even and smooth. All complete with labour, material ,required scaffolding, brushes and other tools & plants required for proper completion of work cleaning the splashes from door, windows and from other surfaces etc.complete as directed & approved by EIC. (+) 500.00 Sqm 150.00 Rupees One Hundred Fifty Only 75000.00

21 Supplying and fixing 110mm PVC, SWR single socketed pipe in any length with rubber ring joint laid in trenches or in floors for soil waste of approved make such as Supreme Kisan, Finolex, Prince or equivalent Conforming to IS: 4985-2000;(Class - 4) of complete with all required necessary fittings for fixing etc. complete as directed & approved by EIC . (-) 50.00 RM 200.00 Rupees Two Hundred Only 10000.00

22 Supplying and fixing PVC (SWR) bends of 110mm with access door socketed of Supreme, kisan, Finloex, Prince (ISI make) etc complete as directed & approved by EIC. (-) 10.00 Each 100.00 Rupees One Hundred Only 1000.00

23 Sand filling under floors or in foundations including watering and consolidation, complete as directed & approved by EIC. (-) 15.00 Cum 100.00 Rupees One Hundred Only 1500.00

24 Supplying & filling with aggregates of gauge 40 to 80mm broken stone or boulders in pits/ wells in layers including lead, lift, T & P etc. complete as directed & approved by EIC. (+) 10.00 Cum 2500.00 Rupees Two Thousand Five Hundred Only 25000.00

25 Drilling of 200mm dia boring hole 2m deep from ground level in soil including all tools & machinery and disposal of spoil upto a lead of 50m within the premises of factory etc. complete as directed & approved by EIC. (+) 1.00 Each 2000.00 Rupees Two Thousand Only 2000.00

26 Drilling of boring hole 200mm dia after 2 meter depth including all tools & machinery tools and disposal of spoil upto a lead of 50m within the premises of factory etc. complete as directed & approved by EIC Rate also included for making strata chart to be made for making slots in ribbed pipe. (+) 38.00 RM 1000.00 Rupees One Thousand Only 38000.00

27 Supplying & fixing 160mm dia PVC pipe of pressure rating 6 kg/ cm2 of approved make such as Supreme / Finolex / Prince (ISI make) with socket and fittings for complete job etc. complete as directed & approved by EIC. (-) 35.00 RM 250.00 Rupees Two Hundred Fifty Only 8750.00

28 Supplying & fixing 160mm dia PVC ribbed screen sloted pipe of pressure rating 6kg/ cm2 of approved make such as Supreme / Finolex /Prince (ISI make) with socket and fittings for complete job etc. complete as directed & approved by EIC. (Slot will be made in accordance with strata chart). (-) 6.00 RM 250.00 Rupees Two Hundred Fifty Only 1500.00

29 Providing & applying flush pointing in CM 1:3 in brick wall including raking out joints complete as directed & approved by EIC. (+) 50.00 Sqm 1000.00 Rupees One Thousand Only 50000.00

30 Supplying & Fixing cast iron work grade FG 150, unmachined, in gratings and similar articles exc. 5.00kg/each and as directed by EIC. (+) 2500.00 Kg 140.00 Rupees One Hundred Forty Only 350000.00

31 Providing, rendering , screeding and dubbing out in cement mortar 1:6 (1cement: 6 graded coarse sand)10mm thick, on rough or fair faces of brick/ concrete surfaces at any height / depth on wall, ceiling, fascia, etc. including trowelled to smooth and even finish without using extra cement, including cost of surface preparation , scaffolding, curing etc. complete as directed by EIC. (+) 1000.00 Sqm 180.00 Rupees One Hundred Eighty Only 180000.00

