01-TN/EE/PANDD/26-27

Uprooting and removing plants fromthe surface of walls parapet etc and making good damages. (Repairing of damages to be paid separately).(c) Large plant of girth of exposed stem above 150mm. but not exceeding 225 mm. lift upto 6 mtr. [P.W.D.(Bldg.). Page- 278, Item-10(c) & 3RD Corrigenda]

Removing scum form the bottom floor of service latrine washing the floor thoroughly and treating the same with liberal sprinkling of bleaching powder (including cost of bleaching power) [P.W.D.(Bldg.). Page- 26, Item-10(a) & 3RD Corrigenda]

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.(i) Pakur Variety [P.W.D.(Bldg.). Page- 26, Item-10(a) & 3RD Corrigenda]

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. [P.W.D.(Bldg.). Page- 16, Item-16&3rd Corrigenda]

Plaster with sand and cement mortar including rounding off corners or chamfering corners as directed and including raking out joints or roughening of concrete surface, curing with cost andcarriage of all materials. (a)With 4 : 1 cement mortar. ii)20 mm thick plaster [Ref : P.W.D.(Bldg.), Page -189 Item-1 (3rd Corrigenda)]

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:(B) Partly glazed partly panelled or fully glazed single leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. [P.W.D.(Bldg.). Page- 240, Item-10(a) & 3RD Corrigenda]

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).(a) 1st class Best Indian teak. [Ref : P.W.D.(Bldg.). Page- 114, Item-1.(b)]

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor.i) 50mm thick shutters with 25mm thick panel of size 30 to 45 cm.(b) Ordinary teak wood. [Ref: P.W.D.(Bldg.). Page- 117, Item - 1.(i).(a)]

Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessaryholes, chasing etc. in walls, floors etc. and making good damages complete. [Ref: P.W.D.(Bldg.). Page- 106, Item - 18]

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.ii) Grill weighing above 16 Kg./sq.mtr and above [Ref : P.W.D.(Bldg.).Page- 104, Item-13.(a).(i) & 3rd corri.]