32 Supplying & fixing non-skid ceramic tiles of approx. size 400x400mm x 7-9 mm thick in floor, of reputed manufacturers such as Kajaria, Johnson & Johnson, Orient Bell, Somany, Nitco make of first quality , including providing and laying 15 mm nominal thickness cement mortar screed bedding layer of CM 1:6 ( 1 cement : 6 coarse sand ) and fixing tile with cement slurry and preparation of surface by wire brush cleaning and wetting the surface with water and spreading cement slurry. including cost of raking the joints and pointing with tinted white cement, curing, cleaning the tiles, including cutting of tiles, wastage and disposal of debris at directed place etc. complete as directed & approved by EIC. [Note:- Tile sample to be got approved by EIC before laying]. 12.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 15600.00

33 Supplying and fixing glazed ceramic wall tiles of first quality of reputed manufacturers such as Kajaria, Johnson & Johnson/ Orient Bell/ Somany/ Nitco tiles in dado and skirting, of size (450x350x 7)mm thick with cement slurry over sub- base of 10 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) cost of raking the joints and pointing with white cement mixed with matching tint finishing wall ( matching with floor tiles colour) / make all complete as directed & approved by EIC. 50.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 65000.00

34 Supplying and fixing in position set of coloured Glazed Vitreous China make oval shaped counter top wash Basin of Parryware or equivalent (design & colour as approved by EIC) of size 550 x 450 mm approx. including cost of 32 mm dia CP brass waste coupling, CP swan neck pillar cock, CP angle valve, CP bottle trap all CP fittings of Parryware / Plumber or equivalent make , complete in all respect as directed & approved by EIC. (+) 2.00 Each 8000.00 Rupees Eight Thousand Only 16000.00

35 Supplying and fixing urinal partition black granite on both side finish 18 - 20mm thick machine cut of size 90 cm X 50 cm (approx.) or required size to bedded and jointed grouted on wall in CM 1:2 and finishing edges with white cement and admixture pigment to match the shade of granite stone including cutting forming, round edge beading moulded in granite with polish complete in all respect including all labour, materials, T& P as per direction of EIC. 1.50 Sqm 2500.00 Rupees Two Thousand Five Hundred Only 3750.00

36 Supplying and fixing Red granite wash basin platform 20mm thick, one side polished, machine cut of required size to accommodate two oval shape wash basins, including making oval shape opening for two W.B. as per size of wash basin providing and laying bedding mortar in CM 1:4 , 15 mm and finishing & polishing the edges of granite and pointed with pigmented white cement to match the shade of granite stone including cutting forming, round edge beading moulded in granite with polish complete in all respect including all labour, materials, T& P as per direction of EIC. (-) 1.00 Sqm 2500.00 Rupees Two Thousand Five Hundred Only 2500.00

37 Providing and Fixing coloured Vitreous Chinaware coloured new magnum Urinal of Parryware or equivalent of size 635mmX395mmX420mm complete with providing and fixing plugs, bedding urinals in wall in cement mortar 1:2 ( 1 cement : 2 coarse sand), securing urinals to plugs with 60 mm long S.S screws, pointing around urinals back in cement. Complete with the following system:- (a) Providing & fixing 50mm PVC Pipe supreme make or equivalent about 750mm long concealed vertically in wall & reparing the wall with CM (1:3). (b) Providing & fixing CP Brass waste couplings and jointing with waste pipe & put in concealed pipe. (c) Providing & fixing 15mm CP Brass half turn fancy flush cock, to water line including all fittings fixture with CP Cover plate. (d) Providing & fixing CP spreader of make Parryware or equivalent 15mm dia with CP Pipe connector to urinal, all complete with required fitting & fixture T- elbow, Grating of C.P. Union, jointer connector etc. for proper functioning of urinal complete in all respect as directed & approved by EIC. (+) 3.00 Each 8000.00 Rupees Eight Thousand Only 24000.00

38 Supplying & Fixing in position coloured European Water Closet of vitreous china with 'P' or 'S' trap left or right bent of Parryware make or equivalent as per direction of EIC, with plastic seat cover and lid fixed with CP brass hinges and rubber buffers. Fixing of 10 litre capacity Plastic flushing cistern of Parryware Deluxe model make complete with all accessories such as inlet, ball valve, float, 15 mm dia PVC pipe connection,40 mm dia PVC flush pipe bent to shape with necessary connections, fittings and clamps PVC connection with union 15 mm dia overflow pipe with specials, providing and fixing 15 mm dia GI connections, GI over flow pipe with specials including cutting chases and finishing in walls after embedding of pipes , floors etc , where required with Cement mortar 1:3 ( 1cement: 3coarse sand )all complete including cost of painting of brackets( with red oxide primer and two coat of synthetic enamel paint). 1.00 Each 7000.00 Rupees Seven Thousand Only 7000.00

39 Supplying & Fixing factory made PVC solid panel door shutter 30 mm thick of approved manufacturer such as Rajshri Plastiwood/ Syntex/Polypan or equivalent brand factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mmx19 mm for stiles & 15 mm x 15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame shall be covered with 5 mm thick heat moulded Rajshri /Syntex/Polypan PVC 'C' channel of size 30x50 mm forming stiles, and 5 mm thick, 75 mm wide PVC sheets for top rail, lock rail & bottom rail on either side, and 10mm (5mmx2) thick, 20mmwide cross PVC sheet as gap insert for top rail & bottom rail. Panelling of 5 mm thick PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with 30 mm wide x5mm thick PVC sheet beading on either side, and join together with solvent cement adhesive.. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' channel using PVC solvent cement adhesive etc. complete as per direction of E -I-C, manufacturer's specification & drawing. Including all fittings such as aluminum tower bolt 150mm long 2 Nos.: Sliding door bolt 200mm long 1No & aluminum handle 100mm long 2no in each shutter as directed & approved by EIC. 4.20 Sqm 2800.00 Rupees Two Thousand Eight Hundred Only 11760.00

40 Supplying & Fixing factory made polyvinyl chloride (PVC) Door Frame of approved manufacturer such as Rajshri Plastiwood / Syntex/ Polypan of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet, mitre cut at two corners and joined with 2 nos. of 150 mm long brackets of 15x15mm M.S. Square tube. The two vertical door profiles are to be reinforced with 19x19 mm M.S. Square tube of 19 gauge,EPDM rubber gasket weather seal to be provided through out the frame. The door frame shall be fixed to the wall using 65/100 mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 4 nos. of screws to be provided for each vertical member & minimum 2nos. For horizontal member etc. complete as per manufacturers specification and direction of EIC. 15.00 Rm 500.00 Rupees Five Hundred Only 7500.00

41 Supplying & Fixing in position tilling /adjustable type LOUVERS of size 600 x 600mm, Louver strip fixed over aluminium frame made of powder coated aluminium section of 63 x 38 x 2mm and fixing of 3.00mm thick and 100 mm wide pinheaded glass strip etc. Complete as directed and approved by EIC. (-) 2.00 Each 200.00 Rupees Two Hundred Only 400.00

42 Supplying & Fixing Aluminium powder coated barrel tower bolt 200 mm long size of extruded section of approved qualtiy (ISI mark) with all accessories which is required and complete in all respect as directed & approved by EIC. (+) 6.00 Each 200.00 Rupees Two Hundred Only 1200.00

43 Supplying & Fixing Aluminum powder coated 150 mm long Handles (dull finish cast type of good quality having ISI mark) to each door shutter all complete as directed & approved by EIC. (+) 6.00 Each 125.00 Rupees One Hundred Twenty Five Only 750.00

44 Providing and fixing medium weight, cold rolled steel Butt hinges of 100 mm size fixed with screws for doors, windows etc. all complete with labour, material and fixing to wooden / MS frame, making cut outs in wooden frame for fixing hinges etc. complete as directed by EIC. 12.00 Each 50.00 Rupees Fifty Only 600.00

45(a) Supplying and Fixing of CP brass two way bib cock for 15 mm dia pipe of Plumber / GEM / L&K or equivalent approved make, including jointing with water supply lines, complete as directed by EIC . (+) 2.00 Each 1700.00 Rupees One Thousand Seven Hundred Only 3400.00

(b) Supplying and Fixing of CP brass long body fancy type bib cock for 15 mm dia pipe of Plumber / GEM / L&K or equivalent and approved make, including jointing with water supply lines, complete as directed by EIC . (+) 2.00 Each 1000.00 Rupees One Thousand Only 2000.00

46 Supplying and fixing of CP brass angle cock / valves of Plumber / GEM / L&K make for 15 mm dia pipe including jointing with water supply line and all complete operation for fixing including required accessories etc. complete as directed by EIC. (+) 3.00 Each 700.00 Rupees Seven Hundred Only 2100.00

47 Supplying and fixing 580 x 440 mm light coloured glaze porceline Indian water closet (Orissa Pattern) confirming to IS:2556 of make parryware or equivalent with'P' or 'S' trap with or without vent set, including supplying and fixing 10 Ltrs. Capacity valve less syphonic action type low level PVC cistern confirming to IS : 774, with brackets, 40mm dia PVC waste pipe with coupling, 15mm dia high density PVC inlet pipe connection, 15mm dia CP angle cock of parry ware all above of approved make, colour etc complete as approved, specified and directed by the EIC. (-) 1.00 Each 3000.00 Rupees Three Thousand Only 3000.00

48 Supplying and fixing of good quality bevelled edge looking mirror of 5mm thickness of approved manufacturer such as Modi Atul , saint -gobain etc of any size with AC Sheet backing and 1" wooden beading all round edges, all complete as per direction of EIC. (+) 0.90 Sqm 1000.00 Rupees One Thousand Only 900.00

49 (a) Supply & fixing of G.I. water tubing 15 mm dia (Galvanized Iron) TATA/ JINDAL/ ZENITH make of medium grade in required lengths with screwed socket joints, together with all tube, fittings (Such as bends, elbows, tees, short pieces, connectors back-nuts, diminishing pieces, caps, plugs and unions etc.) and fixing complete with clips, wall hooks, wooden plugs at suitable intervals including cost of cutting through walls, floors / roofs etc and their making good, laying in trenches etc. Also for cutting, screwing and waste, and for making forged bends on piping as required, connectors shall be inserted, where required or as directed by EIC. 28.00 RM 180.00 Rupees One Hundred Eighty Only 5040.00

(b ) ---do as above but 25 mm dia. (-) 6.00 RM 225.00 Rupees Two Hundred Twenty Five Only 1350.00

50 Supplying and fixing C.P Liquid soap Dispenser of any approved make/ branded hand push types including all fixing accessories and operations etc. complete as directed & approved by EIC. (-) 1.00 Each 300.00 Rupees Three Hundred Only 300.00

51 Supplying and fixing PVC floor trap 75 mm dia. of approved make such as supreme / Finolex/ Kisan/ Prince (ISI mark)with grating including jointing to waste PVC pipes with cement concrete 1:2:4 etc. complete as directed & approved by EIC. (-) 4.00 Each 200.00 Rupees Two Hundred Only 800.00

52 Supplying and fixing 110mm/ 75mm PVC, SWR single socketed pipe in any length with rubber ring joint fixed to walls, laid in trenches, under floor for soil waste of approved make such as Supreme Kisan, Finolex, Prince or equivalent Conforming to IS: 4985-2000;(Class - 4) complete with all required necessary fittings for fixing etc. complete as directed & approved by EIC for following dia. pipes

(a) 110 mm dia. (-) 3.00 RM 250.00 Rupees Two Hundred Fifty Only 750.00

(b) 75 mm dia. 10.00 RM 200.00 Rupees Two Hundred Only 2000.00

53 Supplying and fixing PVC (SWR) Junction single 'T' equal or unequal with access door for following dia. of Supreme, Kisan, Finolex, Prince (ISI make) etc. complete as directed & approved by EIC.

(a) 110 mm dia. (-) 2.00 Each 200.00 Rupees Two Hundred Only 400.00

(b) 75 mm dia. 4.00 Each 150.00 Rupees One Hundred Fifty Only 600.00

54 Supplying and fixing PVC (SWR) bends of any radius with access door for following dia. of pipes of Supreme, kisan, Finloex, Prince (ISI make) etc complete as directed & approved by EIC.

(a) 110 mm dia. 2.00 Each 200.00 Rupees Two Hundred Only 400.00

(b) 75 mm dia. 4.00 Each 150.00 Rupees One Hundred Fifty Only 600.00

55 Supplying and Fixing PVC(SWR) reducer 110 x 75 mm of Supreme, kisan, Finolex, Prince make etc. complete all as directed & approved by EIC. (+) 1.00 Each 150.00 Rupees One Hundred Fifty Only 150.00

56 Supplying and Fixing PVC(SWR) vent cowls 75 mm dia of Supreme, kisan, Finloex, Prince (ISI make) etc. complete all as directed & approved by EIC. (+) 1.00 Each 125.00 Rupees One Hundred Twenty Five Only 125.00

57 Supplying and fixing PVC water tanks of make Sintex/ Polycon/ Tirupati / Supreme rotational moulded polythelene water storage tanks 1000 Ltr. cylindrical vertical with closed top hoisted and fixed to position, three layer body, including providing and fixing PVC ball cock, tank connection and all required G.I. fittings etc. complete as directed and approved by EIC. (+) 1.00 Each 9000.00 Rupees Nine Thousand Only 9000.00

58 Providing and fixing to chowkhat 30 mm thick, single leaf, factory made flush door shutter conforming to IS- 2202( Part-I)-1983, of G-door, Minar, Swastik, Shatabadi make and ISI marked, solid core construction, with block board core and commercial types veneers face on one sides and other face is covered with decorative face veneer with lipping/frame to match etc. complete , flush door shall be free from twist or wrap in plane etc. including provision of suitable blocks for interlocks, latches or other fittings etc. complete as directed & approved by EIC. (+) 2.50 Sqm 2800.00 Rupees Two Thousand Eight Hundred Only 7000.00

59 Providing and fixing CP Brass health faucet with telephonic arrangement and hook etc. of Plumber / GEM / L&K/ or any other equivalent make complete with required fittings & accessories as per direction of EIC. (+) 1.00 Each 1100.00 Rupees One Thousand One Hundred Only 1100.00

60 Supplying & fixing C.P Bottle trap of Plumber / GEM / L&K or any other equivalent brand etc. complete and approved by EIC. 3.00 Each 1100.00 Rupees One Thousand One Hundred Only 3300.00

61 Supplying erection & fixing of sliding door of aluminium powder coated of vertical, top middle & bottom rails of section 100 x 44 x 2mm and stiles of Sec. 83 x 44 x 2mm including supplying & fixing of top panel with 5mm with figured glass, pinhead type & bottom panel with 12mm botttom pre-laminated board including cost of handle, lock, glazing clip, rubber beading, G.rails and sliding roller for sliding door Complete as directed & approved by EIC. 2.50 Sqm 4000.00 Rupees Four Thousand Only 10000.00

62 Supplying, fabricating and fixing Stair (framed) including stringers, treads, landing, railings, balusters, hand rails etc. including cleats, brakets, etc. including one coat of red oxide primer providing metal putty and sand papering for making the surface smooth and two coat of first quality synthetic enamel paints, complete all as directed & approved by EIC. 4500.00 Kg 100.00 Rupees One Hundred Only 450000.00

63 Providing, centring & shuttering for the sides and soffits of suspended slabs, lintels, beams, floor slabs, landing and similar work of any description, in required shape and size, with true line & plumb etc. with plywood, MS plates shuttering including oiling of the top surfaces of shuttering , all supports with MS or wooden braces, struts, balli, etc, including working scaffoldings, ladders, gangways as required, including removal of formwork & centring after the stripping period as described in MES-SSR- part-I & IS 456 2000 , etc complete as directed and approved by EIC. 550.00 Sqm 250.00 Rupees Two Hundred Fifty Only 137500.00

Amount in Rs. 4699675.00

Amount in words:- Fourty Six Lakh Ninty Nine Thousand Six Hundred Seventy Five Only.